Frigidaire GLEB27M9EBA, GLEB27M9EBB, GLEB27M9EQA, GLEB27M9EQB, GLEB27M9ESA Installation Guide

...

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUAUFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance. Your new waJ[ oven has been designed to fit a Jim[ted variety of cutout sizes to make the job of installing

eaMer, The first step of your installation should be to measure your current cutout dimenMons and compare them to the cutout dimensions chart below for your mode[, You may find little or no cabinet

work is necessary.

Do not remove spacers (if equipped) on the side walls and/or on the back of the bui[t4n

oven. These spacers center the oven in the space provided, The oven must be centered to prevent excess heat buildup that may result [n heat damage or fire.

NOTES: Hob for

1. Base must be capable of supporting 225 pounds (102 kg), _ [ ..... Cable

2. Allow at least 21 (53,3 cm) clearance in front of oven for door Min /_"_'[eft depth when it isopen. < <--___ _ depending

" I" (2.5cm) (right or

side

, Dimension G (cutout depth) is _ -._ k_j_ . / on model)

critical to the proper installation of ' °--L _ -- .:, /

the builtdn oven. If the oven _-_ _ J_-. ._. -'_:- -G'__ /

decorative trim does not butt .......... "_-_ "_c_ F_. -- '/

against the cabinet verify

.......@1 N

dimension Gto assure it is the 8 _'_ __JC__" / required depth. _ 40-1s/16" /

........."> . / (29.2 cm) [_&'---__ _'_-- Max.

Door Open "_'_ , _ k _ -'I_

, _, _'%_ _S_acer _.1_\ I : 1!/;¢' ___._.. .

tsee note Z} ......x D..._ _' "_ "-(3.2 crn) / Electrical

Suggested distance flora floor .........< _ ............. ,_ _ Min./ Junction Box

is 111/2"(29.2 cm). "'A. z tb cm2vvlae vvooa_ - _ (right or left side) Minimum required distance is 4 -. Spacer if Needed Y2" (11.4 cm) Figure 1

" (104 cm) /_-_

11kS" _{_Z\ ; ?-c_-c.,.._p 3" (7.6 cm)

27" (686 cm)Wall Oven 27 (686)

30" (762 cm) Wall Oven 30 (76.2)

27" (686 cm) Wall Oven 247/s(632) 25¼ (64.1)

30" (762 crn) Wall Oven 28Y_(724) 29 (737)

All dimensions are stated in inches and (cm)

Printed in United States

42sA (108.6)

24% (625) 24Y2 (622)

28¼ (718) 24Y2 (622)

41% (1045)

411A (104%

41¼ (104.8) 27Vs (68 9) Min

41¼ (104.8) 3@A(76 5) Min

WN 318201521 (0503) Rev A

English - pages 1-6

Espanol - paginas 7-12

Important Notes to the Installer

1. Read all instructions contained in these installation instructions before installing tile combination oven.

2. Remove all packing material from the oven compartments before connecting the electrical supply

to the wall oven.

3. Observe all governing codes and ordinances.

4. Be sure to leavethese instructions with the consumer.

5. Oven door may be removed to facilitate installation.

6. THS COMBINATION OVEN [S NOT APPROVED FOR STACKABLE OR SDE-BY-SDE INSTALLATION.

Important Note to the Consumer

Keep these instructions with your Owner's Guide for future reference. Do not discard oven removal tools found in the

literature bag.

IMPORTANTSAFETYINSTRUCTIONS

• Be sure your combination oven is installed and

grounded properly by a qualified installer or service technician.

This wall oven must be electrically grounded in accordance with Iota[ codes or, in their absence, with the Nationa[ EJectricaJCode ANSJ/NFPA

No.70- tatest edition in United Sates, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, in

Canada.

Stepping, leaning or sitting on the

door of this wall oven can result in serious injuries and can aIso cause damage to the wall oven.

1. Carpentry

Refer to figure I for the dimensions applicable to your appliance, and the space necessary to receive the combination oven. The oven support surface may be solid plywood or similar material, however the surface

must be leveled from side to side and from front to rear.

2. Electrical Requirements

This combination oven must be supplied with the proper voltage and frequency, and connected to an individual,

properly grounded branch circuit, protected by a circuit breaker or fuse, having amperage as noted on the rating

plate (the rating plate is located on the side trim).

Observe all governing codes and local ordinances

1. A 3-wire or 4-wire single phase 120/240 or !20/208 Volt, 60 Hz AC only electrical supply is required on

a separate circuit fused on both sides of the line (time-delay fuse or circuit breaker is recommended).

DO NOTfuse neutral. The fuse size must not exceed the circuit rating of the appliance specified on the nameplate.

2. The combination oven can consume up to 5200W when both ovens are operating. Use a circuit

breaker of 30 Amp with wire gauge #10 AWG.

NOTE: Wire sizesand connections must conform with the fuse size and rating of the appliance in accordance

with the American National Electrical Code ANS!/NFPA No. 70qatest edition, or with Canadian CSA Standard

C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

• Never use your wall oven for warming or heating the room. Prolonged use of the wall oven without adequate ventilation can be dangerous.

The electrical power to the oven must

be shut off while Hne connections are being made. Failure to do so could result [n serious injury or

death.

An extension cord should not be used

with this appliance. Such use may result in a fire, electrical shock, or other persona[ injury.

