Frigidaire PLEFMZ99GCE, PLEFMZ99GCD, LEEFM389FEF, GLEFM97GPBB, PLEFMZ99GCB Owner’s Manual

!;i!¸......... 5

)ntrols ......... 7=12

Cooking ........................... 13

Control Pad Features ................... 14

Setting Oven Controls ............ 15=28

Bake=n=Warm TM Double Oven 29=31

Self Cleaning ........................... 32=34

Adjusting Oven Temperature. 34=35

General Care & Cleaning ....... 35=38

Before You Call

Solutions to Common Problems ........................ 39

Warranty ......................... Back Page

READ AND SAVE THESE INSTRUCTIONS pin 316417039 Rev C (0710)

Welcome& Congratulations

* * " ! ..... , * * o

,, ,, ,,

, i

i ,

Serial plate location

Open Bake-n-Warm TM Double
Oven orWarmer Drawer.

Congratulations on your purchase of a new range! At Electrolux Home Products,
we are very proud of our product and are completely committed to providing you
with the best service possible. Your satisfaction is our number one priority.

We know you'll enjoy your new range and Thank You for choosing our product.
We hope you consider us for future purchases.

PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS
This Use & Care Manual provides specific operating instructionsfor your model.

Use your range only as instructed in this manual. These instructions are not
meant to cover every possible condition and situation that may occur. Common
sense and caution must be practiced when installing,operating and maintaining
any appliance.

Please record your model and serial numbers below for future reference.

Model Number:
Serial Number:

Purchase Date:

This Use & Care Manual contains general operating instructions for your range
and feature information for several models. Your range may not have all the
described features. The graphics shown are representational. The graphics on
your range may not look exactly like those shown.

Product Registration

Register Your Product

The self-addressed PRODUCT REGISTRATION CARD should be filled in
completely, signed and returned to Electrolux Home Products.

© 2007 Electrolux Home Products, Inc.

All rights reserved.

Important Safety Instructions

Read all instructions before using this appliance. Save these instructions for future reference.

This manual contains importantsafetysymbols and instructions. Please payattention to these symbols and follow all instructions gwen.

This symbol will help alert you to situations that may cause serious bodily harm, death or property damage.

This symbol will help alert you to situations that may cause bodily injury or property damage.

• Remove all tape and packaging before using the range.
Destroy the carton and plastic bags after unpacking the

range. Never allow children to play with packaging material.

Proper Installation--Be sure your appliance is properly
installed and grounded by a qualified technician in

accordance with the National Electrical Code ANSI/
NFPA No. 70 latest edition and local electrical code

requirements. Installonly perinstallationinstructionsprovided
in the literature package for this range.

Ask your dealer to recommend a qualified technician and an
authorized repair service. Know how todisconnect the power

to the range at the circuit breaker or fuse box in case of an
emergency.

• User servicing--Do not repair or replace any part of the
appliance unless specifically recommended in the

manuals. All other servicing should be done only by a
qualified technician. This may reduce the risk of personal

injuryand damage to the range.

• Never modify or alter the construction of a range by
removing leveling legs, panels, wire covers, anti=tip

brackets/screws, or any other part of the product.

• All ranges can tip.

• injury to persons could result.

= Install anti=tip device packed with range.
. See installation Instructions.

tipping, the rangemust be secured by

properly installed anti=tip bracket provided

_ To reduce the risk of

with the range. To check if the bracket is

installed properly, visually check that rear
leveling leg is inserted into and fully

secured by the anti=tip bracket by removinc

lower panel or storage drawer. For models

with a Warmer Drawer or Bake-n-Warm TM

Double Oven, grasp the top rear edge of

the range and carefully attempt to tilt it
forward. Refer to the installation

instructions for proper anti=tip bracket

Stepping, leaning or sitting on the doors or

drawers of this range can result in serious injuries and
also cause damage to the range. Do not allow children to
climb or play around the range. The weight ofa child onan open
door may cause the range to tip, resulting in serious burns or
other injury.

Do not store items of interest to children in

the cabinets above a range or on the backguard of a
range. Children climbing on the range to reach itemscould be
seriously injured.

