1
WINE CELLAR
INSTRUCTION MANUAL
酒櫃
操作指引
Thanks for buying Frigidaire wine cellar, Hope our quality product will give your wine
a different joyful taste.
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND
OPERATING INSTRUCTIONS.
感謝您購買北極牌酒櫃，希望我們優產的產品會令您安心享用珍愛的葡萄酒。
使用前，請閱讀並遵守所有安全規則和操作指引。
2
IMPORTANT SAFETY INSTRUCTIONS
• To reduce the risk of fire, electrical shock, or injury when using your appliance, follow
these basic precautions:
• Read all instructions before using the Wine Cellar.
• Before you throw away your old Wine Cellar: Take off the door and remove the
shelves in place so that children may not easily climb inside.
• Never allow children to operate, play with, or crawl inside the appliance.
• Never clean appliance parts with flammable fluids. The fumes can create a fire hazard
or explosion.
• Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of
this or any other appliance. The fumes can create a fire hazard or explosion.
• Keep these instructions for reference
INSTALLATION INSTRUCTIONS
Before Using Your Wine Cellar
• Remove the exterior and interior packing.
• Before connecting the Wine Cellar to the power source, let it stand upright for approximately 2
hours. This will reduce the possibility of a malfunction in the cooling system from handling
during transportation.
• Clean the interior surface with lukewarm water and soft cloth.
• Install the handle on the side of the door according user’s desire.
• When replace the illuminating lamp, please select the lamp which is complied with the rated
power input of lamp according to the rating label. Shut off the power supply before replacing
the lamp.
• When disposing your appliance, please choose an authorized disposal site.
Installation of Your Wine Cellar
• Place your Wine Cellar on a floor that is strong enough to support it when it is fully loaded. To
level your Wine Cellar, adjust the front leveling leg at the bottom of the Wine Cellar.
• Locate the Wine Cellar away from direct sunlight and sources of heat (stove, heater, radiator,
etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical
consumption. Extreme cold ambient temperatures may also cause the unit not to perform
properly.
• Avoid locating the unit in moist areas.
• Plug the W ine Cellar into an exclusive, properly installed-grounded wall outlet. Do not under
any circumstances cut or remove the power cord. Any questions concerning power and/or
grounding should be directed toward a certified electrician or an authorized product service
center.
3
Chapter 1: ATTENTION
To prevent the door gasket damage, make sure to have the door all the way opened when pulling
shelves out of the rail compartment.
The appliance must be positioned with the plug accessible area. Release the power cord and move
your cabinet to its final location. Do not move your cellar while loaded with wine. You might distort
the body and inappropriate impact. The wine cooler should be installed in a suitable place in order
to avoid touching the compressor by hand.
If the door hinge need to adjust for your desire direction, please directed toward a certified
electrician or an authorized product service center in avoid inappropriate impact on operation.
If the supply cord is damaged, it must be replaced by certified electrician or an authorized product
service center.
Attention
• Store wine in sealed bottles;
• Do not overload the cellar;
• Do not open the door unless necessary in avoid temperature fluctuation;
• Do not cover shelves with aluminum foil or any other shelf material which may prevent air
circulation;
•
Should the Wine cellar be stored without use for long periods it is suggested, after a careful
cleaning, leave the door ajar to allow air to circulate inside the cellar. This will avoid possible
formations of condensation, mold or odors.
Chapter 2 : HOW TO INSTALL AND REMOVE THE SHELF
FWC18B
• For easy access to the storage content, you must pull the shelves approximately 1/3 out of the rail
compartment, however this unit was designed with a notch on each sides of the shelf tracks to
prevent bottles from falling.
• When removing any of these shelves out of the rail compartment, to fit or remove the shelf, tilt the
shelf as per the diagram and simply pull out, or push in the shelf until it sits on the support
brackets securely.
