Frigidaire FRTB7B4EMB3, FRTB7B4EMB2 Owner’s Manual

_iiiii

Welcome ..................................... 2

Safety _nstructions .................... 3

_nsta_iation ................................. 4-5

Door Reversal ............................. 6

Features At A Glance ................. 7

Temperature Controls ................. 7

First Steps .................................. 8-12

Helpful Hints ............................... 13

Beverage Center Extra

Features ...................................... 13

Optional _ce Service ................... 14

Energy Saving Tips ..................... 15

Vacation and Moving Tips .......... 15

Norma_ Operating Sounds .......... 16

Care & C_eaning .......................... 17-18

Warranty _nformation .................. 19

Troubleshooting ......................... 20-21

Before You Cal_ ........................... 22

READ AND SAVE THESE INSTRUCTIONS P!. 241_9ssoo(o_o_)

Congratuiations on your purchase of a new beverage center! We here at Electrolux Home Products, inc. are very proud of our product and we are compIetely committed to providing you with the best service possible. Your satisfaction is our #1 priority.

Please read this Use & Care Manual very carefuiIy. It contains

valuable information on how to properly maintain your new beverage center.

We know you'll enjoy your new beverage center and Thank You for choosing our product. We hope you consider us for future purchases.

PLEASE READ AND SAVETNESE INSTRUCTIONS

This Use & Care Manual provides specific operating instructions for your model. Use your beverage center only as instructed in this manual. These instructions are not meant to

cover every possible condition and situation that may occur. Common sense and caution must be practiced when instailing, operating and maintaining any appliance.

Pmeaserecord your modeB and serial numbers below for future reference.This information is found on your seriaB plate located inside the refrigerator compartment.

Questions?

1-800-944-9044

(United States)

1-800-285-8352

(Canada)

Extend Your Warranty Protection

With An

Extended Service Contract

CALL 1-800-944-9044

To Enjoy These Benefits:

TotaJ freedom from repair bills so unexpected repairs won't upset your budget,

Fast, convenient toll-free service is just a phone call away,

Model Number:

Seriai Number:

Purchase Date:

ii o

i ! i ! ! i i i i! i ii!i i!i! ! i i ii ! i!i i! iiiiiiiiiiiiiiiiiii!i i !i!ii!i !i!!!!!i! i!!i!!!i!i ! !!!!i! !i! i!ii iiiiiiiiiiiiiiiiiiiiiiii i

PLEASE COMPLETE AND MAIL INTHE

PRODUCT REGISTRATION CARD

INCLUDEDWFHYOUR BEVERAGE CENTER,

Top-quaJity repairs by factory-trained experts,

Quick access to genuine replacement parts so you can rest assured your Beverage Center is repaired with the proper components,

Please attacn sales receLpl

he,e for future reference.

FORYOURSAFETY

,, Donotstoreorusegasoline,orotherflammableliquids

inthevicinityofthisoranyotherappliance.Readproduct labelsforwarningsregardingflammabilityandother

hazards.

+ Donotoperatethebeveragecenterinthepresenseof

explosivefumes.

+ Avoidcontactwithanymovingpartsoftheautomaticice

maker.(somemodels)

CHILDSAFETY Destroyorrecyciethecarton,plasticbags,andanyexterior

wrappingmaterialimmediatelyafterthisbeveragecenteris

unpacked.ChildrenshouldNEVERusetheseitemstoplay with.Cartonscoveredwithrugs,bedspreads,plasticsheetsor stretchwrapmaybecomeairtightchambers,andcanquickly

causesuffocation.

PROPER DISPOSAL OFYOUR BEVERAGE CENTER

Risk of child entrapment Child entrapment and

suffocation are not probiems of the past. Junked or abandoned

refrigerators or freezers are stt dangerous - even if they will sit for "just a few days." If you are

getting rid of your oId refrigeralor or freezer, please foiIow the instructions below to help prevent accidents.

Before you throw away your omdrefrigerator/freezer:

. Remove doors.