Do not use the oven or Warmer Drawer/

Bake=n=Warm TM Double Oven (if equipped) for storage.

Never Use Your Appliance for Warming or

Heating the Room.

• Storage in or on Appliance--Flammable materials
should not be stored in an oven, Warmer Drawer/Bake=
n-Warm TM Double Oven, near surface units or in the
storage drawer. This includes paper, plastic and cloth
items, such as cookbooks, plasticware and towels, aswell as

flammable liquids. Do not store explosives, such as aerosol

cans, on or near the range.

• Do Not Leave Children Alone--Children should not be
left alone or unattended in the area where appliance is

in use. They should never be allowed to sit or stand on any

part of the appliance.

• DO NOTTOUCH SURFACE UNITS, AREAS NEARTHESE
UNITS, HEATING ELEMENTS OR INTERIOR SURFACES

OFTHE OVENS. ALL surface units and oven heating elements
may be hot even though they are dark in color. Areas near
surface units may become hot enough to cause burns. During
and after use, do not touch, orlet clothing or otherflammable
materials touch these areas until they have had sufficient time
to cool. Among these areas are the cook top, surfaces facing
the cook top, the oven vent openings and surfaces near these
openings, oven door and window.

Wear Proper Apparel--Loose=fitting or hanging garments

should never be worn while using the appliance. Do not
let clothing or other flammable materials contact hot surfaces.

• Do Not Use Water or Flour on Grease Fires--Smother
the fire with a pan lid, or use baking soda, a dry

chemical or foam=type extinguisher.

• When heating fat or grease, watch it closely. Fat or

grease may catch fire if allowed to become too hot.

• Use Only Dry Potholders =Moist or damp potholders on
hot surfaces may result in burns from steam. Do not let
potholders touch hot heating elements. Do not use a towel or
other bulky cloth instead of a potholder.

• Do Not Heat Unopened Food Containers = Buildup of

pressure may cause container to burst and result in
injury.

• Remove the oven door from any unused range if it is to
be stored or discarded.

IMPORTANT--Do not attempt to operate the range during

a power failure, if the power fails, always turn off the range.
Ifthe range is not turned off and the power resumes, the range

will begin to operate again. Once the power resumes, reset the
clock and oven function.

IMPORTANT iNSTRUCTiONS FOR USINGYOUR

COOKTOP

Know which knob controls each surface heating unit. Place a
pan of food on the unit before turning it on, and turn the unit off
before removing the pan.

Use Proper Pan Size--This appliance is equipped with one or
more surface units of different sizes. Select utensils having flat
bottoms large enough to cover the surface unit heating element.
The use of undersized utensils will expose a portion of the
heating element to direct contact and may result in ignition of

clothing. Proper relationship of utensil to element will also
improve efficiency.

, Utensil Handles Should Be Turned inward and Not Extend Over

Adjacent Surface Elements--To reduce the risk of burns, ignition
of flammable materials, and spillage due to unintentional contact

with the utensil, the handle of the utensil should be positioned so
that itis turned inward, and does not extend over adjacent surface

units.

, Never Leave Surface Elements Unattended at High Heat

Settings--Boilovers cause smoking and greasy spillovers that
may ignite, or a pan that has boiled dry may melt.

, Do Not immerse or Soak Removable Heating Elements--

Heating elements should never be immersed in water. Heating
elements clean themselves during normal operation.

Glazed Cooking Utensils--Only certain types of glass, glass/
ceramic, ceramic, earthenware, or other glazed utensils are

suitable for cook top service without breaking due to the sudden
change in temperature. Check the manufacturer's
recommendations for cook top use.

When flaming foods under aventilating hood, turn the fan on.

IMPORTANT INSTRUCTIONS FOR USING YOUR
OVEN

* Use Care When Opening Oven Door or Warmer Drawer/Bake-

n-Warm TM Double Oven (if equipped)--Stand to the side of the

range when opening the door of a hot oven. Let hot air or steam
escape before you remove or replace food in the oven.