FWC33B FWC46BD FWC50B FWC110B FWC110BD FWC168B FWC154BD
• For easy access to the storage content, you must pull the shelf approximately 1/2 out of the rail
compartment, however this unit was designed with a post on each sides of the shelf track to
prevent bottles from falling.
• When removing the shelf out of the inner rail, make sure to remove all items first. Then move the
shelf to the position where the notch of shelf is exactly under the post and lift the shelf. In order to
replace the shelf, repeat steps described above in reverse.
4
Chapter 3 : OPERATING YOUR WINE CELLAR
The Wine Cellar should be placed in where the ambient temperature is between 5-35℃. If the
ambient temperature is above or below this range, the performance of the unit may be affected. For
example, placing your unit in extreme cold or hot conditions may cause interior temperatures to
fluctuate. The range of 5-18℃ (40-65ºF) may not be reached.
FWC18B
Control System Instruction
Temperature
• “RUN” Button
Indicator light illuminates to signify the cooling mode is currently in operation.
• “ ”Button
To control the inner light turn on/off.
• “POWER” Button
To control this appliance turn on/off ( press and hold this buttons for approximately
3 seconds).
• “ ” Button
Used to raise(warm) the temperature in 1 .℃
• “ ” Button
Used to lower(cool) the temperature in 1 . ℃
Shelves
• To prevent damaging the door gasket, make sure to have the door all the way opened when
pulling shelves out of the rail compartment.
NOTE:
• If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes before restarting
the unit. If you attempt to restart before this time delay, the Wine cellar will not start and cause
inappropriate impact.
•
When you use the Wine cellar for the first time or restart the Wine cellar which is without use for a
long time, there could be a few degrees variance between the temperature you select and the one
indicated on the LED readout. This is normal and it takes time to recover. The Wine cellar will go
back to normal after several hours running.
5
FWC33B FWC50B FWC110B FWC168B
Recommended Temperatures for Chilling Wine as below, details information please consult with your
wine consultant.
Red Wines: 15 -18 (℃58 – 65 °F)
Dry/White Wines 9 -14 (℃48 – 57 °F)
Sparkling Wines 5 – 8 (℃40 - 47 °F)
The above temperatures may fluctuate depending on the interior bulb is ON or OFF or whether the
bottles are located on the upper or lower section.
To turn ON/OFF the appliance(press and hold the button for approximately 2 seconds).
Setting the Temperature Control
• You can set the temperature as you desire by pushing the UP(+) or DOWN(-) button. When you
push the two buttons for the first time, the LED readout will show the original temperature set at
previous time (the temperature preset at the factory is 12℃(54ºF).
• The temperature that you desire to set will increase 1ºF or 1ºC if you push the UP(+) button once,
on the contrary the temperature will decrease 1ºF or 1ºC if you push the DOWN(-) button once.
• When you store mostly red wines, the temperature which you control by pushing the above two
buttons need to be set at between 15-18℃ (58 to 65°F).
• When you store mostly white wines, the temperature needs to be set at between 9-14℃(48 to 57
°F).
• When you store mostly sparkling wines, the temperature needs to be set at between 5-8℃(40 to
47 °F).
• You can select temperature display setting from Fahrenheit to Celsius degree by pushing the
UP(+) and DOWN(-) button at the same time for 5 seconds. Fahrenheit and Celsius degrees
indicator will appear in green color in the “SET” window. (Due to different market, some units can
only display Fahrenheit or Celsius)
• The temperature inside the unit will be appear in blue color in the “TEMPERATURE” window.
FWC46BD FWC110BD FWC154BD
The above temperatures may fluctuate depending on whether or not the interior bulb is ON or OFF or
whether the bottles are located on the upper/middle or lower section.
To turn ON/OFF the appliance(press and hold the button for approximately 2 seconds).
