Frigidaire FEB30S5ASB, GLMB209D, MWTRMKT27B, MWTRMKT30B, MWTRMKT27S Installation Instructions Manual
...
Installation
Built-in Trim Kit
Instructions
BEFORE YOU BEGIN
• IMPORTANT – Save these instructions
for local inspector's use.
• IMPORTANT – Observe all governing
codes and coordinates.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
•
Note to Consumer – Keep these
instructions for future reference.
• Skill level - Installation of this appliance requires
basic mechanical and electrical skills.
FOR YOUR SAFETY:
WARNING – Before beginning the installation,
switch power off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
MWTRMKT27 and MWTRMKT30
Read
these instructions completely and carefully.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
• Unplug the microwave oven before attempting
installation of this kit.
• Because the kit includes metal parts, caution
should be used in handling and installation to
avoid the possibility of injury.
• Do not remove permanently affixed labels, warn-
ings, or plates from the product. This may void
the warranty.
IMPORTANT - PLEASE READ
AND FOLLOW
THIS BUILT-IN KIT IS DESIGNED FOR USE ONLY
WITH ELETROLUX MICROWAVE OVENS SPECIFYING BUILT-IN KIT
MWTRMKT27 OR MWTRMKT30 ON THE RATING
LABEL ON THE LEFT SIDE WALL OF THE
MICROWAVE OVEN CAVITY.
QUESTIONS?
For customers in the United States call: 1-800-944-9044
For customers in Canada call: 1-800-213-9397 (English)
1-800-668-4606 ext.8199 (French)
Visit our Website at: www.frigidaire.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
1
p/n 316137235
TINSEB384MRR1
Installation Instructions
PARTS INCLUDED IN THE KIT
1. Front Frame Assembly - QTY 1
2. Exhaust Duct Assembly - QTY 1
3. Screw A - QTY 2
4. Screw B - QTY 4
CHOOSING A LOCATION FOR
YOUR MICROWAVE OVEN IF
BUILT-IN
Your microwave oven can be built into a cabinet or wall
by itself or above the wall oven listed below-using:
Model# Built-in-Kit 27” Built-in-Kit 30”
GLMB209DB MWTRMKT27B MWTRMKT30B
GLMB209DS MWTRMKT27S MWTRMKT30S
GLMB209DQ MWTRMKT27Q MWTRMKT30Q
PLMB209DC MWTRMKT27C MWTRMKT30C
CPLMB209DC MWTRMKT27C MWTRMKT30C
Front Frame Assembly
Exhaust Duct Assembly
Screw A
Screw B
Lower Oven: FEB27AS/B, GLEB27SCS/B,
PLEB27S8CC, GLEB30S8CS/B/Q, FEB30S5AS/B,
PLEB30S8CC
Do not build-in above any other gas or electric wall
oven.
See Illustration 1 for proper location when building in
above the specified wall oven. Carefully follow both the
wall oven installation instructions and Electrolux’s Built-in
Kit instructions. Be sure that the clearance of the floor
between the wall oven and the microwave oven is minimum of 2 inches.
CABINET OR WALL CUTOUT
Cutout Dimensions
Height (A)
Minimum 16
Maximum 17” (43.2 cm)
Width (B)
Minimum 24
Maximum 24
Depth (C)
Minimum 20” (50.8 cm)
3
/4” (42.5 cm)
3
/8” (61.9 cm)
11
/16” (62.7 cm)
2”
Illustration 1
2
Installation Instructions
6”
(15.2 cm)
4”
(10.2 cm)
Flanges
A
4”
(10.2 cm)
B
C
Screw A
Exhaust Duct
Assembly
Screw A
Illustration 2
ELECTRICAL OUTLET LOCATION
Outlet should NOT be in the shaded area as indicated on
Illustration 2
NOTE 1:
If the Depth (C) dimension is greater than 21” (53.3 cm),
the outlet location may be in any area on the rear wall.
NOTE 2:
The floor of the opening should be constructed of plywood strong enough to support the weight of the oven
and floor load (approximately 100 pounds). The floor
should be level for proper operation of the oven. Be sure
to check the local building code as it may require that the
opening be enclosed with side, ceiling and rear partition.
The proper functioning of the oven does not require the
enclosure.
Illustration 3
EXHAUST DUCT ASSEMBLY
1. Place the Exhaust Duct in the opening. When the
Exhaust Duct Assembly is in the opening correctly,
the flanges will be tightly against the lower edge of
the opening. See Illustration 3.
2. Secure the Exhaust Duct Assembly with the two
screws A.
IMPORTANT: Secure screws in outer hole.
3
Installation Instructions
FRAME INSTALLATION
1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet.
2. Carefully guide the assembled oven into the prepared opening. Slide the oven on the Exhaust Duct
Assembly. See Illustration 4. Avoid pinching the cord
between the oven and the wall. Adjust the position of
the oven so that the feet of the oven are fitted into the
recesses of the Exhaust Duct Assembly. See
Illustration 5.
3. Position the FRAME ASSEMBLY to be square with
the oven. Carefully place the FRAME ASSEMBLY
on the oven. Check that it is level and then secure
with two SCREWS B. See Illustration 6.
4. Secure the bottom portion of the FRAME ASSEMBLY with the two remaining SCREWS B. See
Illustration 6.
Screw B
Exhaust Duct Assembly
Illustration 5
Foot
Recess
Illustration 4
Screw B
Screw B
Screw B
Illustration 6
4
Loading...