Leave shelves in place so children may not easily climb inside+

Nave refrigerant removed by a qualified service technician.

ELECTRICAL INFORMATION

+ The beverage center must be plugged into its own

dedicated 115 Vomt,60 Bz. AC only electric outmet, The power cord of the appliance is equipped with a three-

prong grounding ptug for your protection against electrical shock hazards+ It must be pIugged directly into a properly grounded three-prong receptacle+ The receptacle must be

installed in accordance with Iocal codes and ordinances. ConsuIt a quatified electrician+ Do not use an extension

cord or adapter pBug,

+ If the power cord is damaged, it should be replaced by the

manufacturer, service technician or a qualified person to prevent any risk+

+ Never unpiug this beverage center by pulling on the

power cord+ Always grip the plug firmiy_ and pull straight out from the receptacle to prevent damaging the power

cord+

,, UnpIug this beverage center before cieaning and before

replacing a light bulb to avoid electrical shock+

+ Performance may be affected if the voltage varies by 10%

or more+ Operating this beverage center with insufficient power can damage the compressor. Such damage is not

covered under your warranty+

,, Do not plug the unit into an outlet controlled by a wall

switch or pull cord to prevent this beverage center from being turned off accidentalIy+

,, Avoid connecting this beverage center to a Ground Fault

Interruptor (GFI) circuit+

ThisUse&CareManualprovidesspecificoperating instructionsforyourmodel.Usethisbeveragecenteronlyas instructedinthisUse&CareManual.Beforestartingthis

beveragecenter,followtheseimportantfirststeps. LOCATION

, Chooseaplacethatisnearagroundedelectricaloutlet.

DoNotuseanextensioncordoranadapterplug.

o Ifpossible,placethisbeveragecenteroutofdirect

sunlightandawayfromtherange,dishwasherorother

heatsources.

o Thisbeveragecentermustbeinstalledonafloorthatis

levelandstrongenoughtosupportafullyloaded

beveragecenter.

, Considerwatersupplyavailabilityformodelsequipped

withanautomaticicemaker.

LEVELING

All four corners of your beverage center must rest firmly on a solid floor. Your beverage center is equipped with adjustable

leveling screws to help level your unit. To Leve! Your

Beverage Center:

1. Remove toe grille.

2. Use adjustable wrench to adjust leveling screws.

INSTALLATION

Installation Clearances

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical

connections:

Sides & Top 3/8" Back 1"

DOOR OPENING

Your beverage center should be positioned to allow easy

access to a counter when removing food. To make this possible, the direction in which the doors open can be reversed. See Door Removal & Reversal Instructions.

To Connect Water Supply LineTo ice Maker inJetVaJve

1= Disconnect beverage center from electric power source= 2= Place end of water supply line into sink or bucket. Turn ON

water supply and flush supply line until water is clear=Turn OFF water supply at shutoff valve=

3= Unscrew plastic cap from water valve inlet and discard

cap.

4= Slide brass compression nut, then ferrule (sleeve) onto

water supply line, as shown=

5= Push water supply line into water valve inlet as far as it

will go (¼ inch)= Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve= Tighten another

half turn with a wrench; DO NOT over tighten=

6= With stee! clamp and screw, secure water supply line to

rear panel of beverage center as shown=

7= Coil excess water supply line (about 2½ turns) behind

beverage center as shown and arrange coils so they do not vibrate or wear against any other surface=

8= Turn ON water supply at shutoff valve and tighten any

connections that leak=

9= Reconnect beverage center to electrical power source= 10= To turn ice maker on, lower wire signal arm (see ice

maker front cover for ON/OFF position of arm).