Setting the Temperature Control
• Each cooling compartment of the wine cooler (upper & lower) is independently controlled. To set
6
the temperature:
Connect the power cord to a properly grounded outlet. In the event of a power interruption, all
previous temperature settings are automatically erased and each compartment will default to a
preset temperature setting of: 6℃ (43℉) for upper compartment and 12℃(54℉) for lower
compartment.
Set the desired cooling temperature by pressing the buttons adjacent to the “set upper/set lower”
program. Each depression of the buttons will scroll through the available temperature settings
(for each compartment) in decreases of 1 degree. The temperature selected will flash in the LED
display for approximately 5 seconds, then revert back to display the temperature of the internal
cabinet
Upper compartment: The temperature setting can be adjusted from 5℃ to 12℃ (40℉ to 54℉).
Lower compartment: The temperature setting can be adjusted from 12℃ to 18℃ (54℉ to 65℉).
To view the “set” temperature. (anytime) press and hold the corresponding button for
approximately 5 seconds, the “set” temperature will temporarily “flash” in the LED display for 5
seconds.
• This unit has the option to display temperatures in either Celsius or Fahrenheit. To change the
setting, press and hold both buttons (Set Upper/Set Lower) simultaneously for approximately 5
seconds, a prompt (beep) will sound and the blue pilot light adjacent to the C or F mode
illuminates. (Due to different market, some units can only display Fahrenheit or Celsius)
NOTE:
• If the unit is unplugged, power lost, or turned off; you must wait 3 to 5 minutes before restarting the
unit. If you attempt to restart before this time delay, the Wine Cellar will not start and cause
inappropriate impact.
• When you use the Wine cellar for the first time or restart the Wine cellar which is without use for a
long time, there could be a few degrees variance between the temperature you select and the one
indicated on the LED readout. This is normal and it takes time to recover. The Wine cellar will go
back to normal after several hours running.
•
Interior Light
You can turn the interior light ON or OFF by pushing the button marked with the “light” symbol .
Door Lock
Your unit is provided with a lock and key combination.
The keys are located inside the plastic bag that contains the User’s Guide. Insert the key into the
lock and turn it counterclockwise to unlock the door. To lock the door do the reverse operation
making sure metal pin is engaged completely. Remove the key and place it in a secure place for
safekeeping.
Chapter 4 : CARE AND MAINTENANCE
Replacing LED Light
You must cut off electrical power avoid tip-and-run hurt.
Please remove 2 fixed screws of the top shelf by Philips screwdriver and take out the shelf.
(Attention please: LED light is covered by electrical box.)
Please take out lock screw by Philips screwdriver first, then push the light cover to left, you
can take out it when light cover set out limited location. (Fig.A)
Please pull out Housing 4 from 6 of LED light board. (Fig. B)
Please take out 2pcs of screw 5 by Philips screwdriver. (Fig.C)
Please pull out LED light board 6 from light cover. (Fig.D)
Please replace new LED light according above method.
7
1. Inner liner 3. Lamp cover 5. Screws
2. Lock screws 4. Housing 6. LED light
Cleaning Your Wine Cellar
• Turn off the power, unplug the appliance, and remove all items including shelves and rack.
• Wash the inside surfaces with a warm water and baking soda solution. The solution should be
about 2 tablespoons of baking soda to a 1/4 Litre of water.
• Wash the shelves with a mild detergent solution.
• Wring out excess water out of the sponge or cloth when cleaning area of the controls, or any
electrical parts.
• Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry
with a clean soft cloth.
Power Failure
• Most power failures are corrected within a few hours and should not affect the temperature of
your appliance if you minimize the number of times the door is opened. If the power is going
to be off for a longer period of time, you need to take the proper steps to protect your contents.
Vacation Time
• Short vacations: Leave the Wine Cellar operating during vacations of less than three weeks.
• Long vacations: If the appliance will not be used for several months, remove all items and
turn off the appliance. Clean and dry the interior thoroughly. To prevent odor and mold
growth, leave the door open slightly: blocking it open if necessary.
