Frigidaire FRS26R2AQ0, FRS26H5ASB0, FRS26F5AW1, FRS26F5AQ1, FRS26F5AB1 Owner’s Manual

...

........... 6 L_

......... 7_

perature Controls ....... 8

Espa_ol ........... 25

Fran;ais ........... 50

Looking Inside .......... 9- 11

Automatic Ice and Water

Dispenser ................ 12 - 15

Food Storage

& Energy Saving Tips ....... 16

Normal Operating Sounds,, 17

Care & Cleaning ......... 18 - 19

Warranty ...................... 20

Before You Call

Solutions to

Common Problems .............. 21 - 24

O 0

READ AND SAVE THESE INSTRUCTIONS PIN240389302(0107)

Congratulations on your purchase of a new refrigerator! We here at Electrolux Home Products are very proud of our

product and we are completely committed to providing you with the best service possible. Your satisfaction is our #1

priority. Please read this Use & Care Manual very carefully. Itcontains

valuable information on how to properly maintain your new refrigerator.

We know you'll enjoy your new refrigerator and Thank You for choosing our product. We hope you consider us for future purchases.

PLEASE READ AND SAVETHESEINSTRUCTIONS

This Use & Care Manual provides specific operating instructions for your model. Use your refrigerator only as

instructed in this manual. These instructions are not meant to cover every possible condition and situation that may

occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.

Questions?

1-800-944-9044

(United States)

1-866-213-9397

(Canada)

Extend Your Warranty Protection

With An

Extended Service Contract

CALL 1-800-944-9044

To Enjoy These Benefits:

Please record your model and serial numbers below for future reference, This information is found on the serial

plate located inside the refrigerator compartment,

Model Number: Serial Number:

Purchase Date:

Total freedom from repair bills so

unexpected repairs won't upset your budget.

Fast, convenient toll-free service is just

a phone call away. Top-quality repairs by factory-trained

experts.

Quick access to genuine replacement parts so you can rest assured your

refrigerator is repaired with the proper

components.

Please complete and mail in the Product Registration Card included with your refrigerator.

FORYOURSAFETY

• Donotstoreorusegasoline,orotherflammableliquids inthevicinityofthisoranyotherappliance.Read productlabelsforwarningsregardingflammabilityand

otherhazards.

• Donotoperatetherefrigeratorinthepresenceof explosivefumes.

• Avoidcontactwithanymovingpartsofautomaticice maker.

• Removeallstaplesfromthecarton.Staplescancause severecuts,andalsodestroyfinishesiftheycomein contactwithotherappliancesorfurniture.

CHILDSAFETY Destroyorrecyclethecarton,plasticbags,andanyexterior

wrappingmaterialimmediatelyaftertherefrigeratoris unpacked.ChildrenshouldNEVERusetheseitemstoplay. Cartonscoveredwithrugs,bedspreads,plasticsheetsor stretchwrapmaybecomeairtightchambers,andcanquickly

causesuffocation.

PROPER DISPOSAL OF YOUR REFRIGERATOR OR FREEZER

Risk of child entrapment

Child entrapment and suffocation are not problems of the past.

Junked orabandoned refrigerators or freezers are still dangerous - even if they will sit for "just a few days." If you are getting rid of your old refrigerator or freezer, please

follow the instructions below to help prevent accidents.

Before you throw away your old refrigerator/freezer:

• Remove doors.

• Leave shelves in place so children may not easily climb inside.

• Have refrigerant removed by a qualified service technician.

ELECTRICAL INFORMATION

• The refrigerator must be plugged into its own

dedicated 115 Volt, 60 Hz., AC only electric outlet.

The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. Itmust be plugged directly into a properly grounded three-prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician. Do not use an extension cord or adapter plug.

• Immediately repair or replace any power cord that becomes frayed or damaged.

• Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.

• Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock.

• Performance may be affected if the voltage varies by

10% or more. Operating the refrigerator with insufficient power can damage the compressor. Such damage is not covered under your warranty.

• Do not plug the unit into an outlet controlled by a wall switch or pull cord to prevent the refrigerator from being turned off accidentally.

• Avoid connecting refrigerator to aGround Fault Interruptor (GFI) circuit.

ThisOwner'sGuideprovidesspecificoperating instructionsforyourmodel.Usetherefrigeratoronlyas instructedinthisUse&CareManual.Beforestartingthe refrigerator,followtheseimportantfirststeps.

LOCATION

• Chooseaplacethatisnearagroundedelectricaloutlet. DoNotuseanextensioncordoranadapterplug.

• Ifpossible,placetherefrigeratoroutofdirectsunlight andawayfromtherange,dishwasherorotherheat

sources.

• Therefrigeratormustbeinstalledonafloorthatislevel andstrongenoughtosupportafullyloadedrefrigerator.

• Considerwatersupplyavailabilityformodelsequipped withanautomaticicemaker.

INSTALLATION

• Do Not installthe refrigeratorwhere the temperature willdrop below 55°F (13°C) or riseabove 110°F (43°C). The compressor will notbe able to maintain proper temperatures insidethe refrigerator.

Installation Clearances

• Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical

connections:

Sides & Top 3/8" Back 1"

DOOR OPENING

Your refrigerator should be positioned to allow easy access to a counter when removing food. For best use of drawers and freezer baskets, the refrigerator should be in a position where both the refrigerator and freezer doors can be fully opened.

TOE GRILLE INSTALLATION / REMOVAL

To Install Toe Grille:

1. Open freezer and fresh food

compartment doors.

