All about the
Use& Care
of your
Room Air Conditioner
TABLE OF CONTENTS
Important Safety Instructions ...............................
FCC Statement
Product Registration
Packaging
Normal Sounds
Air Conditioner Features
www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352
.....................................................
.............................................
...........................................................
....................................................
.......................................
2-4 21-7
5
6
6
6
7
Operating Instructions .........................................
Care and Cleaning
Energy Saving Ideas ...........................................
Before You Call ...................................................
Major Appliance Limited Warranty ........................
..............................................
13
13
. 14
15
16120300A23792
(June 2009)
Important Safety Instructions
NOTE:
This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as
instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that
may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.
NOTE:
The power supply cord with
this air conditioner contains a current
detection device designed to reduce the risk
of fire.
Please refer to the section ‘Operation of
Current Device’ for details.
In the event that the power supply cord is
damaged, it cannot be repaired. It must be
replaced with a cord from the product
manufacturer.
WARNING
Avoid fire hazard or electric shock. Do not
use an extension cord or an adaptor plug. Do
not remove any prong from the power cord.
Grounding type wall
receptacle
Do not, under any
circumstances, cut,
remove, or bypass the
grounding prong.
Power supply cord
with 3-prong grounding
plug and current
detection device
WARNING
For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. Read product labels for flammability and other warnings.
WARNING
Prevent Accidents
To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner,
follow basic precautions, including the following:
Be sure the electrical service is adequate for the model you have chosen. This information
can be found on the serial plate, which is located on the side of the cabinet and behind the
grille.
If the air conditioner is to be installed in a window, you will probably want to clean both
sides of the glass first. If the window is a triple-track type with a screen panel included,
remove the screen completely before installation.
Be sure the air conditioner has been securely and correctly installed according to the
separate installation instructions provided with this manual. Save this manual and the
installation instructions for possible future use in removing or reinstalling this unit.
When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front
and rear coils.
WARNING
Electrical Information
The complete electrical rating of your new room air conditioner is stated on the serial plate.
Refer to the rating when checking the electrical requirements.
Be sure the air conditioner is properly grounded. To minimize shock and fire hazards,
proper grounding is important. The power cord is equipped with a three-prong grounding
plug for protection against shock hazards.
Your air conditioner must be used in a properly grounded wall receptacle. If the wall
receptacle you intend to use is not adequately grounded or protected by a time delay fuse
or circuit breaker, have a qualified electrician install the proper receptacle.
Do not run air conditioner without outside protective cover in place. This could result in
mechanical damage within the air conditioner.
Do not use an extension cord or an adapter plug.
SAFETY PRECAUTIONS
DANGER! Avoid Serious Injury or Death
This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.
Do not insert or place fingers or objects into the air discharge area in the front of the unit.
Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.
Do not cut or damage the power cord.
If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.
In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized
Electrolux servicer.
Do not operate the air conditioner with wet hands.
Do not pull on the power cord.
Do not drink any water that is drained from the air conditioner.
2
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Important Safety Instructions
SAFETY PRECAUTIONS
CAUTION! Avoid Injury or damage to the unit or other property
Provide ventilation per installation instructions.
Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively.
Do not climb on or place objects on outdoor part of the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.
Periodically check the condition of the unit’s installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp metal edges.
Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading to possible electric shock.
When cleaning the unit, first make sure that the power and circuit breaker are turned off.
READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.
Unit must be upright for one hour prior to operating.
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
Plug in the Air Conditioner.
The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
Plug in &
press RESET
notice a click as the RESET button pops out.
Press the RESET button. Again you will notice a click as the button engages.
The power supply cord is now supplying electricity to the unit. (This is also indicated by a light
on the plug head).
NOTE:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained
from the product manufacturer.
Explanation of symbols displayed on the unit
WARNING
CAUTION
This symbol shows that this appliance used a flammable refrigerant. If the refrigerant is leaked
and exposed to an external ignition source, there is a risk of fire.
This symbol shows that the operation manual should be read carefully.
CAUTION
CAUTION
This symbol shows that a service personnel should be handling this equipment with reference
to the installation manual.
This symbol shows that information is available such as the operating manual or installation
manual.
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
3
Important Safety Instructions
WARNING FOR FLAMMABLE REFRIGERANT
'RQRWXVHPHDQVto accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
7KHDSSOLDQFHVKDOO be stored in a room without continuously operating ignition sources (for example: open flames, an operating
gas appliance) and ignition sourcesor (for example:an operating electric heater) close to the appliance. The appliance shall be
stored in a room without continuously operating ignition sources (for example: open flames, an operating gas appliance or an
operating electric heater).
