Frigidaire NGS21TZAW4, NGS21TZAW3, NGS21TZAQ4, NGS21TZAQ3, NGS21TZAB4 Owner’s Manual

...

TopMount Welcome ....................... 2

Safety Instructions ............ 3

Installation - ,.dud=Connecting

OptionalIce MakerToWaterSupply ..... 4 - 5

Door

Removal & Reversal ....... 6 - 9

Features at a Glance ........ .10

Temperature Controls ....... 11

Looking Inside .......... 12 - 14 g

Ice Service .................... 15 U

Food Storage B

& Energy Saving Tips ....... 16

Normal Operating Sounds .. 17

Care & Cleaning .......... 18- 19 r_

Warranty ...................... 20 W

Espanol ........... 23

Frangais ........... 45

Before You Call ............... 21

READ AND SAVE THESE INSTRUCTIONS P/N240400105(0108)

Congratulations on your purchase of a new refrigerator! We

here at Electrolux Home Products are very proud of our product and we are completly committed to providing you

with the best service possible. Your satisfaction is our #1

priority. Please read this Use &Care Manual very carefully. Itcontains

valuable information on how to properly maintain your new

refrigerator.

We know you'll enjoy your new refrigerator and Thank You for choosing oar product. We hope you consider us for future

purchases.

PLEASE READ AND SAVE THESE INSTRUCTIONS

This Use & Care Manual provides specific operating

instructions for your model. Use your refrigerator only as instructed in this manual. These instructions are not meant

to cover every possible condition and situation that may occur. Common sense and caution must be practiced when

installing, operating and maintaining any appliance.

Please record your model and serial numbers below for

future reference. This information is found on your serial

plate located inside the refrigerator compartment.

Questions?

1-800-944-9044

(United States)

1-866-213-9397

(Canada)

Extend Your Warranty Protection

With An

Extended Service Contract

CALL 1-800-944-9044

To Enjoy These Benefits:

Total freedom from repair bills so

unexpected repairs won't upset your budget.

NOTE: Use onlysoap and water toclean serial plate.

Model Number:

Serial Number:

Purchase Date:

SerialPlate

Fast, convenient toll-free service is just

a phone call away. Top-quality repairs by factory-trained

experts.

Quick access to genuine replacement parts so you can rest assured your

refrigerator is repaired with the proper components.

Please attach sales receipt

here for future reference.

Please complete and mail in the Product Registration Card included with your refrigerator.

FOR YOUR SAFETY

Do not store or use gasoline, or other flammable liquids inthe vicinity of this or any other appliance. Read pro-

duct labels for warnings regarding flammability and other

hazards. Do not operate the refrigerator inthe presense of

explosive fumes. Avoid contact with any moving parts of automatic ice

maker.

Remove all stables from the carton. Staples can cause severe cuts, and also destroy finishes if they come in contact with other appliances or furniture.

CHILD SAFETY

Destroy or recycle the carton, plastic bags, and any exterior

wrapping material immediately after the refrigerator is

unpacked. Children should NEVER use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly

cause suffocation.

PROPER DISPOSAL OF YOUR REFRIGERATOR

OR FREEZER

Risk of child entrapment _._._ Child entrapment and

suffocation are not problems of the past. Junked or abondoned

refrigerators or freezers are still dangerous- even if they will sit

for "just a few days." If you are getting rid of your old refrigerator

or freezer, please follow the instructions below to help

prevent accidents. Before you throw away your old refrigeratorl freezer:

Remove doors.

Leave shelves in place so children may not easily climb inside.

Have refrigerant removed by a qualified service technician.

ELECTRICAL INFORMATION

The refrigerator must be plugged into its own dedicated 115 Volt, 60 Hz., AC only electric outlet.

The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. It must be plugged directly

into a properly grounded three-prong receptacle. The receptacle must be installed in accordance with local

codes and ordinances. Consult a qualified electrician.

Do not use an extension cord or adapter plug.

Immediately repair or replace any power cord that becomes frayed or damaged.

Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.

Unplug the refrigerator before cleaning and before

replacing a light bulb to avoid electrical shock.

Performance may be affected if the voltage varies by

10% or more. Operating the refrigerator with insufficient

power can damage the compressor. Such damage is

not covered under your warranty.

Do not plug the unit into an outlet controlled by a wall switch or pull cord to prevent the refrigerator from being

turned off accidentally. Avoid connecting refrigerator to aGround Fault

Interruptor (GFI) circuit.

NOTE: Turning the refrigerator temperature control to 1!0"

turns off the compressor, but does not disconnect

electrical power to the light bu!b or other electrical components.

Groundingtype wallreceptacle

Do not, under _'_ any circumstances, I

cut, remove, / or bypassthe /

grounding prong, j)

Powercordwith

3-pronggroundedplu_

This Use & Care Manual provides specific operating

instructions for your model. Use the refrigerator only as instructed in this Use & Care Manual. Before starting the

refrigerator, follow these important first steps. LOCATION

Choose a place that is near a grounded electrical outlet.

