Use & Care Manual
Side by Side
Welcome 2
Refrigerator
With Electronic Controls
Safety Instructions
Installation --
Ice Maker To Water Supply
Door Removal
Instructions
Features at a Glance
Temperature Controls
Looking Inside
Automatic Ice and Water
Dispenser
Includes Connecting
3
4-5
6
7
8-11
12-14
15-19
Español
READ AND SAVE THESE INSTRUCTIONS
30
Food Storage
& Energy Saving Tips
Normal Operating Sounds
Care & Cleaning
Warranty
Before You Call
Solutions to
Common Problems
22-23
25-29
P/N 241622400A (0501)
20
21
24
Welcome & Congratulations
Congratulations on your purchase of a new refrigerator! We
here at Electrolux Home Products are very proud of our
product and we are completely committed to providing you
with the best service possible. Your satisfaction is our #1
priority.
Please read this Use & Care Manual very carefully. It contains
valuable information on how to properly maintain your new
refrigerator.
We know you’ll enjoy your new refrigerator and Thank You
for choosing our product. We hope you consider us for future
purchases.
PLEASE READ AND SAVE THESE INSTRUCTIONS
This Use & Care Manual provides specific operating
instructions for your model. Use your refrigerator only as
instructed in this manual. These instructions are not meant
to cover every possible condition and situation that may
occur. Common sense and caution must be practiced when
installing, operating and maintaining any appliance.
Please record your model and serial numbers below for
future reference. This information is found on the serial
plate located inside the refrigerator compartment.
Questions?
1-800-944-9044
(United States)
1-866-213-9397
(Canada)
or visit our web site at www.frigidaire.com
Extend Your Warranty Protection
With An
Extended Service Contract
CALL 1-800-944-9044
To Enjoy These Benefits:
• Total freedom from repair bills so
unexpected repairs won’t upset your
budget.
NOTE: Use only soap and water to clean serial plate.
Model Number:
Serial Number:
Purchase Date:
• Fast, convenient toll-free service is just
a phone call away.
• Top-quality repairs by factory-trained
experts.
• Quick access to genuine replacement
parts so you can rest assured your
refrigerator is repaired with the proper
components.
Please attach sales receipt
here for future reference.
Please complete and mail in the
Registration Card
included with your
refrigerator.
Product
2
Important Safety Instructions
Please Read All Instructions Before Using This Refrigerator.
FOR YOUR SAFETY
• Do not store or use gasoline, or other flammable liquids
in the vicinity of this or any other appliance. Read
product labels for warnings regarding flammability and
other hazards.
• Do not operate the refrigerator in the presence of
explosive fumes.
• Avoid contact with any moving parts of automatic ice
maker.
• Remove all staples from the carton. Staples can cause
severe cuts, and also destroy finishes if they come in
contact with other appliances or furniture.
CHILD SAFETY
Destroy or recycle the carton, plastic bags, and any exterior
wrapping material immediately after the refrigerator is
unpacked. Children should NEVER use these items to play
with. Cartons covered with rugs, bedspreads, plastic sheets
or stretch wrap may become airtight chambers, and can
quickly cause suffocation.
These Guidelines Must Be Followed To Ensure That Safety Mechanisms In This Refrigerator
Will Operate Properly.
PROPER DISPOSAL OF YOUR REFRIGERATOR
OR FREEZER
Risk of child entrapment
Child entrapment and suffocation
are not problems of the past.
Junked or abandoned refrigerators
or freezers are still dangerous –
even if they will sit for “just a few
days.” If you are getting rid of your
old refrigerator or freezer, please
follow the instructions below to
help prevent accidents.
Before you throw away your old refrigerator/ freezer:
• Remove doors.
• Leave shelves in place so children may not easily climb
inside.
• Have refrigerant removed by a qualified service
technician.
ELECTRICAL INFORMATION
• The refrigerator must be plugged into its own
dedicated 115 Volt, 60 Hz., AC only electric outlet.
The power cord of the appliance is equipped with a
three-prong grounding plug for your protection against
electrical shock hazards. It must be plugged directly
into a properly grounded three-prong receptacle. The
receptacle must be installed in accordance with local
codes and ordinances. Consult a qualified electrician.
