Frigidaire PLRS237ZAB1, GLRS237ZAQ2, GLRS237ZAB2, FRS23W3AW2, FRS23W3AQ2 Owner’s Manual

...

Side by Side

Welcome ....................... 2

Refrigerator

Safety Instructions ............ 3

Installation -- IncludesConnecting

Ice MakerTo Water Supply ............ 4 - 5

Door Removal

Instructions ................... 6

Features at a Glance ......... 7

Tern perature Controls ....... 8 l_

-11 D

Looking Inside .......... 9

Automatic Ice and Water

-15D

Dispenser ................ 12

Food Storage

& Energy SavingTips ....... 16 D

Normal Operating Sounds.. 17

Care & Cleaning ......... 18 - 19

Warranty ...................... 20

Espafiol ........... 25

Frangais ........... 50

READ AND SAVE THESE INSTRUCTIONS PIN240389302(0107)

Before You Call

Solutions to

Common Problems.............. 21 - 24

Welcome &Congratulations

Congratulations on your purchase of a new refrigerator! We

here at Electrolux Home Products are very proud of our product and we are completely committed to providing you with the best service possible. Your satisfaction is our #1 priority.

Please read this Use & Care Manual very carefully. Itcontains valuable information on how to properly maintain your new

refrigerator. We know you'll enjoy your new refrigerator and Thank You

for choosing our product. We hope you consider us forfuture purchases.

PLEASE READ AND SAVE THESE INSTRUCTIONS This Use & Care Manual provides specific operating

instructions for your model. Use your refrigerator only as

instructed in this manual. These instructions are not meant to cover every possible condition and situation that may

occur. Common sense and caution must be practiced when

installing, operating and maintaining any appliance.

Please record your model and serial numbers below for future reference. This information isfound on the serial

plate located inside the refrigerator compartment.

NOTE: Use only Soap and water to Clean serial plate.

Model Number: Sedal Number:

Purchase Date:

Questions?

1-800-944-9044

(United States)

1-866-213-9397

(Canada)

Extend Your Warranty Protection

With An

Extended Service Contract

CALL 1-800-944-9044

To Enjoy These Benefits:

Total freedom from repair bills so

unexpected repairs won't upset your budget.

Fast, convenient toll-free service is just a phone call away.

Top-quality repairs by factory-trained experts.

Quick access to genuine replacement parts so you can rest assured your

refrigerator is repaired with the proper components.

Please complete and mail in the Product

Registration Card included with your

refrigerator.

Please attach sales receipt

here for future reference.

_ Please Read All Instructions Before Using This Refrigerator.

FOR YOUR SAFETY

• Do not store or use gasoline, or other flammable liquids in the vicinity of this or any other appliance. Read

product labels for warnings regarding flammability and other hazards.

• Do not operate the refrigerator in the presence of

explosive fumes.

• Avoid contact with any moving parts of automatic ice maker.

• Remove all staples from the carton. Staples can cause

severe cuts, and also destroy finishes if they come in contact with other appliances or furniture.

CHILD SAFETY

Destroy or recycle the carton, plastic bags, and any exterior

wrapping material immediately after the refrigerator is

unpacked. Children should NEVER use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly

cause suffocation.

PROPER DISPOSAL OF YOUR REFRIGERATOR

OR FREEZER Risk of child entrapment

Child entrapment and suffocation are not problems of the past.

Junked orabandoned refrigerators or freezers are still dangerous -

even if they will sit for "just a few days." Ifyou are getting rid of your

old refrigerator or freezer, please follow the instructions below to

help prevent accidents.

Before you throw away your old refrigerator/freezer:

• Remove doors.

• Leave shelves in place so children may not easily climb inside.

• Have refrigerant removed by a qualified service technician.

ELECTRICAL INFORMATION

• The refrigerator must be plugged into its own NOTE: Turning the freezer temperature control to OFF dedicated 115 Volt, 60 Hz.,AC only electric outlet, turns off the compressor, but does not disconnect

The power cord of the appliance is equipped with a components. three-prong grounding plug for your protection against

electrical shock hazards. It must be plugged directly into a properly grounded three-prong receptacle. The receptacle must be installed in accordance with local

codes and ordinances. Consult a qualified electrician.

Do not use an extension cord or adapter plug,

• Immediately repair or replace any power cord that becomes frayed or damaged.

• Never unplug the refrigerator by pulling on the power

cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.

• Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock.

• Performance may be affected if the voltage varies by 10% or more. Operating the refrigerator with insufficient

power can damage the compressor. Such damage is not covered under your warranty.

• Do not plug the unit into an outlet controlled by a wall switch or pull cord to prevent the refrigerator from being

turned off accidentally.

• Avoid connecting refrigerator to a Ground Fault Interruptor (GFI) circuit.

electrical power to the light bulb or other electrical

Groundingtype wa receptacle

under

Powercordwith 3-pronggroundedplug

This Owner's Guide provides specific operating

instructions for your model. Use the refrigerator only as instructed in this Use & Care Manual. Before starting the

refrigerator, follow these important first steps. LOCATION

• Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug.

• If possible, place the refrigerator out of direct sunlight

and away from the range, dishwasher or other heat sources.

• The refrigerator must be installed on a floor that is level

and strong enough to support a fully loaded refrigerator.

• Consider water supply availability for models equipped

with an automatic ice maker.

INSTALLATION

• Do Not install the refrigerator where the temperature

will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the refrigerator.

DO Not block the toe grille On the

lower front of your refrigerator, Sufficient air

circulation is essential for the proper operation of your refrigerator.

Installation Clearances

• Allow the following clearances for ease of installation,

proper air circulation, and plumbing and electrical connections:

Sides & Top 3/8"

Back 1"

DOOR OPENING

NOTE: If you refrigerator is placed with the door hinge

side against a wall, you may have to allow additional space so the door can be opened wider.

Your refrigerator should be positioned to allow easy access to a counter when removing food. For best use of drawers

and freezer baskets, the refrigerator should be in a position where both the refrigerator and freezer doors can

be fully opened.

TOE GRILLE INSTALLATION / REMOVAL

To Install Toe Grille:

1. Open freezer and

Cabinet

fresh food compartment doors.

2. Line uptoe grille at base of refrigerator, making sure the four

bottom tabs are resting through holes

at base of cabinet.