'RQRWSLHUFHRUEXrn.
%HDZDUHWKDWWKHUHIULJHUants may not contain an odour.
&RPSOLDQFHZLWKQational gas regulations shall be observed.
.HHSYHQWLODWLRQRSenings clear of obstruction.
7KHDSSOLDQFHVKDOO be stored so as to prevent mechanical damage from occurring.
$ZDUQLQJWKDWWKHappliance shall be stored in a well-ventilated area where the room size corresponds to the room area as
specified for operation.
$Q\SHUVRQZKRLVinvolved with working on or breaking into a refrigerant circuit should hold a current valid certificate from an
industry-accredited assessment authority, which authorises their competence to handle refrigerants safely in accordance with an
industry recognised assessment specification.
6HUYLFLQJVKDOORQO\ be performed as recommended by the equipment manufacturer. Maintenance and repair requiring the
assistance of other skilled personnel shall be carried out under the supervision of the person competent in the use of flammable
refrigerants.
'2127PRGLI\WKe length of the power cord or use an extension cord to power the unit.
'2127VKDUHDVLngle outlet with other electrical appliances. Improper power supply can cause fire or electrical shock.
3OHDVHIROORZWKHLQstruction carefully to handle, install, clear, service the air conditioner to avoid any damage or hazard.
Flammable Refrigerant R32 is used within air conditioner. When maintaining or disposing the air conditioner, the refrigerant
(R32 or R290) shall be recovered properly, shall not discharge to air directly.
1RDQ\RSHQILUHRU device like switch which may generate spark/arcing shall be around air conditioner to avoid causing ignition of
the flammable refrigerant used. Please follow the instruction carefully to store or maintain the air conditioner to prevent
mechanical damage from occurring.
)ODPPDEOHUHIULJHUDQW5LVXVHGLQair conditioner. Please follow the instruction carefully to avoid any hazard.
CAUTION
7KLVDSSOLDQFHLVQot intended for use by persons (including children) with reduced physical ,sensory or mental capabilities or lack
of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
&KLOGUHQVKRXOGEHsupervised to ensure that they do not play with the appliance.
,IWKHVXSSO\FRUGLs damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
7KHDSSOLDQFHVKDOO be installed in accordance with national wiring regulations.
4
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
FCC Statement
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by tuning the device off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the equipment into an outlet other than the one used for the receiver.
Consult the dealer or an experienced radio/TV technician for assistance.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Host device Labeling
This device includes the following module.
Contains FCC ID: 2AIBX-NIU5L
RF exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum 20 cm between the radiator and your body. This transmitter must not be collocated or
operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.
INDUSTRY CANADA (IC) STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the
radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna
or transmitter.
l'exposition aux RF
L’antenne (ou les antennes) doit être installé e de façon à maintenir à tout instant une distance minimum de au moins 20 cm entre la
source de radiation (l’antenne) et toute personne physique.
Host device Labeling
This device includes the following module.
Contains IC: 21700-NIU5L
Host dispositif d'étiquetage
Ce dispositif inclut le module suivant.
Contient module émetteur IC: 21700-NIU5L
This is the location
of the module.
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
5
Product Registration, Packaging & Normal Sounds
Product Registration
Packaging
Record Your Model and Serial Numbers
Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the outside of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Remove all packaging from inside the carton, along with any
inserts placed into the side louvers.
PACKAGING INSERTS
Normal Sounds
Sound of Rushing Air
At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.
Gurgle/Hiss
“Gurgling or hissing” noise ma
heard due to refrigerant passing
through evaporator during normal
operation.
High pitched Chatter
Today’s high efficiency compressors
may have a high pitched chatter
during the cooling cycle.
y be
Noise when unit starts
A “da-da” sound may occur when the
unit is turned on in thirty seconds due
to the compressor starting (For Inverter
type). It is normal.
Vibration
Unit may vibrate and make noise
because of poor wall or window
construction or incorrect installation.
Pinging or Swishing
Droplets of water hitting condenser
during normal operation may cause
“pinging or swishing” sounds.
Note: Don’t try to drill any holes
on the base pan to eliminate the
normal sounds, otherwise it will
void the warranty.
6
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Air Conditioner Features & Operating Instructions
Air Conditioner Features
TURNS UNIT
ON OR OFF
SET
SWING
*Refer to the Quick Start Guide that came with your Smart Air Conditioner for detailed instructions on setting up your air
conditioner for connected operation from your smart phone or tablet.
