Frigidaire CGLMV169DBB, CGLMV169DQB, CGLMV169DSB, CPLMV169DCB, CPLMV169DCC Installation Guide

Installation

Overthe Range

Instructions

MicrowaveOven

BEFORE YOU BEGIN Read these instructions completely and carefully.

• IM PC RTANT- Savethese instructions for local

inspector's use.

• IMPORTANT- Observe all governing codes

and coordinates.

• Note to Installer- Be suretoleave these

instructions with the Consumer.

• Note to Consumer- Keep these instruc-

tions for future reference.

• Skill Level - Installation of this appliance

requires basic mechanical and electrical skills.

1 MOUNTING SPACE

Proper installation is the responsibility of the installer.
Product failure due to improper installation is not cov-

ered under the Warranty.

Please read all instructions thoroughly before installing
the Over the Range Microwave Oven. Two people are
recommended to install this product.

If a new electrical outlet is required, its installation
should be completed by a qualified electrician before the

Microwave Oven is installed. See 3 ELECTRICAL
GROUNDING INSTRUCTIONS on page 2.

2 WALL CONSTRUCTION

This Microwave Oven/Hood requires a mounting space on a
wall as shown in Figure 1. It is designed to be used with stan-
dard 12-inch wall cabinets.

l

Atleast2"

Backsplash.._,_<_ _ _,.

Figure 1

30"or morefrom

surface

66"or more
fromfloor

This Microwave Oven/Hood should be mounted against and
supported by a flat vertical wall. The wall must be flat for prop-
er installation. If the wall is not flat, use spacers to fill in the
gaps. Wall construction should be a minimum of 2" x 4" wood

studding and 3/8" or more thick dry wall or plaster/lath. The
mounting surfaces must be capable of supporting weight of 110
pounds--the oven and contents--AND the weight of all items
which would normally be stored in the top cabinet above the

unit.
The unit should be attached to a minimum of one 2" x 4"

wall stud or two 2" x 3" wall studs.
To find the location of the studs, one of the following methods

may be used:
A. Use a stud finder, a magnetic device which locates the nails

in the stud.

B. Use a hammer to tap lightly across the mounting surface to

find a solid sound. This will indicate stud location.

The center of the stud can be located by probing the wall with a
small nail to find the edges of the stud and then placing a mark

halfway between the edges. The center of any adjacent studs
will normally be 16" or 24" to either side of this mark.

NEED HELP?

For customers in the United States, call: 1-800-944-9044
For customers in Canada, call: 1-800-213-9397 (English)

1-800-668-4606 ext.8199 (French)

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

1 P/N316137334

TINSEB385MRR0

Installation Instructions

3 ELECTRICAL GROUNDING

INSTRUCTIONS

This appliance must be grounded. This oven is equipped with a
cord having a grounding wire with a grounding plug. It must be
plugged into a wall receptacle that is properly installed and

grounded in accordance with the National Electrical Code and
local codes and ordinances. In the event of an electrical short

circuit, grounding reduces risk of electric shock by providing an
escape wire for the electric current.

WARNING - Improper use of the grounding plug can result in a
risk of electric shock.

ELECTRICAL REQUIREMENTS

The oven is equipped with a 3-prong grounding plug. DO NOT
UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE

GROUNDING PIN FROM THE PLUG.
The Power Supply Cord and plug must be connected to a sep-

arate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit, sin-
gle grounded receptacle. The receptacle should be located
inside the cabinet directly above the Microwave Oven mounting
location as shown in Figure 2.

NOTE:

1. If you have any questions about the grounding or electrical
instructions, consult a qualified electrician or serviceperson.

2. Neither Electrolux nor the dealer can accept any liability for
damage to the oven or personal injury resulting from failure
to observe the correct electrical connection procedures.