2. Line up toe grille at

base of refrigerator, making sure the four

bottom tabs are

restingthrough holes at base of cabinet.

3. Starting from left side

oftoe grille, press in on first top tab using your thumb and pushtoe grilleforward untilitsnaps inplace. Continue

this process untilall tabs aresnapped in place and toe

grille issecured to refrigerator.

LEVELING

All four corners of your refrigerator must rest firmly on a solid floor. Your refrigerator is equipped with adjustable front rollers to help level your unit.

To Level Your Refrigerator:

1. Remove toe grille. (See "ToRemove Toe Grille"above.)

2. Use flat-blade screwdriver or 3/8" socket wrench

to adjust front rollers.

To Remove Toe Grille:

1. Open freezer and fresh food compartment doors.

2. Working from left side of toe grille, slip your fingers between top of toe grille and cabinet. Gently pull forward until first set of tabs are free. Slide your hand down past the free tabs and pull forward again until the second set of tabs are free. Continue this process until all tabs are free and the toe grille can be removed. (See graphic at top of page in right column.)

3. Check both doors to be sure seals touch cabinet on all four sides.

Before Installing The Water Supply Line, You Will Need

• Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver

• Access to a household cold water line with water pressure between 20 and 100 psi.

• A water supply line made of 1/_inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

• A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.

• A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shut

off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line, as shown.

5. Push water supply line into water valve inlet as far as it will go (1/_inch). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of refrigerator as shown.

7. Coil excess water supply line (about 2V2turns) behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that leak.

9. Reconnect refrigerator to electrical power source.

10. Toturn ice maker on, lower wire signal arm (see ice maker front cover for ON/OFF position of arm).

Tools Necessary:

Phillips" head

DOOR REMOVAL INSTRUCTIONS:

If it is necessary to move the refrigerator through narrow doorways, ....

follow these steps to remove the doors.

1. Disconnect electrical supply.

i!!i

2. Open both doors, then remove toe grille.

..... 3. Close doors.

To Remove Refrigerator Door:

1. Remove top hinge cover screw on refrigerator door and remove cover.

2. Trace around hinge with soft lead pencil. This will make iteasier to realign doors when they are replaced.

3. Remove top hinge and lift refrigerator door off bottom hinge pin. Set

door aside.

4. Remove bottom hinge, if necessary.

5. Reverse this procedure to reinstall refrigerator door.

To Remove Freezer Door:

1. Disconnect water line coming from lower hinge offreezer door at connection located under front offreezer: grip water tube firmly in one hand, then with

3/8"wrench or fingers, push in on gray collar to release water connector. ....

2. Remove top hinge cover screw on freezer door and remove cover.

3. Disconnect wiring harness connector plug at top hinge: place your thumbs on flat sides of each connector and bend both parts back and forth,

then with firm grasp, pull both pieces apart.

4. Trace around hinge with soft lead pencil. This will make iteasier to

realign doors when they are replaced.

5. Remove top hinge,allowingwiring hamess to pullthrough hinge andliftfreezer door off of bottom hinge pin. Lay door down flat to avoid kinking water line.

6. Remove bottom hinge, if necessary.

7. Reverse this procedure to reinstall freezer door.

When both doors have been reinstalled, replace toe grille and plug in electrical power cord. Turn both temperature controls to center position. Adjust settings as necessary.

Freezer and Refrigerator SpillSafe TM

Controls Shelf

Ice Cream

Door Bin

Ice Container

Pizza Shelf

Wire Shelf

Small Items

Door Bin

Wire Shelf

Door Bin

Small Basket

Large Basket

Door Bin

Ice

Water Filter

Dairy Door

Door Bin

Wine Rack

Door Bin Meat Keeper

and Cover SpillSafe'"

Fixed Shelf Door Bin

Egg Tray

Special Item

Rack

Tall Bottle

Retainer

--Snugger

Large Basket

Door Bin

Crisper Pan and Cover

Fixed Door Bin

Toe Grille

Features may vary according to model

COOL DOWN PERIOD

Toensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 to 12 hours before loading it with food.

REFRIGERATOR & FREEZER CONTROLS

TEMPERATURE ADJUSTMENT

• After 24 hours, adjust the controls as needed. Adjust

temperatures gradually: move the knob in small increments, allowing the temperature to stabilize.

• For colder temperatures, turn the knob towards Colder.

• For warmer temperatures, turnthe knob towards Warmer. To maintain temperatures, a fan circulates air in the

refrigerator and freezer compartments. For good circulation, do not block cold air vents with food items.

Refrigerator & Freezer Controls

TEMPERATURE ADJUSTMENT GUIDE

If Refrigerator Compartment Is Too Warm Turn Refrigerator Control Slightly Towards Colder.

If Refrigerator Compartment Is Too Cold Turn Refrigerator Control Slightly Towards Warmer.

If Freezer Compartment Is Too Warm Turn Freezer Control Slightly Towards Colder.

If Freezer Compartment Is Too Cold Turn Freezer Control Slightly Towards Warmer.

To Turn Refrigerator Off Turn Freezer Control To Off.

PIZZA SHELF (SOME MODELS)

This shelf is attached to the freezer wall beside the ice dispenser container. This convenient area allows for storage of pizza and other tall items placed vertically between the ice dispenser container and the freezer wall.

ICE CREAM SHELF (SOME MODELS)

This shelf attaches tothe top ofthe ice dispensercontainer. Itallowsstorage of both roundand rectangular cartons of your favorite ice cream.

