Frigidaire FGC36S5ECA, GLGC36S8EBA, GLGC36S8EQA, GLGC36S8ESA, LEGC30S9FEA Installation Guide

...

INSTALLATION AND SERVICE MUST BE PERFORMED BY

A QUAUHED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

If the information in this manual is not followed exactly, a fire or explosion may result ]

causing property damage, personal injury or death. FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

J WHAT TO DO [F YOU SMELL GAS:

® Do not try to light any appliance.

• Do not touch any e[ectrka[ switch; do not use any phone in your building. immediately ca[[ your gas supplier from a neighbor's phone. Follow the gas suppHer's instructions.

If you cannot reach your gas supplier, calmthe fire department.

-- installation and service must be performed by a qualified installer, service agency or the gas supplier.

Cooktop Dimensions

* 30" min. for unprotected cabinet

24" min. for protected surface

. LENGTH .

30" Models 30 (76.2) 21 Y2(54.6) 2!4 (7,0)

36" X 21Yz"Models 36 (91.4) 21 Y2(54.6) 2sA (7,0)

Cooktop Cutout Dimensions

Figure 1

MIN. DILENGTH MAX}

26 s/s (67.6) 267/s (68.3)

32 34(83.2) 33 (83.8)

MIN. E.WIDTH MAX.

19 (48.3) 19 s/s(49.2)

30" Min.*

(76.2 cm) Min.*

COOKTOP* (Min.) , (Min.)

5 (12.7) 2s4(7) 2Y4(5.7)

5 (12.7) 23A(7) 2Y4(5.7)

36"X 18" Models 36 (91.4) 18 (45.7) 2!4 (7,0)

All dimensions are in inches (cm).

Dimension F is for clearance under cooktop for gas connection. NOTE: Wiring diagrams for these appliances are enclosed in this booklet. Only some models are available in Canada.

Printed in United States

34 ¼ (87) 34 s/s(87.3)

16 s/s(42.2) 16 34(42.5)

5 (12.7) 4Y4(10.8) 3 (7.6)

P/N 318201463 (0508) Rev A

English - pages 1-8

Espanol- pages 9-17

Fran_ais - pages 18-26

Wiring Diagrams - pages 27-28

!3" (33 cm)

Max, Depth For

Cabinet Installed Above Cooktop.

A Min.

30" (76.2 cm) Min, Clearance Between

the Top of the

Cooking Platform

-------_-- and Unprotected Wood or Metal

Cabinet

Dimension K isthe

Minimum Clearance

Required From Left

Side To Adjacent

Combustible Surfac.e.

18" Min.

(45.7cm Min.)

24" (61 cm)

Dimensions J is the Minimum

Distance Required Between Rear

of Cooktop to Adjacent

Combustible Surfaces.

Clearance

Dimension H istile

Minimum Clearance

Required From Right

Side To Adjacent

Combustible Surface.

To eliminate the risk of

burns or fire by reaching over heated surfaces, cabinet storage space located above the cooktop should be avoided. If (.abinet storage is provided, risk (an be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of tile

cabinets.

Figure 2 - COUNTERTOP CUTOUT OPENING

30" Models 4" (10.2 crn) 1 _/_"(3.8 cm) 7" (17.8 cm)

36" X 21_/_" Models 5" (12.7 cm) 1 _/_"(3.8 cm) 5" (12.7 cm)

36" X 18" Models 3" (7.6 cm) 3 3A" (9.5 cm) 3" (7.6 crn)

Important Notes to the Installer

1. Readallinstructionscontainedintheseinstallation instructionsbeforeinstallingthecooktop.

2. Removeallpackingmaterialbeforeconnectingtile electricalsupplytothecooktop.

3. Observeallgoverning(:odesandordinances.

4. Besuretoleavetheseinstructionswithtileconsumer.

important Note to the Consumer KeeptheseinstructionswithyourUseandCare Guide for

future reference.

IMPORTANT SAFETY

IN<

Installation of this cooktop must conform with local codes or, in the absence of local (:odes, with tile National Fuel

Gas Code ANSI Z223.1--1atest edition in the United States, or in Canada, with the Canadian Fuel Gas Code,

CAN/CGA B149 and CAN/CGA B149.2.