Do Not use an extension cord or an adapter plug. If possible, place the refrigerator out of direct sunlight

and away from the range, dishwasher or other heat sources.

The refrigerator must be installed on a floor that is level and strong enough to support a fully loaded refrigerator.

Consider water supply availability for models equipped with an automatic ice maker.

INSTALLATION

Do Not install the refrigerator where the temperature

will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper

temperatures inside the refrigerator.

Do Not block the toe grille on the

lower front of your refrigerator. Sufficient air

circulation is essential for the proper operation of

your refrigerator.

Installation Clearances

Allow the following clearances for ease of installation,

proper air circulation, and plumbing and electrical

connections:

Sides & Top 3!8"

Back I"

LEVELING

All four corners of your refrigerator must rest firmly on a solid floor. Your refrigerator is equipped with adjustable front

rollers to help level your unit.

To Level Your Refrigerator:

1. Remove toe grille.

2. Use flat-blade screwdriver or 3/8" socket wrench to adjust front rollers.

NOTE: Raise the front of the refrigerator enough so the doors close freely when opened halfway. The refrigerator

should slope ¼'! to ½" from front-to-back. Then level the refrigerator from side to side.

NOTE: if You see black coils/tubing Onthe back of Your

refrigerator (air-coo!ed condenser) leave 31'clearance at

top of refrigerator,

DOOR OPENING

NOTE: Ifyour refrigerator is placed with the door hinge

side against a walt, you may have to allow additional space so the door can be opened wider.

Your refrigerator should be positioned to allow easy access to a counter when removing food. To make this possible, the direction in which the doors open can be reversed. See Door Removal & Reversal Instructions on page 6.

Raise

Installation - Connecting Optional Ice Maker To Water Supply

To avoid electric shock, which can cause death or severe personal injury, disconnect the

refrigerator from electrical power before connecting a water supply line to the refrigerator.

To Avoid Property Damage:

Copper tubing is recommended for the water supply line. Water supply tubing made of %" plastic is not

recommended since it greatly increases the potential for water leaks, Manufacturer will not be responsible for

any damage if plastic tubing is used for supply line,

• DO NOT install water supply tubing in areas where temperatures fall below freezing, Chemicals from a malfunctioning softener can damage the ice maker, If the ice maker is connected to soft

water, ensure that the softener is maintained and working properly,

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need

Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips TM screwdriver

Access to a household cold water line with water pressure between 20 and 120 psi. A water supply line made of ¼ inch(6.4 mm) OD, copper tubing. To determine the length of copper tubing needed,

you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water

pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.

A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

NOTE: Water line kit number 5303917950, available from your appliance deater at additional cost, contains 25 feet (7.6 meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nohpiercing), (2) ¼ inch brass compression nuts, (2)

ferrules/sleeves, and instructions for installinga water supply line.

To Connect Water Supply Line To Ice Maker Inlet Valve

Disconnect refrigerator from electric power source.

Place end of water supply line into sink or bucket. Turn ON water supply

and flush supply line until water is clear. Turn OFF water supply at shut off valve.

Unscrew plastic cap from water valve inlet and discard cap.

Slide brass compression nut, then ferrule (sleeve) onto water supply line,

as shown.

Push water supply line into water valve inlet as far as it will go (¼ inch).

_Steel

Compression

Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

With steel clamp and screw, secure water supply line to rear panel of

refrigerator as shown.

Coil excess water supply line (about 2½ turns) behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

Turn ON water supply at shutoff valve and tighten any connections that _Copper waterline

leak. _ !r°mh_t_h01d_tersUPply

Reconnect refrigerator to electrical power source. _- (Includeenoughtubinginlooptoallow

10. To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/

mo_ngref_ga_ outfordenning.)

OFF position of arm).

Clamp

Bra_

Nut

water line

IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may

cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be discolored or have poor flavor. Discard ice made during the first 24 hours.

Door Removal and Reversal Instructions

"_ TOOLSNecessary:

B(X_'n

Top Hinge

PlugsCabinetHole _" _ Top Hinge

Hinge Hole _ Handle Hole Plug Plug

Screw _ Stop

Washer

_Hlnge

Hinge Hole Plug Handle

Door Stop Door

Screw StOl

_Pin

_ BHing°t_em

roeGrille

Door

Hinge

_Pin

Center

Hole

Hinge

DOOR REMOVAL AND REVERSAL INSTRUCTIONS:

NOTE: If you have stainless steel doors -- go to the Removing Stainless

Steel Doors and Handles Section on page 9.