TIP-UP SHELF (SOME MODELS) A Tip-Up shelf in the freezer section allows tall items to be easily stored.

CANTILEVER SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting the shelves, remove all food. Cantilever shelves are supported at

the back of the refrigerator.

To adjust cantilever shelves:

!O Liftfront edge up.

Pull shelf out.

Replace the shelf by inserting the hooks at rear of the shelf into the wall bracket. Lower the shelf into the desired slots and lock into position.

SpillSafe TM glass shelves (some models) catch and hold accidental spills. In

some models, the SpillSafe TM shelves slide out for easy access to food and forfast cleaning. The shelves slide out independently oftheir mounting brackets. Just pull the front of the shelf forward. Shelves can be extended as far as the

stopper will allow but are not removable from their mounting brackets.

Pizza Shelf

Ice Cream Shelf

Cantilever Glass Shelf

Cantilever Sliding Glass Shelf

DOOR STORAGE

Door bins and shelves are provided for convenient storage of jars, bottles, and cans. Frequently used items can be

quickly selected. Some models have door bins that can accommodate gallon-

sized plastic drink containers and economy-sized jars and containers. Some bins are adjustable for maximum storage capacity.

The dairy compartment, which is warmer than the general food storage section, is intended for short term storage of cheese, spreads, or butter.

ADJUSTABLE DOOR BINS Some models have adjustable door bins that can be moved

tosuit individual needs.

Tomove door bins

1. Lift bin straight up.

2. Remove bin.

3. Place bin in desired position.

4. Lower bin onto supports untillocked in place.

TALL BOTTLE RETAINER (SOME MODELS) The TallBottle Retainer keeps tall containers inthe bin from

falling forward when opening orclosingthe refrigeratordoor. To install, hold the retainer at the top, and slide it over the outside wall of the bin, as shown in the diagram. The Tall

Bottle Retainer works best with a BinSnugger.

Tall Bottle Retainer (left) and Bin Snugger (right)

SPECIAL ITEM RACK (SOME MODELS) The innovative design of the Special Item Rack allows you

to store a six-pack of 12 ounce drink cans, a bottle of wine, a two-liter soft drink bottle, or a carton of eggs. The Special

Item Rack mounts on the left side of your refrigerator. To

install, just slide the Special Item Rack onto any shelf as

shown inthe drawing.

Special ItemRack

CRISPERS (SOME MODELS) The crispers, located under the bottom refrigerator shelf,

are designed for storing fruits, vegetables, and other fresh produce.Wash itemsinclear water and removeexcess water before placingthem inthe crispers. Itemswith strong odors or high moisture content should be wrapped before storing.

iiii!!i¸!ili!ii!i!i iii:!i!i! iiiiiii!iii!i iil

Crisper Drawer

MEAT KEEPER (SOME MODELS) Some models are equipped with a Meat Keeper. Meat Keeper

temperatures can be adjusted by sliding the Meat Keeper TemperatureControl in eitherdirection. Use thispan for short

term storage of bulk meat items. If meats are to be kept longer than one or two days, they should be frozen. The Meat Keeper is fixed and cannot be moved up or down. If fruits or vegetables are to be stored in the Meat Keeper, set the Meat KeeperTemperature Control toa warmer setting to preventfreezing.

HUMIDITY CONTROL (SOME MODELS) The Humidity Control, present on some models with crisper

drawers, allowsyou to adjust the humiditywithinthe crisper. This can extend the life of fresh vegetables that keep best in high humidity.

Crisper Humidity Control

DELl DRAWER (SOME MODELS)

Some models are equipped with a Deli Drawer for storage of luncheon meats, spreads, cheeses, and other deli items.

Meat Keeper with Temperature Control

WINE RACK (SOME MODELS) The wine rack stores bottles ofwine, or single two-literplastic

bottles ofjuice or soda pop. To install, slide the Wine Rack ontothe shelf with the curve facing in. To remove, slide the

Wine Rack out. Install on either side of shelf.

Wine Rack

ICE AND WATER DISPENSER FEATURES

The ice and water dispenser conveniently dispenses chilled water, and ice

cubes or crushed ice, depending on the model. Some models have an Extra Ice feature that increases ice production for special occasions such as parties.

Tooperate the ice dispenser, select the ice option desired using thetouchpad.

Press a glass against the dispensing paddle as far up as possible to catch all ice. To stop dispensing ice, pull glass away from dispensing paddle. Do not remove the glass until the ice has completely dispensed. (Complete instructions for the dispenser operation are attached to the inside of the freezer door.)

Tooperate the water dispenser, press a glass against the dispensing paddle. To stop dispensing water, pull glass away from dispensing paddle. A drip tray located at the base of the dispenser, catches small spills and allows them to evaporate. This drip tray is removable and dishwasher safe. Do not pour water or excess cubes into this area because there is no drain.

Dispenser Light (some models)

The dispenser has a lightwhichcan be turnedon and offby pressingthe Light touchpad. The light also turns on automatically when ice and/or water is dispensed. Replace lightbulb with an appliance bulb ofthesame wattage.

E_ ice Cube Crush Light FilterSialus

Ice and Water Dispenser Panel (features may vary according to model)

HOW the Water Dispenser Works

The water tank, located behind the drawers in the refrigerator compartment, automatically fills as water is dispensed. For proper dispenser operation, the recommended supply water pressure should fall between 20 psi and 100 psi.