Do not use an extension cord or adapter plug.
• If the power cord is damaged, it should be replaced by the
manufacturer, service technician or a qualified person to
prevent any risk.
• Never unplug the refrigerator by pulling on the power
cord. Always grip the plug firmly, and pull straight out
from the receptacle to prevent damaging the power cord.
• Unplug the refrigerator before cleaning and before
replacing a light bulb to avoid electrical shock.
• Performance may be affected if the voltage varies by
10% or more. Operating the refrigerator with insufficient
power can damage the compressor. Such damage is
not covered under your warranty.
• Do not plug the unit into an outlet controlled by a wall
switch or pull cord to prevent the refrigerator from being
turned off accidentally.
• Avoid connecting refrigerator to a Ground Fault Interruptor
(GFI) circuit.
IMPORTANT: Pressing and holding the On/Off button
for 3 seconds, located on the left side of the
temperature control panel, will disable your
refrigerator’s cooling system, but does not disconnect
the power to the light bulb and other electrical
components. To turn off power to your refrigerator you
must unplug the power cord from the wall outlet.
3
This Owner’s Guide provides specific operating instructions
for your model. Use the refrigerator only as instructed in this
Use & Care Manual. Before starting the refrigerator, follow
these important first steps.
LOCATION
• Choose a place that is near a grounded electrical outlet.
Do Not use an extension cord or an adapter plug.
• If possible, place the refrigerator out of direct sunlight
and away from the range, dishwasher or other heat
sources.
• The refrigerator must be installed on a floor that is level
and strong enough to support a fully loaded refrigerator.
• Consider water supply availability for models equipped
with an automatic ice maker.
INSTALLATION
Do Not install the refrigerator where
the temperature will drop below 55°F (13°C) or rise
above 110°F (43°C). The compressor will not be able
to maintain proper temperatures inside the
refrigerator.
4
Installation
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator
from electrical power before connecting a water supply line to the refrigerator.
To Avoid Property Damage:
• Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not
recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible
for any damage if plastic tubing is used for supply line.
• DO NOT install water supply tubing in areas where temperatures fall below freezing.
• Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft
water, ensure that the softener is maintained and working properly.
IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.
Before Installing The Water Supply Line, You Will Need
• Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver
• Access to a household cold water line with water pressure between 20 and 100 psi.
• A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed,
you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water
pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).
• A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type
shutoff valve.
• A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.
- Connecting Ice Maker To Water Supply
NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6
meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2)
ferrules/sleeves, and instructions for installing a water supply line.
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket. Turn ON water supply
and flush supply line until water is clear. Turn OFF water supply at shut
off valve.
3. Unscrew plastic cap from water valve inlet and discard cap.
4. Slide brass compression nut, then ferrule (sleeve) onto water supply line,
as shown.
5. Push water supply line into water valve inlet as far as it will go (¼ inch).
Slide ferrule (sleeve) into valve inlet and finger tighten compression nut
onto valve. Tighten another half turn with a wrench; DO NOT over tighten.
6. With steel clamp and screw, secure water supply line to rear panel of
refrigerator as shown.
7. Coil excess water supply line (about 2½ turns) behind refrigerator as shown
and arrange coils so they do not vibrate or wear against any other surface.
8. Turn ON water supply at shutoff valve and tighten any connections that
leak.
9. Reconnect refrigerator to electrical power source.
10. Make sure ice maker power switch is turned On (See page 13 for location of
power switch).
IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may
cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be
discolored or have poor flavor. Discard ice made during the first 24 hours.
5
Door Removal Instructions
DOOR REMOVAL INSTRUCTIONS:
If it is necessary to move the refrigerator through narrow doorways, follow
these steps to remove the doors.
6
Features At A Glance
Features may vary according to model
7
Controls & Settings
8
Controls & Settings
Making Temperature Adjustments
After running your refrigerator for 24 hours, you can adjust temperatures as needed. Make your adjustments
small and gradual, allowing time for temperatures to change and stabilize. Refer to the following guidelines
for temperature settings.