NOTE: The direction in which your refrigerator doors open (door swing)

can be reversed, from left Io right or right to left, by moving the door

qinges from one side to the other. Reversing the door swing should be performed by a qualified person.

IMPORTANT: Before you begin, turn the refrigerator temperature control

to "0" and remove the electrical power cord from the walt outlet. Remove any food from door shelves.

1 Remove toe grille and top hinge cover.

2. Remove top hinge with 3!8" hex driver and lift freezer door off of center hinge pin. Set door aside.

3. Unscrew center hinge pin using adjustable wrench and save for reassembly. Ensure DlaSticwasher stays on hinge pin.

4. Lift refrigerator door off of bottom hinge and set aside.

5. Remove center hinge and shim by removing inside screw and loosening two outside screws enough to allow hinge and shim to

slide out. Tighten screws.

6. Loosen two outside screws on opposite side of refrigerator, remove inside screw and install center hinge.

7. Remove bottom hinge with 3/8" hex driver. Reinsert two outside screws in holes and tighten. Inside screw will go to opposite side in step 8.

8. Remove two outside screws on opposite side of refrigerator and install bottom hinge. Insert and tighten screw saved from step 7.

9. Unscrew bottom hinge pin using adjustable wrench. Move hinge pin to other hole in hinge and tighten with adjustable wrench.

10. Reverse door handles (see instructions on next page).

11. Move freezerand refrigerator doorstops to opposite side. Before starting screws, use an awl to puncture the foam.

12. Position refrigerator door onto bottom hinge pin and screw center hinge pin through center hinge into top of door. Close refrigerator door to help align hinge hole.

13. Tighten center hinge pin with adjustable wrench.

14. Remove cabinet and hinge hole plugs and move to opposite side.

15. Lower freezer door onto center hinge pin.

16. Close freezer door. Have an assistant lift up on opposite side of door while tightening screws to install top hinge.

17. Replace toe grille and top hinge cover.

18. Plug in electrical power cord and turn refrigerator temperature control to center position. Adjust setting as necessary.

Door Removal and Reversal Instructions (continued)

NOTE: Some models have "pocket" handles, which are recessed into the sides of the door. On these models, only the hinges will need to be reversed.

TO REMOVE FREEZER HANDLE:

(Handles may be easier to reverse while doors are off.)

1. Remove two screws attaching handle to bottom of freezer door.

2. Remove short trim piece by sliding trim straight up and off of handle bracket.

3. Remove screw attaching top of handle to door.

4. Magnetic Nameplate Models: Gently pry magnetic nameplate frame from

door. Remove nameplate from its frame, turn frame upside down and

install inold handle holes. Insert magnetic nameplate into frame. Self-Adhesive Nameplate Models: Gently peel off nameplate from door

and reapply over old handle holes.

TO ATTACH FREEZER HANDLE:

1. Reinstall handle on opposite side, using same hole as nameplate.

2. Attach handle to bottom of door.

3. Slide trim piece straight down onto handle bracket.

Trim--

Scr_ (some models)

Nameplate

Self Adhesive

Nameplate

TO REMOVE FREEZER HANDLE:

(Handles may be easier to reverse while doors are off.)

Nameplate Nameplate I

TO REMOVE FREEZER HANDLE:

(Handles may be easier to reverse while doors are off.)

1. Remove two screws attaching handle to bottom of freezer door.

2. Remove button plug using edge of putty knife.

3. Remove screw on side of freezer door and remove handle. TO ATTACH FREEZER HANDLE:

1. Secure side of handle to door and replace button plug.

2. Secure handle to bottom of door.

1. Remove two screws attaching handle to bottom of freezer door.

2. Swing bottom of handle away from the door and slide handle straight up and off of dovetail button.

3. Remove screw and dovetail button and installon other side, using the same holes as nameplate.

4. Magnetic Nameplate Models: Use putty knife to gently pry magnetic nameplate frame from door. Remove nameplate from itsframe, turn frame upside down and install in old handle holes. Insert magnetic nameplate

intoframe. Self-Adhesive Nameplate Models: Use putty knife to gently peel off name

plate from door and reapply over old handle holes.

TO ATTACH FREEZER HANDLE:

1. Start with handle offset away from door. Place top of handle over dovetail button, swing handle into an upright position and pull downward, locking it intoplace.

2. Secure bottom of handle with two screws removed earlier.

Button

P!ug

NOTE: To remove freezer handle, refer to figure 3 on page 9.

Door Removal and Reversal Instructions (continued)

TRIM REMOVAL (FULL-LENGTHTRIM MODELS ONLY)

q some models, the refrigerator door has a full length tnm oiece which

continues from the bottom of the handle to the bottom of the door. The top of the trim attaches to the handle bracket (Figure 1) or fits around the base

of the handle (Figure 2) An adhesive "trim lock" ispositioned about halfway down. The bottom of the trim is held in place Dyeither an adhesive trim lock.

or a trim lock with two prongs inserted into a hole on the face of the door

TO REMOVE TRIM:

1. Remove trim by gently pulling trim lock areas out and away from door.

2. When trim is free from door. slide the trim straight down and away from base of handle.

NOTE: For models with short handle trim. remove by sliding trim straight down and off of handle bracket.