3. Starting from left side of toe grille, press in on first top tab using your thumb and push toe grille forward untilitsnaps in place. Continue this process until all tabs aresnapped in place and toe grille is secured to refrigerator.

LEVELING

All four corners of your refrigerator must rest firmly on a solid floor. Your refrigerator is equipped with adjustable front rollers to help level your unit.

To Level Your Refrigerator:

1. Remove toe grille. (See "ToRemove Toe Grille" above.)

2. Use flat-blade screwdriver or 3/8" socket wrench to adjust front rollers.

NOTE: The refrigerator doors are designed to shut by themselves within a 20 degree opening.

Raise

To Remove Toe Grille:

Open freezer and fresh food compartment doors.

Working from left side of toe grille, slip your fingers between top of toe grille and cabinet. Gently pull

forward until first set of tabs are free. Slide your hand down past the free tabs and pull forward again until the

second set of tabs are free. Continue this process until all tabs are free and the toe grille can be removed. (See

graphic at top of page in right column.)

3. Check both doors to be sure seals touch cabinet on all four sides.

Installation - Connecting Ice Maker To Water Supply

To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator

from electrical power before connecting a water supply line to the refrigerator.

To Avoid Property Damage:

Copper tubing is recommended for the water su pply line. Water supply tubing made of ¼" plastic is not recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible

for any damage if plastic tubing is used for supply line.

DO NOT install water supply tubing in areas where temperatures fall below freezing Chemicals from a malfunctioning softener can damage the ice maker. If the ice _naker is connected to soft

water, ensure that the softener is maintained and working properly.

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need

• Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips TM screwdriver

• Access to a household cold water line with water pressure between 20 and 100 psi.

• A water supply line made of 1Ainch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

• A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.

• A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6

meters) of _ inch OD copper tubing, a saddle type shutoff valve (n0npiercing), (2) _ inch brass compression nuts, (2) ferrules/sleeves, and instructions for installing a water supply line.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shut

Plastic Water Tubing

to Ice Maker

Brass

Compression

off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line,

(Sleeve)

as shown.

5. Push water supply line into water valve inlet as far as it will go (IA inch). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut

wateFline

WaterValve

onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of

refrigerator as shown.

7. Coil excess water supply line (about 2V2turns) behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that

leak.

9. Reconnect refrigerator to electrical power source.

(Include enough tubing in Io0p to allow

from household water Supply

10. To turn ice maker on, lower wire signal arm (see ice maker front cover for movingre_igerstoroutforcleaning.) ON/OFF position of arm).

Nut

IMPORTANT: It takes approximately 24 hours f0r the ice maker to begin producing ice. Air in new plumbing lines may cause ice maker to Cycletwo or three times before making a fu!!traYof ice. New plumbing may cause ice to be discolored

or have poor flavor. Discard ice made during the first 24 hours.

Door Removal Instructions

ToolsNecessary:

Top

Phlllc_- head

Wmr_h Sel

3/8" Fb_d

T--Cover Screw

Top Hinge Covet

_'_- Door

Hinge

Assembly

DOOR REMOVAL INSTRUCTIONS:

If it is necessary to move the refrigerator through narrow doorways, follow these steps to remove the doors.

IMPORTANT: Before you begin, turn freezer temperature control to OFF and remove electrical power cord from wall outlet. Remove any

food from door shelves.

1. _isoonnect electricalsupply.

2. Open both doors, then remove toe grille.

3. Close doors.

ToRemove Refrigerator Door:

1. Remove top hinge cover screw on refrigerator door and remove cover.

2. Trace around hinge with soft lead pencil. This will make iteasier to realign doors when they are replaced.

3. Remove top hinge and lift refrigerator door off bottom hinge pin. Set door aside.

4. Remove bottom hinge, if necessary.

5. Reverse this procedure to reinstall refrigerator door

ToRemove Freezer Door:

1. _isconnect water line coming from lower hinge of freezer door at connect=on located under front of freezer: grip water tube firmly in one hand then with 3/8"wrench or fingers, push inon gray collar to release water connector.

2. Remove top hinge cover screw on freezer door and remove cover.

3. _isoonnect wiring harness connector plug at top hinge: place your thumbs on fiat sides of each connector and bend both parts back and forth, then with firm grasp, pull both pieces apart.

4. Trace around hinge with soft lead pencil. This will make iteasier to realign doors when they are replaced.

5. Remove top hinge,allowingwiring hamess to pullthrough hinge and liftfreezer door off ofbottom hinge pin. Laydoordown flat to avoid kinkingwater line.

6. Remove bottom hinge, if necessary.

7. Reverse this procedure to reinstall freezer door.

When both doors have been reinstalled, replace toe grille and plug inelectrical power cord. Turn both temperature controls to center position. Adjust settings

as necessary.

Water

Tubing

Hinge \

P.ssambly \Screws

Features At A Glance

Wire Shelf

Small Items

Door Bin --

Wire Shelf

Door Bin --

Small Basket

Large Basket

Door Bin --

Freezer end Refrigerator

Ice

i!i!i!i!i!i!i!i!

iiiili_ ii

uuuuuuu_l

Hf!,n,lflflflH

IUL]UUHUUI

Controls

SpillSafe'"

Shelf

Water Filter

Door

,rBin

Meat Keeper

and Cover

Fixed Shelf

Special Item

Bottle

Retainer

Large Basket

Door Bin --

IIHlflflflFl lfl

HHHH

pUUUUUUUl

........

Features may vary according to model

Toe Grllle

and Cover

Door Bin

COOL DOWN PERIOD To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 to 12 hours before loading

itwith food. REFRIGERATOR & FREEZER CONTROLS

NOTE: When first turning refrigerat0r 0n, move refrigerator Cold contro! toy which isthe recommended initia!setting.

After 24 hours, adjust the controls as needed.

TEMPERATURE ADJUSTMENT

• After 24 hours, adjust the controls as needed. Adjust

FactorySett_lI F_ttoty Se#iijr

temperatures gradually: move the knob in small

increments, allowing the temperature to stabilize.

• For colder temperatures, turn the knob towards Colder.

• Forwarmer temperatures, turn the knob towards Warmer. To maintain temperatures, a fan circulates air in the

Freezer _._ FreshFood

refrigerator and freezer compartments. For good circulation,

do not block cold air vents with food items.

