Frigidaire Full Size Tumble Action Washers User Manual

Installation

Instructions

Full Size Tumble Action Washers

Before beginning installation, carefully read these instructions. This will simplify the
installation and ensure the washer is installed correctly and safely. Leave these instructions
near the washer after installation for future reference.

NOTE: The electrical service to the washer must conform with local codes and ordinances
and the latest edition of the National Electrical Code, ANSI/NFPA 70.

Contents

For your safety the information in

this manual must be followed to minimize the risk
of fire or explosion or to prevent property damage,
personal injury or loss of life.

- Do not store or use gasoline or other flammable
vapors and liquid in the vicinity of this or any
other appliance.

- WHAT TO DO IF YOU SMELL GAS

· Do not try to light any appliance.

· Do not touch any electrical switch; do not

use any phone in your building.

· Clear the room, building or area of all

occupants.

· Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppliers
instructions.

· If you cannot reach your gas supplier, call

the fire department.

SUBJECT PAGE

Pre-Installation Requirements 2
Electrical Requirements 2
Grounding Requirements 2
Water Supply Requirements 2
Drain Requirements 2
Rough-In Dimensions 3
Location Of Your Washer 4
Unpacking 4
Installation 4-6
Replacement Parts 6

Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.

Printed in U.S.A.

P/N 134594900A (0509)

PRE-INSTALLATION REQUIREMENTS

Tools Required for Installation:

1. Phillips screwdriver

2. 10 mm socket with ratchet.

3. Channel-lock adjustable pliers.

4. Carpenter’s level.

ELECTRICAL REQUIREMENTS

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay
fuse or circuit breaker.

POWER SUPPLY - 2 wire, with ground, 120 volt, single
phase, 60 Hz, Alternating Current. NOTE: The use of this
washer with power created by gas powered generators, solar
powered generators, wind powered generators or any other
generator other than the local utility company is not
recommended.

OUTLET RECEPTACLE - Properly grounded 3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position.

2

ROUGH-IN DIMENSIONS

NOTE: For pedestal or undercounter installation, reference page 5 "Installation".

A

With leveling leg
lock nuts removed

A

3

LOCATION OF YOUR WASHER

DO NOT INSTALL YOUR WASHER:

1. In an area exposed to dripping water or outside
weather conditions. The ambient temperature should
never be below 60 ° F (15.6 ° C) for proper washer
(detergent breakdown) operation.

2. In an area where it will come in contact with curtains
or drapes.

3. In an area (garage or garage-type building) where
gasoline of other flammables are kept or stored
(including automobiles).

4. On carpet. Floor MUST be solid with a maximum
slope of 1/2 in. per foot (1.27 cm per 30.5 cm). To
ensure vibration or movement does not occur,
reinforcement of the floor may be necessary.

IMPORTANT
MINIMUM INSTALLATION CLEARANCES
When installed in alcove or closet:

Sides, Rear = 0 in. (0 cm)
Top = 0 in. (0 cm)
When installed in closet: Front = 1 in. (2.54 cm)
Closet door ventilation required: 2 louvered openings each
60 in2 (387 cm2), 3 in. (7.6 cm) from top and bottom of
door.

UNPACKING

7. Cover the bolt holes with plugs located in the
literature bag.

8. Using the shipping posts, prop up the front of the
washer approximatley 2 inches to gain access to
the service panel screws.

9. Remove the 2 screws and remove the service panel.

1. Cut the shipping carton along the dotted line along
the base of the unit.

2. While in the carton carefully lay the washer on its
back side.

3. Remove the styrofoam base.

4. Carefully return the washer to an upright position
and remove the carton.

5. Carefully move the washer to within 4 feet (122cm)
of the final location.

6. Remove the following from the back panel of the
washer: 4 packaging bolts,

4 spacers,

2 metal "P" clamps,

POWER CORD

Remove:
4 packaging bolts,
4 spacers.
metal "P" clamps,

10. Remove the two (2) styrofoam blocks located under
the drum. Lift up on the drum, tilt the base of the
foam blocks inwards toward the rear of the washer
until free, then pull them out.

11. Replace the service panel and screws.
NOTE: If the washer is to be transported at a later

date, the shipping support hardware must
be reinstalled to prevent shipping damage.

Drain Hose Installation

The drain hose is field installed to allow hose orientation
to the left or right, up or down depending on location of
the house drain. The hose is shipped in the washer tub
with the spring clamp on the coupler elbow and drain
hose hanger installed on the end of the hose.

1. Remove the drain hose from the tub of the washer.

2. Push the hose onto the drain coupler at the upper
left of the washer back panel until the hose con­tacts the STOP RIB.

4