After the refrigerator is connected to the water supply, fill the water tank by drawing one glass of water. It may take about 11/2minutes after activating the dispenser paddle before water begins to fill this first glass. Continue flushing the system for 3 minutes to rid the tank and plumbing connections of any impurities. The water dispenser has a built in shutoff device that will stop the water flow after 3 minutes of continuous use. Simply release the dispenser paddle to reset the shutoff

mechanism.

How the Ice Dispenser Works

The ice maker and container are located in the top of the freezer compartment. After the refrigerator is installed properly and has cooled for several hours, the ice maker can begin making ice within 24 hours. Air in new plumbing lines may cause the ice maker to cycle two or three times before making a full tray of ice. To begin ice production, lower the wire signal arm to the "down" or ON position. With no usage it will take approximately 2 days to fill the ice container. The ice maker turns off automatically when the ice container becomes full. To stop the ice maker, lift the wire signal arm until it clicks, and locks in the "up" or OFF position.

Because of new plumbing connections, the first production of ice cubes may be discolored or have an odd flavor. These

should be discarded until the cubes made are free of discoloration and taste.

ICEDISPENSERTIPS

• Icecubesstoredtoolongmaydevelopanoddflavor.Emptytheicecontainerandensurethatthewiresignalarmis inits"down"orONposition.Theicemakerwillthenproducemoreice.

• Occasionallyshaketheicecontainertokeepiceseparated.

• Keepthewiresignalarminits"up"orOFFpositionuntiltherefrigeratorisconnectedtothewatersupplyorwheneverthe watersupplyisturnedoff.

If a large quantity of ice is needed at one time, it is best to remove cubes directly from the ice container. The following sounds are normal when the ice maker is operating:

• Motor running

• Ice loosening from tray

• Ice dropping into ice container

• Running water

• Water valve opening or closing Stop the ice maker when cleaning the freezer and during vacations. If the ice maker will be turned off for a long period of time, turn the water supply valve to the closed position.

CLEANING THE ICE DISPENSER

Donotusethe icechuteasa handlewhen removingorreplacing theicestoragebin.

Surfaces there may be sharp.

Donot putfingersup icechute.Surfaces

there may be sharp.

Clean the dispenser and ice container at regular intervals, particularly before you take a vacation or move, or if the ice dispenser sticks.

1. Stop ice production by liftingthe wire signal arm to the "up" or OFF

position.

2. Remove icecontainer by liftingup and out. Empty and carefullyclean the container with mild detergent. Rinse with clear water. Do not use harshorabrasive cleaners.Allow ice containerto dry completelybefore replacing in the freezer.

3. Remove ice chips and clean the shelf and chute that supports the ice container.

4. Replace the ice container. Lower the wire signal arm on the ice maker to the "down" or ON position and the ice maker willresume

production.

Remove and empty the ice storage bin if:

1. An extended power failure (one hour or longer) causes ice cubes in the ice storage bin to melt and freeze together and jam the dispenser

mechanism.

2. The ice dispenser is not used frequently. Ice cubes will freeze together in the bin and jam the dispenser mechanism. Remove the ice storage

bin and shake to loosen the cubes.

NEVER use an ice pick or similar sharp instrument to break up the ice. This could damage the ice storage bin and dispenser mechanism.

PureSource TMIce and Water Filter (some models)

NOTE: If you purchased a refrigerator with a PureSource TMIce and Water filter, please read the following use and care information. This ice and water filter system filters water to your ice maker and water dispenser. It islocated in the upper rightback corner of the fresh food compartment.

System Startup:

Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter. The filter cartridge has already been installed in the filter housing at the factory. Refer to the How The Water Dispenser Works section

to properly fill the system with water. Changing the Filter:

Water conditions vary throughout the world, but changing the water filter every 6 - 9 months normally will ensure the highest possible water quality. The Filter

Status light will turn red after 400 gallons of water has flowed through the ice and

water dispenser (some models). Also, if the filter has been in a refrigerator that

has not been in use for awhile (during moving for example), change the filter before reinstalling the refrigerator. The dispenser system will also operate without

filtration (with filter cartridge removed).

To change filter:

It is not necessary to turn the water supply off to change the filter.

1. Open freezer door and leave open until filter change is complete.

2. Set ice maker wire signal arm to the OFF (up) position (See illustration on page 12).

3. Hold filter cup firmly, and unscrew towards left (Some water could leak out as you remove cup. This is normal.). Filter cartridge should come

down with cup. If cartridge remains in housing, pull down gently, while twisting filter back and forth.

4. Rinse out cup under running water.

5. The large o-ring that seals the filter system sets in the o-ring groove

down inside the cup. Should the o-ring fall out during filter cartridge

Order new filter cartridges through the dealer where you bought the refrigerator,

or contact the Consumer Assistance Center at 1-800-944-9044. It might be good to order some filter cartridges when you first install your refrigerator. Be sure

to ask for the RG-100 PureSource TM replacement cartridge.

The PureSource TM NGRG-

2000 Ice and Water Filter System with the RG-100

cartridge is tested and certified by NSF International,

the nationally recognized and respected,

not for profit, certification organization for public health safety. The PureSource TM system is tested and certified to ANSI/NSF

Standard 42. See performance data sheet

for specifications. This system should not

be used on water that is microbiologically unsafe or with water of unknown quality

unless the water has been adequately disinfected before or after traveling through

the filtration system.

• Rated Capacity - 400 gallons

• Rated service flow - .5 GPM

• Maximum Rated Pressure- 100 PSI

• Maximum Operating Temp. - 100 ° F

replacement, simply place it back in the groove prior to screwing the cup back in place. If the o-ring becomes damaged, you will need to order one

from the Consumer Assistance Center.