Keep Oven Vent Ducts Unobstructed. The oven vent is located
under the left rear surface element if your model is equipped with
coil elements. The oven vent is located below the backguard for
models equipped with ceramic-glass cook tops. Touching the

surfaces in this area when the oven is operating may cause
severe burns. Also, do not place plastic or heat-sensitive items
on or near the oven vent. These items could melt or ignite.

Placement of Oven Racks. Always place oven racks in desired
location while oven is cool. If rack must be moved while oven is

hot use extreme caution. Use potholders and grasp the rack with
both hands to reposition. Do not let potholders contact the hot
heating elements in the oven. Remove all utensils from the rack
before moving.

Do not use the broiler pan without its insert. The broiler pan and
its insert allow dripping fat to drain and be kept away from the high

heat of the broiler.

* Do not cover the broiler insertwith aluminum foil. Exposed fat

and grease could ignite.

, Protective Liners--Do not use aluminum foil to line the oven

bottom. Only use aluminum foil as recommended in this manual.
Improper installation of these liners may result in risk of electric
shock, or fire.

SELF CLEANING OVENS

Clean in the self-cleaning cycle only the parts listed in this Use & Care Manual. Before self cleaning the oven, remove the broiler
pan and any utensils or foods from the oven.

, Do Not Use Oven Cleaners--No commercial oven cleaner or oven liner protective coating of any kind should be used in or around

any part of the oven.

, Do Not Clean Door Gasket--The door gasket is essential for a good seal. Care should be taken not to rub, damage or move the gasket.

•The health of some birds is extremely sensitive to the fumes given off during the self-cleaning cycle of any range. Move birds to another

well-ventilated room.

IMPORTANT INSTRUCTIONS FOR CLEANING YOUR RANGE

* Clean the range regularly to keep all parts free of grease that could catch fire. Pay particular attention to the area underneath each

surface element. Do not allow grease to accumulate.

* Kitchen cleaners and aerosols--Always follow the manufacturer's recommended directions for use. Be aware that excess

residue from cleaners and aerosols may ignite causing damage and injury.

* Clean Ventilating Hoods Frequently--Grease should not be allowed to accumulate on the hood or filter. Follow manufacturer's

instructions for cleaning.

FOR CERAMIC=GLASS COOK TOP MODELS

* Do Not Cook on Broken Cook Top--If cook top should break, cleaning solutions and spillovers may penetrate the broken cook top

and create a risk of electric shock. Contact a qualified technician immediately.

* Clean Cook Top with Caution--If a wet sponge or cloth is used to wipe spills on a hot cooking area, be careful to avoid a steam burn.

Some cleaners can produce noxious fumes if applied to a hot surface.

important Safety Notice

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances
known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of
potential exposure to such substances.

4

Q 0_ u0_

II' II (D ° ° m' m

o o .....\ _I,,'_%

hi OFF _i OF_ h_ _,,,_c_ OF_ hi o_r _i

® ® ® ® ® ®

Your Electric Range Features Include:

