Frigidaire GLTF1040AS Installation Instructions Manual

Installation

Instructions

Full Size Tumble Action Washers

Before beginning installation, carefully read these instructions. This will simplify the
installation and ensure the washer is installed correctly and safely . Leave these instructions
near the washer after installation for future reference.

NOTE: The electrical service to the washer must conform with local codes and ordinances
and the latest edition of the National Electrical Code, ANSI/NFPA 70 or in Canada, CSA
C22.1 Canadian Electrical Code Part 1.

Contents

For your safety the information in
this manual must be followed to minimize the
risk of fire or explosion or to prevent property
damage, personal injury or loss of life.

- Do not store or use gasoline or other

flammable vapors and liquid in the vicinity of
this or any other appliance.

- WHAT T O DO IF YOU SMELL GAS

· Do not try to light any appliance.

· Do not touch any electrical switch; do not

use any phone in your building.

· Clear the room, building or area of all
occupants.

· Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppliers
instructions.

· If you cannot reach your gas supplier, call
the fire department.

SUBJECT PAGE

Pre-Installation Requirements 2
Electrical Requirements 2
Grounding Requirements 2
Water Supply Requirements 2
Drain Requirements 2
Rough-In Dimensions 3
Location Of Y our W asher 4
Unpacking 4
Installation 5
Replacement Parts 5

Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.

Printed in U.S.A.

P/N 131997600 (0010)

PRE-INST ALLATION REQUIREMENTS

Tools Required for Installation:

1. 1/4 in. nut driver

2. 3/8 in. socket with ratchet.

3. 3/8 in. open end wrench.

4. 7/16 in. socket with ratchet.

5. 9/16 in. open end wrench.

6. Channel-lock adjustable pliers.

7. Carpenter’s level.

in accordance with all local codes and ordinances
or in the absence of local codes, with the National
Electrical Codes, ANSI/NFPA 70 (latest edition).
If in doubt, call a licensed electrician. DO NOT
cut off or alter the grounding prong on the power
supply cord. In situations where a two-slot
receptacle is present, it is the owner’s
responsibility to have a licensed electrician
replace it with a properly grounded three prong
grounding type receptacle.

ELECTRICAL REQUIREMENTS

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay
fuse or circuit breaker.

POWER SUPPL Y - 2 wire, with ground, 120 volt, single
phase, 60 Hz, Alternating Current.

OUTLET RECEPT ACLE - Properly grounded 3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within
42 inches (107 cm) of your washer’s water inlet. The
faucets MUST be 3/4 inch (1.9 cm) garden hose type
so inlet hoses can be connected. Water pressure
MUST be between 10 and 120 pounds per square
inch (maximum unbalance pressure, hot vs. cold, 10
psi.) Your water department can advise you of your
water pressure. The hot water temperature should be
about 140 degrees F (60 degrees C).

DRAIN REQUIREMENTS

1. Drain capable of eliminating 17 gals (64.3 L) per
minute.

2. A standpipe diameter of 1-1/4 in. (3.18 cm)
minimum.

3. The standpipe height above the floor should be:

Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244 cm)

GROUNDING REQUIREMENTS

Improper connection of the equipment
grounding conductor can result in a risk of electrical
shock. Check with a licensed electrician if you are in
doubt as to whether the appliance is properly grounded.

1. The washer MUST be grounded. In the event of

malfunction or breakdown, grounding will reduce
the risk of electrical shock by a path of least
resistance for electrical current.

2. Since your washer is equipped with a power

supply cord having an equipment-grounding
conductor and a grounding plug, the plug MUST
be plugged into an appropriate, copper wired
receptacle that is properly installed and grounded

24 in.

(61 cm)

Min.

NOTE:

Drain hose attached to the washer can reach a
58 in. (147 cm) high standpipe. For higher
standpipe use hose P/N 131461201, available
from an authorized parts distributor. If drain is
less than 24 in. (61 cm), install a siphon break
kit, available at your local hardware store.

2