Frigidaire GLEB30S8CBB, GLEB30S8CQB, GLEB30S8CSB, PLEB27S8ACA, PLEB27S8CCB Installation Guide

...

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

_'l_IW_,_:t_ll_[elFOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

Your new wall oven has been designed to fit a limited variety of cutout sizes to make the job of installing easier. The first step of your installation should be to measure your current cutout dimensions and compare them to the cutout dimensions chart below for your model. You may find little or no cabinet work will be necessary.

Do not remove spacers (if equipped) on the

side wails and/or on the back of the built-in oven. These spacers center the oven in the space provided. The oven

must be centered to prevent excess heat buildup that may result in heat damage or fire.

NOTE: Base must be capable of supporting

150 pounds (68 kg).

** NOTE: Allow at least 19 3/8" (49.2 cm) clearance for door depth when it is open.

NOTE: Dimension G is critical to the proper installation of the built-in oven. If the oven

decorative moulding does not but against

** Door Open

(see note)

the cabinet, or if noise is heard on convection models, verify dimension G to assure it is according to the required

dimension.

NOTE: For a cutout height greater than H Min. dimension add one 2" (5 cm) wide

wood shim to each side of the opening under the appliance side rails.

27" AND 30" WALL OVENS

1 I/2"

2" (5 cm)

Spacer if Needed

* Suggested distance from floor is 31 " (78.7 cm).

Minimum required distance is 4 _/2" (11.4 cm)

Figure 1 • Dimension for stainless steel models.

Hole for

tble

Hole for

Cable

Junction Box

Electrical

(7.6 cm) Max

All dimensions are in inches (cm). Some models are not available in Canada.

P/N 318201507 (0201) Rev. C

English - pages 1-6

Espa_ot - p_tginas 7-13 Eran_ais - pages 14-20

Important Notes to the Installer

1. Readall instructions contained in these installation instructions before installing the wall oven.

2. Remove all packing material from the oven compartments before connecting the electrical supply

to the wall oven.

3. Observe all governing codes and ordinances.

4. Besure to leavethese instructions with the consumer.

5. Oven door may be removed to facilitate installation.

6. THESEOVENS ARE NOT APPROVED FOR

STACKABLEOR SIDE=BY=SIDEINSTALLATION.

Important Note to the Consumer

Keep these instructions with your Owner's Guide for future reference.

IMPORTANT SAFETY INSTRUCTIONS

• Be sure your wall oven is installed and grounded properly by a qualified installer or service

technician.

• This wall oven must be electrically grounded in

accordance with local codes or, in their absence, with the National Electrical Code ANSI/NFPA

No.70- latest edition in United Sates, or with CSA

Standard C22.1, Canadian Electrical Code, Part 1, in Canada.

Stepping, leaning or sitting on the

door of this wall oven can result in serious injuries and can also cause damage to the wall oven.

Observe all governing codes and local ordinances

1. A 3-wire or 4-wire single phase 120/240 or 120/208 Volt, 60 Hz AC only electrical supply is required on

a separate circuit fused on both sides of the line (time-delay fuse or circuit breaker is recommended).

DO NOT fuse neutral. The fuse size must not exceed

the circuit rating of the appliance specified on the

nameplate. Consideration must be given for a

combination built-in oven and cooktop refer to unit serial plate of each.

NOTE: Wire sizes and connections must conform with

the fuse size and rating of the appliance in accordance with the American National Electrical Code ANSI/NFPA

No. 70-latest edition, or with Canadian CSA Standard

C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

_l_l'_v-'_;t_ll_[d An extension cord should not be used

with this appliance. Such use may result in a fire, electrical shock, or other personal injury.

2. These appliances should be connected to the fused disconnect (or circuit breaker) box through flexible

armored or nonmetallic sheathed cable. The flexible armored cable extending from the appliance should

be connected directly to the junction box. The junction box should be located asshown in figure 1 and with as much slack as possible remaining in the cable between the box and the appliance, so it can

be moved if servicing is ever necessary.