1. Electronic Oven Control with Kitchen Timer.

2. Left Front & Bridge Element Control & Digital Display (some
models) or Dual Element Control (some models).

3. Left Rear Single Element Control & Digital Display or Dual
Element Control (some models).

4. Bake-n-Warm TM Double Oven Control.

5. Bake-n-Warm TM Double Oven Indicator Light.

6. Warming Zone Element Control (some models).

7. Warming Zone Indicator Light (some models).

8. Warming Zone HOT SURFACE Indicator Light (some models).

9. Right Rear Single Element Control & Digital Display or Dual
Element Control (some models).

10. Right Front Dual Element Control & Digital Display.

11. Oven Interior Light with removable Cover.

12. Automatic Oven Door Light Switch (some models).

13. Self-Cleaning Oven interior.

14. Self-Clean Door Latch.

15. Convection Fan & Cover.

16. Adjustable Interior Oven Rack(s).

17. Large 1 piece Oven Door Handle (styles & colors vary).

18. Full width Oven Door with Window (styles & colors vary).

19. Bake-n-Warm TM Double Oven, Drawer Rack, Drawer Handle,
Interior Light (some models) & Window (some models).

20. Easy to clean upswept Cooktop.

21. Ceramic Smoothtop (elements, styles & color will vary).

22. Left Front Single (some models) or Dual Element (some
models).

23. Bridge Element (some models).

24. Left Rear Single (some models) or
Dual Element (some models).

25. Warming Zone Element (some
models).

26. Right Rear Single (some models) or
Dual Element (some models).

27. Right Front Single or Dual Element.

28. Broil Pan (some models).

29. Broil Pan Insert (some models).

30. Roasting Rack (some models).

31. Leveling Legs and Anti-tip Bracket
(included).

R I_ . Im Im

NOTE: The features of your range may
vary according to model type & color.

Before Setting Oven Controls

OVENVENT Oven Vent Location

The oven vent is located under the left side of the control panel

(See Fig. 1). When the oven is on, warm air passes through the vent.

This venting is necessary for proper air circulation inthe oven and good

baking results. DO NOT BLOCK OVEN VENT.

Removing & Replacing Oven Racks

To remove, pull the rack forward until it stops. Lift up front of rack and
slide out. To replace, fit the rack onto the guides on the oven walls.
Tilt the front of the rack upward and slide the rack back into place.

Arranging Oven Racks & Roasting Shelf

ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS COOL
(PRIOR TO OPERATING THE OVEN). Always use oven mitts when

using the oven.

Recommended Rack Positions for Broiling, Baking & Roasting:
Food Rack Position

Broiling hamburgers & steaks See Broil
Broiling meats, chicken or fish See Broil
Cookies, cakes, pies, biscuits 3 or 4

& Muffins

Frozen pies, angel food cake, 1
yeast, bread, casseroles, small
cuts of meat or poultry
Turkey, roast or ham 1 or Roasting Shelf

Roasting Shelf

positioned incorrectly

Fig. 3

Fig. 2 Correct Roasting

Types of Oven Racks & Roasting Shelf

Your range may be equipped with one or more of
the oven rack types shown; Flat Oven Rack

(Fig. 5) and Roasting Shelf (Fig. 6; some
models). To maximize cooking space the
Roasting Shelf should be used in the lowest rack
position to roast large cuts of meat and poultry
(See Fig. 2).

Place Roasting Shelf with care (some models; See Fig. 2). Be sure the Roasting Shelf is level and the front end of the
shelf rests over the front ends of the oven rack glides on both sides of the oven interior(See Figs. 3 & 4).

Flat Oven Rack _ Roasting Shelf

Fig. 5 Fig. 6

Shelf position

Baking Layer Cakes with 1 or 2 Oven Racks

For best results when baking cakes using 2 oven racks, place cookware on rack positions l& 4 (See Fig. 7). For best
results when using a single Flat Oven Rack, place cookware on rack position 2or 3 (See Fig. 8).

Air Circulation in the Oven

For best air circulation and baking
results allow 2-4" (5-10 cm) around
the cookware for proper air
circulation and be sure pans and

cookware do not touch each other,
the oven door, sides or back of the

oven cavity. The hot air must be able
to circulate around the pans and

cookware in the oven for even heat
to reach around the food.

Fig. 7 Fig. 8

Cooktop radiant areas that heat

Models with a Bridge Element Modelswith 4 Dual Elements

il ii

I

Fig. 1

o : o

_i OFF hl OFF h_ t1_ OFF hlOFF hi

_0,,oo _0,,oo 8o_ 8o_R,,,,,Front _ _ RightRear _ @ Rear Frol}t

......... /

/ e t _ :. <¢ /_ea

Left Front Left Rear Right Rear Right Front

About the Ceramic Glass Cooktop

The ceramic cooktop has radiant surface
elements located below the surface of the glass.
The design of the ceramic cooktop outlines the

area of the surface element underneath. Make
sure the diameter of the pan matches the

diameter of the element outline on the cooktop
(See Fig 1). Heat is transferred up through the
surface of the cooktop to the cookware. Only
flat-bottom cookware should be used. The type
and size of cookware, the number of surface
elements in use and the settings, are all factors
that will affect the amount of heat that will spread
to areas beyond the surface elements. The
areas surrounding the elements may become
hot enough to cause burns.