REMOTE CONTROL
SET MODE
TO REPLACE BATTERY
Battery Size: CR2025
Turn Remote Control upside down. Squeeze tab
and pull to remove battery tray. Place battery in
tray with POSITIVE(“+”) side facing UP,
according to diagram. Re-insert battery tray.
ELECTRONIC CONTROL
Before you begin, thoroughly familiarize yourself with the control panel and remote
control and all its functions (as shown below). The unit can be controlled by the
touch pad alone, with the remote control, or with the Frigidaire app*.
DISPLAYS
TEMPERATURE
ADJUSTS
TEMPERATURE
SETS FAN
SPEED
TAB
&+(&.),/7(5
RESET BUTTON
WIFI
WARNING: Chemical Burn Hazard.
Keep batteries away from children.
This product contains a lithium button/coin cell
battery. If a new or used lithium button/coin
cell battery is swallowed or enters the body, it
can cause severe internal burns and can lead
to death in as little as 2 hours. Always
completely secure the battery compartment.
If the battery compartment does not close
securely, stop using the product, remove the
batteries, and keep it away fr
you think batteries might have been swallowed
or placed inside any part of the body, seek
immediate medical attention.
The cells shall be disposed of properly,
including keeping them away from children;
Even used cells may cause injury.
SCHEDULE
INDICATOR
om childre
n. If
Operating Instructions
NOTE
The following instructions represent the touch pad. The same instructions can be used for the remote control.
YOU WILL SEE:TO TURN UNIT ON:
DO THIS:
PRESS ON/OFF BUTTON
NOTE: The unit will run in energy saver(econ) mode
when powered on each time, if last shutdown is in cool
or energy saver(econ) mode.
The fan then cycles on for 120 seconds at 10 minute intervals
until the room temperature is above the set temperature, at
which time the compressor turns back on.
In this mode, the fan will
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
7
Operating Instructions
Operating Instructions
(continued)
TO CHANGE TEMPERATURE SETTlNG:
DO THIS:
S
PRES TO RAISE
S
PRES TO LOWER
YOU WILL SEE:
Note: The display will show the set temperature during
normal operation, press either up ( + ) or down ( – )
button to adjust the set temperature to the desired
setting. The unit will beep twice if the temperature up ( + )
or down ( – ) button is pressed continuously when the set
temperature reaches the upper/lower limits 90°F or 60°F.
YOU WILL SEE:TO ADJUST FAN SPEEDS:
DO THIS:
PRESS TO SELECT
DO THIS:
PRESS FAN BUTTON,
CHOOSE AUTO
YOU WILL SEE:TO USE AUTO FAN FEATURE:
Note: Fan starts at High Speed and adjusts to a slower
speeds the room temperature dictates. For example, if the
room doesn't get too warm, it will stay at the slowest speed.
If the room temperature rises quickly, such as a door being
opened, it will automatically go to the highest speed. The fan
speeds will re-adjust back to the slowest speed as the room
returns to the original set temperature. Press either the fan
slower or fan faster button to adjust the fan speed manually.
8
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Operating Instructions
(continued)
Operating Instructions
:EES LLIW UOY:NAF NO ETAREPO OT
DO THIS:
PRESS
MODE BUTTON
CHOOSE FAN
COOL FEATURE:
DO THIS:
PRESS
MODE BUTTON
CHOOSE COOL
ECO (ENERGY SAVER) MODE:
Note: Use this function only when cooling is not desired,
such as for room air circulation or to exhaust stale air on
some models. You can choose any fan speed you
prefer. (Except “Auto Fan”).
During this function, display will only show the actual
room temperature and the set temperature can not be
changed.
YOU WILL SEE:
Note: In this mode, the fan remains on all the time with the
compressor cycling on and off when room temperature is
reached.
The unit is factory set to run in eco (energy saver) mode.
DO THIS:
PRESS
MODE BUTTON
CHOOSE COOL
We recommend leaving the unit in eco mode to help save
energy and money. However, if you would like to switch
out of eco mode, touch the button until another mode
is selected.
In eco mode, the fan will continue to run for 3 minute after
the compressor shuts off. The fan then cycles on for 120
seconds at 10 minute intervals until the room temperature
is above the set temperature, at which time the compressor
turns back on.
NOTE:
Please note, that if the unit is changed to 'cool' or 'fan' mode then shut off, the unit will turn back on in eco mode. This is
mandatory per government regulations. If the unit is changed to 'cool' or 'fan' mode and a power failure occurs, once the
power is restored the unit will return to 'cool' or 'fan' mode.