3. A suitable strain relief must be provided to attach the flexible armored cable to the junction box.

• Never use your wall oven for warming or heating the room. Prolonged use of the wall oven without adequate ventilation can be dangerous.

The electrical power to the oven must

be shut off while line connections are being made. Failure to do so could result in serious injury or

death.

1. Carpentry

Refer to figure 1 for the dimensions applicable to your appliance, and the space necessary to receive the oven. The oven support surface may be solid plywood or

similar material, however the surface must be level from side to side and from front to rear.

2. Electrical Requirements

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse, having amperage as noted on the rating plate (the

rating plate is located on the oven frame).

Electrical Shock Hazard

• Electrical ground is required on this appliance.

• Do not connect to the electrical supply until appliance is permanently grounded.

• Disconnect power to the junction box before

making the electrical connection.

• This appliance must be connected to a grounded, metallic, permanent wiring system,

or a grounding connector should be connected to the grounding terminal or wire lead on the

appliance.

• Do not use a gas supply line for grounding the appliance.

Failure to do any of the above could result in a

fire, personal injury or electrical shock.

Wait at least three (3) hours after

receiving this built-in oven before switching the power on

to prevent possible damage to the built-in oven control at power on.

3. Adjusting Oven Height

Oven height can be adjusted with 2" (5 cm) wide wood shims when needed to fit into an existing cabinet cutout opening, when cutout height exceeds H Min. dimension (see Figure 1)

rl WL'_Vl_*1:t_11;[€

Improper connection of aluminum

house wiring to copper leads can result in a short

circuit or fire. Use only connectors designed for joining copper to aluminum, and follow the

manufacturer's recommended procedure closely.

4. Electrical connection

It is the responsibility and obligation of the consumer to

contact a qualified installer to assure that the electrical

installation is adequate and is in conformance with the National Electrical Code ANSI/NFPA No 70-latest edition,

or with CSA Standard C22.1, Canadian Electrical Code,

Part 1, and local codes and ordinances

Electrical ground is required on this appliance.

These appliances are equipped with a copper conductor flexible cable. If connection is made to aluminum house

wiring, use only special connectors which are approved for joining copper and aluminum wires in accordance

with National Electrical Code and local codes and ordinances.

These appliances are manufactured with a white neutral

power supply wire and a frame connected green or bare

copper grounding wire

If local codes permit connection of the frame grounding conductor to the neutral (white) wire.

(The 3-conductor cord or cable must be replaced with a 4-conductor cord or cable where grounding through the neutral conductor is prohibited in new

installations, mobile homes, recreational vehicles or in other areas where local codes do not permit

neutral grounding)

Connect the green (or bare copper) wire and the white wire from the appliance cable to the supply

cable ground wire (white or bare) inside the junction

box. Connect the remaining wires inside the junction box from the power supply cable to the matching

colors of the appliance cable wires (figure 2)

Cable from Power Supply

Ground Wire _ b-_ Wires

Red ]

Wires

Ground Wire _ _ U±_sted Conduit (Bareor Green Wire)_ _ _ Co-r_n-e_or(or CSA listed)

Cable from appliance

Figure 2

3-WIRE GROUNDED JUNCTION BOX

Black

Junction Box

Wire

2. If used in mobile homes or if local codes DO

NOT permit connection of the frame grounding

conductor to the neutral (white) wire, separate

the white and bare copper ground wires that extend out of the end of the supply cable of the appliance

Connect the white wire from supply cable to the

neutral white wire in the junction box. Connect the black and red wires from the supply cable to the

matching color wires in the junction box. The bare

wire must now be used to ground the appliance in accordance with local electrical codes. Connect the

bare copper ground wire to the grounded lead in the

service panel DO NOT ground to a gas supply pipe

DO NOT connect to electrical power supply until

appliance is permanently grounded. Connect the ground wire before turning on the power (figure 3)

Cable from Power Supply

Ground Wire_

Red --

Wires

Ground Wire

Bareor Green Wire)_

Junction Box UL-Lsted Conduit

Cable from appliance

White Wire

Black Wires

Connector (or CSA listed)

Figure 3

4-WIRE GROUNDED JUNCTION BOX

If connecting to a 4-wire electrical

system (mobile homes), the appliance frame MUST

NOT be connected to the neutral wire of the 4-wire

electrical system.