Moving Your Wine Cellar
• Remove all items.
• Securely tape down all loose items (shelves) inside your appliance.
• Turn the adjustable leg up to the base to avoid damage.
• Tape the door shut.
• Be sure the appliance stays secure in the upright position during transportation. Also protect
outside of appliance with a blanket, or similar item.
Energy Saving Tips
• The Wine Cellar should be located in the coolest area of the room, away from heat producing
appliances, and out of the direct sunlight.
8
Chapter 5
QUESTIONS & ANSWER
You can solve many common Wine Cellar problems easily, saving you the cost of a possible service
call. Try the suggestions below to see if you can solve the problem before calling the service.
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
Wine Cellar does not operate.
Not plugged in.
The appliance is turned off.
The circuit breaker tripped or a blown fuse.
Wine Cellar is not cold enough. Check the temperature control setting.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
Wine Cellar Cooling Fan Turns on and off
frequently.
The room temperature is hotter than normal.
A large amount of contents has been added to
the wine Cellar and stuck the air circulation.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not work.
Not plugged in.
The circuit breaker tripped or a blown fuse.
The bulb has burned out.
The light button is “OFF”.
Vibrations. Check to assure that the Wine Cellar is level.
The Wine Cellar seems to make too much noise.
The rattling noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling
sounds caused by the flow of refrigerant in your
Wine Cellar.
Contraction and expansion of the inside walls
may cause popping and crackling noises.
The Wine Cellar is not level.
The door will not close properly.
The Wine Cellar is not level.
