Frigidaire LAD704TDL3, LAD704TDL2, LAD704TDL1, LAD704TDL0, LAD504TDL7 Owner’s Manual

...

Download

ii!ii!iliiii!iiii ii_I:I_i_ i

Operating Instructions ..................

iiiiiiiii!i!ili!!li_!iiii!iiiii_iYiiiiiiiiiiii/Iiliiiiiiiiiii!ii

TAB

_a_%,............

www.frigidaire.com USA 1-800-944-9044 www.frigidaire.Ca Canada 1-800-265-8352

This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as instructed in this USE& CARE MANUAL. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution

must be practiced when installing, operating, and maintaining any appliance.

For Your Safety

, Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance. Read product labels for flammability and other warnings.

= Discard water from bucket. Water is not potable and cannot be used for drinking.

Grounding type wall receptacle

Child Safety Precautions

• Destroy the carton, plastic bags, and any packing materials immediately after the

dehumidifier is unpacked. Children should never use these items for play.

Do not leave children unattended in an area where the appliance is operating.

Power supply cord II

with 3-prong grounding

plug

Location

Electrical Information

• For your safety and protection, this dehumidifier is equipped with a three-prong grounding plug on the power cord. Do not, under any circumstances, cut or remove the round ground prong from the plug.

, Your dehumidifier must be plugged directly into a properly grounded and polarized

three-prong receptacle. If the wall receptacle you intend to use will not accept a three-prong plug, or if you are not sure the outlet is adequately grounded or protected

by a time delay fuse or circuit breaker, have a qualified electrician install the proper outlet according to the National Electrical Code and applicable local codes and ordinances. Do not

use an extension cord or an adapter plug.

° Never unplug the dehumidifier by pulling on the power cord. Always grip the plug firmly

and pull straight out from the receptacle.

• DOnot pinch, bend, or knot the power cord.

Selecting a Location

IMPORTANT:

1.Dehumidifiermust be operatedinan enclosedareato be most effective.Closealldoors, windows, and otheroutsideopeningsto theroom. The effectivenessofthe dehumidifier

depends on the rate at which new moisture-laden air enters the room.

2. Place dehumidifier in a location that does not restrict airflow through the front of the unit or out of the louvers on the left side of cabinet.

3. A dehumidifier operating in a basement will have little or no effect in drying an adjacent

enclosed storage area, such as a closet, unless there is adequate circulation of air in and out of the area. It may be necessary to install a second dehumidifier in the enclosed area for

satisfactory drying.

4. The dehumidifier must be installed on a level floor that will support it with a full bucket of water.

5. There should be a minimum of 12 inches clearance around the dehumidifier.

How It Works

When the unit is started, the fan begins to pull moisture-laden air across the dehumidifying coils. The coils condense or draw moisture from the air, and air flows through the side louvers into the

room as dry, warm air. Moisture removed from air is collected in a bucket on the front of the dehumidifier.

The unit is designed to operate between 41 °F (5 °C), and 96 °F(35 °C). The "Compressor" circuit has an automatic 3 minute time delayed start if the unit is turned off

and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping.

Make sure the tank is fitted correctly otherwise unit will not turn on.

Operating Instructions

Allow the unit to reach room temperature before operating,

To begin operating the dehumidifierr follow these steps:

Unit must be upright for one hour prior to operating.

1. Plug the power cord into a properly grounded 115 volt AC outlet. The POWER indicators will illuminate.

If the "BUCKET FULL" light is on, remove the bucket and re-install to reset the float switch.

humidity setting

bucket full

tO RH%

J_'tterreset

power

TIMER FAN SPEED v A FILTER

humidity

ON-OFF

2. To turn the unit on press the ON/OFF button. The unit will run in the factory setting of CONTINUOUS and high fan speed. In the Continuos Mode the unit will only display CO and not the room humidity. It is recommended you leave the unit

running in the CONTINUOUS setting for the first three or four days until the sweating and dampness odors have stopped.

