Frigidaire PLHS69EFSS0, PLHS67EFSB0, GLHS69EFPW0, GLHS69EFPB0, GLHS68EFW0 Owner’s Manual

...

;lance ......... 7

Controls... 7- 9

Looking inside .......... 10 ° 11

Automatic ice and Water

Dispenser ................ 12 =17

Food Storage

& Energy Saving Tips ....... 18

Normal Operating Sounds.. 19

Care & Cleaning ......... 20 =21

Warranty ..................... 22

EspaSol ........... 27

Before You Call

Solutions to

CommonProb=ems.............. 23 - 26

READ AND SAVE THESE INSTRUCTIONS p!. 2416951oo_0106)

CongratuIations on your purchase of a new refrigerator! We here at Electrolux Home Products, inc. are very proud of our product and we are completely committed to providing you with the best service possible. Your satisfaction is our #1 priority.

Please read this Use & Care Manual very carefully. It contains

valuable information on how to properly maintain your new

refrigerator. We know you'll enjoy your new refrigerator and Thank You for

choosing our product. We hope you consider us for future purchases.

PLEASE READ AND SAVETHESE INSTRUCTIONS This Use & Care Manual provides specific operating

instructions for your model Use your refrigerator only as instructed in this manual These instructions are not meant to

cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.

Pmeaserecord your modem and seriamnumbers below for

future reference.This information is found on the serial

plate tocated inside the refrigerator compartment.

Model Number: Serial Number:

Purchase Date:

Questions?

1-800-944-9044

(United States)

1-800-265-8352

(Canada)

or visit our web site at ww_',frigidaire, com

Extend Your Warranty Protection

With An

Extended Service Contract

OALL 1-800-944-9044

To Enjoy These Benefits:

Total freedom from repair bills so unexpected repairs won't upset your budget,

Fast, convenient toll-free service isjust a

phone call away, Top-quaJity repairs by factory-trained

experts, Quick access to genuine repJacement

parts so you can rest assured your

refrigerator is repaired with the proper

components,

Please attach sales receipt here for future reference.

PLEASE COMPLETE AND MAIL IN THE PRODUCT

REGISTRATION CARD INCLUDED WITH YOUR

REFRIGERATOR.

FORYOURSAFETY ,, Donotstoreorusegasoline,orotherflammableHquidsin

thevicinityofthisoranyotherappliance.Readproduct labelsforwarningsregardingflammabilityandother

hazards.

,, Donotoperatetherefrigeratorinthepresenceof

explosivefumes.

,, Avoidcontactwithanymovingpartsofautomaticice

maker.

,, RemovealIstaplesfromthecarton.Staplescancause

severecuts,andalsodestroyfinishesiftheycomein

contactwithotherappliancesorfurniture. CHILDSAFETY Destroyorrecyclethecarton,plasticbags,andanyexterior

wrappingmateriatimmediatelyaftertherefrigeratoris unpacked.ChildrenshouldNEVERusetheseitemstoplay. Cartonscoveredwithrugs,bedspreads,plasticsheetsor stretchwrapmaybecomeairtightchambers,andcanquickly

causesuffocation. PROPERDISPOSALOFYOURREFRIGERATOROR

FREEZER

Risk of child entrapment

Child entrapment and suffocation are not problems of the past.

Junked or abandoned refrigerators or freezers are still

dangerous - even if they wilI sit for "just a few days." If you are getting rid of your old refrigerator or freezer, please follow the

instructions below to help prevent accidents.

ELECTRICAL INFORMATION ,, The refrigerator must be plugged into its own dedicated

115 Volt, 60 Nz,, AC onmy electric outlet. The power cord of the appliance is equipped with a three-prong grounding

plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three- prong receptacle. The receptacle must be installed in

accordance with local codes and ordinances. Consult a qualified electrician. Do not use an extension cord or

adapter p_ug.

,, If the power cord is damaged, it should be replaced by the

manufacturer, service technician or a qualified person to prevent any risk.

,, Never unplug the refrigerator by pulling on the power

cord. Always grip the plug firmly, and pulI straight out from the receptacle to prevent damaging the power cord.

,, Unplug the refrigerator before cleaning and before

replacing a light bulb to avoid electrical shock.

,, Performance may be affected if the voltage varies by'

10% or more. Operating the refrigerator with insufficient power can damage the compressor. Such damage is not covered under your warranty.

Do not plug the unit into an outlet controlled by a walI switch or pull cord to prevent the refrigerator from being

turned off accidentally.

Avoid connecting refrigerator to a Ground Fault Interruptor

(GFI) circuit.

Before you throw away your old refrigerator/freezer: o Remove doors.

_, Leave shelves in place so children may not easily climb

inside. ,, Have refrigerant removed by a qualified service

technician.