NOTE TO ELECTRICIAN: The armored cable leads

supplied with the appliance are CSA-recognized for connection to larger gauge household wiring. The

insulation of the leads is rated at temperatures much

higher than temperature rating of household wiring. The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire,

rather than the wire gauge alone

Do not lift the oven by the door handle.

5. Cabinet Installation

A. 27" Wall Oven

Insert appliance into cutout. Use the screws provided to fasten the front frame of the appliance to the cabinet. The mounting holes in the front frame of appliance may be used as a template to locate the appliance mounting screw holes.

To fasten the appliance to the cabinet:

1. Line up the 2 mounting holes on the decorative trim (ventilation) (taped to the oven side panel) with the lower mounting holes on each side of the oven frame, below the oven door (see figure 4).

2. Use 2 screws from the miscellaneous parts bag to secure the decorative trim (ventilation) and

appliance to the cabinetry.

3. Use the remaining 2 screws for mounting the appliance in the upper two mounting holes on

each side of the oven frame, above the door.

MOUNTING

:REW

DECORATIVETRIM

VENTILATION)

MOUNTING SCREW

Figure 4

driver (square drive preferred, however a No. 2

Phillips@or Quadrex@ screw driver can also be used). (If not removed, open the door to remove the

screws, located at the upper end of the side trim).

3. Insert the unit into the cabinet opening. Slide unit inward leaving 1 3/s" (3.5 cm) clearance between

the oven decorative trim and cabinet. Pull the armored cable through the hole in the floor and

toward the junction box while moving the appliance

inward. Usethe second set of holes in the side frame

of the unit asa guide to find the position of the anti- tip brackets on the sides of the cabinet opening.

Mark the position of the anti-tip brackets asshown in Figure 5.

4. Pull out the oven approximately 1foot (30.5 cm)

away from the cabinet. Reposition each bracket on the cabinet and drill 1/8" pilot holes. Fasten the

brackets in place using the 2 screws supplied (#10 x 1%" long).

If needed, add wood spacers at the anti-tip bracket locations to reduce the cabinet opening to 28 1/2"

(72.4 cm).

Now push the unit in and against the cabinet, then

attach the unit to the anti-tip brackets using the 2 screws removed earlier from the side frame.

5. Fortypical under counter installation of an electric built-in oven with an electric cooktop above, see

Figure 6.

6. Fortypical under counter installation of an electric built-in oven with agas cooktop mounted above, see

Figure 7.

4. For typical Under counter installation of an electric built-in oven with an electric cooktop mounted

above, see Figure 6.

5. For typical under counter installation of an electric built-in oven with a gas cooktop mounted above,

see Figure 7.

B. 30" Wall Oven

The wall oven can tip when the

door is open. The anti-tip brackets supplied with

the wall oven must be attached to the cabinet

and the appliance to prevent tipping of the wall oven and injury to persons.

Anti-Tip Brackets Installation Instructions

1. Unpack the wall oven and find the 2 anti-tip screws included in the literature package. The door

may be removed to facilitate handling (see the

Owner's Guide for instructions).

2. The anti-tip brackets are temporarily installed under the decorative side trims of the oven when shipped (see Figure 5). Remove the anti-tip brackets from the

unit side frame using a No. 2 Robertson@ screw

Cutout Dimensions

29" (73.7 cm) Max.*

28 1/2" (72.4 cm) Min.* I_

28 1/16" (71.3 cm) Min. |

_4 29 5/8" (75.2 cm)Max. II_ I 271/4"

• _ [ll(71.8cm) Min. f / IJ_Jl 28 7/8"

71 / /" 73.3cm/Mox.