This cooktop has been design certified by American Gas Association (A.G.A.). As with any appliance using gas and generating heat, there are certain safety precautions you should follow. You will find them in tile Use and Care Guide, read it carefully.

Be sure your cooktop is installed and grounded

properly by a qualified installer or service technician.

• This cooktop must be electrically grounded in

accordance with local codes or, in their absence, with the National Electrical Code ANSI/NFPA No.

70--latest edition in the United States, or in Canada, with the Canadian Electrical Code, CSA

C22.1 Part 1.

• The burners can be tit manuaIiy during an

electrical power outage. To light a burner, hold a tit match to the burner head, then slowly turn the

Surface Control knob to UTE. Use caution when tighting burners manually.

• Do not store items of interest to children in the

cabinets above the cooktop° Children could be seriously burned climbing on the cooktop to reach

items.

• To eliminate the need to reach over the surface

burners, cabinet storage space above the burners should be avoided.

Adjust surface burner flame size so it does not

extend beyond the edge of the cooking utensil.

Excessiveflame is hazardous.

Never use your cooktop for warming or heating the room. Prolonged use of the cooktop without adequate ventilation can be hazardous.

• Do not store or use gasoIine or other flammable vapors and liquids near this or any other appliance. Explosions or fires could result.

The electrical power to the cooktop

must be shut off while line connections are being made. Failure to do so could result in serious

injury or death.

1. Before Installing the Cooktop

Foam Tape

Figure 3

A roll of foam tape is supplied loose and packed in tile literature package. Install the foam around the perimeter of the flange of the burner box, at a distance of _/4"(0.6 cm) from the edge of the glass or porcelain top. Apply the exposed adhesive side of the tape against the underside of the glass or the burner box surface (see figure 3).

NOTE: This tape sealsthe underside of the cooktop to the counter. Do not remove this foam tape. This tape prevents entry of air for normal gas combustion, and prevents liquids from leaking under the cooktop.

After inserting the cooktop into the countertop opening, make sure the unit is sitting on the metal flange around the top of the burner box. Cooktop must not sit on the glass or porcelain top. Avoid cutting an oversized hole in the countertop.

All mounting hardware

must be used to secure

the built-in oven to the

cabinets. Refer to the builtqn oven installa-

tion instructions.

208/240 Volt grounded

junction box for built-in

oven.

This cooktop may be im stalled over certain built-

in electric oven models.

Approx. 3"

(7.6 cm)

Side filler panels are necessaryto isolate the unit from adjoining cabinets. Panelheight should allow for installation of approved cooktop models. See "Typical Gas Cooktop Im

stallation Over an Electric Builtqn Oven Installed Under the Counter" in this booklet.

32" Min.** (81.3 cm Min.**)

36" Min. /_ (91.4 cm Min.)

Use sA" (1.9 cm) plywood, installed on two runners, flush with toe plate. Must be capable of supporting 150 Ibs (68 kg).

4 Y2" Max.*

* If no cooktop is installed directly over

the oven unit, 5" (!2.7 cm) maximum

isallowed.

** 32" (8! .3 cm) rain. from top of cabinet

to top of runners must be maintained.

Figure 4 - TYPICAL UNDER COUNTER INSTALLATION OF AN ELECTRIC BUILT-IN OVEN

Cut an opening in wood base mini-

mum 9" x 9" (22.9 cm X 22.9 cm),

2" (5.1 cm) from left side filler

panel, to route armoured cable to

junction box.

(11.4 cm Max.*)

CUTOUT DIMENSIONS

MODEL' E. HEIGHT I F.WIDTH' G. DEPTH

27" (68.6 cm) 28 I/8" (71.4 cm) Min. 247Is" (63.2 cm) Min.

Wall Oven 28 sis" (72.7 cm) Max. 25 Y4" (64.1 cm) Max.

30" (76.2 cm) 28 X" (71.8 cm) Min. 28 Vz" (72.4 cm) Min.

Wall Oven 28qs" (713.3cm) Max. 29" (713.7cm) Max.

WITH COOKTOP MOUNTED ABOVE

23 YZ'(59.7 cm)

24" (61 cm)

18" Max.

(45.7 cm)

Wall Oven Cabinet

Figure 5 - TYPICAL GAS COOKTOP INSTALLATION OVER

AN ELECTRICBUILT-IN OVEN INSTALLED UNDER THE COUNTER

2. Wall Outlet Location

j_30.5 cm) --_

Cabinet sides or

filler panel

5" Max. 6 Y2" Min.

Flare (1271cm) (I_5_:m)

Flare

Union

3. Cramp Down Information

Once the cooktop is installed in the counter opening, you must clamp the unit down as shown.

Pressure Regulator

120V/6OHz

Grounded

Outlet

Manual

Shutoff

Valve

4" (;0.2 cm)

Right Side of

Cabinet

(To be

accessible for shut-off valve

operation)

Countertop

NOTE: Ifan outlet

is not available, have one installed

by a qualified

technician.

8" _ni[

10" (25.4 cm)

120V grounded outlet on

rear wall

CL of unit

"CLof unit

Figure 6

22"

(55.9 cm)

Figure 7

To clamp down, insert the bracket with the offset side of the angle into the slots on each side of the unit. The thumb screw should then be run through the bracket, up against the bottom of the counter. Tighten until the unit

draws down.

4. Provide an Adequate Gas Supply

This cooktop is designed to operate on natural gas at 4" (10.2 cm)of manifold pressure only.

A pressure regulator is connected in series with the manifold on tile cooktop and must remain in series with

tile supply line.

For proper operation, tile maximum inlet pressure to the regulator must be no mere than 14" (35.6 cm) of

water column (W.C.) pressure.

For checking the regulator, the inlet pressure must be at least 1" (2.5 cm) (or 2.5 kPa) greater than the regulator

manifold pressure setting. The regulator isset for 4" (10.2 cm) of manifold pressure, tile inlet pressure must

be at least 5" (12.7 cm).

The gas supply line to the cooktop should be Y2" (1.3 cm) or sA" (7.9 cm) pipe.

5. LPiPropane Gas Conversion

This appliance carl be used with Natural gas or LP/ Propane gas. It is shipped from the factory for use with natural gas.

If you wish to convert your cooktop for use with LP/ Propane gas, use the supplied fixed orifices in tile package containing tile installation Instructions Manual, in a bag marked "FOR LP/PROPANEGAS CONVERSION". Follow the installation instructions packaged with tile

orifices.

5. Install Pressure Regulator

Install the pressure regulator with the arrow on the regulator pointing up toward the unit in a position where

yOUcan reach the access cap.

FIRE HAZARD. Do not make the

connection too tight. The regulator is die cast. Overtightening may crack the regulator resulting in a gas

leak and possible fire or explosion.

Manual GAZFLOW Pressure Shutoff Flare _ Flare Regulator

Valve Union Union _,

t @

Ont

"_ Flexible Connector

Off

All connections must be wrench-tightened

Figure 8

Assemble the flexible connector from the gas supply pipe to the pressure regulator in order: 1- manual shutoff valve, 2- _/2" nipple, 3- _/2"flare union adapter, 4- flexible connector, 5- _/2" flare union adapter, 6- _/2"

nipple, pressure regulator.

Use pipe-joint compound made for use with Natural and LP/Propane gas to seal all gas connections. If flexible

connectors are used, be certain connectors are not

kinked.

The conversion must be performed by a qualified service technician in accordance with the manufacturer's

instructions and all local codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. Tile qualified agency performing this work assumes responsibility for the conversion.

Failure to make the appropriate

conversion can result in personal injury and property damage.

Important: Remove all packing material and

literature from cooktop before connecting gas and electrical supply to cooktop.

The supply line should be equipped with an approved shutoff valve. This valve should be located in the same

room as tile cooktop and should be in a location that allows ease of opening and closing. Do not block access to the shutoff valve. The valve is for turning on or shutting off gas to the appliance.

To Appliance

Shutoff Valve

Figure 9

Open the shutoff valve in tile gas supply line. Wait a few minutes for gas to move through the gas line.