3=prorlg g_suaded P!ug

This Owner's Guide provides specific operating instructions for

your model. Use the refrigerator onIy as instructed in this Use &

Care Manuai. Before starting the refrigerator, follow these important first steps.

LOCATION

o Choose a ptace that is near a grounded electrical outleL

Do Not use an extension cord or an adapter plug.

o If possible, place the refrigerator out of direct sunlight

and away from the range, dishwasher or other heat

SOUrCeS,

. The refrigerator must be instaIIed on a floor that is level

and strong enough to support a fully loaded refrigerator.

. Consider water supply availability for models equipped

with an automatic ice maker.

INSTALLATION

Installation Clearances

. Allow the following clearances for ease of installation,

proper air circulation, and plumbing and electrical connections:

Sides & Top .................. 3/8"

Back ........................... 1"

DOOR OPENING

To Remove Toe Grille:

Open freezer and fresh food compartment doors.

Working from left side of toe grille, slip your fingers between top of toe grille and cabinet. Gently pull

forward until first set of tabs are free. Slide

your hand down past Cabinet the free tabs and pulI forward again until the

second set of tabs are free. Continue this Grille / _-_.,

process until all tabs . j_; are free and the toe __ _

grille can be removed. (See graphic at top of

-<<.

page in right column.)

LEVELING

Ali four corners of your refrigerator must rest firmly on asolid floor_

Your refrigerator is equipped with adiustabie front rollers to help level your unit. To ensure proper door seal and assist door closing, the refrigerator should be tilted 1/4" (6 ram), front to back.

ToLevel Your Refrigerator:

1. Remove toe grille, (See "To Remove Toe Gri//e',)

2. Use flat-blade screwdriver or 3/8" socket wrench to adjust front rollers.

Your refrigerator should be positioned to allow easy access to a counter when removing food. For best use of drawers and freezer baskets, the refrigerator should be in a position where both the refrigerator and freezer doors can be fully opened.

TOE GRILLE INSTALLATION/REMOVAL

Toinstall Toe Grille:

1. Open freezer and fresh food compartment doors.

2. Line up toe grille at base of refrigerator, making sure the four bottom tabs are resting through holes at base of

cabinet.

3. Starting from Ieft side of toe grille, press in on first top tab using your thumb and push toe grille forward until it snaps in place. Continue this process until al! tabs are snapped in place and toe grille is secured to refrigerator.

I Raise

i_iiiii

Check both doors to be sure seals touch cabinet on atl four sides.

To Connect Water Supply Line To lee Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply and flush suppty Iine until water is clear. Turn OFF water supply at shutoff valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line, as shown.

5. Push water supply Iine into water valve inlet as far as it will go (¼ inch). SIide ferruIe (sleeve) into valve inIet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water suppiy line to rear panel of refrigerator as shown.

7. Coil excess water suppIy line (about 2Y2 turns) behind refrigerator as shown and arrange coils so they do not

vibrate or wear against any other surface.

8. Turn ON water supply at shutoff vaIve and tighten any connections that leak.

9. Reconnect refrigerator to eIectricaI power source.

10. To turn ice maker on, Iower wire signal arm (side mounted) or set the ice maker's On/Off power switch to the "t" position. (rear mounted)

Before lnstafling The Water Supply Mne, You Will Need: ,, Basic Tools: adjustable wrench, flat-blade screwdriver,

and Phillips TM screwdriver

,, Access to a household cold water Iine with water pressure

between 30 and 100 psi.

,, A water supply line made of ¼ inch (6.4 ram) OD, copper

tubing. To determine the length of copper tubing needed,

you wilI need to measure the distance from the ice maker

inlet valve at the back of the refrigerator to your cold water pipe=Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown)=

,, A shutoff valve to connect the water supply Iine to your

household water system= DO NOT use a self-piercing type shutoff valve.

o A compression nut and ferrule (sleeve) for connecting the

water supply line to the ice maker inlet valve.

Plastic Water "tubing

to ice Make-

FIH Tube

'--- Copper water Jine

_ from household water su[ pl_ _de enough tubing _, Ioog to allow

}wng refrigerator out for cleaning.

Scl'ews j

TO DISCONNECT

1.Press outer ring against race

remove TUDe

oush until mark touches face of fitting

Tools Necessary:

Phillips head

DOOR REMOVAL INSTRUCTIONS:

If it is necessary to move the refrigerator through narrow doorways, follow these steps to remove the doors.

1. Disconnect electrical supply.

2. Open both doors, then remove toe grille.

3. Close doors.

To Remove Refrigerator Door:

1. Remove top hinge cover screw on refrigerator door and remove cover.

2. Trace around hinge with soft lead pencil. This will make it easier to realign doors when they are replaced.

3. Remove top hinge and lift refrigerator door off bottom hinge pin. Set door aside.

4. Remove bottom hinge, if necessary.

5. Reverse this procedure to reinstall refrigerator door.

To Remove Freezer Door:

1. Disconnect water line coming from ower hinge of freezer aoor at connection located under front of freezer: Press ouler nng against face of fitting, then pull to

remove tube.