About the Radiant Surface Elements

The element temperature rises gradually and
evenly. As the temperature rises, the element
will glow red. To maintain the selected setting,
the element will cycle on and off. The heating
element retains enough heat to provide a uniform
and consistent heat during the off cycle. For
efficient cooking, turn off the element several
minutes before cooking is complete. This will
allow residual heat to complete the cooking
process.

Fig. 2 (Bridge Element on some models)

NOTE: Radiant elements have a limiter that allows the element to cycle
ON and OFF, even at the HI setting. This helps to prevent damage to
the ceramic cooktop. Cycling at the HI setting is normal and can occur

if the cookware is too small for the radiant element or if the cookware
bottom is not flat (Refer to page 13 for using correct cookware

instructions with the cooktop).

Your range is equipped with radiant surface
burners with different wattage ratings. The ability
to heat food quicker and in larger volumes
increases as the element wattage increases.

NOTE: Please read detailed instructions for

ceramic glass cooktop cleaning in the Care &
Cleaning section and Before You Call

checklist sections of this Use and Care Manual.

Setting Surface Controls

The Electronic Surface Element Control (ESEC)

The Electronic Surface Element Control ("ESEC') feature
includes4 digital display windows. The ESEC feature provides
a numeric digital setting for 4 of the radiant surface element
positions on the cooktop. These settings work the same way
as normal knob setting indicators work except the settings are
displayed in digital windows (Figs. 1thru 4).

The available ESEC Display Settings

The ESEC control provides various heat levels from Hi (Fig. 2)
to Lo (Fig. 4) and OFF (Fig. 1).

Use the chart (Fig. 5) to determine the correct setting for the
kind of food you are preparing, The Simmer settings are used
to simmer and keep larger quantities of foods warm such as £_
stews and soups, The lower Simmer settings are ideal for
delicate foods and melting chocolate or butter, Fig, 1

Note: The size and type of cookware used will influence the
setting needed for best cooking results.

Fig. 2

Radiant surface elements may appear to have

cooled after they have been turned off. The glass surface may
still be hot and burns may occur if the glass surface is
touched before it has cooled sufficiently,

Do not place plastic items such as salt and

pepper shakers, spoon holders or plastic wrappings on
top of the range when it is in use. These items could melt
or ignite. Potholders, towels or wooden spoons could catch fire
if placed too close to the surface elements.

Recommended Surface Cooking Settings

RECOMMENDED SETTINGS FOR SINGLE, BRIDGE & DUAL ELEMENTS

Setting Type of Cooking

HIGH (8- Hi)
MEDIUM HIGH (5- 8)
MEDIUM (3- 5)

Start most foods, bring water to a boil, pan broiling
Continue a rapid boil, fry, deep fat fry
Maintain a slow boil, thicken sauces and gravies, steam

vegetables

0 i:F

Fig. 3 Fig. 4

MEDIUM LOW (2- 3)

LOW (Lo - 2)

Keep foods cooking, poach, stew
Keep warm, melt, simmer Fig. 5

Sett ng Surface Controls

ESEC Hot Element indicator Message (HE)

After using any of the single, dual or Bridge radiant element positions the cooktop will
become very hot. Even after turning the control knob to OFF, the cooktop will remain hot for
some time. The ESEC control monitors the temperature of the cooktop and displays the
message "HE" (hot element) warning when the cooktop is still too hot to touch (See Fig.l). If
the HE message appears in the window, the control can still be turned on again for use.

ESEC Error Indicator Message (Er)

An error message will be displayed (flashing "Er") at power up (or after a power failure) ifANY
of the surface control knobs were left in the ON positions. Ifa power failure should occur, be
sure to set all of the 4 surface control knobs to the OFF position (See Fig. 2). This will reset

the surface controls.
Be sure to reset the clock (See page 15). Once the surface controls have been set to the

OFF positions and the clock has been set with the correct time of day, the surface controls
should return to normal operation. Ifthe surface controls do not function and the "Er"
message remains in any display after following these procedures, contact an authorized

servicer for assistance.