/ / Anti-Tip Brackets i | 22"

21 1/4'1'(559 cm)

1 ,

-.:e::j--

* RecommendedCutout Width is28 1/2" (72.4 cm)

Figure 5

Only certain cooktop models may be installed over cer- tain built-in electric oven models, listed by the MFG ID

number (seethe insert sheet included in the literature package).

To reduce the risk of

personal injury and

tipping of the wall oven, the wall oven

must be secured to the cabinet (s)by anti- tip brackets.

208/240 Volt junction box

for built-in oven.

Side filler panels are necessary to iso- late the unit from adjoining cabinets. Panel height should allow for installa- tion of approved cooktop models.

Approx. 3"

(7.5 cm)

36" Min. (91.4 cm) Min.

Use 3/4" (1.9 cm) plywood, installed

on two runners, flush with toe plate.

Must be capable of supporting 150 pounds (68 kg).

* If no cooktop is installed directly over

the oven unit, 5" (12.7 cm) maximum

isallowed above the floor.

Figure 6 - TYPICAL UNDER COUNTER INSTALLATION OF AN ELECTRICBUILT-INOVEN

WITH AN ELECTRICCOOKTOP MOUNTED ABOVE

Cut an opening in wood base minimum 9" x 9" (23 X 23 cm), 2" (5 cm) from left side filler panel, to route armoured cable to junction box.

4 1/2" (11.5 cm) Max.*

27" (686cm) 24 7/8" (632cm) Min 28 1/8" (714cm) Min

Wall Oven 25 1/4" (64.1 cm) Max 23 I/2" (597 cm) Min 28 5/8" (727 cm) Max

30" (762cm) 28 1/2" (724cm) Min 28 1/4" (718cm) Min

Wall Oven 29" (737 cm) Max 24" (61 cm) Min 28 7/8" (733 cm) Max

Flexible Appliance Cc

Wall Oven Cabinet

Figure 7 - TYPICAL UNDER COUNTER INSTALLATION OF AN ELECTRICBUILT-INOVEN

filler panel

WITH A GAS COOKTOP ABOVE

18"(45.7 cm) Max. _I

Flare Outlet

Union

Pressure Regulator

_ Manual

120V/6OHz

Grounded

Shutoff

Valve

Right Side

of Cabinet

(To be

accessible

for shut-off

valve

operation)

6. Checking Operation

Some wall ovens model have Manually Operated Control Knobs to set the clock and the oven bake, broil

convection (some models) or clean functions. Refer to the "Owner's Guide" otto the "Oven Control Guide"

supplied in the literature package and check all controls for correct operation.

If your model is equipped with an Electronic Oven

Control. Each of the functions has been factory checked

before shipping. However, it is suggested that you verify

the operation of the electronic oven controls once more.

Refer to the Owner's Guide or to the Oven Control Guide

for operation. Follow the instructions for the Clock, Timer, Preheat, Bake, Broil Convection (some models)

and Clean functions.

Bake-After setting the oven to 350°F/177°C for baking,

the lower element in the oven should become red.

Broil-When the oven is set to BROIL, the upper element in the oven should become red.

Clean-When the oven is set for a self-cleaning cycle, the

upper element should become red during the preheat portion of the cycle. After reaching the self-cleaning

temperature, the lower element will become red.

Convection (some models )-When the oven is set for a convection baking or roasting, both elements cycle on and off alternately and the convection fan will turn. The

convection fan will stop turning when the oven door is opened during convection baking or roasting.

IMPORTANT NOTE: A fan inside the upper rear part above the oven (some models) provides additional

cooling of the oven electrical and electronic components. The fan will continue to run after the oven has been

operating at high temperatures.

Model and Serial Number Location

The serial plate is located along the side of the oven door in the open position.

When ordering parts for or making inquires about your oven, always be sure to include the model and serial

numbers and a lot number or letter from the serial plate

on your oven.

Before You Call for Service

Read the Avoid Service Checklist and operating

instructions in your Owner's Guide. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials

in this appliance.

Refer to the warranty in your Owner's Guide for our toIF free service number and address. Please call or write if

you have inquiries about your product and/or need to order parts.

+ 14 hidden pages