6. Discard old filter cartridge.

7. Remove new filter cartridge from packaging and place in cup. The end

with the small o-ring should be up, out of the cup.

8. Screw cup, with filter, back onto housing. Do Not Use Wrench To Reinstall Cup. Filter cartridge will self-align as cup is tightened. Be sure cup is

completely tightened with PureSource TM logo facing outward. Do Not Tighten Past Stop.

9. Set ice maker wire signal arm to the ON (down) position.

10. Check for leaks. Open refrigerator door. Wipe any water droplets from the filter cup. Fill a glass with water. If there is a leak, unscrew filter cup, and

reinsert the filter cartridge. Check placement of large O-ring. Reinstall

filter cup, making certain it is tightened completely.

11. To condition filter system and purge air from water line, fill a glass with water. Continue flushing the system for 30 seconds to assure that the

purest water possible is stored in water tank.

PureSource2 TM Ice and Water Front Filter (some models)

NOTE: Ifyou purchased a refrigerator with a PureSource2 TM Ice and Water front filter, please read the following use and care information. This ice and water filter system filters water to your ice maker and water dispenser. It islocated in the upper rightfront corner ofthe fresh food compartment.

System Startup:

Works section to properly fill the system with water.

Changing the Filter:

Water conditions vary throughoutthe world, but changing the water filter every 6 - 9 months normally will ensure the highest possible water quality. The Filter Status light will turn red after approximately 400 gallons of water has flowed through the ice and water dispenser. Also, if the filter has been in a refrigerator that has not been in use for awhile (during moving for example), change the filter before reinstalling the refrigerator. The dispenser system will also operate without filtration (with filter cartridge removed and bypass installed).

To change filter:

It is not necessary to turn the water supply off to change the filter.

Set ice maker wire signal arm to the OFF (up) position (See illustration on page 12).

Push the Filter Release Button, located to the right of the filter cartridge, to release the filter from the housing. To minimize the possibility of the filter falling out of the housing during removal, it would be best to hold the

Order new filter cartridges through the dealer where you bought the refrigerator,

or contact the Consumer Assistance

Center at 1-800-944-9044. It might be

good to order some filter cartridges when you first install your refrigerator. Be sure

to ask for the PureSource2 TM replacement cartridge.

filter as it moves out toward you.

3. Pull the old filter cartridge straight out of the housing.

4. Discard the old filter.

5. Remove the new filter cartridge from the packaging and insert into the

The PureSource2 TM Ice and Water Filter System NGFC

2000 with the PureSource2 TM cartridge FC 100 is tested and

certified by NSF International,

the nationally recognized and respected,

not for profit, certification organization for public health safety. The PureSource2 TM

Filter system is tested and certified to ANSI/ NSF Standards 42 and 53. See

performance data sheet for specifications.

This system should not be used on water that is microbiologically unsafe or with water

of unknown quality unless the water has

been adequately disinfected before or after

traveling through the filtration system.

• Rated Capacity - 400 gallons

• Rated service flow - .5 GPM

• Maximum Rated Pressure- 100 PSI

• Maximum Operating Temp. - 100° F

filter housing the same way the old one came out.

6. When the cartridge isalmost in,you willfeel itstop against the clip assembly

in the back of the housing. The clip assembly holds the filter cartridge firmly in place. At this point, you will need to push firmly until the cartridge snaps fully in place. When completely in place, the front of the filter cartridge

will be flush with the front of the housing.

7. Set the ice maker wire signal arm to the ON (down) position.

8. Fill a glass with water. As you are doing this, check for leaks at the filter

housing. There will be noticable spurts and sputters as the system pushes the air out through the system and out the dispenser nozzle. This is normal.

9. After you have run one glass of water, continue to flush the system for

approximately 3 minutes to assure that the purest water possible is stored in the water storage tank.

FOOD STORAGE IDEAS

Fresh Food Storage

• The fresh food compartment should be kept between 34° F and 40° F with an optimum temperature of 37° F.

• Avoid overcrowding the refrigerator shelves. This reduces the circulation of air around the food and results in uneven cooling.

Fruits and Vegetables

• Storage in the crisper drawers traps moisture to help preserve the fruit and vegetable quality for longer time periods.

Meat

• Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or surfaces does not occur.

Frozen Food Storage

• The freezer compartment should be kept at 0° F or lower.

• A freezer operates most efficiently when it is at least 2/3 full.

Packaging Foods for Freezing

• Tominimize dehydration and quality deterioration, use aluminum foil, freezer wrap, freezer bags or airtight containers. Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out, change color, and develop an off-flavor (freezer burn).

• Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.

• Do not refreeze meat that has completely thawed.

Loading the Freezer

• Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing, and can raise the temperature of frozen foods.

• Leave a space between the packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.

• Avoid storing hard-to-freeze foods such as ice cream and orange juice on the freezer door shelves. These foods are best stored in the freezer interior where the temperature varies less.

ENERGY SAVING IDEAS

• Locate the refrigerator in the coolest part ofthe room, out of direct sunlight, and away from heating ducts or registers. Do not place the refrigerator

next to heat-producing appliances such as a range, oven, or dishwasher. If this is not possible, a section of cabinetry or an added layer of insulation

between the two appliances will help the refrigerator operate more efficiently.

• Level the refrigerator so that the doors close tightly.

• Refer to this Use & Care Manual for the suggested temperature control settings.

• Periodic cleaning of the condenser will help the refrigerator run more efficiently. See the Care and Cleaning Chart on page 17.