[]

TIMER FAN SPEED v A FILTER ON-OFF

to RH% fitter reset

humidity setting

bucket full

power

humidity

Operating Instructions

(continued)

3. After a few days when the Relative Humidity has declined, press the HUMIDITY "_" or = buttons to choose a value between 35% to 85%, so the room is kept at a comfortable concentration. Pressing the 4- or ! buttons will

change the humidity selection in 5% increments. After you have set the desired humidity, the readout will display the actual room humidity. If at any time you want to return to the CONTINUOUS Mode, pressing the HUMIDITY

- button will lower the Relative Humidity through the 5% increments until the display reads CO.

humidity setting

I0 RH%

bucket full

filter reset

power

TIMER FAN SPEED v A FILTER

humidity

ON=OFF

4. You can also use the FAN button to change the fan speed to HIGH or LOW. The indicator light will show the setting you have selected. A higher fan speed will result in quicker moisture removal.

humidity setting

bucket full

[]

TIMER FAN SPEED v A FILTER ON-OFF

lO RH%

humidity

filter reset

power

5. The FILTER RESET light will illuminate after 250 hours of operation. At this time refer to the care and cleaning section to remove and clean the filter. Once the filter has been cleaned, to extinguish the light simply press the

FILTER button.

humidity setting

hi _ bucket full

[]

TIMER FAN SPEED v A FILTER

lo RH% filter reset

humidity

power

ON-OFF

Operating Instructions

(continued)

6. The TIMER function enables you to either Delay Start or Delay Stop the unit in the choice from 0.5 hour to 24 hours. If the unit is running then selecting Timer will turn the unit off after setting hours (Delay Stop). If the unit is off then

selecting Timer will turn the unit on after setting hours (Delay Start).

TIMER setting: First press TIMER button,then to adjust timer setting, tap or hold the _1- or m button to change the delay timer at 0.5 hour increments,up to 10 hours, then by 1 hour increments up to 24 hours. The control will count down the time remaining (8,7.5J, etc.) until the unit either starts or stops. For the Delay Start, the fan speed and humidity maintained will be the same as previously setting. After TIMER setting finishs, pressing TIMER button again

at any time will cancel the TIMER function. The Delay Start/Stop Feature will work until the unit either starts ro stops. Once that happens the above steps have to be repeated again.

1. Before entering TIMER setting, the power indicator must be lit to make sure power is being supplied to the unit.

2. Before entering TIMER setting, make sure first pressing HUMIDITY 4" or ! button sets one desired room humidity.

humidity setting

bucket full

10 RH%

jS"lterreset

power

TIMER FILTER ON-OFF

FAN SPEED v A

humidity

7. To shut the unit down, press the ON/OFF button.

While the unit is plugged in the power indicator will remain lit. Only removing the plug will extinguish this light.

humidity setting

bucketfull

TIMER FAN SPEED v A FILTER ON-OFF

10 RH%

humidity

j_'lter reset

power

Fault Codes

1. If the display reads "AS" or "ES", a sensor has failed. Contact your Authorized Frigidaire Service Center.

humidity setting

bucket full

TIMER FAN SPEED V A FILTER ON=OFF

[0 RH%

humidity

filter reset

power

Removing Collected Water

1. Emptying the Bucket: a. When the bucket is full the unit will shut down and the BUCKET FULL indicator light will illuminate.

humidity setting

[]

bucket full

lo RH%

filter reset

TIMER FAN SPEED v ^ FILTER

humidity

b. Do not move the unit at this point otherwise water may spill on the floor. c, Press sides of bucket gently to unclip the bucket from the unit. d, Remove the bucket as shown in the photographs below and empty the bucket.

Discard water from bucket, Water is not potable and cannot be used for drinking.

power

ON-OFF

e. Replace the empty bucket back into the unit and once seated correctly the unit will start up again. f. You should hear a click when the bucket is in the correct position

Removing Collected Water

(continued)

If the bucket full light does not extinguish, check that the float is correctly snapped in place

as indicated by the diagram.

2. Continuous Drainage:

a. For constant drainage operation, you will need a garden hose and a drain nearby to discharge the water into. b. Remove the bucket from the unit and set aside.

c. Lift up the side flap located on the right side of the unit as looking from the front. (fig.l) d. Insert the female threaded end of the hose through the opening. (fig.2)

e. Screw the garden hose onto the threaded portion of the tray underneath the bucket opening. (fig.3) f. Make sure the hose is secure so there are no leaks.

g. Direct the hose toward the drain, making sure that there are no kinks that will stop the water flowing. h. Place the end of the hose into the drain.

i. Place the bucket back in the unit and make sure that it is located correctly. (fig.4)

j. Select the desired humidity setting and fan speed on the unit for continuous draining to start.

i i::_ i

y '\c_

j j°"

==:_jj

::::::>_° i

fig. 1 fig. 2 fig. 3 fig. 4

If the unit stops operating check that the bucket full light is illuminated. If it is remove the bucket and empty the

contents and then check the seal between the hose and the drip tray. If there is a small leak then replace the hose gasket and re-tighten the hose.

ii!