To gas supply line

Checkfor leaks. Leaktestingoftheapplianceshallbe conductedaccordingtothemanufacturer'sinstructions. Afterconnectingthecooktoptothegassupply,check tile systemforleakswithamanometer.Ifa manometer

isnotavailable,turnonthegassupplyandusealiquid leakdetector(orsoapandwater)atalljointsand

connectionstocheckforleaks.

Donotuseaflameto checkforleaks

fromgasconnections.Checkingforleakswithaflame

mayresultinafireorexplosion.

Tightena[[connectionsif necessaryto preventgas

leakageinthecooktoporsupplyline.

Checkalignmentofvalvesafterconnectingthe cooktoptothegassupplytobesurethecooktop

manifoldpipehasnotbeenmoved.

Preferred Method

Grounding type wall receptacle Power supply cord with

3-prong grounding plug

Figure 10

Where a standard 2-prong wall receptacle is installed, it is the personal responsibility and obligation of the consumer to have it replaced by a properly grounded 3- prong wall receptacle.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

Disconnectthiscooktopandits individualshutoff

valvefromtilegassupplypipingsystemduringany

pressuretestingofthatsystemattestpressuresgreater

thanY2psig(3.5kPaor14"(35.6cm)watercolumn). Isolatethecooktopfrom thegassupplypiping

systembyclosingitsindividualmanualshutoffvalve duringanypressuretestingoftilegassupplypiping systemattestpressuresequaltoor lessthanY2psig (3.5kPaor 14"(35.6cm)watercolumn).

7. Connect Electridty to Gas Cooktop

Electrical Requirements

120 volt, 60 Hertz, properly grounded branch circuit protected by a 15 amp circuit breaker or time delay fuse. Do not use an extension cord with this cooktop.

Grounding Instructions

IMPORTANT Please read carefully.

For personal safety, this appliance must be properly

grounded.

Tile power cord of this appliance is equipped with a 3-

prong (grounding) plug which mates with a standard 3- prong grounding wall receptacle (see Figure 8) to minimize the possibility of electric shock hazard from the

appliance.

Disconnect electrical supply cord from

wall receptacle before servicing cooktop.

8. Check Operation

Refer to the Use and Care Guide packaged with the cooktop for operating instructions and for care and cleaning of your cooktop.

Do not touch the burners. They may be hot enough to cause burns.

1. Install Burner Caps This cooktop is equipped with sealed burners as shown (see Figure 11).

Burner Cap_

Burner Base---_ (_

Burner Pan

Built-in)

Gas Opening

The wall receptacle and circuit should be checked by a qualified electrician to make sure the receptacle is

properly grounded.

Electrode -_/

Figure 11

A. Unpackburnerbasesandcaps.

B. Placeburnerbaseovereachgasopeningtube.

C. Makesuretheburnerisproperlyalignedand

leveled.Placeburnercapovereachburner base.

NOTE:Therearenoburneradjustmentsnecessaryon thiscooktop.

2. Turn on Electrical Power and Open Main Shutoff

Gas Valve

Check the Igniters Operation of electric igniters should be checked after cooktop and supply line connectors have been carefully checked for leaks and the cooktop has

been connected to electric power.

To operate the surface burner: A. Push in and turn a surface burner knob to the

LITE position. You will hear a little ticking noise; this isthe sound of tile electric ignitor which lights the burner.

B. After the burner lights, turn to the desired flame

size. The controls do not have to be set ata particular mark. Use the marks as a guide and

adjust the flame as needed.

Adjust the "LO" or "SIMMER" Setting of Surface

Burner Valves (see Figure 12) Push in and turn each control knob to the "LO" (or "SIMMER") setting. The "LO" setting of each burner has been set at the factory to the lowest

setting available to provide reliable reignition of the

burner. If it does not stay lit on the"LO" setting,

check the setting as follows.

A. Allow cooktop to cool to room temperature. B. Light all burners by turning each control knob to

LITEuntil burners ignite, and then set them at "Hi".

C. _turn the knob to tile LOWESTPOSITION. D. If burner goes out, readjust valve as follows;

Remove the surface burner control knob, insert a

thin-bladed screw driver into tile hollow valve stem and engage the slotted screw inside.