TO REMOVE REFRIGERATOR HANDLE:

(Handles may oe easier to reverse while doors are off._

Figure 1 Style Handles

1. Remove two screws attaching handle to top of refrigerator door.

2. Remove screw attaching bottom of handle to door.

3. Remove two hole plugs and hinge pin plug on _opof door and install on opposite side. Use Phillips head screwdriver to remove plastic screw plug from front of door and install on opposite side

Figure 2 Style Handles

1. Remove two screws attaching handle to top of refrigerator door.

2. Swing top of handle away from door and slide handle down and off of dovetail button.

3. Remove screw and dovetail button and install on other side, moving hole plugs from corresponding holes to opposite side.

TO ATTACH REFRIGERATOR HANDLE:

Figure 1Style Handles

1. Secure bottom of handle with screws.

2. Secure top of handle with screws.

Figure 2 Style Handles

1. Start with handle offset away from door. Place bottom of handle over dovetail button, swing handle into an upright position and pull upward,

locking it into place.

2. Secure top of handle with screws. TO ATTACH TRIM:

1. Slide both trim locks out of trim.

2. Insert new adhesive trim locks contained in your literature pack. NOTE: Trim lock must be removed and installed bY sliding over the

two donut shaped areas,

Full

Length

Figure 1

Adhesive

Trim

LockHandle

over

Dovetail

Adhesive

Lock

Trim Lock

3. Install trim to handle by sliding under base of handle. Carefully align

trim and press down at trim lock locations.

4. Use rubbing alcohol to remove any adhesive residue from old trim

lock locations.

Figure 2

Door Removal and Reversal Instructions (continued)

TO REMOVE REFRIGERATOR HANDLE:

(Handles may be easier to reverse while doors are off.)

1. Remove two screws attaching handle to top of refrigerator door.

2. Remove button plug using edge of putty knife.

3. Remove screw on side of refrigerator door and remove handle.

4. Reverse freezer and refrigerator handles as shown infigure 3.

TO ATTACH REFRIGERATOR HANDLE:

1. Secure side of handle to door and replace plug button.

2. Secure handle to top of door.

Button _Sorew

Refrigerator Door Without Trim

Figure 3 - Handle Reversal

REMOVING STAINLESS STEEL DOORS AND HANDLES

Use care when using tools near surface of stainless steel doors to avoid scratching.

To Remove Doors

Stainless steel doors are not reversible. Follow these steps to remove doors.

1. Remove toe grille and top hinge cover.

2. Remove top hinge and lift freezer door off of center hinge pin. Set door aside.

3. Unscrew center hinge pin using adjustable wrench and save for

reassembly. Ensure plastic washer stays on hinge pin.

4. Lift refrigerator door off of bottom hinge and set aside.

5. Remove center hinge and shim by removing inside screw and loosening two outside screws enough to allow hinge to slide out.

6. Remove bottom hinge. Reinsert two outside screws in holes and tighten.

7. Reverse steps 1 - 6 to reinstall doors

To Remove Handles

1. Firmly hold freezer handle while loosening set screws with 3/32" allen wrench. Remove freezer handle.

2. Repeat step 1for refrigerator door.

Shoulder

Typical Handle

Freezer Light

Ice Bucket

Freezer

Control

Retrlgerator Control

Dell Drawer Covet

Dell Drawer

Half Shelf Wine Rack

Special Item

Full Shelf

Crisper Drawers

Fixed Door Bin

Door Rack

Dairy Door

Tall Bottle

Retainer

Snugger

Door Bin

Fixed Door Sin

Door Rack

_Toe Grille

Features may vary according to model

COOL DOWNPERIOD

To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 to 12 hours before loading

it with food.

REFRIGERATOR & FREEZER CONTROLS

NOTE: When first setting the controls or when changing asetting, wait 24 hours for the temperature to stabilize before

making additional changes.

TEMPERATURE ADJUSTMENT

NOTE: When first turning refrigerator on, move refrigerator and freezer controls to • which is the recommended

initial setting. After 24 hours, adjust the controls as needed.

Adjust temperature gradually: move the knob in small

increments, allowing the temperature to stabilize,

For colder temperatures, turn the knob towards Cold For warmer temperatures, turn the knob towards Warm.

Turning the refrigerator control will change temperatures in both compartments. For example, if the refrigerator control isturned to a colder setting, the freezer control may have to be adjusted to a warmer setting. Turning the freezer control will change only the freezer temperature.