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
9
Operating Instructions
Operating Instructions
(continued)
TO OPERATE SWING FEATURE:
DO THIS:
PRESS SWING
BUTTON
TO ACTIVATE THE CHILD LOCK FEATURE:
YOU WILL SEE:
Note: In this feature the louver will swing up and down
to distribute the air evenly.
YOU WILL SEE:
DO THIS:
PRESS AND HOLD THE
“Fan Speed” & “Filter Reset” BUTTONS
SIMULTANEOUSLY FOR 3 SECONDS
CHECK FILTER FEATURE, YOU WILL SEE:
Note: This feature is a reminder to clean the Air Filter (See
Care and Cleaning) for more efficient operation. The LED
(light) will illuminate after 250 hours of operation. To reset
after cleaning the filter, hold the " reset filter" button 3
seconds and the light will go off.
Note: Press and hold the “ Fan Speed ” and “ Filter Reset ”
EXWWRQIRUVHFFDQDFWLYDWHRUGHDFWYDWHWKH/2&.IXQFWLRQ
The display will show LC for 5 secs. The control panel will
be lock and the setting can not be changed.
DO THIS:
HOLD RESET FILTER
BUTTON 3 SECONDS
10
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Operating Instructions
Operating Instructions
(continued)
FAULT CODES:
When below error code show on the display, please contact your Authorized Frigidaire Service Center.
Error Code Description
EH03
EC51
EC52
EC53
EC54
EH60
EH61
EC07
EH0b
EL0C
PC00
PC01
PC02
PC04
PC0L
Internal motor(fan motor) loss speed
Outdoor unit EEPROM malfunction
Outdoor condenser temperature sensor is open/short circuited
Outdoor ambient temperature sensor is open/short circuited
Outdoor discharge temperature sensor is open/short circuited
Indoor ambient temperature sensor is open/short circuited
Indoor evaporator temperature sensor is open/short circuited
Internal motor(fan motor) loss speed/outdoor motor loss speed/Compressor starting anomaly/outdoor
unit was stolen
Communication malfunction
Refrigerant detection failure
Outdoor IPM unit protection
Outdoor voltage protection
Compressor top temperature Protection (IPM) module temperature protection
Outdoor compressor feedback protection
Outdoor cryogenic protection
Note: The error code will be seperated to 2 part and shown in the display alternately in 1 second intervals, for example, when
the fault code “EH03” occur, the panel will first display “EH” for 1 sec, then display “03” for another sec and keep repeatedly
showing “EH” and “03” until the issue are solved.
SHOW “EH” FOR ONE SECONDS: THEN SHOW “03” FOR ANOTHER SECONDS:
TO CHANGE TEMPERATURE DISPLAY:
DO THIS:
PRESS AND HOLD THE
UP/DOWN BUTTONS
SIMULTANEOUSLY FOR 3 SECONDS
YOU WILL SEE:
Note: The control is capable of displaying temperature in
degrees Fahrenheit or degrees Celsius.
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
11
Operating Instructions
Operating Instructions
(continued)
DIMMING DISPLAY:
After 60 seconds of control inactivity the display and indicator lights will turn off. Press any button on the control panel or remote
control and the display will resume. Please note that if the unit is in eco mode and the set temperature has been reached the unit
may appear off. However, the unit is on and will continue to sample the air every 10 minutes. To confirm, press any button on the
control panel or remote control to illuminate the display to show unit in eco mode.
TO TURN UNIT OFF:
DO THIS:
PRESS
ON/OFF BUTTON
YOU WILL SEE:
Note: After the unit is turned off, the light on the display
will gradually fade away in 3 seconds. The unit will always
return to “eco” mode and “auto” fan speed setting when it
is turned on again.
ADDITIONAL THINGS YOU SHOULD KNOW
Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.
The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly.
This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue
to run during this time.
There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY. This is to cover the possibility of having
to roll through to select another mode.
The control will maintain the set temperature within 2 degrees Fahrenheit, between 60°F and 90°F degrees.
After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.
12
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Care and Cleaning & Energy Saving Ideas
Care and Cleaning
Tab
Air Filter
Clean your air conditioner occasionally to keep it looking new. Be sure to unplug
the unit before cleaning to prevent shock or fire hazards.
Air Filter Cleaning
The air filter should be checked at least once a month to see if cleaning is
necessary. Trapped particles in the filter can build up and cause an accumulation
of frost on the cooling coils.
Push the vent handle to the Vent Closed position(where applicable).
Open the front panel.
Grasp the filter by the center and pull up and out.
Wash the filter using liquid dishwashing detergent and warm water. Rinse filter
thoroughly. Gently shake excess water from the filter. Be sure filter is
thoroughly dry before replacing
Or instead of washing, you may vacuum the filter clean.