ESEC Lockout Feature ( =- )

The Self-Clean feature will not operate whenever a radiant surface element isON. Conversely
the ESEC feature will not operate during the Self-Clean cycle. Whenever the ESEC Lockout
feature is active, "- - "may appear in any display window (See Fig. 3). If any of the surface
elements are still hot during active Lockout, "HE" will appear in the window instead of the "- -"

message.

Fig. I

The Single Radiant Elements (some models)

Some models have single radiant surface elements at 2 locations; the right rear (Fig. 5) and
left rear (Fig. 6) element positions. The BRIDGE (some models) element position can also be
used as a single element (See Bridge Element Operating Instructions on pages 10-11).

To Operate the Single Elements (some models):

1. Place correctly sized cookware on the radiant surface

element.

2. Push in and turn the surface control knob in either direction
to the desired setting using the ESEC digital display

window for the desired setting (Fig. 4). Turn (do not push)
the knob to adjust the setting if desired. Start most cooking
operations on a higher setting and then turn to a lower
setting to finish cooking. Each surface element provides a
constant amount of heat at each setting. A glowing red
surface heating area extending beyond the bottom edge of

the cookware indicates the cookware is too small for the
surface heating area.

3. When cooking has completed, turn the surface control
knob to OFF before removing the cookware. Note: The HE
message will appear after turning the control knob to OFF if
the cooktop is still hot and will remain on until the heating _.9,,_ .

surface area has cooled sufficiently.

Fig. 4

Note: See page 8, Fig. 5 for recommended control settings.

Fig. 3

Radiant surface elements may appear to have cooled after they have been
turned off. The glass surface may still be hot and burns may occur if the glass surface is
touched before it has cooled sufficiently.

Fig. 6

Left Rear Element

(some models).

Setting Surface Controls

Fig. 1 Fig. 4

O O

i i 0 I:I } / 011

Fig. 2 Fig. 5

/+_

!If P

The Dual Radiant Elements (all models)

The cooktop is equipped with one or more dual radiant surface
elements. Symbols on the control panel (See Fig. 4) are used

to indicate which coil of the dual radiant element will heat. The
symbol shown in Fig. 1 indicates that only the inner coil will

heat. The symbol shown in Fig. 4 indicates that both inner and
outer coils will heat. You may switch from either coil setting at
any time during cooking.

To Operate the Dual Element(s):

1. Place correctly sized cookware on the dual surface
element.

2. Push in and turn the control knob counterclockwise (See
Fig. 2) for smaller cookware or clockwise (See Fig. 5) for
larger cookware.

3. Use the ESEC digital display window for the desired
setting. Turn (do not push) the knob to adjust the setting if
needed. Start most cooking operations on a higher setting

and then turn to a lower setting to finish cooking. Each

surface element provides a constant amount of heat at
each setting. A glowing red surface heating area extending
beyond the bottom edge of the cookware indicates the

cookware is too small for the surface heating area.

4. When cooking has completed, turn the surface control
knob to OFF before removing the cookware. Note: The HE
message will appear after turning the control knob to OFF
ifthe cooktop is still hot and will remain on until the radiant
heating surface area has cooled sufficiently. Note: See
page 8, Fig. 5 for recommended control settings.

Fig. 3 Fig. 6

The Bridge Radiant Element (some models)

Some ceramic cooktops are equipped with a"BRIDGE"
surface element located at the left front and middle (See
Fig. 10) positions. The Bridge can be used when cooking
with rectangular (like a griddle) or oval shaped cookware
(Fig. 10). The element will maintain an even temperature
setting across both portions of the Bridge. Ifneeded for
normal cookware, the Bridge element can work like a
single element without the Bridge (See Fig. 8).

Bridge element operation symbols are located on the
control panel on each side of the Bridge element control

knob. These symbols indicate the direction to turn the
control knob when operating the Bridge element. The
symbol in Fig. 7 indicates that only the single portion of
the Bridge element wil heat (See Fig. 8). The symbol in
Fig. 9 indicates that both the single and Bridge portions
of the element will heat together (Fig. 10). You may
switch from either of these settings at any time during
cooking with the Bridge element.