To maintain temperatures, a fan circulates air in the refrigerator and freezer compartments. For good circulation, do not block

cold air vents with food items.

Recommended

setting

Freezer Control ,some models_

Refrigerator Control ,some mode]s_

IMPORTANT: Turning the refrigerator tem3-

erature control to "0" turns off the com- pressor, but does not

disconnect the power to the light bulb and other

electrical components

Refrigerator & Freezer Control tsome models_

TEMPERATURE ADJUSTMENT GUIDE

If Refrigerator compartment Is Too Warm Turn Refrigerator Control Slightly Towards Cold.

If Refrigerator compartment Is Too Cold Turn Refrigerator Control Slightly Towards Warm.

If Freezer compartment Is Too Warm Turn Freezer Control Slightly Towards Colder.

If Freezer compartment Is Too Cold Turn Freezer Control Slightly Towards Warmer.

To Turn Refrigerator Off Turn Refrigerator Control To 0.

To avoid personal injury or property damage, handle

tempered glass shelves carefully. Shelves may break suddenly if

nicked, scratched, or exposed to sudden temperature change.

SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting

the shelves, remove all food.

To adjust sliding shelves:

O Remove shelf by pulling forward to stop position.

Lift front edge up and pull out.

Replace the shelf on any pair of rails by reversing this procedure.

To adjust cantilever shelves:

NOTE: Cantilever shelves are Supported at the back of the refrigerator. Cantilever shelves are available in either glass or wire.

Lift front edge up. Pull shelf out.

Replace the shelf by inserting the hooks at rear of the shelf into the wall bracket. Lower the shelf into the desired slots and lock into position.

SpillSafe TM glass shelves (some models) catch and hold accidental spills. In

some models, the SpillSafe TM shelves slide out for easy access to food and for fast cleaning. The shelves slide oat independently of the cantilever brackets. Just pull the front of the shelf forward. The shelf can be extended as far as the

stopper will allow but it is not removable from the cantilever bracket.

Sliding Wire Shelf

Sliding Glass Shelf

Full Width Cantilever Glass Shelf

,-,...

Cantilever Glass Shelf - Fixed and Sliding

Looking lnside (continued)

DOOR STORAGE

Door bins, shelves, and racks are provided for convenient storage of jars, bottles, and cans. Frequently used items

can be quickly selected. Some models have door racks or bins that can accommodate

gallon-sized plastic drink containers and economy-sized jars and containers. Some racks are adjustable for maximum

storage capacity.

The dairy compartment, which is warmer than the general food storage section, is intended for short term storage of

cheese, spreads, or butter.

Door Rack

TALL BOTTLE RETAINER (SOME MODELS)

The Tall Bottle Retainer keeps tall containers in the bin from falling forward when opening or closing the refrigerator door.

To install, hold the retainer at the top, and slide it over the outside wall of the bin, as shown in the diagram. The Tall

Bottle Retainer works best with a Bin Snugger.

Tall Bottle Retainer (left) and Bin Snugger (right)

SPECIAL ITEM RACK (SOME MODELS)

The innovative design of the Special Item Rack allows you to store a six-pack of 12 ounce drink cans, a bottle of wine,

a two-liter soft drink bottle, or a carton of eggs. The Special

Item Rack mounts on the left side of your refrigerator. To install, just slide the Special Item Rack onto any shelf as

shown in the drawing.

ADJUSTABLE DOOR BINS

Some models have adjustable door bins that can be moved

to suit individual needs.

To move door bins

1. Lift bin straight up.

2. Remove bin.

3, Place bin in desired position.

4. Lower bin onto supports until locked in place.

Adjustable Door Bin

Special Item Rack

CRISPERS (SOME MODELS)

The crispers, located under the bottom refrigerator shelf, are designed for storing fruits, vegetables, and other fresh produce. Wash items in clear water and remove excess water before placing them in the crispers. Items with strong odors or high moisture content should be wrapped before storing.

Crisper Drawer

HUMIDITY CONTROL (SOME MODELS)

The Humidity Control, present on some models with crisper drawers, allows you to adjust the humidity within the crisper. This can extend the life of fresh vegetables that keep best

in high humidity.

DELl DRAWER (SOME MODELS)

Some models are equipped witha Dell Drawer for storage of

luncheon meats, spreads, cheeses, and other dell items.

Dell Drawer

WINE RACK (SOME MODELS) The Wine Rack stores bottles of wine, or single two-liter

plastic bottles of juice or soda pop. To install, slide the Wine Rack onto the shelf with the curve facing in. To remove,

slide the Wine Rack out. Install on either side of shelf.

NOTE: Leafy vegetables keep best when stored With the

Humidity Control set on High Humidity, or in a drawer without a Humidity Control. This keeps incoming air to a

minimum and maintains maximum moisture content.