The door was reversed and not properly installed.
The gasket is dirty.
The shelves are out of position.
9
安全
安全安全
安全提提提提示示示示
•
為了使用時減低火災，電擊，或受傷的風險，請遵從下列基本預防措施：
•
在使用酒櫃前閱讀所有操作指引說明。
•
在你扔掉舊的酒櫃
在你扔掉舊的酒櫃在你扔掉舊的酒櫃
在你扔掉舊的酒櫃前前前前::::
拆掉櫃門並移開層架以防止孩子入內。
•
切勿讓兒童操作及接近，或爬入機器內
。
•
切勿使用易燃液體清潔家用電器配件。這種氣體可以引致火災或爆炸。
•
在機器附近，不要儲存或使用汽油或其他易燃氣體和液體。這種氣體可以引致火災或爆炸。
•
請保存此操作指引以備日後使用
安裝指引
安裝指引安裝指引
安裝指引
使用酒
使用酒使用酒
使用酒櫃櫃櫃櫃前前前前
•
拆除櫃內外包裝。
•
在酒櫃連接到電源前或移動後，讓它直立大約 2 小時。這將減少冷卻系統發生故障的可能性。
•
用溫水軟布清潔機內表面。
•
在櫃門安裝手柄. 使用者可根據需要安裝櫃門把手
•
當更換照明燈，請按照標籤選擇符合電力輸入功率的燈泡。更換燈泡前要切斷電源供應。
•
當您棄置電器，請選擇合法棄置場所。
安裝酒
安裝酒安裝酒
安裝酒櫃櫃櫃櫃
•
請將您的酒櫃放在一個足夠承托滿載酒櫃的樓層結構上。並在使用前調整酒櫃底部機腳以平衡
您的酒櫃。
•
把酒櫃放到遠離直接陽光的照射和熱源（爐，加熱器，散熱器等）。陽光直射可能會影響塗料
及機內温度，熱源可能會增加耗電量及對存酒造成影響。極端寒冷的環境溫度也可能會導致機
器不正確運作。
•
避免在潮濕的地區及缺乏通風的位置裝置機器。
•
正確安裝接地插座並連接酒櫃電源。在任何情況下，不要剪掉或移除電線。任何有關電力連接
及操作，應該交由合資格的電工或代理商產品
服務中心處
理。
10
第一章
第一章第一章
第一章 :
: :
: 注意事項
注意事項注意事項
注意事項
為了防止弄損櫃門的墊圈及門封，當櫃內層架由
路軌分隔撤出前,
請確保機門
已完全打
開。
酒櫃應設置在容易連接電源插座的地方，鬆解電線後並將您的酒櫃移到最終位置。不要移動裝載
了酒的酒櫃，這可能會拉傷你的身體並造成不當的影響。酒櫃應安裝在合適及安全的地方，以防
止接
觸壓縮
器。
如需更改開門方向
，請交由製造商，代理或合資格
人士處
理更換，以免不當處理影響操作效果。
如果
電源線損壞，必須由製造商，代理或合資格
人士處
理更換，以避免造成危險。
注意
注意注意
注意
•
存儲密封的葡萄酒瓶。
•
酒櫃不要過載。
•
如非必
要，不要打開門以免温度過度變化。
•
不要以
鋁箔覆蓋
層架或其他任何層架的材料，可能會
妨礙空氣流
通。
•
如果長時間
不使用，
我們建議仔細清洗機內各部份
後，把機門半掩讓空氣在酒櫃流通，以避免
可能出現的發霉和
臭味形
成。
第二章
第二章第二章
第二章 :
: :
:
如何
如何如何
如何
安裝及
安裝及安裝及
安裝及
移移移移除除除除層層層層架架架架
FW
FWFW
FWC18B
C18BC18B
C18B
•
為了
方便取出
存儲的物件，
你必須由路軌分隔拉出
層架大約1 / 3，層架的
兩旁軌道
備有安全鎖部件
以防止層架及酒
瓶跌出
。
•
在支撐托座上安裝或移除任何層架，傾斜層架如圖並簡單地拉出，或推入層架後直到
坐穩於支撐
托
座上才放下。
FWC33B
FWC33B FWC33B
FWC33B FWC46BD
FWC46BDFWC46BD
FWC46BD FWC50B
FWC50BFWC50B
FWC50B
FWC110B
FWC110BFWC110B
FWC110B
FWC110BD FWC168B FWC154BD
FWC110BD FWC168B FWC154BDFWC110BD FWC168B FWC154BD
FWC110BD FWC168B FWC154BD
•
您必須把層架
拉出軌道
的大約1 / 2 以
便提取酒瓶，而
層架的
兩旁軌道
備有安全鎖部件以防止層架及
酒
瓶跌出
。
•
移除層架前，請確保所有物件已移除。然後才移動層架的位置，讓層架的切口對正安全鎖部件
之
下，然後提起層架。要更換層架，
相反重複上述步驟。
11
第三章
第三章第三章
第三章 :
: :