Care And Cleaning

1. Filter a. Remove the filter every two weeks based on normal operating conditions.

b. To remove the filter, remove Bucket then pull filter downwards.

c. Wash the filter with clean water then dry. d. Re-install the filter, replace Bucket.

2. Cabinet a. Dust cabinet with an oil-free cloth, or using a damp cloth.

b. Vacuum grill using brush attachment.

3. Water Bucket a. Clean bucket with warm water and detergent.

Storage

When unit is not in use unplug and use the cord wrap shown for your model type.

' i ....

_ii ,,if

ii i,i'

ji' m'

1, 2,

Beforecallingforservice,reviewthislist.Itmaysaveyoutimeandexpense.Thislistincludescommonoccurrencesthatarenot

theresultofdefectiveworkmanshipormaterialsinthisappliance.

OCCURRENCE SOLUTION

DEHUMIDIFIER DOES NOT

OPERATE.

DEHUMIDIFIER RUNS TOO MUCH.

DEHUMIDIFIER IS OPERATING BUT ROOM IS NOT DRY ENOUGH.

Wall plug disconnected. Push plug firmly into wall outlet.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

The dryness level you selected has been reached. Dehumidifier automatically shuts off when selected amount of moisture has been removed from the air. tf you want to remove more moisture, Select

'CONTINUOUS _ by using the humidity button or knob. After the dehumidifier starts, reset the control to the desired setting.

Bucket not installed properly. See "Removing Collected Water".

Water in the bucket has reached its preset level. Dehumidifier automatically turns off when this occurs. Empty bucket and return bucket to position.

Dehumidifier is not turned on. Turn unit on.

"BUCKET FULL" light is on. Remove bucket, empty water and re-install correctly.

Windows or doors near dehumidifier are open to outdoors. Close all windows or doors to outside.

Area to be dehumidified is too large. Check with your dealer to see if capacity is adequate. Air movement through dehumidifier is blocked. Grill may be dirty. Use brush attachment of vacuum

cleaner to clean grill. See "Care and Cleaning". Dehumidifier must be placed in a space that does not restrict air flowing into the rear coil or out of the front grill.

Dehumidifier has been installed or restarted recently. The higher the moistuire in the room, the longer the dehumidifier will operate.

Dehumidifier is in the CONT mode and will remain on in this mode use the humidity button or knob to set a RH% higher level.

Humidity setting is too high. Press the HUMIDITY button or rotate knob to a lower setting or choose CONTINUOUS for maximum dryness.

Dehumidifier has been installed or restarted recently. The higher the moisture in the room air, the longer it takes for the room air to become dry.

Dehumidifier does not have sufficient clearance to operate. Air flow to front grill is blocked. See "Selecting a Location".

Room temperature is too low. Unit will not operate satisfactorily if the room temperature is below 41 °F(5 °C). See "Operating Conditions".

Refer to causes under DEHUMIDIFIER RUNS TOO MUCH.

FROST APPEARS ON COILS ABOVE BUCKET OR DRIP TRAY.

FAN NOISE.

Dehumidifier has been turned on recently. This is normal due to refrigerant rushing through the coil. Frost will usually disappear within 60 minutes.

Room Temperature is too low. All models will operate satisfactorily at temperatures greater than

41 °F (5 °C).

Air is moving through the dehumidifier. This is a normal sound.

If These Solutions Fail, Call :&-800-944-9044 For Frigidaire Service,

Your appliance is covered by a full one-year warranty and a limited 2-5 year warranty(sealed system). For one year from your

original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. From the second to the fifth year from your original purchase date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing) proves to be defective in materials or workmanship.

The consumer will be responsible for diagnostic costs and any removal, transportation and reinstallation costs which are required

because of service. Costs for labor, parts and transportation other than with respect to the Sealed Refrigeration System.

Exclusions

This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Product that has been transferred from its original owner to another party or removed outside the USA or Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased "as-is" are not covered by this warranty.

5. Food loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a part of the appliance when it is shipped from the factory.

10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors, cabinets, walls, etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUXSHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTYDAMAGE AND INCIDENTAL EXPENSES

RESULTING FROM ANY BREACHOF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATESAND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLYTO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

If You Need Service

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.

Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below.

This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.

Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under

this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described

or illustrated are subject to change without notice.

USA :1..800.944.9044 Electrolux Major Appliances

North America P.O. Box 212378

Augusta, GA 30907

Electrolux

1,800,265.83S2

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

Canada

L5V 3E4

Frigidaire LAD704TDL3, LAD704TDL2, LAD704TDL1, LAD704TDL0, LAD504TDL7 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual