Frigidaire TINSEB151WRRZ, 316137234 User Manual

INSTALLATION INSTRUCTIONS

Over The Range Microwave Oven

BEFORE YOU BEGIN

IMPORTANT

• inspector’s use.

IMPORTANT

• coordinates.

•

NOTE TO INSTALLER – Be sure to leave these

instructions with the Consumer.

•

NOTE TO CONSUMER – Keep these instructions for

future reference.

• SKILL LEVEL – Installation of this appliance requires basic mechanical and electrical skills.

Save these instructions for local

Observe all governing codes and

Read these instructions completely and carefully.

1 MOUNTING SPACE

This Microwave Oven/Hood requires a mounting space on a wall as shown in Figure 1. It is designed to be used with standard 12" wall cabinets.

12"

30"

15.5"

30" or more

Backsplash

At least 2"

from cooking

surface

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

• Please read all instructions thoroughly before installing the Over the Range Microwave Oven. Two people are recommended to install this product.

• If a new electrical outlet is required, its installation should be completed by a qualiﬁ ed electrician before the Microwave Oven is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.

2 WALL CONSTRUCTION

This Microwave Oven/Hood should be mounted against and supported by a ﬂ at vertical wall. The wall must be ﬂ at for proper installation. If the wall is not ﬂ at, use spacers to ﬁ ll in the gaps. Wall construction should be a minimum of 2" x 4" wood studding and ³⁄₈" or more thick dry wall or plaster/lath. The m ount ing sur faces m ust be capable of supporting w eight of 110 pounds—the oven and contents—AND the weight of all items which would normally be stored in the top cabinet above the unit.

The unit should be attached to a minimum of one 2" x 4" wall stud or two 2" x 3" wall studs.

To ﬁ nd the location of the studs, one of the following methods may be used:

A. Use a stud finder, a magnetic device which locates the

nails in the stud.

B. Use a hammer to tap lightly across the mounting surface

to find a solid sound. This will indicate stud location.

P/N 316137234

Figure 1

66" or more

from floor

The center of the stud can be located by probing the wall with a small nail to ﬁ nd the edges of the stud and then placing a mark halfway between the edges. The center of any adjacent studs will normally be 16" or 24" to either side of this mark.

NEED HELP?

For customers in the United States, call: 1-800-944-9044 For customers in Canada, call: 1-800-213-9397 (English)

1-800-668-4606 ext.8199 (French)

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

TINSEB151WRRZ

Printed in Thailand

INSTALLATION INSTRUCTIONS

3 ELECTRICAL GROUNDING INSTRUCTIONS

This appliance must be grounded. This oven is equipped with a cord having a grounding wire with a grounding plug. It must be p lugged i nto a wall r eceptacl e that is pr operly i nstall ed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current.

WARNING - Improper use of the grounding plug can result in a risk of electric shock.

ELECTRICAL REQUIREMENTS

The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE GROUNDING PIN FROM THE PLUG.

DO NOT USE AN EXTENSION CORD.

The Power Supply Cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit, single grounded receptacle. The receptacle should be located inside the cabinet directly above the Microwave Oven mounting location as shown in Figure 2.

NOTE:

1. If you have any questions about the grounding or electrical instructions, consult a qualiﬁ ed electrician or serviceperson.

2. Neither Electrolux nor the dealer can accept any liability for damage to the oven or personal injury resulting from failure to observe the correct electrical connection procedures.

4 HOOD EXHAUST DUCT

When the hood is vented to the outside, a hood exhaust duct is r equi red. All d uctwork m ust be metal; absolu tely do not use plastic duct. Check that all connections are made securely. Please read the following carefully:

EXHAUST CONNECTION: The hood exhaust has been designed to connect to a standard 3 ¹⁄₄" x 10" rectangular duct. If round duct is required, a rectangular-to-round adapter must be used.

REAR EXHAUST: If a rear or horizontal exhaust is to be used, care should be taken to align the exhaust with the space between the studs, or wall should be prepared at the time it is constructed by leaving enough space between wall studs to accommodate exhaust.

MAXIMUM DUCT LENGTH: For satisfactory air movement, the total duct length of 3 ¹⁄₄" x 10" rectangular or 6" diameter round duct should not exceed 140 feet.

Elbows, adapters, wall caps, roof caps, etc. present additional resistance to air ﬂ ow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total length, add the equivalent lengths of all transitions and adapters plus the length of all straight duct sections. Figure 3 shows the approximate feet of equivalent length of some typical ductwork parts. Use the values in parentheses for calculating air ﬂ ow resistance equivalent, which should total less than 140 feet.

Ground

Receptacle

Opening for Power Cord

Figure 2

90° Elbow (10 ft.)

90° Elbow (25 ft.)

45° Elbow (5 ft.)

Adaptor (5 ft.)

Wall cap (40 ft.)

Figure 3

10” Wide Elbow (10 ft.)

Roof cap (24 ft.)

INSTALLATION INSTRUCTIONS

5 TOOLS RECOMMENDED FOR

INSTALLATION

• Phillips Screwdriver

• Electric Drill

• ¹⁄₂", ⁵⁄₈" and ³⁄₃₂" Drill Bits

• 1 ¹⁄₂" Wood Bit or Metal Hole Cutter (if metal cabinet is used)

• Saw to cut exhaust opening (if needed)

• Protective Drop Cloth for product and range - you may also use carton for protection

• Scissors

• Pencil

• Measure

• Tape

6 INSTALLATION HARDWARE

The INSTALLATION HARDWARE (items 1 - 7 ) packed with the oven should contain the following:

Item Name Quantity

Wood Screw 5 x 35 mm 6 Toggle Bolt ³⁄₁₆" Top Cabinet Screw 5 x 85 mm 2 Flat Washer 30 mm diameter 2 Grommet 1 Tapping Screw 4 x 8 mm 4 Exhaust Damper Assembly 1 Grease Filter 2

7 PREPARATION OF THE OVEN

1. Open the bottom of the carton, bend the carton flaps back and tilt the oven over to rest on plastic foam pad. Lift carton off oven and remove all packing materials, Installation Instructions, Wall Template, Top Template, Charcoal Filter, Turntable and Turntable Support; however, DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the ceiling in the oven cavity. SAVE THE CARTON AS IT MAY MAKE INSTALLATION EASIER.

2. CHECK THE OVEN.

Check the oven for any damage, such as misaligned or

bent door, damaged door seals and sealing surfaces, broken or loose door hinges and latches and dents inside the cavity or on the door. If there is any damage, do not operate the oven and contact your dealer or Electrolux AUTHORIZED SERVICER.

Mounting Plate

Figure 5

Figure 4

Parts shown not to common scale.

+ 5 hidden pages