• Do not overcrowd the refrigerator or block cold air vents. Doing so causes the refrigerator to run longer and use more energy.

• Cover foods and wipe containers dry before placing them in the refrigerator. This cuts down on moisture build-up inside the unit.

• Organize the refrigerator to reduce door openings. Remove as many items as needed at one time and close the door as soon as possible.

UNDERSTANDING THE SOUNDS YOU MAY HEAR

Your new high-efficiency refrigerator may make unfamiliar sounds. Don't be alarmed, these are all normal sounds. Hard

surfaces, such as vinyl or wood floors, walls, and kitchen cabinets may make sounds more noticeable. Listed below are descriptions of some of the most common sounds you

may hear, and what is causing them.

A. Evaporator

The flow of refrigerant through the evaporator may

create a boiling or gurgling sound.

B. Evaporator Fan

You may hear air being forced through the refrigerator by the evaporator fan.

C. Defrost Heater

During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After defrosting, a popping sound may occur.

D. Automatic Ice Maker

If your refrigerator is equipped with an automatic ice maker, you will hear ice cubes falling into the ice bin.

E. Cold Control & Defrost Timer

These parts can produce a snapping or clicking sound when turning the refrigerator on and off. The timer also produces sounds similar to an electric clock.

F. Condenser Fan

You may hearair being forced through the condenser by the condenser fan.

i i i

G. Compressor

Modern, high-efficiencycompressors operate much faster than older models. The compressor may have a high-pitched hum or pulsating sound.

H. Water Valve

Ifyour refrigerator isequipped with an automatic ice maker, you will hear a buzzing sound as the water valve opens to fill the ice maker during each cycle.

I. Drain Pan

You may hear water runningintothe drain pan during the defrost cycle.

J. Condenser

Keepyourrefrigeratorandfreezercleantopreventodorbuild-up.Wipeupanyspillsimmediatelyandcleanbothsectionsat leasttwiceayear.Neverusemetallicscouringpads,brushes,abrasivecleanersorstrongalkalinesolutionsonany surface.Donotwashanyremovablepartsinadishwasher.Always unplug the electrical power cord from the wall

outlet before cleaning.

Care & Cleaning Chart

Part Cleaning Agents Tips and Precautions

Interior/Door • Soap and water Use 2 tablespoons of baking soda in 1 quart of warm water. Be Liner • Baking soda and sure to wring excess water out of sponge or cloth before

water cleaning around controls, light bulb or any electrical part. Door Gaskets • Soap and water Wipe gaskets with a clean soft cloth. Drawers/Bins • Soap and water Do not wash any removable items (bins, drawers, etc.) in

dishwasher.

Glass • Soap and water Allow glass to warm to room temperature before immersing in Shelves • Glass cleaner warm water.

• Mild liquid sprays

Toe Grille • Soap and water Vacuum dust from front of toe grille. Remove toe grille (See

• Mild liquid sprays illustration on page 5). Vacuum backside and wipe with sudsy

• Vacuum attachment cloth or sponge. Rinse and dry.

Exterior and Handles

(Stainless

Steel Models Only)

Condenser • Vacuum attachment Use the dusting tool attachment on your vacuum to remove dust

Coils build-up on the condenser coils (see item "J" in illustration on page

• Soap and water

• Ammonia

• Stainless Steel Cleaners

Do not use commercial household cleaners, ammonia, or alcohol

to clean handles. Clean stainless steel front and handles with non-abrasive soapy

water and a dishcloth. Rinse with clean water and a soft cloth. Wipe stubborn spots with an ammonia-soaked paper towel, and

rinse. Use a non-abrasive stainless steel cleaner. These cleaners can be purchased at most home improvement or major department stores. Always follow manufacturer's instruction.

NOTE: Always, clean, wipe and dry with the grain to prevent cross-grain scratching. Wash the rest of the cabinet with warm water and mild liquid detergent. Rinse well, and wipe dry with a

clean soft cloth.

17 for location).

REPLACING LIGHT BULBS

1. Unplug refrigerator.

2. Wear gloves as protection against possible broken glass.

3. Remove light cover, if necessary.

4. Unscrew and replace old bulb with an appliance bulb of the same wattage.

5. Replace light cover, if necessary.

6. Remember to plug the refrigerator back in.

Refrigerator Light Replacement

Crisper Light Replacement (Some Models)

Vacation and Moving Tips

Short

Vacations

Long

Vacations

Moving

Leave refrigerator operating during vacations of 3 weeks or less. Use all perishable items from refrigerator compartment.

Turn automatic ice maker off, even if you will only be gone for a few days.

Remove all food and ice if you will be gone one month or more.

Turn controls to OFF and disconnect power. Turn off automatic ice maker and turn water supply valve to closed position.

Clean interior thoroughly. Leave both doors open to prevent odors and mold build-up. Block doors open if necessary.

• Remove all food and ice.

• If using handcart, load from side.

• Adjust rollers all the way up to protect them during sliding or moving.

• Pad cabinet to avoid scratching surface.

Freezer Light Replacement

REFRIGERATOR WARRANTY

Your refrigerator is protected by this warranty

WARRANTY

PERIOD

FULL ONE-YEAR

WARRANTY

LIMITED 2"D-5TM

YEAR WARRANTY

(Cabinet Liner and Sealed System)

LIMITED

WARRANTY

(Applicable to the State of Alaska)

One year from original purchase date

Second through fifth years from original purchase date

Time periods listed above.