Refrigerator & Freezer Controls

IMPORTANT: Turning the freezer temperature control to "Off" turns Offthe compressor, but does not disconnect the power to the light bulb and other electrical components.

TEMPERATURE ADJUSTMENT GUIDE

If Refrigerator Compartment Is Too Warm Turn Refrigerator Control Slightly Towards Colder.

If Refrigerator Compartment Is Too Cold Turn Refrigerator Control Slightly Towards Warmer.

If Freezer Compartment Is Too Warm Turn Freezer Control Slightly Towards Colder.

If Freezer Compartment Is Too Cold Turn Freezer Control Slightly Towards Warmer.

To Turn Refrigerator Off Turn Freezer Control To Off.

PIZZA SHELF (SOME MODELS)

This shelf is attached to the freezer wall beside the ice dis )enser container. This convenient area allows for storage of pizza and other tall itemsplaced

vertically between the ice dispenser container and the freezer wall. ICE CREAM SHELF (SOME MODELS)

This shelf attaches to the top of the ice dispenser container. It allows storage of both round and rectangular cartons of your favorite ice cream.

TIP-UP SHELF (SOME MODELS) ATip-Up shelf inthe freezer section allows tall items to be easily stored.

To avoid personal injury or property damage, handle

tempered glass shelves carefully. Shelves may break suddenly if

nicked, scratched, or exposed to sudden temperature change.

CANTILEVER SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting the shelves, remove all food. Cantilever shelves are supported at the back of the refrigerator.

To adjust cantilever shelves:

O Lift front edge up. O Pull shelf out.

Replace the shelf by inserting the hooks at rear of the shelf into the wall bracket. Lower the shelf intothe desired slots and lock into position.

SpillSafe TM glass shelves (some models) catch and hold accidental spills. In

some models, the SpillSafe TM shelves slide out for easy access to food and ................

for fast cleaning. The shelves slide out independentlyof their mounting brackets. Just pull the front of the shelf forward. Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets.

Pizza Shelf

Ice Cream Shelf

Cantilever Glass Shelf

Cantilever Sliding Glass Shelf

DOOR STORAGE

Door bins and shelves are provided for convenient storage of jars, bottles, and cans. Frequently used items can be quickly selected.

Some models have door bins that can accommodate gallon- sized plastic drink containers and economy-sized jars and containers. Some bins are adjustable for maximum storage capacity.

The dairy compartment, which is warmer than the genera_ food storage section, is intended for short term storage of

cheese, spreads, or butter.

FixedDoor Bin

ADJUSTABLE DOOR BINS

Some models have adjustable door bins that can be moved to suit individual needs.

Tomove door bins

1. Lift bin straight up.

2. Remove bin.

3. Place bin in desired position.

4. Lower bin onto supports until locked in place.

TALL BOTTLE RETAINER (SOME MODELS)

The Tall Bottle Retainer keeps tall containers in the bin from falling forward when opening or closing the refrigerator doo£ To install, hold the retainer at the top, and slide it over the outside wall of the bin, as shown in the diagram. The Tall Bottle Retainer works best with a Bin Snugger.

Tall Bottle Retainer (lefB ana Bin Snugger (right)

SPECIAL ITEM RACK (SOME MODELS)

The innovative design of the Special Item Rack allows you to store a six-pack of 12 ounce drink cans. a bottle of wine a two-liter soft drink bottle, or a carton of eggs. The Special Item Rack mounts on the left side of your refrigerator. To install, just slide the Special Item Rack onto any shelf as shown inthe drawing.

Adjustable Door Bin

Special ItemRack

CRISPERS (SOME MODELS)

The crispers, located under the bottom refrigerator shelf, are designed for storing fruits, vegetables, and other fresh produce. Wash itemsinclear water and remove excess water before placing them inthe crispers. Items with strong odors or high moisture content should be wrapped before storing.

Crisper Drawer

MEAT KEEPER (SOME MODELS)

Some models are equipped with a Meat Keeper. Meat Keeper temperatures can be adjusted by sliding the Meat Keeper Temperature Control in either direction. Use this pan for short term storage of bulk meat items. If meats are to be kept longer than one or two days, they should be frozen. The Meat Keeper is fixed and cannot be moved up or down. If fruits or vegetables are to be stored in the Meat Keeper, set the Meat Keeper Temperature Control to a warmer setting to prevent freezing.

HUMIDITY CONTROL (SOME MODELS)

The Humidity Control, present on some models with crisper drawers, allows you to adjust the humidity within the crisper. This can extend the life of fresh vegetables that keep best

in high humidity.

NOTE: Leafy Vegetables keePbest when Storedwith the

Humidity Control set on Higher Humidity, or in a drawer

without a Humidity Control. This keeps incoming airto a

minimum and maintains maximum moisture content.

_wer HumJdJ_

Crisper Humidity Control

DELl DRAWER (SOME MODELS)

Some models are equipped with a Dell Drawer for storage of

luncheon meats, spreads, cheeses, and other dell items.

Meat Keeper with Temperature Control

WINE RACK (SOME MODELS) The wine rack stores bottles of wine, or single two-liter plastic

bottles of juice or soda pop. To install, slide the Wine Rack onto the shelf with the curve facing in. To remove, slide the

Wine Rack out. Install on either side of shelf.

Wine Rack

Automatic Ice and Water Dispenser

ICE AND WATER DISPENSER FEATURES

The ice and water dispenser conveniently dispenses chilled water, and ice

cubes or crushed ice. depending on the model. Some models have an Extra Ice feature that increases ice production for special occasions such as parties.

To operate the ice dispenser select the ice option desired using the touchpad.

Press a glass against the dispensing paddle as far up as possible to catch all ice. To stop dispensing ice, pull glass away from dispensing paddle. Do not remove the g_ass until the ice has completely dispensed. (Complete instructions for the dispenser operation are attached to the inside of the freezer door.)

Tooperate the water dispenser, press a glass against the dispensing paddle.

To stop dispensing water, pull glass away from dispensing paddle. A drip

tray located at the base of the dispenser, catches small spills and allows them to evaporate. This drip tray isremovable and dishwasher safe. Do not

pour water or excess cubes into this area because there is no drain.

Dispenser Light (some models)

The dispenser has a light which can be turned on and off by pressing the Light

touchpad. The light also turns on automatically when ice and/or water is dispensed. Replace light bulb with an appliance bulb of the same wattage.

Signa_ Arm

Exlml==Cube Crush Light F_S_s

Ice and Water Dispenser Panel (features may vary according to model)

How the Water Dispenser Works

The water tank, located behind the drawers in the refrigerator compartment, automatically fills as water isdispensed. For proper dispenser operation, the recommended supply water pressure should fall between 20 psi and 100 psi.

After the refrigerator is connected to the water supply, fill the water tank by drawing one glass of water. It may take about

1'/2minutes after activating the dispenser paddle before water begins to fill this first glass. Continue flushing the system for 3 minutes to rid the tank and plumbing connections of any impurities. The water dispenser has a built in shutoff device that will stop the water flow after 3 minutes of continuous use. Simply release the dispenser paddle to reset the shutoff

mechanism.

Chemicals from a malfunctioning softener can damage the ice maker. Ifthe ice maker is connected

to soft water, ensure that the softener is maintained and working properly.

How the Ice Dispenser Works

The ice maker and container are located in the top of the freezer compartment. After the refrigerator is installed properly and has cooled for several hours, the ice maker can begin making ice within 24 hours. Air innew plumbing lines may cause the ice maker to cycle two or three times before making a full tray of ice. To begin ice production, lower the wire signal arm to the "down" or ON position. With no usage itwill take approximately 2 days to fill the ice container. The ice maker turns off automatically when the icecontainer becomes full. To stop the ice maker, lift the wire signal arm until it clicks, and locks in the "up" or OFF position.

Because of new plumbing connections, the first production of ice cubes may be discolored or have an odd flavor. These should be discarded until the cubes made are free of discoloration and taste.

ICEDISPENSERTIPS

• Icecubesstoredtoolongmaydevelopanoddflavor.Emptytheicecontainerandensurethatthewiresignalarmis inits"down"orONposition.Theicemakerwillthenproducemoreice.

• Occasionallyshaketheicecontainertokeepiceseparated.

• Keepthewiresignalarminits"up"orOFFpositionuntiltherefrigeratorisconnectedtothewatersupplyorwheneverthe

watersupplyisturnedoff.

If the dispensing paddle is pushed for more than 4 minutes, the dispenser motor may overload

and stop. The overload protector will reset automatically after 3 or 4 minutes,

• If a large quantity of ice is needed at one time, it is best to remove cubes directly from the ice container.

• The following sounds are normal when the ice maker is operating:

• Motor running

• Ice loosening from tray

• Ice dropping into ice container

• Running water

• Water valve opening or closing Stop the ice maker when cleaning the freezer and during vacations.

• If the ice maker will be turned off for a long period of time, turn the water supply valve to the closed position.

CLEANING THE ICE DISPENSER

30not use theicechuteas ahandlewhen

removingorreplacingtheicestoragebin. Surfacesthere may be sharp,

Do not put fingers up ice chute, Surfaces

there may be sharp. •

Auger-_/

Clean the dispenser and ice container at regular intervals, particularly before you take a vacation or move, or ifthe ice dispenser sticks.

1. Stop ice production by lifting the wire signal arm to the "up" or OFF position.

2. Remove ice container by lifting up and out. Empty and carefully clean the container with mild detergent. Rinse with clear water. Do not use

harsh or abrasive cleaners. Allow icecontainer to dry completely before replacing inthe freezer.

3. Remove ice chips and clean the shelf and chute that supports the ice container.

4. Replace the ice container. Lower the wire signal arm on the ice

maker to the "down" or ON position and the ice maker will resume production.

IMPORTANT: When removing or replacing the ice bin. do not rotate the auger in the ice bin. If the auger is accidentally turned. you must realign the auger by turning it in90 °turns until the ice bin fits into place with the drive mechanism, For further instruction.

see the label on the ice bucket.

Remove and empty the ice storage bin if:

1 An extended power failure _onehour or longer) causes ice cubes n

the ice storage bin to melt and freeze together and jam the dispenser

mechanism

2. The ice dispenser is not used frequently. Ice cubes will freeze together inthe bin and ,am the dispenser mechanism. Remove the ice storage

bin and shake to loosen the cubes.

NEVER use an ice pick or similar sharp instrument to break up the ice.

This could damage the ice storage bin and dispenser mecnanlsm.

PureSource TMIce and Water Filter (some models)

NOTE: If you purchased a refrigerator with a PureSource T_ Ice and Water filter, please read the following use and

care information. This ice and water filter system filters water to your ice maker and water dispenser. It is located inthe

upper right back corner of the fresh food compartment.

System Startup:

Water supply does not need to be turned off, however, do not use ice and water dispenser while installingfilter. The filter cartridge has already been installed in the filter housing at the factory. Refer to the How The Water Dispenser Works section

to properly fill the system with water. Changing the Filter:

Water conditions vary throughout the world, but changing the water filter every

F 6 - 9 months normally will ensure the highest possible water quality. The FilterStatus light will turn red after 400 gallons of water has flowed through the ice and

water dispenser (some models). Also, if the filter has been in a refrigerator that has not been in use for awhile (during moving for example), change the filter

before reinstalling the refrigerator. The dispenser system will also operate without

filtration (with filter cartridge removed).

To change filter:

It is not necessary to turn the water supply off to change the filter.

1. Open freezer door and leave open until filter change is complete.

2. Set ice maker wire signal arm to the OFF (up) position (See illustration on page 12).

Large O-ringJ

FilterCup_

3. Hold filter cup firmly, and unscrew towards left (Some water could leak out as you remove cup. This is normal.). Filter cartridge should come down with cup. If cartridge remains in housing, pull down gently, while twisting filter back and forth.

4. Rinse out cup under running water.

Twistto

5. The large o-ring that seals the filter system sets in the o-ring groove down inside the cup. Should the o-ring fall out during filter cartridge replacement, simply place it back in the groove prior to screwing the cup

Order new filter cartridges through the dealer where you bought the refrigerator,

or contact the Consumer Assistance

Center at 1-800-944-9044. It might be

good to order some filter cartridges when you first install your refrigerator. Be sure

to ask for the RG-100 PureSource TM

replacement cartridge.

back in place. If the o-ring becomes damaged, you will need to order one from the Consumer Assistance Center.

6. Discard old filter cartridge.

7. Remove new filter cartridge from packaging and place in cup. The end with the small o-ring should be up, out of the cup.