Low

High

Humidih

Crisper Humidity Control

Wine Rack

Ice Service

If your refrigerator has an automatic ice maker, t will orovide a sufficient

supply of ice for normal use. During the initial startap of your refrigerator.

however, no ice will be produced during the first 24 hours ofoperation. Automatic ice makers are also optional accessories that may be installed in most models

at any time. Call your local dealer for information. TURNING YOUR ICE MAKER ON

After the plumbing connections have been completed, the water supply valve

must be opened. Place the ice container under the ice maker, pushing itas far back as possible. Lower the wire signal arm to its "down" or ON position. New plumbing connections may cause the first production of ice cubes to be

discolored or have an odd flavor. These first cubes should be discarded until the cubes produced are free of discoloration and taste.

TURNING YOUR ICE MAKER OFF

To stop the ice maker, lift the wire signal arm until it clicks and locks in the "up" or OFF position. The ice maker also tums off automatically when the ice container isfull. If you r model has an adjustable freezer shelf, place the shelf

in the lower position, so that the wire signal arm will hit the ice when the

container is full.

Ice Maker

Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected

to soft water, ensure that the softener is maintained and working properly.

ICE MAKER TIPS

Ice cubes stored too long may develop an odd flavor. Empty the ice container and ensure that the wire signal arm is inits "down" or ON position. The ice maker will then produce more ice.

Occasionally shake the ice container to keep ice separated.

Keep the wire signal arm in its "up" or OFF position until the refrigerator isconnected to the water supply or whenever

the water supply isturned off. The following sounds are normal when the ice maker is operating:

Motor running Ice loosening from tray

Ice dropping into ice container Running water

Water valve opening or closing

NOTE: F0r more information on these 0pe[ations, see Normal Operating Sounds and Sights section on Page i 7:

DO Not place the ice container in your dishwasher,

Wash the ice container in warm water with mild detergent. Rinse well and dry. Stop the ice maker when cleaning the freezer and during vacations.

If the ice maker will be turned off for a long period of time, turn the water supply valve to the closed position.

Food Storage&Energy Saving Ideas

FOOD STORAGE IDEAS

Fresh Food Storage

The fresh food compartment should be kept between 34° Fand 40 ° F with an optimum temperature of 37 ° F. Avoid overcrowding the refrigerator shelves. This reduces the circulation of air around the food and results in uneven cooling.

Fruits and Vegetables

Storage inthe crisper drawers traps moisture to help preserve the fruit and vegetable quality for longertime periods.

Meat

Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or surfaces does not

Occur.

Frozen Food Storage

The freezer compartment should be kept at 0° F or lower. A freezer operates most efficiently when it is at least 2/3 full.

Packaging Foods for Freezing

To minimize dehyd ration and quality deterioration, use aluminum foil, freezer wrap, freezer bags or airtight containers.

Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out,

change color, and develop an off-flavor (freezer burn). Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.

Do not refreeze meat that has completely thawed.

Loading the Freezer

Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing, and can raise the temperature of frozen foods.

Leave a space between the packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.

Avoid storing hard-to-freeze foods such as ice cream and orange juice on the freezer door shelves. These foods are

best stored in the freezer interior where the temperature varies less.

ENERGY SAVING IDEAS

Locate the refrigerator in the coolest part of the room, out of direct sunlight,

and away from heating ducts or registers. Do not place the refrigerator

next to heat-producing appliances such as a range, oven, or dishwasher. If this is not possible, asection of cabinetry or an added layer of insulation between the two appliances will help the refrigerator operate more

efficiently.

Level the refrigerator so that the doors close tightly.

• Refer to this Use & Care Manual for the suggested temperature control settings.

• Periodic cleaning of the condenser will help the refrigerator run more efficiently. See the Care and Cleaning Chart on page 18.

Do not overcrowd the refrigerator or block cold air vents. Doing so causes

the refrigerator to run longer and use more energy.

Cover foods and wipe containers dry before placing them in the refrigerator. This cuts down on moisture build-up inside the unit.

Organize the refrigerator to reduce door openings. Remove as many items as needed at one time and close the door as soon as possible.

UNDERSTANDING THE SOUNDS YOU MAY HEAR

Your new high-efficiency refrigerator may make unfamiliar sounds. Don't be alarmed, these are all normal sounds. Hard

surfaces, such as vinyl or wood floors, walls, and kitchen cabinets may make sounds more noticeable. Listed below are descriptions of some of the most common sounds you

may hear, and what is causing them.

NOTE: Rigid foam insulation is Very energy efficient,

but is not a sound insulator.

A. Evaporator

The flow of refrigerant through the evaporator may create a boiling or gurgling sound.

B. Evaporator Fan

You may hear air being forced through the refrigerator by the evaporator fan.

C. Defrost Heater

During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After defrosting, a popping sound may occur.

IMPORTANT: During the automatic defrost cycle, you may notice a red glow in the vents on the back wall of

your freezer compartment, This is norma! during the

defrost cycle.

D. Automatic Ice Maker

If your refrigerator isequipped withan automatic ice maker, you will hear ice cubes falling into the ice bin.

E. Cold Control & Defrost Timer

These parts can produce a snapping or clicking sound when turning the refrigerator on and off. The timer also produces sounds similar to an electric clock.

F. Condenser Fan

If condenser coils are located underneath your refrigerator as shown in the drawing at the left, you have a condenser fan. You may hear air being forced through the condenser by the condenser fan.

G. Compressor

Modern, high-efficiency compressors operate much faster than older models. The compressor may have a high-pitched hum or pulsating sound.

H. Water Valve

If your refrigerator is equipped with an automatic ice maker, you will hear a buzzing sound as the water valve

opens to fill the ice maker during each cycle.

L Drain Pan (Nonremovable)

You may hear water running into the drain pan during the defrost cycle. The drain pan will be located on top of the compressor for air-cooled condensers (black coils on back of refrigerator).

J. Condenser Coils (Fan-cooled models only)

Keepyourrefrigeratorandfreezercleantopreventodorbuild-up.Wipeupanyspillsimmediatelyandcleanbothsectionsat leasttwicea year.Neverusemetallicscouringpads,brushes,abrasivecleanersorstrongalkalinesolutionsonany

surface.Do not wash any removable parts in a dishwasher. Always unplug the electricalpower cord from the wall

outlet before cleaning.

When moving the refrigerator, pull straight out. Do not shift the refrigerator from side to side as this may

tear or gouge the floor covering. Ifthe refrigerator has an automatic ice maker, be careful not to move the

refrigerator beyond the plumbing connections. Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp hands.

To avoid damage and help the refrigerator run as efficiently as possible, clean the condenser periodically.

NOTES:

Turning the refrigerator temperature control to "0" turns off the compressor, but does not disconnect electrical power to the light bulb or other electrical components.

Do not use razor blades or other sharp instruments which can scratch the appliance surface when removing

adhesive labels. Any glue left from tape or labels can be removed with a mixture of warm water and mild detergent, or. touch the glue residue with the sticky side of tape you have already removed. Do not remove the

serial plate.

Care & Cleaning Chart

Part

Interior/Door Liner

Door Gaskets Drawers/Bins

Glass Shelves

Toe Grille

Exterior and Handles

(Stainless Steel

Models Only)

Condenser Coils

(Fan-cooled models only)

Condenser Coils

(Air-cooled models only)

Defrost Water Soap and water Pan

What To Use Tips and Precautions

Soap and water Baking soda and water

Soap and water Soap and water

Soap and water Glass cleaner

Mild liquid sprays Soap and water Mild liquid sprays

Vacuum attachment Soap and water

Soap and water Ammonia

Stainless Steel Cleaners

Condenser Cleaning Brush is available from

your dealer. Vacuum Cleaner

Vacuum Cleaner

Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to wring

excess water out of sponge or cloth before cleaning around controls,

light bulb or any electrical part.

Wipe gaskets with a clean soft cloth.

De not wash any removable items (bins, drawers, etc.) in dishwasher.

Allow glass to warm to room temperature before immersing in warm water.

Vacuum dust from front of toe grille. Remove toe grille (Bee illustration on

page 4). Vacuum backside and wipe with sudsy cloth or sponge. Rinse and

dry.

Do not use commercial household cleaners, ammonia, or alcohol to clean

handles. Clean stainless steel front and handles with non-abrasive soapy water and a

dishcloth. Rinse with clean water and a soft cloth. Wipe stubborn spots with an ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless steel

cleaner. These cleaners can be purchased at most home improvement or major department stores. Always follow manufacturer's instructions.

NOTE: Always clean, wipe and dry with the grain to prevent cross-grain scratching. Wash the rest of the cabinet with warm water and mild liquid detergent. Rinse well, and wipe dry with a clean soft cloth.

No need to clean unless operating refrigerator under particularly dusty or greasy conditions, or if there is significant pet traffic in your home. If cleaning

is necessary, remove toe grille and use extended vacuum attachment and condenser cleaning brush to remove dust build-up from condenser coils (see item "J" in illustration on page 17 for location).

Use the dusting tool attachment on your vacuum to remove dust build-up on the condenser coils (black tubes and wires) attached to the back of air-cooled refrigerators only.

Some models have defrost water pan located on top of compressor at bottom rear of refrigerator (see illustration on next page). Wipe water pan with damp

cloth. NOTE: The defrost water pan is NOT removable.

NEVER CLEAN CONDENSER (SOME MODELS)

Ifyour refrigerator isequipped with a Never Clean condenser, there's no need to cleanthe condenser under normal operating conditions. If the refrigerator is operated under particularly dusty or greasy conditions, or ifthere issignificant pet traffic

inyour home, itmay be necessary to periodically clean the condenser for maximum efficiency.