In the U.S.A., your appliance is warranted by Electrolux Home Products North America, a division of White Consolidated Industries Inc. We authorize no person to change or add to any of our obligations under this warranty. Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux Home Products North America servicer. In Canada, your appliance is warranted by WCI Canada Inc.

THROUGH OUR AUTHORIZED SERVICERS,

Pay all costs for repairing or replacing any parts of this appliance which prove to be defective in materials or workmanship. Excludes original and replacement Ice & Water filter cartridges (if equipped). Original and

replacement cartridges are warranted for 30 days (parts only).

Repair or replace any parts in the cabinet liner or Sealed Refrigeration System (compressor, condenser, evaporator, drier and tubing) which prove to be

defective in materials or workmanship.

All of the provisions of the full warranties above and the exclusions listed below apply.

WE WILL:

THE CONSUMER WILL BE RESPONSIBLE FOR:

Costs of service calls that are listed under NORMAL RESPONSIBILITIES OF THE CONSUMER. *

Costs for pick up and delivery of the appliance required because of service. Costs for labor, parts and transportation other than with respect to the cabinet liner or Sealed Refrigeration System.

Costs of the technician's travel to the home and any costs for pick up and delivery of the appliance required because of

service.

*NORMAL RESPONSIBILITIES

OF THE CONSUMER

This warranty applies only to products in ordinary household use, and the consumer is responsible for the

items listed below:

1. Proper use of the appliance in accordance with instructions provided with the product.

2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance with all local plumbing, electrical and/or gas codes.

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house wiring.

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,etc., which are not a part of the appliance when it was shipped from the factory.

5. Damages to finish after installation.

6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).

EXCLUSIONS

This warranty does not cover the following:

1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.

NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.

2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary household use. The consumer shall pay for such service calls.

3. Damages caused by services performed by servicers other than Electrolux Home Products North America or its authorized servicers; use of parts other than genuine Electrolux Home Products parts; obtained from persons

other than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

IF YOU NEED SERVICE

Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all

receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this warranty must be obtained by contacting Electrolux Home Products:

This warranty only applies in the 50 states of the U.S.A., Puerto Rico, and Canada. Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by Electrolux Home Products North America, a division of White Consolidated

Industries Inc. In Canada, your appliance is warranted by WCI Canada Inc.

01-U-RE-02 (Rev. 12/2000)

USA

800,,944,,9044

Electrolux Home Products North America P.O. Box 212378

Augusta, GA 30917

Canada

866o213o9397

Electrolux Home Products North America

6150 McLaughlin Road

Mississauga, Ontario

L5R 4C2

PROBLEM _ CAUSE CORRECTION

RUNNING OF REFRIGERATOR

Compressor does not run.

Refrigerator runs too much or too long.

Compressor goes off and • Thermostat keeps the • This is normal. Refrigerator goes on and off to keep

on frequently, refrigerator at a constant temperature constant.

TEMPERA TURES ARE TOO COLD

• Freezer control is OFF.

• Refrigerator is in defrost cycle.

Plug at wall outlet is

disconnected.

House fuse blown or tripped

circuit breaker.

Power outage. Room or outside weather is

hot. Refrigerator has recently been

disconnected for a period of time.

Automatic ice maker is operating.

Doors are opened too

frequently or too long.

Refrigerator/freezer door may be slightly open.

Freezer control is set too cold (control found in refrigerator

section).

Refrigerator/freezer gasket is

dirty, worn, cracked, or poorly fitted.

Condenser is dirty.

temperature.

• Set freezer control. See Temperature Controls section.

• This is normal for a fully automatic defrost refrigerator. The defrost cycle occurs periodically, lasting about 30

minutes.

• Ensure plug is tightly pushed into outlet.

Check/replace fuse with a 15 amp time-delay fuse. Reset circuit breaker.

Check house lights. Call local Electric Company. It's normal for the refrigerator to work longer under

these conditions.

It takes 8-12 hours for the refrigerator to cool down completely.

• Ice maker operation causes refrigerator to run slightly

more.

• Warm air entering the refrigerator causes it to run

more. Open doors less often.

• Ensure refrigerator is level. Keep food and containers from blocking door. See PROBLEM section

OPENING/CLOSING OF DOORS/DRAWERS.

• Set refrigerator controlto warmer setting until

refrigerator temperature is satisfactory. Allow 24 hours

for temperature to stabilize.

• Clean or change gasket. Leaks in door seal will cause

refrigerator to run longer in order to maintain desired

temperatures.

Clean condenser. See Care & C/eaning Chart in Care and Cleaning section.

Freezer temperature too • Freezer control is set too cold. • Set freezer control to a warmer setting. Allow 24 hours

cold. Refrigerator for temperature to stabilize. temperature is satisfactory.

Refrigerator temperature • Refrigerator control is set too • Set refrigerator control to a warmer setting. Allow 24 too cold. Freezer cold. hours for temperature to stabilize. temperature is satisfactory.

Food stored in drawers • Refrigerator control is set too • See solution above. freezes, cold.

Food stored in Meat Keeper freezes (some

models).

• Meat Keeper Temperature Control set too cold.

Adjust Meat Keeper Temperature Control to a lower setting. (Meat should be stored at a temperature just below the freezing point for maximum fresh storage

time. It is normal for ice crystals to form due to the

moisture content of meat.)

PROBLEM | CAUSE CORRECTION

TEMPERA TURES ARE TOO WARM

Freezer/Refrigerator

temperature is too warm.