: 酒櫃的操作及設定溫度控制
酒櫃的操作及設定溫度控制酒櫃的操作及設定溫度控制
酒櫃的操作及設定溫度控制
酒櫃應放置在周圍環境溫度
5-35℃之間。如果
環境溫度高於或低於此範圍內，酒櫃的操作溫度會受到
波
動,而櫃內温度不能達致標準的
5-18℃(40-65
°F)
。
FWC18B
FWC18BFWC18B
FWC18B
控制系統指令
控制系統指令控制系統指令
控制系統指令
Temperature
•
““““運作
運作運作
運作”
” ”
” 按鈕
按鈕按鈕
按鈕
指示燈點著，以顯示冷卻
模式目
前正在運作中。
• “ ”
按鈕
按鈕按鈕
按鈕
控制
內部照明燈開啟/關閉。
•
““““開關
開關開關
開關”
” ”
” 按鈕
按鈕按鈕
按鈕
控制
酒櫃開/閉（按下此按鈕大約
3 秒
）。
• “ ”
按鈕
按鈕按鈕
按鈕
•
用
於提升 1℃
溫度。
• “ ”
按鈕
按鈕按鈕
按鈕
用於降低1℃溫度。
層架
層架層架
層架
•
為了防止弄損櫃門的墊圈及門封，當櫃內層架由
路軌分隔撤出
前， 請確保機門
已完全打
開。
注意
注意注意
注意
::::
•
如
酒櫃電源被拔掉，停電，或已關閉，您必須等
待 3 至 5 分鐘才可重新啟
動酒櫃。如果您嘗試在此
時間之前
重新啟
動，酒櫃將無法啟動並對其造成損害。
•
當您首次使用酒櫃或
重新啟動已關閉很長一段時間
的酒櫃時，您選擇的溫度和
LED 顯示讀數之間
可
能會出現一些溫度上的差異。這是正常的，這是由於酒櫃內的温度需要調整。當酒櫃運行幾個小時
後一切將恢復正
常
。
FWC33B
FWC33B FWC33B
FWC33B FWC50B
FWC50BFWC50B
FWC50B
FWC110B
FWC110BFWC110B
FWC110B
FWC168B
FWC168BFWC168B
FWC168B
建議
保存溫度如下，詳細資料請諮詢您的顧問。
紅葡萄酒:
15 -18℃ (58 - 65°F)
乾/白葡萄
酒 9
-14℃ (48 - 57°F)
氣葡萄酒
5-8℃ (40 - 47°F)
以上的溫度可能視乎內部燈泡是否開動或關閉，
而且瓶子置於
上部或下部亦有不同。
12
要開/關電器（按住按鈕約 2秒）。
•
溫度設置控制
•
您可以使用上（+）或下（ - ）按鈕調校理想溫度。當
你首次
按下這兩個調校按鈕，
LED 顯示原
本
溫度設定（在工廠預設的溫度
是華氏 12℃(54ºF)
。
•
你
按上（+）按鈕一次, 你的理想溫度將會增加1 º F或1℃，
相反你
按下（ - ）按鈕，氣溫將下
降 1 º
F或1℃
。
•
當您儲存大
多是紅葡萄
酒，需要設定在
15-18℃（58 至 65°F）。
•
當您儲存大
多是白葡萄
酒，溫度
必須設定在9-14℃ (48 至 57°F)
.
•
當您儲存大多是氣葡萄酒，溫度需要設置
之間 5-8℃ (40 至 47°F)
.
•
您可以選擇
顯示設
置溫度從
華氏改至攝氏, 只需在同一時間按下向上（+）和向
下（ - ）按
鈕 5 秒
。
華氏攝氏度的顯示將以藍色字出現在LED 顯示。
•
在機器內的溫度將以
藍色字體出現在“温度”窗口。
FWC46BD FWC110BD FWC154BD
FWC46BD FWC110BD FWC154BD FWC46BD FWC110BD FWC154BD
FWC46BD FWC110BD FWC154BD
以上的溫度可能視乎內部燈泡是否開動或關閉，
而且瓶子置於
上部或下部亦有不同。
要開/關電器（按住按鈕約 2秒）。
設定溫度控制
設定溫度控制設定溫度控制
設定溫度控制
酒櫃內的存酒層區（上，下）是獨立控制。需要
設定各自
溫度：
連接電源線到電源插座。當停電事故發生, 所有以前的溫度
設定自動刪除，每
個層區將會自動
回復
為預設的溫度設定在：上層層區6℃（
43℉
），和下層層區12℃（
54℉
）。
按下“上/下層區設置
”LED 顯示旁邊的按鈕來設定
所需的溫度。每按一下按鈕, 現有的溫度會
（所選層區）下
降 1
度。設定溫度會在
LED 顯示屏閃
動約
5 秒鐘，然後恢復到顯示
內部酒櫃的溫度
上層: 溫度設定可以調
節 5℃ 至 12℃ (40℉至 54℉)
.
下層
::::
溫度設定可以調
節 12℃至 18℃ (54℉至 65℉)
.