Flame size can be increased or decreased with

the turn of the screw. Adjust flame until you can quickly turn knob from HI to LOWEST

POSITIONwithout extinguishing the flame. Flame should be as small as possible without

going out.

E. If you need to adjust another burner, repeat the

steps from A to D above until all burners operate

properly.

When All Hookups are Complete

Make sure all controls are left in tile OFF position.

Make sure the flow of combustion and ventilation air to

the cooktop is unobstructed.

Model and Serial Number Location

Tile serial plate is located on the underside of the cooktop.

When ordering parts for or making inquires about your

range, always be sure to include the model and serial numbers and a lot number or letter from tile serial plate

of your cooktop.

Your serial plate also tells you the rating of tile burners, the type of fuel and the pressure the cooktop was adjusted for when it left the factory.

Hollow Valve

System

Before You Call for Service

Read tile Avoid Service Checklist and operating instructions in your Use and Care Guide.

\ /

Check to make sure the house fuse or circuit breaker for your cooktop are not blown or open.

Figure 12

LA INSTALAQ6N Y EL SERVIQO DEBEN SER REAUZADOS POR UN

INSTALADOR CAUNCADO.

IMPORTANTE: GUARDE ESTAS [NSTRUCQONES PARA USO DEL

INSPECTOR ELECTRICO LOCAL.

LEA Y GUARDE ESTAS INSTRUCQONES PARA FUTURAS REFERENQA

Si todas [as [nstrucdones de _ste manual no son observadas a [a [etra, se puede ocurr[r 1

[ncendios o exp[osiones que pueden causar daffos materia[es, [esiones o [a muerte. PARA SUSEGURDAD:

-- No a[macene o uti[ice gaso[ina u otros vapores y [iquidos inf[amaMes cerca de este o cualquier otto artefacto.

-- QUE HACER S[ HAY FUGAS DEGAS

• No intente de encender ningun artefacto

No toque ningun interruptor electrico; no uti[ice ningun aparato t_mefonico en su edifido. Llame inmediatamente el abastecedor de gas desde el temefono de un vedno. Siga [as instrucdones del

abastecedor de gas.

En caso que no puede contactar el abastecedor de gas [lame a[ departamento de bomberos.

-- La instalaci6n y el servido t_lefonico deben set reamizados por un instamador caIificado, por un servido tecnico certificado o por e[ abastecedor de gas.

Dimensiones de la plancha de cocinar a gas

* 30" rain. para un armario protegido.

24" rain. para una superficie no

protegida.

30" Min.*

j B ..... (76.2 cm) Min.*

[

Dimensiones del hueco para la plancha de cocinar a gas

Figura 1

30" Models 30 (76.2) 21 Y2 (54.6) 2_'A (7.0) 26 s/s (67.6) 267Is (68.3) 19 (48.3) 19 s/s (49.2) 5 (12.7) 23A (7) 2¼ (5.7)

36" X 21V2" Mz_dels 36 (91.4) 21 1/2(54.6) 2SA (7,0) 32 3A(83.2) 33 (83.8) 19 (48.3) 19 Sis (49.2) 5 (12.7) 23A (7) 2¼ (5.7)

36"X 18" Models 36 (91.4) 18 (45.7) 2SA (7,0) 34 ¼ (87) 34 s/s(87.3) 16 S/s (42.2) 16 3A (42.5) 5 (12.7) 4¼ (10.8) 3 (7.6)

Todas las dimensiones se dan en pulgadas (cm), La dimensi6n Feste pot debajo de [a plancha de cocinar para [a conexi6n de [a [inea de suministro de gas

NOTA: Se adiunta los diagramas de cables de esta plancha de cocinar con el [ibreta. PIN 318201463 (0508) Rev A Solamente algunos modelos est_in disponib[es en Canada1, English - pag_s 1-8

Imprimido en los Estados Unidos Espa¢_ol- pages 9-17

Diagrama de la instalaci6n al_mbrica - pages 27-28

Francais - pages 1g-26

+ 19 hidden pages