Frigidaire GLMB209D, GLMB209DS - 2.0 cu. Ft. Microwave Oven, PLMB209DC, MWTRMKT27, MWTRMKT30 Installation Instructions Manual
IMPORTANT - PLEASE READ
AND FOLLOW
THIS BUILT-IN KIT IS DESIGNED FOR USE ONLY
WITH ELETROLUX MICROWAVE OVENS SPECIFYING BUILT-IN KIT
MWTRMKT27 OR MWTRMKT30 ON THE RATING
LABEL ON THE LEFT SIDE WALL OF THE
MICROWAVE OVEN CAVITY.
IF YOUR LOWER CONVENTIONAL OVEN IS NOT
LISTED IN THE USE AND CARE MANUAL OF THE
MICROWAVE OVEN, THEN DO NOT INSTALL THE
MICROWAVE OVEN ABOVE IT OR IN ANY AREA
WHERE HEAT AND STEAM ARE GENERATED; FOR
EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL
RANGE.
Installation
Instructions
Built-in Trim Kit
MWTRMKT27 and MWTRMKT30
P/N 316137335
TINSEB384MRR0
BEFORE YOU BEGIN
• IMPORTANT – Save these instructions
for local inspector's use.
•
IMPORTANT – Observe all governing
codes and coordinates.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
•
Note to Consumer – Keep these
instructions for future reference.
• Skill level - Installation of this appliance requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
• Unplug the microwave oven before attempting
installation of this kit.
• Because the kit includes metal parts, caution
should be used in handling and installation to
avoid the possibility of injury.
•Do not remove permanently affixed labels, warn-
ings, or plates from the product. This may void
the warranty.
Read
these instructions completely and carefully.
QUESTIONS?
For customers in the United States call: 1-800-944-9044
For customers in Canada call: 1-800-213-9397 (English)
1-800-668-4606 ext.8199 (French)
Visit our Website at: www.frigidaire.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
FOR YOUR SAFETY:
WARNING – Before beginning the installation,
switch power off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
1
PARTS INCLUDED IN THE KIT
1. Front Frame Assembly - QTY 1
2. Exhaust Duct Assembly - QTY 1
3. Screw A - QTY 2
4. Screw B - QTY 4
CABINET OR WALL CUTOUT
Cutout Dimensions
Height (A)
Minimum 16
3
/4” (42.5 cm)
Maximum 17” (43.2 cm)
Width (B)
Minimum 24
3
/8” (61.9 cm)
Maximum 24
11
/16” (62.7 cm)
Depth (C)
Minimum 20” (50.8 cm)
ELECTRICAL OUTLET LOCATION
Outlet should NOT be in the shaded area as indicated on
Illustration 1
NOTE 1:
If the Depth (C) dimension is greater than 21” (53.3 cm),
the outlet location may be in any area on the rear wall.
NOTE 2:
The floor of the opening should be constructed of plywood strong enough to suppor t the weight of the oven
and floor load (approximately 100 pounds). The floor
should be level for proper operation of the oven. Be sure
to check the local building code as it may require that the
opening be enclosed with side, ceiling and rear partition.
The proper functioning of the oven does not require the
enclosure.
2
Installation Instructions
Illustration 1
Front Frame Assembly
Exhaust Duct Assembly
Screw A
Screw B
A
B
C
6”
(15.2 cm)
4”
(10.2 cm)
4”
(10.2 cm)
3
EXHAUST DUCT ASSEMBLY
1. Place the Exhaust Duct in the opening. When the
Exhaust Duct Assembly is in the opening correctly,
the flanges will be tightly against the lower edge of
the opening. See Illustration 2.
2. Secure the Exhaust Duct Assembly with the two
screws A.
IMPORTANT: Secure screws in outer hole.
FRAME INSTALLATION
1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet.
2. Carefully guide the assembled oven into the prepared opening. Slide the oven on the Exhaust Duct
Assembly. See Illustration 3. Avoid pinching the cord
between the oven and the wall. Adjust the position of
the oven so that the feet of the oven are fitted into the
recesses of the Exhaust Duct Assembly. See
Illustration 4.
3. Position the FRAME ASSEMBLY to be square with
the oven. Carefully place the FRAME ASSEMBLY
on the oven. Check that it is level and then secure
with two SCREWS B. See Illustration 5.
4. Secure the bottom portion of the FRAME ASSEMBLY with the two remaining SCREWS B. See
Illustration 5.
Illustration 2
Screw A
Screw A
Exhaust Duct
Assembly
Flanges
Installation Instructions
Illustration 4
Exhaust Duct Assembly
Illustration 3
Foot
Recess
Illustration 5
Screw B
Screw B
Screw B
Screw B
4
Installation Instruction Notes
Loading...