_Av0id cuts when replacing lightbulbs,

wear gloves.

REPLACING THE FREEZER LIGHT BULB (SOMEMODELS)

1. Unplug refrigerator.

2. Wear gloves as protection against possible broken glass.

3. Unsnap light shield as shown.

4. Unscrew and replace old bulb with an appliance bulb of the same wattage.

5. Replace light shield.

6. Remember [o ;)lugthe refrigerator back in.

Defrost Water Pan (some models_

Vacation and Moving Tips

Short

Vacations

Long • Turn off automatic ice maker and turn water supply valve to closed position.

Vacations • Clean interior thoroughly.

Moving

• Leave refrigerator operating during vacations of 3 weeks or less.

• Use all perishable items from refrigerator compartment.

• Turn automatic ice maker off, even if you will only be gone for a few days.

• Remove all food and ice if you will be gone one month or more.

• Turn controls to "0" and disconnect power.

• Leave both doors open to prevent odors and mold build-up. Block doors open if necessary.

• Remove all food and ice.

• If using handcart, load from side.

• Adjust rollers all the way up to protect them during sliding or moving.

• Pad cabinet to avoid scratching surface.

REFRIGERATOR WARRANTY

Your refrigerator is protected by this warranty

WARRANTY THROUGHOURAUTHORIZEDSERVICERS, THECONSUMERWILLBERESPONSIBLEFOR:

PERIOD WEWILL:

FULLONE-YEAR Or_eyearfrom beginal Payallcosts for repairingorreplacinganypartsofthis Costs of service calls that are listed under NORMAL WARRANTY purchasedate appliancewhichprove to be defectivein materialsor RESPONSIBILITIESOFTHECONSUMER.*

LIMITED2NO'STH Secondthroughfifth Repairor replaceanypartsinthe cabinetlineror Costsforpickupand deliveryof theappliancerequiredbecause YEARWARRANTY yearsfromodginal SealedRefrigerationSystem(compressor,condenser, d service Costsforlabor,partsandtransportationotherthan (Cabinet Liner and purchasedate evaporator,dnerandtubing)whichproveto be with respectto thecabinetlineror SealedRefrigerationSystem

SealedSystem) defectiveinmaterialsorworkmanship LIMITED Timeperiodslisted All of theprovisionsofthefullwarrantiesaboveand Costsofthetechnidart'straveltothe homeandanycostsfor

WARRANTY above theexclusionslistedbelowapply pickup anddeliveryoftheappliancerequiredbecauseof (Applicable to the service

StateofAlaska)

In the U.S.A., your appliance is warranted by Eiectrolux Home Products North America, a division of White Consolidated Industries inc. We

authorize no person to change or add to any of our obiigations under this warranty. Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux Home Products North Amenca servicer. In Canada, your appliance is warranted by WCl Canada Inc.

*NORMAL

RESPONSIBILITIES

OF THE CONSUMER

EXCLUSIONS

IF YOU NEED SERVICE

This warranty applies only to products in ordinary household use, and the consumer is responsible for the

items listed below:

1. Proper use of the appliance in accordance with instructions provided with the product.

2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance with all local plumbing, electdcal and/or gas codes.

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house widng.

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,etc., which are not a part of the appliance when it was shipped from the factory.

5. Damages to finish after installation.

6. Replacement of light bulbs aod/or fluorescent tubes (on models with these features).

This warranty does not cover the following:

1. CONSEQUENTIAL OR iNCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.

NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.

2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary household use. The consumer shall pay for such service calls.

3. Damages caused by services performed by servicers other than Electrolux Home Products North America or its authorized servicers; use of parts other than genuine Electrolux Home Products parts; obtained from persons

other than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty period should service be required, if service is performed, it is in your best interest to obtain and keep all

receipts. This written warranty gives you specific legal dghts. You may also have other rights that vary from state to state. Service under this warranty must be obtained by contacting Eiectrolux Home Products:

workmanship Excludesoriginal andreplacementice & Waterfilter cartridges(if equipped) Originaland

replacement cartridges are warranted for 30 days (pads only)

This warranty only applies in the 50 states of the U.S.A., Puerto Rico, and Canada. Product features or specifications as desodbed or illustrated are subject to change without notice. All warranties are made by Electrolux Home Products North America, a division of White Consolidated

Industries Inc. In Canada, your appliance is warranted by WCl Canada Inc.

01-U-RE-g2 (Rev. 12/2000)

USA 800°944°9044

Electrolux Home Products North America P.O. Box 212378

Augusta, GA 30917

Electrolux Home Products North America

6150 McLaughlin Road

Mississauga, Ontario

Canada

866°213o9397

L5R 4C2

+ 44 hidden pages