Plastic Water

Tubing to _ceMake{

Brass

Comeressior

Before lnstaHingTheWater Supply Line,You Will Need ,' Basic Tooms: adjustabIe wrench, flat-blade screwdriver,

and Phillipd rMscrewdriver

,, Access to a household cold water line with water pressure

between 30 and 100 psi=

* A water supply line made of ¼ inch (6=4mm) OD, copper

tubing= To determine the length of copper tubing needed, you will need to measure the distance from the ice maker

inlet valve at the back of the beverage center to your cotd water pipe=Then add approximately 7 feet (2=1meters), so the beverage center can be moved out for cleaning (as

shown).

* A shutoff valve to connect the water supply line to your

household water system= DO NOT use a self-piercing type shutoff valve=

,, A compression nut and ferrule (sleeve) for connecting the

water supply line to the ice maker inlet valve.

from household water supply

qndude enough tubing in oop to a_bw

mown_ refrigerator out for cleaning v

er Valv6

Bracket

DoorStop Tools Necessary;

Phillips"head

Quadrex head

screwdi[ver

DOOR REMOVAL AND REVERSAL INSTRUCTIONS:

Cabinet Hole Plugs

Hinge

Hole Plug

1. Remove toe grille.

Door Stop Screw

Door Stop

Screw- (

Center

Iinge

H01ePlugs

iL f

2. Remove top hinge with 3/8" hex driver and lift freezer door off of center

3. Unscrew center hinge pin using adjustable wrench and save for

4. Lift refrigerator door off of bottom hinge and set aside.

5. Remove center hinge and shim by removing inside screw and

6. Loosen two outside screws on opposite side of refrigerator, remove inside

7. Remove two screws on bottom hinge with 3/8" socket wrench.

8. InstalI bottom hinge on opposite side with the two screws removed from

9. Unscrew bottom hinge pin using adjustable wrench. Move hinge pin to

10. Move beverage center door stops to opposite side. Before starting screws,

11. Position beverage center door onto bottom hinge pin and screw center

12. Tighten center hinge pin with adjustable wrench.

13. Remove cabinet and hinge hole plugs and move to opposite side.

14. Lower freezer door onto center hinge pin.

15. Close freezer door. Have an assistant lift up on opposite side of door while

16. Replace toe grille.

17. Plug in electrical power cord and turn beverage center temperature

Awl

Socket Adjustable

Wrench Set Wrench

hinge pin. Set door aside.

reassembly. Ensure plastic washer stays on hinge pin.

loosening two outside screws enough to allow hinge and shim to slide out. Tighten screws.

screw and install center hinge.

step 7.

other hole in hinge and tighten with adjustable wrench.

use an awl to puncture the foam.

hinge pin through center hinge into top of door. Close beverage center door to help align hinge hole.

tightening screws to install top hinge.

control to the "5" position. Adjust setting as necessary.

Ice Maker

ice BtJcket

Air Flow Control

Temperature

Features may vary

Control --

according to model

Shelf --

Shelf rower--

Keg Support.

Shelf

Slide Out-- Baskets

COOL DOWN PERIOD

To ensure safe food storage, allow the beverage center to operate with the doors closed for at least 12 hours before

loading it with food and beverages. BEVERAGE CENTER CONTROLS

Temperature Control

This rotary control is the primary control for the refrigerated compartment temperature. If the beverage center is too warm, adjust this control in the "Colder" direction, if the beverage

center is too cold, adjust this control in the "Cold" direction.

Air Ftow Control

This rotary control is the primary control for the freezer compartment temperature. If the freezer is too warm, adjust this control in the "Colder" direction. If the freezer is too cold, adjust

this control in the "Cold" direction.

TEMPERATURE SETTING AND ADJUSTMENT

For beer storage, the recommended initial setting is 5. Under most conditions, this setting will provide for dispensed beer between 34-38 ° RYou may adjust as required to suit your individual taste and the beverage center operating conditions. After a controm adjustment, aBways allow 24 hours for the

beer to stabilize at the new temperature before making additionam adjustments.

Opening

Tern )erature Control (some models)

Air Flow Control (some models)

To maintain temperatures, a fan circulates air in the beverage center compartments. For good circulation, do not block cold air vents with food items.

+ 15 hidden pages