要
查看“設置”
溫度。（隨時）按住相應按鈕約
5 秒鐘，“設
置，溫度將暫時在
LED 顯示屏“閃
動” 5 秒。
•
選擇
顯示攝氏或華氏
溫度或更改原有設置，可同時按住兩個按鈕（設置上層/下層區）約
5 秒鐘
，
LED 顯示屏的C或F 模式會進行
更動。 （由於不同的市場，一些電器只能
顯示華氏或攝氏）
注意
注意注意
注意::::
•
如果機器被拔掉插頭，沒
有電源，或者關閉，
重新啟
動機器前
你必須等待 3到5 分鐘，。如果您嘗
試在延遲時間之前重新啟
動，酒櫃將無法啟動並對其造成損害。
•
當您使用酒櫃首次或
重新啟動已關閉很長一段時間
的酒櫃，您選擇的溫度和
LED 顯示讀數之間
可能
會出現一些溫度上的差異。 這是正常的，這是由於酒櫃內的温度需要調整。當酒櫃運行幾個小時後
一切將恢復正
常
。
室內燈
室內燈室內燈
室內燈
您還可以按動標記“燈光”符號 的按鈕來開或關室內燈.
門鎖
門鎖門鎖
門鎖
您的機器提供了鎖和
鑰匙組
合
。
鑰匙位於包含
操作指引的塑料袋內。將鑰匙插入鎖並逆時
針轉來打
開門。相反的操作把門鎖上，確
13
保
金屬針是完全
插入。
提出鑰匙
，並把它放在安全的地方保管。
第四章
第四章第四章
第四章 :
: :
: 護理和保養
護理和保養護理和保養
護理和保養
更換
LED
燈
你必須
切斷電源，避免因電源導致不必要的傷害。
請使用十字
螺絲批移除頂
端層架的 2
枚固定螺絲，並取出
了層架。 (請注意：電氣盒覆蓋 LED燈.)
請首先使用十字螺絲批起子
取出鎖定螺絲，然後輕推燈蓋至左面, 當燈罩設到有限
的位置, 你便可以
把它取出。（圖A
）
請將
LED
燈從安放位拉出. (圖B)
請使用十字
螺絲批拿出2
顆螺絲5。 (圖.C)
請由燈罩將
LED燈拉出並進行
更換。 (圖.D)
請根據以上方法更換新的
LED
燈。
1. 內線 2. 鎖定螺絲 3. 燈罩 4. 安放位 5. 螺絲 6. LED 燈
清潔
清潔清潔
清潔您的酒櫃
您的酒櫃您的酒櫃
您的酒櫃
•
關閉電源，拔掉電器，並移除所有物品，包括存酒和層架。
•
用溫水和蘇打
開水清洗機內表面。混合劑應該是約 2湯匙的蘇打對
1/4公升
的水。
•
用溫和的洗滌劑清洗
層架。
•
當清
洗控制
器或任何零件時，海綿或布要扭出多餘的水分。
•
用溫水和溫和的液體洗滌劑清洗
酒櫃外面。並用洗淨和乾淨的軟布抹乾
。
停電
停電停電
停電
•
大部分停電要幾個小時才能恢愎，如果你
減少開門
次數
，可減少對酒櫃溫度影響。
如果長時期
停
電，您需要採取適當的步驟來保護
您的酒。
休假時間
休假時間休假時間
休假時間
•
短期休假
::::
離開酒櫃不超過三個星期可保持使用。
•
長假期：
如果該設備將於幾個月
不會使用，移除所有物品，並關掉機器。
•
徹
底清潔及抹乾
櫃內。為了防止氣味和黴菌生長，
稍微敞
開大門吹乾或完全封閉
機門。
移動您的酒櫃
移動您的酒櫃移動您的酒櫃
移動您的酒櫃
•
移除所有物品.
•
在酒櫃內固定所有鬆散物
件（酒架）。
•
轉
動櫃底調節腳以避免損壞。
•
緊貼
櫃門並確保不會開啓。
•
在運輸過程中，要確保電器安全保持直立。還以一張毯子或類似的物品保護酒櫃外面。
節能小貼士
節能小貼士節能小貼士
節能小貼士
14
•
酒櫃應放於房間最冷凍的地方，遠離發熱機器，並避免陽光直接照射。
第五章
第五章第五章
第五章
問題及解答
您可以很容易解決許多酒櫃常見的問題, 節
省維修服務的成本。請嘗試下列建議，
看看是否
能在致電
維
修服務前解決問題。
排解疑難指引
排解疑難指引排解疑難指引
排解疑難指引
問題
問題問題
問題 問題成因
問題成因問題成因
問題成因
酒櫃無法操作。
沒有接駁
電源
電器開關關掉了
斷路器跳掣或熔斷。
酒櫃不夠冷.
檢查溫度
控制設
置.
門被打開次數太多。
門沒有完全關閉。
門
密封墊圈沒有妥善封閉。
酒櫃內風扇經常開啟和關閉.
房間溫度比正常熱。
大量酒瓶添
加到酒櫃並阻礙製冷風扇
。
門被打開次數太多。
門没有完全關閉。
溫度
控制設
置不正確。
門
密封墊圈
不正確。
ＬＥＤ燈不亮著.
沒有接駁
電源
斷路器跳掣或熔斷。
ＬＥＤ燈燒壞了。
燈掣按鈕“關閉”.
振動.
檢查以保證酒櫃平放。
酒櫃似乎發出太多的噪音。
在
劇烈震動的噪聲可能來自製冷劑流動，這是正
常
的。
由於每個製冷時期結束時，您可能會聽到在酒櫃
製
冷劑流動潺潺的聲音
。
內壁的收縮和擴張
可能會導致彈出和爆裂聲
響.
酒櫃不是平放。
門沒有正常關
閉。
酒櫃不是平放。
門
被反轉
，安裝不正確。
墊
片骯髒致未能妥善
放置。
層架上錯位置。
15
Please record the following information:
請記錄下列資料
請記錄下列資料請記錄下列資料
請記錄下列資料
Model /
型號
型號型號
型號
Serial No. /
機身編號
機身編號機身編號
機身編號
Name of distributor /
經銷商名稱
經銷商名稱經銷商名稱
經銷商名稱
Date of purchase /
購買日期
購買日期購買日期
購買日期
The manufacturer reserves the right to make any technical
modifications due to product improvement. No prior notice
will be given. If you have any enquiry, please contact our
after-sales department and forgive for any inconvenient.
All information is subjected to English version.
本產品不斷改進中
本產品不斷改進中本產品不斷改進中
本產品不斷改進中，，，，如功能有所更改
如功能有所更改如功能有所更改
如功能有所更改，，，，恕不另行通知
恕不另行通知恕不另行通知
恕不另行通知，，，，如有
如有如有
如有
疑問
疑問疑問
疑問，，，，請與維修中心聯絡
請與維修中心聯絡請與維修中心聯絡
請與維修中心聯絡，，，，不便之處
不便之處不便之處
不便之處，，，，敬請原諒
敬請原諒敬請原諒
敬請原諒。。。。
說明書內容以英文版本為準
說明書內容以英文版本為準說明書內容以英文版本為準
說明書內容以英文版本為準。。。。
香港仔大道
香港仔大道香港仔大道
香港仔大道
232
都工業大廈二樓
都工業大廈二樓都工業大廈二樓
都工業大廈二樓
2/F, Shing Dao Industrial Building,
232 Aberdeen Main Road,Hong Kong
產品查詢
產品查詢產品查詢
產品查詢：：：：
8210 8210 Product information
：：：：
8210 8210
維修安裝
維修安裝維修安裝
維修安裝：：：：
8210 8210 Service Hotline
：：：：
8210 8210
Loading...