Choosing Fahrenheit or Centigrade
Depending on which temperature standard you
prefer to use, you can set your control panel to
display in fahrenheit or centigrade. To change
between fahrenheit and centigrade, press the Mode
button (located between the two digital temperature
displays).
Press to alternate between
Fahrenheit and Centigrade
What To Do If The Temperature Displays Flash
If either display is continuously flashing, it may indicate that the control system has detected a performance
problem. Call your Electrolux service representative, who can interpret the flashing message.
Numeric Display
Freezer
Fresh
Food
Warmest 1 1
Factory Setting 5 5
Coldest 9 9
Temperature Adjustment Guide
If Fresh Food compartment is too warm
If Fresh Food compartment is too cold
If Freezer compartment is too warm
If Freezer compartment is too cold
Temperature Display (2-Digit)
Freezer Fresh Food
F° C° F° C°
Warmest 6° -14° 47° 8°
Factory Setting 0° -18° 37° 3°
Coldest -6° -21° 33° 1°
Adjust Fresh Food control one degree
colder by pressing Down (Colder) button.
Adjust Fresh Food control one degree
warmer by pressing the Up (Cold) button.
Adjust Freezer control one degree colder
by pressing Down (Colder) button.
Adjust Freezer control one degree warmer
by pressing the Up (Cold) button.
9
Controls & Settings
SYSTEM-MONITORING ALARMS
The electronic control system continuously monitors
your refrigerator/freezer for temperature consistency
and doors left ajar. Variances from normal operating
conditions are communicated by audible tones and
a set of two status indicator lights.
Responding to Alarms (Audible Tones &
Indicator Lights)
Your refrigerator’s control system can convey the
following information through audible tones and the
alarm indicator lights.
Door
Ajar
Flashing
Green
Freezer or Fresh Food
door has been open for
over five minutes.
NONO
TETE
NO
TE
NONO
TETE
Each time you make settings on the control panel, a
single audible tone acknowledges your input.
Close door to silence and reset alarm.
Air Filter Indicator & Status Lights
Your refrigerator’s fresh food air filter needs to be replaced from time to time. You can monitor the need for
replacement by referring to the status light while the air filter is “ON”. To turn on the air filter, press the “Air
Filter” button. To turn off the air filter, press the “Air Filter” button. To RESET the air filter, press the “Air
Filter” button and hold for 3 seconds.
Air Filter Status Light (not available on all models)
Green
Filter OK.
Yellow
Red
Air filter is about 80 percent used. Please order new one.
Air filter is 100 percent used. Please change now.
10
Controls & Settings
TURNING THE COOLING SYSTEM ON AND OFF
You can disable the cooling system in your
refrigerator by pressing the On/Off button located on
the left side of the temperature control panel.
To ensure that you do not accidentally turn off the
cooling system, the button does not work unless you
press and hold it for three seconds.
While the cooling system is “OFF”, the digital display
will show “OF” “OF” for temperature display models
and “O” “F” for numeric display models.
Once you disable the cooling system, all
refrigeration to the freezer and fresh food
compartments stops.
To turn the cooling system back on, you must again
press and hold the On/Off button for three more
seconds.
IMPORIMPOR
IMPOR
IMPORIMPOR
The On/Off button only controls your refrigerator’s cooling system. Power to lights and other electrical
components continue unless you unplug the power cord.
TT
ANTANT
T
ANT
TT
ANTANT
Cooling System On/Off Button
11
Looking Inside
1
2
PIZZA SHELF (SOME MODELS)
This shelf is attached to the freezer wall beside the ice dispenser container.
This convenient area allows for storage of pizza and other tall items placed
vertically between the ice dispenser container and the freezer wall.
ICE CREAM SHELF (SOME MODELS)
This shelf attaches to the top of the ice dispenser container. It allows storage
of both round and rectangular cartons of your favorite ice cream.
TIP-UP SHELF (SOME MODELS)
A Tip-Up shelf in the freezer section allows tall items to be easily stored.
To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break suddenly if
nicked, scratched, or exposed to sudden temperature change.