NOTE: When replacing the air filter after cleaning, make sure the tabs on the air
filter are on the upper part of filter, and placed outward as shown in the drawing
on the left side.
Cabinet Cleaning
Be sure to unplug the air conditioner to prevent shock or fire hazard. The
cabinet and front may be dusted with an oil-free cloth or washed with a cloth
dampened in a solution of warm water and mild liquid dishwashing detergent.
Rinse thoroughly and wipe dry.
Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping around the controls.
Excess water in or around the controls may cause damage to the air conditioner.
Plug in air conditioner.
Winter Storage
If you plan to store the air conditioner during the winter, remove it carefully from
the window according to the installation instructions. Cover it with plastic or return
it to the original carton.
Energy Saving Ideas
Do not block air flow inside with blinds, curtains or furniture; or outside with
shrubs, enclosures, or other buildings.
The capacity of the room air conditioner must fit the room size for efficient and
satisfactory operation.
Install the room air conditioner on the shady side of your home. A window that faces
north is best because it is shaded most of the day.
Close the fireplace damper, floor and wall registers so cool air does not escape up
the chimney and into the duct work.
.eep blinds and drapes in other windows closed during the sunniest part of the day.
Clean the air filter as recommended in the section “Care and Cleaning”.
Proper insulation and weather stripping in your home will help keep warm air out
and cool air in.
External house shading with trees, plants or awnings will help reduce the air
conditioner’s work load.
Operate heat producing appliances such as ranges, washers, dryers and dishwashers
during the coolest part of the day.
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
13
Before You Call
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not
the result of defective workmanship or materials in this appliance.
OCCURRENCE SOLUTION
Air conditioner will not operate.
Air from unit does not feel cold
enough.
Air conditioner cooling, but room
is too warm - ice forming
on cooling coil behind decorative
front
Air conditioner cooling, but room
is too warm - NO ice forming on
cooling coil behind decorative
front.
Wall plug disconnected. Push plug firmly into wall outlet.
Plug Current Device Tripped. Press the RESET button.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.
Control is OFF. Turn Control ON and set to desired setting.
Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above
60°F (16°C).
Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.
Reset to a lower temperature.
Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to
restart when set in the COOL mode.
Outdoor temperature below 60 F (16 C). To defrost the coil, set FAN ONLY mode.
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY
mode.
Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then,
set temperature to a higher setting.
Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.
Temperature is set too high. Set temperature to a lower setting.
Air directional louvers positioned improperly. Position louvers for better air distribution.
Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in
front of unit.
Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.
Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling,
floor and furniture.
OO
Air conditioner turns on and off
rapidly.
Noise when unit is cooling.
Water dripping INSIDE when
unit is cooling.
Water dripping OUTSIDE when
unit is cooling.
Remote Sensing Deactivating
Prematurely (some models).
Room too cold.
Trouble connecting the smart
appliance to your wifi network or
experiencing an issue with the app.
Dirty air filter - air restricted. Clean air filter.
Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils
more frequently.
Air movement sound. This is normal. If too loud, set to lower FAN setting.
Window vibration - poor installation. Refer to installation instructions or check with installer.
Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to
installation instructions or check with installer.
Unit removing large quantity of moisture from humid room. This is normal during excessively humid
days.
Remote control not located within range. Place remote control within 20 feet & 120° radius of the
front of the unit.
Remote control signal obstructed. Remove obstruction.
Set temperature too low. lncrease set temperature.
Remote Sensing activated (on some models) and remote control located in Hot Spot - Relocate remote
control or deactivate remote sensing.
Please visit Frigidaire.com and select the Owner Support section to view Frequently Asked Questions.
If These Solutions Fail, Call 1-800-944-9044(US)/1-800-265-8352(Canada)
For Frigidaire Service.
14
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Major Appliance Limited Warranty
Your appliance is covered by a limited one-year warranty for functional repairs only. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials
or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. After one
year from your original date of purchase, the consumer will be responsible for diagnostic, labor and parts costs as well as any
removal, transportation and reinstallation expenses which are incurred during service on components.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,
handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external
causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST
PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME
STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Service
This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described
or illustrated are subject to change without notice.
USA
1.800.944.9044
Electrolux Major Appliances
10200 David Taylor Drive
Charlotte, NC 28262
.HHS\RXUUHFHLSWGHOLYHU\VOLSRUVRPHRWKHUDSSURSULDWHSD\PHQWUHFRUGWRHVWDEOLVKWKHZDUUDQW\SHULRG
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
15
Loading...