Freezer temperature is too • Freezer control is set too • Set freezer control to a colder setting. Allow 24 hours

warm, Refrigerator warm. for temperature to stabilize.

temperature is satisfactory.

Refrigerator temperature is • Refrigerator control is set too • Set refrigerator control to a colder setting. Allow 24

too warm, Freezer warm. hours for temperature to stabilize. temperature is satisfactory,

Temperature in the Meat • Meat Keeper Temperature • Adjust Meat Keeper Temperature Control to a colder

Keeper is too warm (some Control is set too warm. setting. models).

WA TERIMOIS TUREIFROS T INSIDE REFRIGERATOR

Moisture collects on inside of refrigerator walls.

Water collects on bottom • Vegetables contain and give • It is not unusual to have moisture on the bottom side of

side of drawer cover, off moisture, the cover.

Water collects in bottom of • Washed vegetables and fruit • Dry items before putting them in the drawer. Water

drawer, drain while in the drawer, collecting in bottom of drawer is normal.

WA TERIMOISTUREIFROS T OUTSIDE REFRIGERATOR

Moisture collects on outside of refrigerator or

between doors.

Doors are opened too

frequently or too long.

Door is slightly open.

Condenser is dirty.

• Weather is hot and humid.

• Door is slightly open.

• Door is opened too often or too long.

Open containers.

• • Keep containers covered.

• Weather is humid.

• Door is slightly open, causing cold air from inside refrigerator

to meet warm air from outside.

• Warm air enters the refrigerator whenever the door is opened. Open the door less often.

• See PROBLEM section OPENING/CLOSING OF

DOORS/DRAWERS.

• Clean condenser. See Care & C/eaning Chart in Care and Cleaning section.

• The rate of frost buildup and internal sweating increases.

• See PROBLEM section OPENING/CLOSING OF

DOORS/DRAWERS.

• Open door less often.

• Move humidity control (some models) to lower setting.

• This is normal in humid weather. When humidity is lower, the moisture should disappear.

• See PROBLEM section OPENING/CLOSING OF

DOORS/DRAWERS.

AUTOMATIC ICE MAKER

Ice maker is not making any ice.

• Ice maker wire signal arm is in the "up" or OFF position.

• Household water line valve is not open.

• Freezer is not cold enough.

Saddle valve on cold water pipe is clogged or restricted by

foreign material. Check to see if the water

dispenser is dispensing water.

Move wire signal arm to the "down" or ON position.

Turn on household water line valve.

• See PROBLEM section TEMPERATURES ARE TOO WARM.

• Turn off household water line valve. Remove valve. Ensure that valve is not a self-piercing saddle valve.

Clean valve. Replace valve if necessary.

• If not, the ice & water filter cartridge isclogged or restricted by foreign material, and must be replaced.

PROBLEM CAUSE CORRECTION

A UTOMA TIC ICE MAKER (CONTINUED)

Ice maker is not making • Ice maker is producing less ice enough ice. than you expect.

Freezer is not cold enough.

Household water line valve is not completely open.

Check to see if water dispenser is dispensing slower

than normal.

Ice maker should produce approximately 4 - 5 pounds of ice every 24 hours. Extra Ice should produce up to 8

pounds of ice every 24 hours. See PROBLEM section TEMPERATURES ARE TOO

WARM. Turn on household water linevalve.

If it is, replace the ice & water filter cartridge.

Ice maker will not stop making ice,

Ice maker is not separating the ice cubes.

Ice has bad odor and taste.

ICE DISPENSER

Dispenser will not dispense ice.

Ice dispenser is jammed.

Ice maker wire signal arm is

being held down by some item in the freezer.

• Ice cubes are not being used frequently enough.

• Ice cubes are hollow or smaller than normal.

• Ice has picked up odor or flavor from strong food stored

in refrigerator or freezer.

• Water running to ice maker has poor taste or odor.

• Ice not used frequently enough.

• Ice storage container is empty.

• Freezer temperature is set too warm.

Household water line valve is not open.

Freezer door is not closed. Ice dispensing arm has been

held in for more than 4-5 minutes.

• Ice has melted and frozen around auger due to infrequent

use, temperature fluctuations, and/or power outages.

• Ice cubes are jammed between ice maker and back

of ice container.

Ice cubes are frozen together.

Ice cubes are hollow or smaller

than normal.

Move item and release wire signal arm. Remove any ice cubes that are frozen together over the wire signal arm.

Remove and shake ice container to separate cubes.

The ice & water filter cartridge may be clogged. Replace filter cartridge.

Cover foods tightly. Discard stale ice. Ice maker will produce fresh supply.

• Add filter to water supply line. Consult a water purifying company.

• Discard stale ice.

• When the first supply of ice is dropped into the container, the dispenser should operate.

• Turn freezer control to a higher setting so that ice cubes will be made. When first supply of ice is made,

dispenser should operate.

• Open household water line valve. Allow sufficient time for the ice to be made. When ice is made, the

dispenser should operate.

• Ensure freezer door is closed.

• Motor is overloaded. Motor overload protector will reset in approximately 3 minutes. Ice can then be

dispensed. Remove ice container, thaw, and empty the contents.

Clean container, wipe dry, and replace in proper position. When new ice is made, dispenser should

operate.

Remove ice cubes that are jamming the dispenser.

Use the dispenser often so that cubes do not freeze together.

The ice & water filter cartridge could be clogged. Replace the filter cartridge. Dispensing system

operates best at 20 - 100 psi water pressure. Well water pressures should fall within this range.

+ 52 hidden pages