8. Screw cup, with filter, back onto housing. Do Not Use Wrench To Reinstall Cup. Filter cartridge will self-align as cup is tightened. Be sure cup is completely tightened with PureSource TM logo facing outward. Do Not

Tighten Past Stop.

9. Set ice maker wire signal arm to the ON (down) position.

The PureSource TM NGRG- 2000 Ice and Water Filter System with the RG-100 cartridge is tested and

certified by NSF International,

the nationally recognized and respected, not for profit, certification organization for

)ublic health safety. The PureSource TM system is tested and certified to ANSI/NSF Standard 42. See performance data sheet

for specifications. This system should not be used on water that is microbiologically

unsafe or with water of unknown quality unless the water has been adequately

disinfected before or after traveling through the filtration system.

• Rated Capacity - 400 gallons

• Rated service flow - .5 GPM

• Maximum Rated Pressure - 100 PSI

• Maximum Operating Temp. - 100 ° F

10. Check for leaks. Open refrigeratordoor. Wipe any water droplets from the filter cup. Fill a glass with water. If there is a leak, unscrew filter cup, and reinsert the filter cartridge. Check placement of large O-ring. Reinstall filter cup, making certain it is tightened completely.

11. To condition filter system and purge air from water line, fill a glass with water. Continue flushing the system for 30 seconds to assure that the purest water possible is stored in water tank.

IMPORTANT: Resetting The Filter Status Light(some models) After replacing the filter cartridge, it will be necessary to press the Filter

Status reset button located on the ice and water dispenser. This will reset

the Filter Status light. Push the reset button until the green light flashes (3-15 seconds). Please refer to the complete dispenser operating

instructions attached to the inside of the freezer door.

On models without a Filter Status reset button, there is a set of

Reminder Stickers includedin the plasticbag thatthe Use 8,Care Manual

came in. Choose a dated sticker that indicates 6 _ 9 months (depending on your water quality and usage) from the date of installation. Place the

sticker on the front of the filter cup toremind you when it is time to

change the filter.

PureSource2TM Ice and Water Front Filter (some models)

NOTE: _fy_u purchased a refrigerat_r with a PureS_urce2TM _ceand water fr_nt fi_ter' p_ease read the f____winguse

and care information. This iceand water filter system filters water to your ice maker and water dispenser. It is located in

the upper right front corner of the fresh food compartment.

System Startup:

Works section to properly fill the system with water.

Changing the Filter:

Water conditions vary throughout the world, but changing the water filter every 6 - 9 months normally will ensure the highest possible water quality. The Filter Status light will turn red after approximately 400 gallons of water has flowed through the ice and water dispenser. Also, ifthe filter has been ina refrigerator that has not been inuse for awhile (during moving for example), change the filter

before reinstalling the refrigerator. The dispenser system will also operate without filtration (with filter cartridge removed and bypass installed).

To change filter:

I ......

andClick ToInstall To Re!ease

It is not necessary to turn the water supply off to change the filter.

1. Set ice maker wire signal arm to the OFF (up) position (See illustrationon

page 12).

2. Push the Filter Release Button, located to the right of the filter cartridge, to release the filter from the housing. To minimize the possibility of the filter falling out of the housing during removal, itwould be best to hold the

Order new filter cartridges through the dealer where you bought the refrigerator,

or contact the Consumer Assistance Center at 1-800-944-9044. It might be

good to order some filter cartridges when

you first install your refrigerator. Be sure to ask for the PureSou rce2TM replacement

cartridge.

filter as it moves out toward you.

NOTE: A small amount of water may be released during this operation.

You should have a paper towel or dish cloth handy to wipe up any water

that may drip out of the filter or housing. Two small holes near the back of

the housing have been added for any excess water to escape. It would be

best to clear away any food near this area on the top shelf in advance of removing the filter.

3. Pull the old filter cartridge straight out of the housing.

4. Discard the old filter.

5. Remove the new filter cartridge from the packaging and insert intothe

The PureSource2 TM Ice and Water Filter System NGFC

2000 with the PureSource2 TM cartridge FC 100 istested and

certified by NSF International,

the nationally recognized and respected, not for profit, certification organization for

)ublic health safety. The PureSource2 TM

Filter system is tested and certified to ANSI/ NSF Standards 42 and 53. See

)erformance data sheet for specifications.

This system should not be used on water that is microbiologically unsafe or with water

of unknown quality unless the water has been adequately disinfected before or after

traveling through the filtration system.

• Rated Capacity - 400 gallons

• Rated service flow - .5 GPM

• Maximum Rated Pressure - 100 PSI

• Maximum Operating Temp. - 100 ° F

filter housing the same way the old one came out.

6. When the cartridge isalmost in,you will feel it stop against the clip assembly in the back of the housing. The clip assembly holds the filter cartridge firmly inplace. At this point, you will need to push firmly until the cartridge snaps fully inplace. When completely inplace, the front of the filter cartridge will be flush with the front of the housing.

7. Set the ice maker wire signal arm to the ON (down) position.

8. Fill a glass with water. As you are doing this, check for leaks at the filter housing. There will be noticable spurts and sputters as the system pushes the air out through the system and out the dispenser nozzle. This isnormal.

9. After you have run one glass of water, continue to flush the system for approximately 3minutes to assure that the purest water possible is stored in the water storage tank.

IMPORTANT: Resetting The Filter Status Light (some models)

After replacing the filter cartridge, it will be necessary to press the Filter

Reset button located on the ice and water dispenser. This will reset the Filter Status light. Push the reset button until the green light flashes (3-15 seconds). Please refer to the complete dispenser operating instructions

attached to the inside of the freezer door.

Food Storage& Energy Saving Ideas

FOOD STORAGEIDEAS

Fresh Food Storage

• The fresh food compartment should be kept between 34° F and 40° F with an optimum temperature of 37° E

• Avoid overcrowding the refrigerator shelves. This reduces the circulation of air around the food and results in uneven cooling.

Fruits and Vegetables

• Storage inthe crisper drawers traps moisture to help preserve the fruit and vegetable quality for longer time periods.

Meat

• Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or surfaces does not occur.

Frozen Food Storage

• The freezer compartment should be kept at 0° F or lower.

• A freezer operates most efficiently when it is at least 2/3 full.

Packaging Foods for Freezing

• To minimize dehydration and quality deterioration, use aluminum foil, freezer wrap, freezer bags or airtight containers.

Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out,

change color, and develop an off-flavor (freezer burn).

• Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.

• Do not refreeze meat that has completely thawed.

Loading the Freezer

• Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing, and can raise the temperature of frozen foods.

• Leave a space between the packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.

• Avoid storing hard-to-freeze foods such as ice cream and orange juice on the freezer door shelves. These foods are best stored in the freezer interior where the temperature varies less.

ENERGY SAVING IDEAS

• Locate the refrigerator inthe coolest part of the room, out ofdirect sunlight, and away from heating ducts or registers. Do not place the refrigerator

next to heat-producing appliances such as a range, oven, or dishwasher. If this is not possible, a section of cabinetry or an added layer of insulation between the two appliances will help the refrigerator operate more efficiently.

• Level the refrigerator so that the doors close tightly.

• Refer to this Use & Care Manual for the suggested temperature control

settings.

• Periodic cleaning of the condenser will help the refrigerator run more

efficiently. See the Care and Cleaning Chart on page 17.

• Do not overcrowd the refrigerator or block cold air vents. Doing so causes the refrigerator to run longer and use more energy.

• Cover foods and wipe containers dry before placing them in the

refrigerator. This cuts down on moisture build-up inside the unit.

• Organize the refrigerator to reduce door openings. Remove as many

items as needed at one time and close the door as soon as possible.

UNDERSTANDING THE SOUNDS YOU MAY HEAR

Your new high-efficiency refrigerator may make unfamiliar sounds. Don't be alarmed, these are all normal sounds. Hard

surfaces, such as vinyl or wood floors, walls, and kitchen cabinets may make sounds more noticeable. Listed below

are descriptions of some of the most common sounds you may hear, and what is causing them.

NOTE: Rigid foam insulation is very energy efficient,

but isnot a sound insulator.

A. Evaporator

The flow of refrigerant through the evaporator may create aboiling or gurgling sound.

B. Evaporator Fan

You may hear air being forced through the refrigerator by the evaporator fan.

C. Defrost Heater

During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After defrosting, a popping sound may occur.

IMPORTANT: During the automatic defrost cycle, you may notice a red glow in the vents on the back walt of your freezer c0mpartmenL This is normal during the defrost cycle.

D. Automatic Ice Maker

If your refrigerator isequipped with an automatic ice

maker, you will hear ice cubes falling into the ice bin.

E. Cold Control & Defrost Timer

These parts can produce a snapping or clicking sound when turning the refrigerator on and off. The timer also produces sounds similar to an electric clock.

F. Condenser Fan

You may hear air being forced through the condenser by the condenser fan.

G. Compressor

Modern, high-efficiency compressors operate much faster than older models. The compressor may have a high-pitched hum or pulsating sound.

H. Water Valve

If your refrigerator isequipped with an automatic ice

maker, you will hear a buzzing sound as the water valve opens to fill the ice maker during each cycle.

L Drain Pan

You may hear water running intothe drain pan during the defrost cycle.

J. Condenser

Care&Cleaning

Keep your refrigerator and freezer clean to prevent odor build-up. Wipe upany spills immediately and clean both sections at least twice a year. Never use metallic scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any

surface. Do not wash any removable parts in a dishwasher. Always unplug the electrical power cord from the wall outlet before cleaning.

rR4, m

• When moving the refrigerator, pull straight out. Do not shift the refrigerator from side to side as this may damage the floor. Be careful not to move the refrigerator beyond the plumbing connections.

Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp hands.

To avoid damage and help the refrigerator run as efficiently as possible, clean the condenser periodically.

NOTES:

Turning the freezer temperature control toOFF turns off the compressor, but does not disconnect electrical power to the light bulb or other electrical components.

Do not use razor blaoes or other sharp instruments which can scratch the appliance surface when removing

adhesive labels. Any glue left from tape or labels can be removed with a mixture of warm water and mild detergent, or.touch the glue residue with the sticky side of tape you have already removed. Do not remove the

serial plate.

Part

Interior/Door • Liner •

Door Gaskets • Drawers/Bins •

Glass • Shelves •

Toe Grille •

Exterior and • Handles

Exterior and • Handles •

(Stainless • Steel Models

Only)

Condenser • Coils

Care & Cleaning Chart

Cleaning Agents Tips and Precautions

Soap and water Use 2 tablespoons of baking soda in 1 quart of warm water. Be Baking soda and sure to wring excess water out of sponge or cloth before

water cleaning around controls, light bulb or any electrical part. Soap and water Wipe gaskets with a clean soft cloth.

Soap and water Do not wash any removable items (bins, drawers, etc.) in

dishwasher.

Soap and water Allow glass to warm to room temperature before immersing in Glass cleaner warm water.

Mild liquid sprays Soap and water Vacuum dust from front of toe grille. Remove toe grille (See

Mild liquid sprays illustration on page 5). Vacuum backside and wipe with sudsy Vacuum attachment cloth or sponge. Rinse and dry.

Soap and water Do not use commercial household cleaners, ammonia, or alcohol

to clean handles.

Soap and water Ammonia Stainless Steel

Cleaners

Vacuum attachment Use the dusting tool attachment on your vacuum to remove dust

Clean stainless steel front and handles with non-abrasive soapy

water and a dishcloth. Rinse with clean water and a soft cloth.

Wipe stubborn spots with an ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless steel cleaner. These cleaners

can be purchased at most home improvement or major department stores. Always follow manufacturer's instruction.

NOTE: Always, clean, wipe and dry with the grain to prevent cross-grain scratching. Wash the rest of the cabinet with warm

water and mild liquid detergent. Rinse well, and wipe dry with a

clean soft cloth.

build-up on the condenser coils (see item "J" in illustration on page 17 for location).

r _ Wear gloves when replacing light

bulbs to avoid getting cut.

REPLACING LIGHT BULBS

1. Unplug refrigerator.

2. Wear gloves as protection against possible broken glass.

& Remove light cover, if necessary.

4. Unscrew and replace old bulb with an appliance bulb of the same wattage.

5. Replace light cover, if necessary.

6. Remember to plug the refrigerator back in.

Refrigerator Light Replacement

LightSocket LocatedBehin

LeftRear

of Crispers

Crisper Light Replacement (Some Models)

Crisper Light

UghtBulb _

Ugh_Bu!b¢

Lc_,atedBehindRight RearofIceContainer

Freezer Light Replacement

Vacation and Moving Tips

Short

Vacations

Long • Turn off automatic ice maker and turn water supply valve to closed position. Vacations • Clean interiorthoroughly.

