Page 1
Installation
Built-In TrimKits
82-1827and82-1830
Instructions
I Questions?ln the U.S., call 1-800-944-9044. In Canada, call 1-866-213-9397(English),1-800-669-4606 ext. 8199 (French). Visitour Websiteat:www.frigidaire.com I
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - Savethese
instl_uctions for 1(cal inspect( r s use.
• IMPORTANT - Obse,_'eall
governing codes and ordinances.
• Note to Installer - Be sure toleavethese
instructions with the Consumer.
• Note to Consumer - Keep these
instl_uctions for future reference.
FOR YOUR SAFETY:
WARNING - _f,,rebeginning the
installation, switch power off at service panel and lock
the smwice disconnecting means to prevent power
from being switched on accidentally. When Ihe selwice
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
smwice panel.
TOOLS YOU WILL NEED
• Unplug the microwave oven before attempting
inslatladon of this kit.
• Skill level- Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time - 1-3 hours
• Proper insmtladon is flae rcsponsibilily of the installer.
• Product failure due to improper installation is not
covered under the Warranty-.
• This kit is UL and CUL listed for installation alone or
over any Frigidaire single electric wall oven.
PARTS INCLUDED
PART QUANTITY
TrimFrame 1
BottomDuct 1
SideDuct 1
Phillipsscrewdriver
Drillwith _41*bitor #35
Pencil
Awl orpunch Tapemeasure
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
164D3370P160
49-40169-1
P/N 316137209 Rev. A
Prinwd in Korea (05-01 JR)
1" Screws 6
(4required,2extra)
V2"Screws 15
(11required,4 extra)
Anti-TipBracket 1
BottomBracket 1
UpperDuct 1
Template 1
1
Page 2
Installation Instructions
CUTOUT DIMENSIONS
Models 27" 30"
(68.6 cm) (76.2 cm)
Height 16_/_" 163/4"
(42.5 cm) (42.5 cm)
Width 25W' 25_//'
(6.5 cm) (6.5 cm)
Depth (min.)* 19_k"or 22" 19W' or 22"
(49.5 cm or (49.5 cm or
56 cm) 56 cm)
• , • , • I Jt
• Mm.depflawlflarecep_leoulslde(abmet19/2 (49.5 cm).
Min. depth wilh re_epla( le inside _abine122" (56cm).
Depth
Height
INSTALL BOTTOM BRACKET
AND BOTTOM DUCT
[] Disconnect the microwave oven before proceeding
with the installation.
[] Faslen lhe botlom bracket to the bottom duct by
using two V2"screws.
_ ½"Screws{2)
[] Remove any loose items inside the microwave oven,
including the turntable and turntable support.
Carefully turn the microwave upside down.
] . 1 /t
Install bottomductw_th four/2 screws as shown.
'r_ Screwws _Screws
i
i
3" Min.
(7.6cm)
On 27" (68.6 cm) models, allow 1" (2.5 cm) at the lop,
HA€,"(1.75 cm)on the sides and I_A" (3.5 cm)at the
bottom for overlap of the Trim Frame over the edges
of the cutout.
On 30" (76.2 cm) models, allow 1" (2.5 cm) at lhe lop,
2:V_,"(5.6 cm) on the sides and I:V_"(3.5 cm) at the
bottom for overlap of the Trim Frame over the edges
of the cutout.
Microwave Oven Upside Down
2
Page 3
Installation Instructions
[_] INSTALL THE ANTI-TIP BRACKET
[] Fold or cut the fl'ont edge of the template, along the
front guide line. Place the template flush along the
front edge of the cutout floor, aligning the center
line of the template with the center line of the
cutout floor. Mark the center positions with an awl
or center punch for the anti-tip bracket location
as shown.
Cutout Floor
[] Remove the template and drill two holes for the
anti-tip bracket.
g _/_"Screws(2} g
[] Install the anti-tip bracket onto the cutout floor
• /t ,
usmgtwo _/2 sclews.
[_] INSTALL SIDE DUCT AND
UPPER DUCT
[] Connect the side duct to the upper duct as shown.
1. Insert projecting labs of the upper duct into the
holes of Ihe side duct.
2. Bend the tabs up with caution as shown.
NOTE: Remove any oil or dirt on the surface of the
microwave oven before the ducLs are attached.
UpperDuct
-J_ L 3Tabs
i1) (2)
SideDuct
[]
Set the microwave upright, being careful not to
bend the front flange. Remove the one existing
screw from the left side of the microwave oven.
[]
Peel off the backing of Ihe double sided lape.
Carefully position the side duct and upper duct
assembly on the microwave cabinet, aligning wida
the bottom screw hole. Press down firmly on the
ducts. Fasten the duct assembly to the left side of
the cabinet with the screw removed above.
3
Page 4
Installation Instructions
[_] INSTALL MICROWAVE OVEN
INTO CABINET
[] Slide the microwave oven part way into the cabinet
opening.
BottomDuct _ Anti-TipAssembly
Anti-_p
Bracket
BottomBracket
[] Plug in the microwave oven.
[]Bottom bracket must be flat to dae cutout floor to
engage correctly wida Ihe ann-tip bracket as shown.
Carefully slide flae microwave back, making sure the
power cord is not mashed or cut.
[] Center the microwave oven within Ihe cutout
opening and slide dae microwave oven in place,
engaging the anti-tip bracket.
[] Ensure the microwave oven is accurately centered.
I-_ INSTALLING THE TRIM FRAME
[] Place the tlJm frame over the microwave oven.
[] Make sure the trim frame is level and the microwave
oven is centered within the tlim frame. Mark four
center positions through the four mounting holes
of the trim frame.
NOTE: Center the tIim frame equally on all four
sides.
[] Remove the u_im frame and drill four pilot holes.
PilotHole
CutoutOpening
1" Screw
TrimFrame
MountingHole
i/),,Screw
[] Drill pilot holes through the posidoning flange and
then install three /2 screws at the front of the
bottom duct as shown.
PositioningFlange
i tt
[] Attach the trim frame by using four screws.
[_ REPLACE ANY LOOSE ITEMS
[] Your trim kit is now fully installed, Replace any
loose items that were removed fi'om the inside of
the microwave oven.
[] Keep these installation instructions for future
reference,
[] Replace house fuse or close circuit breaker.
4
Loading...