Pizza Shelf
Ice Cream Shelf
Cantilever Glass Shelf
Cantilever Sliding Glass Shelf
12
Looking Inside
(continued)
DOOR STORAGE
Door bins and shelves are provided for convenient storage
of jars, bottles, and cans. Frequently used items can be
quickly selected.
Some models have door bins that can accommodate
gallon-sized plastic drink containers and economy-sized
jars and containers. Some bins are adjustable for
maximum storage capacity.
The dairy compartment, which is warmer than the general
food storage section, is intended for short term storage of
cheese, spreads, or butter.
ADJUSTABLE DOOR BINS
Some models have adjustable door bins that can be
moved to suit individual needs.
To move door bins
1. Lift bin straight up.
2. Remove bin.
3. Place bin in desired position.
4. Lower bin onto supports until locked in place.
Fixed Door Bin
Adjustable Door Bin
SPECIAL ITEM RACK (SOME MODELS)
The innovative design of the Special Item Rack allows
you to store a six-pack of 12 ounce drink cans, a bottle of
wine, a two-liter soft drink bottle, or a carton of eggs. The
Special Item Rack mounts on the left side of your
refrigerator. To install, just slide the Special Item Rack
onto any shelf as shown in the drawing.
13
Looking Inside -
Special Storage Areas
CRISPERS (SOME MODELS)
The crispers, located under the bottom refrigerator shelf,
are designed for storing fruits, vegetables, and other fresh
produce. Wash items in clear water and remove excess water
before placing them in the crispers. Items with strong odors
or high moisture content should be wrapped before storing.
Crisper Drawer
MEAT KEEPER (SOME MODELS)
Some models are equipped with a Meat Keeper. Meat Keeper
temperatures can be adjusted by sliding the Meat Keeper
Temperature Control in either direction. Use this pan for short
term storage of bulk meat items. If meats are to be kept
longer than one or two days, they should be frozen. The
Meat Keeper is fixed and cannot be moved up or down. If
fruits or vegetables are to be stored in the Meat Keeper, set
the Meat Keeper Temperature Control to a warmer setting to
prevent freezing.
HUMIDITY CONTROL (SOME MODELS)
The Humidity Control, present on some models with crisper
drawers, allows you to adjust the humidity within the crisper.
This can extend the life of fresh vegetables that keep best
in high humidity.
NOTE: Leafy vegetables keep best when stored with
the Humidity Control set on Higher Humidity, or in a
drawer without a Humidity Control. This keeps incoming
air to a minimum and maintains maximum moisture
content.
Crisper Humidity Control
DELI DRAWER (SOME MODELS)
Some models are equipped with a Deli Drawer for storage of
luncheon meats, spreads, cheeses, and other deli items.
Meat Keeper with Temperature Control
WINE RACK (SOME MODELS)
The wine rack stores bottles of wine, or single two-liter plastic
bottles of juice or soda pop. To install, slide the Wine Rack
onto the shelf with the curve facing in. To remove, slide the
Wine Rack out. Install on either side of shelf.
Wine Rack
14
Automatic Ice and Water Dispenser
AUTOMATIC ICE & WATER DISPENSER OPERATING INSTRUCTIONS
EXTREME To freeze food at a faster rate to preserve freshness, push the Touch Pad for 3-5 seconds to
FREEZE activate this feature. A green light will appear above the Touch Pad. Push the Touch Pad again
for 3-5 seconds to deactivate.
EXTRA To increase ice production for special occasions, such as parties, push the Touch Pad for
ICE 3-5 seconds to activate this feature. A green light will appear above the Touch Pad. Push the
Touch Pad again for 3-5 seconds to deactivate.
CUBE Press the CUBE Touch Pad to get cubed ice. A green light will appear above the Touch Pad.
Press glass against ICE dispensing paddle as far up as possible to catch all ice.
CRUSH Press the CRUSH Touch Pad to get crushed ice. A green light will appear above the Touch Pad.
Press glass against ICE dispensing paddle as far up as possible to catch all ice.
LIGHT Press the LIGHT Touch Pad to turn on dispenser light. Press again to turn the light off.