• Leave refrigerator operating during vacations of 3 weeks or less.

• Use all perishable items from refrigerator compartment.

• Turn automatic ice maker off, even if you will only be gone for a few days.

• Remove all food and ice ifyou will be gone one month or more.

• Turn controls to OFF and disconnect power.

• Leave both doors open to prevent odors and mold build-up. Block doors open if necessary.

• Remove all food and ice.

Moving

IMPORTANT: If the refrigerator is going to be stored or moved infreezing temperatures, the water in

the ice and water system must be drained completely. Failure to do so could result in water leaks when

the refrigerator is put back intoservice. Contact a service representative to perform this operation.

• If using handcart, load from side.

• Adjust rollers all the way up to protect them during sliding or moving.

• Pad cabinet to avoid scratching surface.

REFRIGERATOR WARRANTY

Your refrigerator is protected by this warranty

WARRANTY THROUGHOURAUTHORIZEDSERVICERS, THECONSUMERWILLBE RESPONSIBLEFOR:

PERIOD WEWILL:

FULLONE-YEAR Oneyearfrom original PayaJlcostsfor repairingor replacinganypartsof this Costs of service calls that are listed under NORMAL WARRANTY purchasedate appliancewhichproveto be defectivein materiaJsor RESPONSIBILITIESOF THE CONSUMER.*

LIMITED2N%5T" Secondthroughfifth Repairor replaceanypartsinthecabinetlineror Costsfor pickup anddeliveryofthe appliancerequiredbecause

YEARWARRANTY yearsfromoriginal SealedRefrigerationSystem(compressor,condenser, of service.Costs forlabor,partsand transportationotherthan (Cabinet Litter and purchasedate evaporator,drierandtubing)whichprovetobe withrespectto thecabinetlineror SealedRefrigerationSystem. SealedSystem) defectivein materialsorworkmanship.

LIMITED Timeperiodslisted All of theprovisionsofthefullwarrantiesaboveand Costsof thetechnician'stravelto thehomeandanycostsfor WARRANTY above, theexclusionslistedbelowapply, pick up anddeliveryofthe appliancerequiredbecauseof

(Applicableto the service. StateofAlaska)

In the U.S.A., your appliance is warranted by Electrolux Home Products North America, a division of White Consolidated Industries Inc. We

authorize no person to change or add to any of our obligations under this warranty. Our obligations for service and pads under this warranty must be pedormed by us or an authorized Electrolux Home Products North America servicer. In Canada, your appliance is warranted by WCI Canada Inc.

*NORMAL

RESPONSIBILITIES

OF THE CONSUMER

EXCLUSIONS

IF YOU NEED SERVICE

This warranty applies only to products in ordinary household use, and the consumer is responsible for the

items listed below:

1. Proper use of the appliance in accordance with instructions provided with the product.

2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance with all local plumbing, electrical and/or gas codes.

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house wiring.

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,etc., which are not a part of the appliance when it was shipped from the factory.

5. Damages to finish after installation.

6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).

This warranty does not cover the following:

1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.

NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this iimitation or exclusion may not apply to you.

2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary household use. The consumer shall pay for such service calls.

3. Damages caused by services performed by servicers other than Electrolux Home Products North America or its authorized servicers; use of parts other than genuine Electrolux Home Products parts; obtained from persons

other than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all

receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this warranty must be obtained by contacting Eiectrolux Home Products:

workmanship.Excludesoriginal and replacementice & Water filter cartridges(if equipped). OriginaJand replacement cartridges are warranted for 30 days

(partsonly).

This warranty only applies in the 50 states of the U.S.A., Puedo Rico, and Canada. Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by Electrolux Home Products North America, a division of White ConsoIidated

Industries Inc. In Canada, your appliance is warranted by WCI Canada Inc.

01-U-RE-02 (Rev. 12/2000

USA 800°944.9044

Ele_lux Home Products Norfh America RO. Box 212378

Augusta, GA 30917

Elect_lux Home Predu_s Norfh America

6150 McLaughlin Road

Mississauga, Ontario

Canada

866o213o9397

L5R 402

PROBLEM CAUSE CORRECTION

RUNNING OF REFRIGERATOR

Compressor does not run.

Refrigerator runs too much or too long.

Compressor goes off and • Thermostat keeps the • This is normal Refrigerator goes on and off to keep

on frequently, refrigerator at a constant temperature constant.

TEMPERATURES ARE TOO COLD

• Freezer control is OFF.

• Refrigerator is in defrost cycle

• Plug at wall outlet is disconnected

• House fuse blown or tripped circuit breaker.

• Power outage

• Room or outside weather is hot

• Refrigerator has recently been disconnected for a period of

time.

• Automatic ice maker is operating.

• Doors are opened too frequently or too long.

• Refrigerator/freezer door may be slightly open.

• Freezer control is set too cold (control found in refrigerator

section).

• Refrigerator/freezer gasket is dirty, worn, cracked, or poorly

fitted,

• Condenser is dirty.

temperature.

• Set freezer control. See Temperature Controls section.

• This is normal for a fully automatic defrost refrigerator. The defrost cycle occurs periodically, lasting about 30

minutes.

• Ensure plug is tightly pushed into outlet.

• Check/replace fuse with a 15 amp time-delay fuse.

Reset circuit breaker.

• Check house lights. Call local Electric Company,

• It's normal for the refrigerator to work longer under these conditions.

• It takes 8-12 hours for the refrigerator to cool down completely.

• Ice maker operation causes refrigerator to run slightly more

• Warm air entering the refrigerator causes it to run more Open doors less often.

• Ensure refrigerator is level, Keep food and containers from blocking door See PROBLEM section

OPENING/CLOSING OF DOORS/DRAWERS,

• Set refrigerator control to warmer setting until

refrigerator temperature is satisfactory. Allow 24 hours

for temperature to stabilize.

• Clean or change gasket. Leaks in door seal will cause

refrigerator to run longer in order to maintain desired

temperatures. Clean condenser. See Care & Cleaning Chart in Care and Cleaning section.

Freezer temperature too • Freezer control is set too cold. • Set freezer control to a warmer setting. Allow 24 hours

cold, Refrigerator for temperature to stabilize. temperature is satisfactory.