Radiant surface elements may appear to have

cooled after they have been turned off. The gJass surface may
still be hot and burns may occur if the glass surface is
touched before it has cooled sufficiently.

Fig. 7 Fig. 9

i

] ii i i ' _ ii L i

i i

iii iii

Fig. 8 Fig. 10

Bridge element without Bridge Bridge element with Bridge

portion (some models), portion (some models).

10

To Operate the Bridge Element (some models):

1. Place correctly sized cookware on the Bridge surface
element.

O

OF !_

Fig. 1

Fig. 2

#%

{¸.¸¸9

0 F !

Fig. 3

Fig. 4

2. Push in and turn the control knob counterclockwise (See
Figs. 1 & 2) to heat the portion of the Bridge element for
normal shaped cookware or clockwise (See Figs. 3 & 4) for
larger or rectangular shaped cookware.

3. Use the ESEC digital display window for the desired
setting. Turn (do not push) the knob to adjust the setting if
needed. Start most cooking operations on a higher setting

and then turn to a lower setting to finish cooking. Each

surface element provides a constant amount of heat at
each setting. A glowing red surface heating area extending
beyond the bottom edge of the cookware indicates the

cookware is too small. Please note that not all cookware
will fit the Bridge element correctly.

4. When cooking has completed, turn the surface control
knob to OFF before removing the cookware. The HE
message will appear in the display after turning the control

i

i

i

knob to OFF if the cooktop is still hot and will remain on
until the radiant heating surface area has cooled
sufficiently. Note: See page 8, Fig. 5 for recommended

control settings.

The BRIDGE element may also be used in combination with the
left rear single element. Because these elements have 2

different controls, one element can be used to cook while the
other element may be used to keep food warm (See Fig. 5).

Fig. 5

Radiant surface elements may appear to have

cooled after they have been turned off. The glass surface may
still be hot and burns may occur if the glass surface is
touched before it has cooled sufficiently.

11

Operating the Warming Zone (some models)

The purpose of the Warming Zone is to keep hot cooked foods at serving temperature. Use the Warming Zone to keep
cooked foods hot such as; vegetables, gravies, casseroles, soups, stews, breads, pastries and oven-safe dinner plates.
Always start with hot food. It is not recommended to heat cold food on the Warming Zone.

All food placed on the Warming Zone should be covered with a lid or aluminum foil to

maintain quality. For best results, when warming pastries or breads, the cover should have
an opening to allow moisture to escape. Do not use plastic wrap to cover food. Plastic
may melt onto the surface and be very difficult to clean. Use only plates, utensils and
cookware recommended for oven and cooktop use on the Warming Zone.

Always use pot holders or oven mitts when removing food from the Warming

Zone as cookware and plates will be hot.

To Set the Warming Zone Control (some models):

1. To set the control, push in and turn the knob. The On indicator light will come on (See
Figs. 1 and 2). The temperatures are approximate, and are designated by HI, MED and
LO. However, the control can be set at any position between HI and LO for different levels
of heating (Fig. 1).

2. When done, turn the control to OFF. The Warming Zone Hot surface indicator light
will remain on until the Warming Zone cools to a moderate level (See Figs. 1& 2).

Temperature Selection

Refer to the table for recommended Warming Zone food settings (Fig. 3). If a particular food is
not listed, start with the medium level, and adjust as needed. Most foods can be kept at
serving temperatures by using the medium level.

Fig. 1

The Warming Zone will not glow red when it ishot, but becomes hot enough to

cause burns. Avoid placing hands on or near the Warming Zone until the Warming Zone Hot
surface indicator light is off.

Warming Warming Zone Warming

Zone Hot Surface Zone

indicator Light indicator Light Control

Warming Zone Recommended Food

Settings Table

Food Item Heating

Level

Hot Beverages HI

Warming Zone

Fried Foods HI

Vegetables MED

Soups (Cream) MED
Stews MED

Sauces MED
Meats MED
Gravies LO

Eggs LO
Dinner Plates with Food LO

Casseroles LO
Breads/Pasteries LO

Fig. 2 (some models)

Fig. 3

12