2. Remove top h_nge cover screw on lreezer door and remove cover.

3. Disconnect wrong harness connector plug at tor_ htnge: D_aceyour thumbs on flat sides of each connector aria Dana both Earts eacK and forth, then with firm grasp, pull both pieces apart.

4. Trace around hinge wlth soft earl Pencil This wiI make _teas_er to realign doors wnen they are reDIaced.

5. Remove [co hinge allowing w_nng harness to DUllthrough hinge and lift freezer door off at bottom hinge Din Lay door dowr flat to avoid k_nking water line.

6. Remove bottom h_nge, if necessary.

7. Reverse this procedure to reinstall freezer door.

When Dam doors qave oeen reinstalled, connect water I_neby inserting tube and push until mark tOUCheSface of fitting, replace toe grille and ptug in electrical power

cord. Turn both temperature controls [o center position. Adjust settings as necessary.

Featuresmayvary

accordingtomodel

Freezer and Refrigerator

Ice Cream Shelf i

Controls

Spi[iproofT,, CAUT[ON:

j Aspect Shelf Do Not Remove

_ Water Fimter Compartment

Dairy

_ Magnet Behind

Fixed

Door Bin

Rce Container

SheR

Shelf

Tilt Out

Door Bin

SrnammBasket

Large

Glide Out

Basket

Tilt Out

Door Rirl

Large Basket

Tilt Out

Door Bin

. _"-_ Door Bin

j ........ Crisper Ran

-p_::)_:z;!_r::J_ ....................................................

\-- Toe Grille

Dairy

Compartment

SpiHProof TM

Sliding Shelf

Door Bin

Tam[Bottle

Retainer

Door Bin

Specta[ Rtem

Rack Meat Keeper

CaR RaCk

and Cover

Fixed Door Din

ALLOWING COOLINGTIME BEFORE USE To ensure reliable food storage, allow your refrigerator and freezer to operate with the doors closed for 8 to 12 hours before

placing food inside= During this cooling period, you do not need to adjust the controls, which are preset at the factory=

SETTING COOLING TEMPERATURES Your refrigerator comes with a state-of-the-art electronic digital control system= The system's control panel is located at the top of

the the fresh food compartmenL

The two digital displays on the left half of the control panel indicate the current settings or temperatures of your freezer and fresh food compartments= The models with a 2-digit temperature display are for reference only, and do not display the current accurate compartment temperature= Should you desire to see what the current accurate temperature is, place a separate thermometer

inside the freezer or fresh food compartment in the desired location=

(Temperature Display L Features may vary.)

Toadiustthetemperaturetoahigherorlowersetting,press theUp(Cold)orDown(Colder)buttonclosesttothedisplay. Thefirsttimeyoupressthebutton,thedisplayshowscurrent settingyouentered.Eachpressofthebuttonafterthat changesthesettingbyone.

Thedisplayshowsyournewsettingmomentarily,then changesbacktothecurrenttemperature.

MAKINGTEMPERATURE ADJUSTMENTS After running your refrigerator for 24 hours, you can adjust

temperatures as needed. Make your adjustments small and gradual, allowing time for temperatures to change and

stabilize. Refer to the following guidelines for temperature settings.

WHATTO DO IFTHETEMPERATURE DISPLAYS FLASH

If either display is continuously flashing, it may indicate that the

control system has detected a performance problem. Call your

EJectrolux service representative, who can interpret the

flashing message.

Numeric Display

CHOOSINGFAHRENHEITORCENTIGRADE Dependingonwhichtemperaturestandardyouprefertouse,

youcansetyourcontrolpaneltodisplayinfahrenheitor centigrade.Tochangebetweenfahrenheitandcentigrade, presstheModebutton(locatedbetweenthetwodigital temperaturedisplays).

F_,cz_7 TJ_mp Nr_f_ Fo_;d 7_mp

Press to alternate between Fahrenheit and Centigrade

Temperature Adjustment Guide

{fFresh Food €ompartrnent is too warm Adjust Fresh Food control one degree

Freezer

Temperature Display (2-Digit)

Freezer Fresh Food

F o C o F o C o

colder by pressing Down (Colder) button.

Fresh

Food

If Fresh Eo0d €0mpartment is toO C0]d Adjust Fresh Food control one degree

If FreeZer Compartment is too waim Adjust Freezer control one degree colder

If Freezer cOmpartment is toe c0{d Adjust Freezer control one degree warmer

warmer by pressing the Up (Cold} button.

by pressing Down (Colder) button.

by pressing the Up (Cold) button.

+ 18 hidden pages