Refrigerator temperature • Refrigerator control is set too • Set refrigerator control to a warmer setting. Allow 24 too cold. Freezer cold. hours for temperature to stabilize. temperature is satisfactory.

Food stored in drawers • Refrigerator control is set too • See solution above. freezes, cold.

Food stored in Meat • Meat Keeper Temperature • Adjust Meat Keeper Temperature Control to a lower

Keeper freezes (some Control set too cold. setting. (Meat should be stored at a temperature just

models), below the freezing point for maximum fresh storage

time. It is normal for ice crystals to form due to the moisture content of meat.)

PROBLEM CAUSE CORRECTION

TEMPERATURES ARE TOO WARM

Freezer/Refrigerator • Doors are opened too • Warm air enters the refrigerator whenever the door is temperature is too warm, frequently or too long. opened. Open the door less often.

• Door is slightly open. • See PROBLEM section OPENING/CLOSING OF DOORS/DRAWERS.

• Condenser is dirty. • Clean condenser. See Care & Cleaning Chart in Care and Cleaning section.

Freezer temperature is too • Freezer control is set too • Set freezer control to a colder setting. Allow 24 hours warm. Refrigerator warm. for temperature to stabilize. temperature is satisfactory.

Refrigerator temperature is • Refrigerator control is set too • Set refrigerator control to a colder setting. Allow 24 too warm. Freezer warm. hours for temperature to stabilize. temperature is satisfactory.

Temperature in the Meat • Meat Keeper Temperature • Adjust Meat Keeper Temperature Control to a colder Keeper is too warm (some Control is set too warm. setting.

models).

WA TERIMOIS TUREIFROS T INSIDE REFRIGERATOR

• Weather is hot and humid.Moisture collects on inside

of refrigerator walls,

• Door is slightly open.

• Door is opened too often or too

long.

• Open containers.

Water collects on bottom • Vegetables contain and give • It is not unusual to have moisture on the bottom side of side of drawer cover, off moisture, the cover.

Water collects in bottom of • Washed vegetables and fruit • Dry items before putting them in the drawer. Water drawer, drain while in the drawer, collecting in bottom of drawer is normal.

WA TERIMOISTUREIFROST OUTSIDE REFRIGERATOR

Moisture collects on • Weather is humid. • This is normal in humid weather. When humidity is outside of refrigerator or lower, the moisture should disappear.

between doors, • Door is slightly open, causing • See PROBLEM section OPENING/CLOSING OF

cold air from inside refrigerator DOORS/DRAWERS. to meet warm air from outside.

AUTOMATIC ICE MAKER

Ice maker is not making any ice,

• Ice maker wire signal arm is in

the "up" or OFF position.

• Household water line valve is

not open.

• Freezer is not cold enough.

• Saddle valve on cold water

pipe is clogged or restricted by foreign material.

Check to see if the water dispenser is dispensing water.

• The rate of frost buildup and internal sweating increases.

• See PROBLEM section OPENING/CLOSING OF DOORS/DRAWERS.

• Open door less often.

• Keep containers covered.

• Move humidity control (some models) to lower setting.

• Move wire signal arm to the "down" or ON position.

• Turn on household water line valve.

• See PROBLEM section TEMPERATURES ARE TOO

WARM.

• Turn off household water line valve. Remove valve. Ensure that valve is not a self-piercing saddle valve. Clean valve. Replace valve if necessary.

• If not, the ice & water filter cartridge is clogged or restricted by foreign material, and must be replaced.

PROBLEM CAUSE

A UTOMA TIC ICE MAKER (CONTINUED)

CORRECTION

Ice maker is not making • Ice maker is producing less ice

enough ice. than you expect.

• Freezer is not cold enough.

• Household water line valve is not completely open.

• Check to see if water

dispenser is dispensing slower than normal.

Ice maker will not stop • • Move item and release wire signal arm. Remove any making ice. ice cubes that are frozen together over the wire signal

Ice maker is not separating • • Remove and shake ice container to separate cubes.

the ice cubes,

Ice has bad odor and taste. • • Cover foods tightly. Discard stale ice. Ice maker will

ICE DISPENSER

Dispenser will not dispense ice.

Ice dispenser isjammed.

Ice maker wire signal arm is being held down by some item

in the freezer. Ice cubes are not being used

frequently enough.

Ice cubes are hollow or smaller

• • The ice & water filter cartridge may be clogged.

than normal.

Ice has picked up odor or

flavor from strong food stored

in refrigerator or freezer.

Water running to ice maker

• • Add filter to water supply line. Consult a water has poor taste or odor.

• • Discard stale ice.

Ice not used frequently enough.

• Ice storage container is empty.

• Freezer temperature is set too

waiTn.

• Household water line valve is net open.

Freezer door is not closed. Ice dispensing arm has been

held in for more than 4-5 minutes.

• Ice has melted and frozen

around auger due to infrequent

use, temperature fluctuations,

and/or power outages.

• Ice cubes are jammed between ice maker and back

of ice container.

• Ice cubes are frozen together.

Ice cubes are hollow or smaller

than normal.

• Ice maker should produce approximately 4 - 5 pounds of ice every 24 hours. Extra Ice should produce up to 8

pounds of ice every 24 hours.

• See PROBLEM section TEMPERATURES ARE TOO WARM.

• Tum on household water line valve.

If it is, replace the ice & water filter cartridge.

arm.

Replace filter cartridge.

produce fresh supply.

purifying company.

• When the first supply of ice is dropped into the container, the dispenser should operate.

• Tum freezer control to a higher setting so that ice cubes will be made. When first supply of ice is made,

dispenser should operate.

• Open household water line valve. Allow sufficient time for the ice to be made. When ice is made, the

dispenser should operate.

• Ensure freezer door is closed.

• Motor is overloaded. Motor overload protector will

reset in approximately 3 minutes. Ice can then be

dispensed.

Remove ice container, thaw, and empty the contents.

Clean container, wipe dry, and replace in proper position. When new ice is made, dispenser should operate.

Remove ice cubes that are jamming the dispenser.

Use the dispenser often so that cubes do not freeze together. The ice & water filter cartridge could be clogged.

Replace the filter cartridge. Dispensing system operates best at 20 - 100 psi water pressure. Well

water pressures should fall within this range.

+ 52 hidden pages