3. This combination oven should be connected to the fused disconnect (or circuit breaker) box through

flexible armored or nonmetallic sheathed (:able. The flexible armored cable extending from the appliance

should be connected directly to the junction box. The

junction box should be located as shown in Figure 1

and with as much slack as possible remaining in the cable between the box and the appliance, so the latter can be moved if servicing is ever necessary.

4. A suitable strain relief must be provided to attach the flexible armored cable to the junction box.

Electrical Shock Hazard

• Electrka[ ground is required on this appliance,

• Do not connect to the electrical supply until appliance is permanently grounded.

• Disconnect power to the iunct[on box before

making the eJectrica[ connection,

• This appliance must be connected to a grounded, meta[Hc, permanent wiring system,

or a grounding connector should be connected

to the grounding terminal or wire [ead on the appliance.

• Do not use a gas supply line for grounding the appliance.

Failure to do any of the above could result in a

fire, personal injury or electrica[ shock.

In cold weather shipping and storage

conditions, make sure that oven is in final location at least three (3) hours before switching on power.

Switching on power while oven is still cold may damage the oven controls.

Where local codes permit connecting the appliance- grounding conductor to the neutral (white) wire (see figure 2):

1. Disconnect the power supply.

2. In the circuit breaker, fuse box or junction box: connect appliance and power supply cable wires as shown in Figure 2.

Cable from Power Supply

White Wire (Neutral)

Wires

Red

Wires

Box

(Neutral)

Ground Wire U.L.-Listed Conduit (Bare or Green Wire) Connector (or CSA listed)

Cable from appliance

Figure 2

3-WIRE GROUNDED JUNCTION BOX

3. Electrical connection

It is the responsibility and obligation of the consumer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance with the

National Electrical Code ANS!/NFPA No. 70qatest edition, or with CSA Standard C22.1, Canadian

Electrical Code, Part 1, and local codes and ordinances.

ElectricaJ ground is required on this appliance.

This appliance is equipped with a copper conductor flexible cable. If connection is made to aluminum house

wiring, use only special connectors which are approved for joining copper and aluminum wires in accordance

with National Electrical Code and local codes and ordinances.

This appliance is manufactured with a white neutral power supply wire and a frame connected green or bare copper grounding wire.

Improper connection of aluminum

house wiring to copper leads can result in a short circuit or fire. Use only connectors designed for

joining copper to aluminum, and follow the

manufacturer's recommended procedure closely.

You may not ground the oven

through the neutral (white) wire if oven is used in a new branch circuit installation (!996 NEC), mobile home, recreational vehicle, or where local codes do not permit grounding through the neutral (white) wire, When grounding through the neutral (white) wire is prohibited, you must use a 4-wire power supply cable, See Figure 3, Failure to heed this warning may result in electrocution or other serious personal injury.

tf oven is used in a new branch circuit installation (!996 NEC), mobile home, recreational vehicle, or where tocal codes DO NOT permit grounding

through the neutrat (white) wire (see figure 3):

1. Disconnect the power supply.

2. Separate the green (or bare copper) and white appliance (:able wires.

3. In the circuit breaker, fuse box or junction box: connect appliance and power supply cable wires as shown in Figure 3.

Cable from Power Supply

Ground

Wires

Ground Wire (Bare

Wire)

Junction Box U.L.-Listed Conduit

Connector (or CSA listed)

Cable from appliance

Figure 3

4-WIRE GROUNDED JUNCTION BOX

DO NOT ground to a gas supply pipe. DO NOT connect to electrical power supply until appliance is permanently grounded. Connect the ground wire before turning on the power (Figure 3).

Heavy Weight Hazard

Use 2 or more people to move and install this

combination oven.

Failure to follow this instruction can result in injury

or damage to the unit.

4. Cabinet Installation

The combination oven can tip when

the door is open. The mounting brackets supplied with the oven must be attached to the cabinet and

the appliance to prevent tipping of the wail oven and injury to persons.

Mounting Brackets Installation Instructions

1. Unpack the wall oven. Remove the bottom trim taped on the oven side panel. Find the 2 mounting brackets and screws included in the literature package.

2. Install tile mounting bracket in the wall cabinet as shown in Figure 4. Note: To prevent damage to cabinet,

it isrecommended to drill 1/16" (0.16 cm) dia. pilot holes before installing the mounting brackets.

I° H

22 3/16" *

(56.4 cm)

If connecting to a 4-wire electrical

system (mobile homes), the appliance frame MUST NOT be connected to the neutral wire of the 4-wire

electrical system.

NOTE TO ELECTRICIAN: The armored cable leads supplied with the appliance are Ubrecognized for

connection to larger gauge household wiring. The insulation of the leads is rated at temperatures much higher than temperature rating of household wiring. The current carrying capacity of the conductor is governed by the temperature rating of tile insulation around the wire, rather than tile wire gauge alone.

* If wood spacers are needded (seefigure1 ) please calculate this dimension from the top of the spacer to

the middle of the mounting bracket.

j_m

Figure 4

3.Insert the oven into the cabinet opening. Slide oven

inward leaving !_/2" (3.8 cm) clearance between the oven and front of cabinet (seeFigure 5). Pull the armored cable through the hole for it in the cabinet and toward the junction box while moving the appliance inward.

+ 8 hidden pages