Frigidaire GLGR1042FC1 Owner’s Manual
OPERATING INSTRUCTIONS
DRY TEMPERATURE END OF CYCLE PRESS SAVER START
PERM PRESS/COLORS KNITS/DELICATES
MEDIUM HEAT LOW HEAT ON OFF
HIGH HEAT NO HEAT
REGULAR/WHITES _ AIR FLUFF O
Before Operating Your Dryer
Read your dryer Owner's Guide. It hasimportant 5.
safety and warranty information. It also has many
suggestions for best drying results. 6,
To reduce the risk of fire, electric
shock, or injury to persons, read the IMPORTANT 7.
SAFETYINSTRUCTIONSin your dryer owner's guide
before operating this appliance.
Operating Steps
Read Drying Procedures in your Owner's Guide.
It explains these operating steps in detail.
1. Prepare items for drying.
2. Check that lint screen is clean and in place.
3, Load the dryer. If desired, add a dryer fabric
softener sheet.
4. Close the dryer door.
10. Clean lint screen after every load.
Temperature Selection
Always follow directions on fabric care
labels.
to dryitems containing feathers or down, foam rubber,
plastics, or similarly textured, rubber-like materials.
Use Air Fluff-No Heat setting only.
YES NO
Set Dry Temperature control Select PRESS
SAVER if desired.
Turn cycle selector clockwise to desired
setting.
Start dryer. Pushthe Start button and hold for 1-
2 seconds, or turn the Turn to Start control
clockwise to ON.Holdfor 1-2secondsand release.
8. A signal will sound toward the end of the
cool down period when the End of Cycle
Signal is ON.
9. Remove items immediately and hang orfold.
To avoid fire hazard, do not use heat
AUTO PERM PRESS/ AUTO REGULAR/
COLORS WHITES
TIMED DRY 50
10
20
3O
PRESS SAVER MORE
60
AUTO KNITS/
DELICATES
The REGULAR-HIGH HEA T, PERM PRESS-MEDIUM
HEAT,and KNITS/DELICATES-LOW HEATtemperature
settings may be used with any cycle setting. The AIR
FLUFF-NO HEATsetting can be usedonly inthe Timed
Dry cycle.
AIRFLUFF=NO HEATsetting tumbles the load without
heat. Use Air Fluff to freshen clothing, pillows or
blankets, or to dust draperies.
Cycle Selection
Turn cycle selector clockwise to desired cycle and
setting.
Each cycle ends with a cool down period. The heat
automatically turns off and the load continues to turn ble
during the cool down period. Thisreduceswrinkling and
makes items easierto handle during unloading.
Drying time varies depending on size and dampness of
load, weight and fabric type. Room temperature and
humidity, type of installation and electrical voltage or
gas pressure can also affect drying time.
Printed in U.S.A. P/N134843000A(0611)
DRY TEMPERATURE END OF CYCLE PRESS SAVER START COLORS PRESSSAVER WHITES
PERM PRESS/COLORS KNITS/DELICATES
MEDIUM HEAT LOW HEAT ON OFF
HIGH HEAT NO HEAT
AUTO PERM PRESS/ AUTO REGULAR/
MORE
YES NO
REGULAR/WHITES O AIR FLUFF O
Cycle Selection continued
Auto Regular Cycle
This cycle is best for cotton items. Drying time is
determined automatically at the temperature selection
of your choice.
• High heat issuggested for cotton items.
Initially set cycle selector on NORMAL DRY.
For items requiring more drying time, set cycle
selector on MORE,
For items requiring lessdrying time, set cycle
selector on LESS,
Auto Delicate Cycle
Thiscycleisbestfor knit and delicate items. Drying time
isdetermined automatically atthetemperature selection
of your choice.
Low heat is suggested for knit and delicate items.
Initially set cycle selector on NORMAL DRY.
For items requiring more drying time, set cycle
selector on MORE.
For items requiring lessdrying time, set cycle
selector on LESS.
A signalwill sound toward the end of the cool down
period when the Cycle Signal isON.
If the Press Saver option isturned to YES,the cycle
selector will advance to the Press Saver setting.
Unheated tumbling continues during PressSaverfor
16 minutes to helpreducewrinkling ifthe dried load
cannot be removed promptly. A signal will sound
briefly every five minutes asa reminder to remove
the load when the Cycle Signal is turned on.
Timed Dry Regular Cycle
Thiscycleprovides approximately 60 minutes of drying
time at the temperature selection of your choice.
Auto Perm Press Cycle
This cycle is best for permanent press items. Drying
time is determined automatically at the temperature
selection of your choice.
Medium heat is suggested for permanent press
items.
Initially set cycle selector on NORMAL DRY.
For items requiring more drying time, set cycle
selector on MORE,
Foritems requiring lessdrying time, set cycleselector
on LESS.
10
20
30
TIMED DRY 50 DELICATES
40 AUTO KNITS/
60
A signal will sound toward the end of the cool down
period when the Cycle Signal is ON.
If the Press Saver option is turned to YES,the cycle
selector will advance to the Press Saver setting.
Unheated tumbling continues during Press Saver
for 16 minutes to help reduce wrinkling if the dried
load cannot be removed promptly. A signal will
sound briefly every five minutes as a reminder to
remove the loadwhen the CycleSignal isturned on.
Energy Saving Tips
Keep the lint screen clean and exhaust the dryer
correctly.
Sortlaundry properly and select proper temperature
and cycle settings. Choose an automatic dry cycle
whenever possible for accurate drying time.
Dry only full loads. Single items and small loads
usually take longer to dry.
Avoid overloading, adding wet items to a partially
dry load, and overdrying.
Dry one load after another to take advantage of a
warm dryer.
Opening the door needlessly causes warm air to
escape,which prolongs drying time.
If possible, use the dryer on low humidity days.
Install the dryer in an area where the room
temperature is at least 45% (7°C).
P/N134843000A (0611)
Loading...