4 HOOD EXHAUST DUCT

When the hood is vented to the outside, a hood exhaust duct is
required. All ductwork must be metal; absolutely do not use
plastic duct. Check that all connections are made securely.
Please read the following carefully:

Exhaust connection: The hood exhaust has been designed to
connect to a standard 3-1/4" X 10" rectangular duct. If round
duct is required, a rectangular-to-round adapter must be used.

Rear exhaust: If a rear or horizontal exhaust is to be used, care
should be taken to align the exhaust with the space between the

studs, or wall should be prepared at the time it is constructed by
leaving enough space between wall studs to accommodate

exhaust.
Maximum duct length: For satisfactory air movement, the total

duct length of 3-1/4" X 10" rectangular or 6" diameter round duct
should not exceed 140 feet.

Elbows, adapters, wall caps, roof caps, etc. present additional
resistance to air flow and are equivalent to a section of straight
duct which is longer than their actual physical size. When calcu-

lating the total length, add the equivalent lengths of all transi-
tions and adapters plus the length of all straight duct sections.
Figure 3 shows the approximate feet of equivalent length of
some typical ductwork parts. Use the values in parentheses for
calculating air flow resistance equivalent, which should total

less than 140 feet.

Ground

Receptacle 1_

Openingfor

PowerCord

Figure 2

90" ELBOW (10 FT.)

90" ELBOW (25 FT.)

45° ELBOW (5 FT.)

45_ ELBOW (5 FT.)

Figure 3

ADAPTOR (5 FT.)

WALL CAP (40 FT.)

10"WIDE ELBOW {10 FT.)

ROOF GAP (24 FT,)

Installation Instructions

5 TOOLS RECOMMENDED FOR

INSTALLATION

• Phillips Screwdriver

• Electric Drill

• 1/2", 5/8" and 3/32" Drill Bits

• 1-1/2" Wood Bit or Metal Hole Cutter
(if metal cabinet is used)

• Saw to cut exhaust opening (if needed)

• Protective Drop Cloth for product and range -

you may also use carton for protection

• Scissors

• Pencil

• Measure

• Tape

6 INSTALLATION HARDWARE

The INSTALLATION HARDWARE (items _1_ - (_) packed with
the oven should contain the following:

Item Name Quantity
@ Wood Screw 5 X 30 mm 6

® Toggle Bolt 3/16 inch 4
(_ Top Cabinet Screw 5 X 60 mm 2
@ Flat Washer 30 mm diameter 2

Power Cord Hanger 1

Grommet 1
(_ Tapping Screw 4 x 12 mm 4
(_ Exhaust Damper Assembly 1

(_ Charcoal Filter 1

7 PREPARATION OF THE OVEN

1. Open the bottom of the carton, bend the carton flaps back
and tilt the oven over to rest on plastic foam pad. Lift carton
off oven and remove all packing materials, Installation

Instructions, Wall Template, Top Template, Charcoal Filter,

Turntable and Turntable Support; however, DO NOT

REMOVE THE WAVEGUIDE COVER, which is located on

the ceiling in the oven cavity. SAVE THE CARTON AS IT
MAY MAKE INSTALLATION EASIER.

2. CHECK THE OVEN.
Check the oven for any damage, such as misaligned or bent

door, damaged door seals and sealing surfaces, broken or
loose door hinges and latches and dents inside the cavity or
on the door. If there is any damage, do not operate the oven
and contact your dealer or ELECTROLUX AUTHORIZED

SERVICER.

3. Remove and save Screws (A) as shown in Figure 5.

4. Pull the louver away from the unit and set aside.

5. Loosen the two Mounting Screws (D) which secure the
Mounting Plate to the rear side of the oven. Remove the
Mounting Plate. See Figure 6.

j (A)

Mounting

Plate

Control

Side

Sr_ruln_%_ tin rlr_n_%_ tin ru_/_oL_ _

_/ Use with metal cabinets. Surround (_ _

epowercordopening.Cuttofit.

® ®

Figure4

Parts shown not to common scale.

Figure 5

MountingPlate

f

(D) J

Figure 6