The light also turns on automatically when ice and/or water is dispensed. Replace light bulb with
an appliance bulb of the same wattage.
FILTER The FILTER STATUS indicator light above the Touch Pad will light up each time the dispenser
STATUS is used. The following filter light indications are:
Green The filter is still operating within its specified life cycle.
Amber The filter has reached approximately 80% of its useful life. This is the recommended time
to purchase a replacement filter.
Red The filter is 100% used up. Change the filter as soon as possible.
After the filter cartridge has been changed, press and hold the FILTER RESET Touch Pad for
10-15 seconds.
NOTE: The Green, Red and Amber lights will flash when reset is completed.
2
LOCK The Ice & Water Dispenser can be locked out to prevent unwanted use.
To Lock Out Press the LOCK Touch Pad for 3-5 seconds. A Red light will appear above
the Touch Pad.
To Unlock Press the LOCK Touch Pad for 3-5 seconds until the Red light above the
Touch Pad goes out.
WATER To operate the water dispenser, press a glass against the WATER dispensing paddle . To
stop dispensing water, pull the glass away from the dispensing paddle . Dispensed water is not
cold. For colder water, add crushed ice or cubes before dispensing water. A drip tray located at
the base of the dispenser catches small spills and allows them to evaporate. This drip tray is
removable and dishwasher safe. Do not pour water and excess ice in this area because there
is no drain.
15
Automatic Ice and Water Dispenser
ICE AND WATER DISPENSER FEATURES
The ice and water dispenser conveniently dispenses chilled water, and ice cubes or crushed ice, depending on the model.
To operate the ice dispenser, select the ice option desired using the touchpad. Press a glass against the dispensing paddle
as far up as possible to catch all ice. To stop dispensing ice, pull glass away from dispensing paddle. Do not remove the
glass until the ice has completely dispensed. (Complete instructions for the dispenser operation are attached to the inside
of the freezer door.)
How the Water Dispenser Works
The water tank, located behind the drawers in the refrigerator compartment, automatically fills as water is dispensed. For
proper dispenser operation, the recommended supply water pressure should fall between 20 psi and 100 psi.
Water pressure must not exceed 100 lbs. Excessive pressure may cause water filter to malfunction.
After the refrigerator is connected to the water supply, fill the water tank by drawing one glass of water. It may take about
1½ minutes after activating the dispenser paddle before water begins to fill this first glass. Continue flushing the system
for 3 minutes to rid the tank and plumbing connections of any impurities. The water dispenser has a built in shutoff device
that will stop the water flow after 3 minutes of continuous use. Simply release the dispenser paddle to reset the shutoff
mechanism.
Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected
to soft water, ensure that the softener is maintained and working properly.
How the Ice Dispenser Works
The ice maker and container are located in the top of the freezer compartment. After the
refrigerator is installed properly and has cooled for several hours, the ice maker can begin
making ice within 24 hours. Air in new plumbing lines may cause the ice maker to cycle two
or three times before making a full tray of ice. Ice production is controlled by the ice
maker’s On/Off power switch. Press the switch to the “O” position to turn it Off and press it
to the “I” position to turn it On. With no usage it will take approximately 2 days to fill the ice
container. The ice maker also has a built-in wire signal arm,which automatically stops ice
production when the ice bin is full. This signal arm should not be used to manually stop the
ice maker.
The ice maker produces 4 to 6 pounds of ice every 24 hours depending on usage conditions.
Ice is produced at a rate of 8 cubes every 75 to 90 minutes.
Because of new plumbing connections, the first production of ice cubes may be discolored or have an odd flavor. These
should be discarded until the cubes made are free of discoloration and taste.
16
Automatic Ice and Water Dispenser
• If a large quantity of ice is needed at one time, it is best to remove cubes directly from the ice container.
• The following sounds are normal when the ice maker is operating:
• Motor running
• Ice dropping into ice container
• Water valve opening or closing
• Ice loosening from tray
• Running water
• Turn Off the ice maker when cleaning the freezer and during vacations.
• If the ice maker will be turned off for a long period of time, you should also turn off the water supply valve.
17
Automatic Ice and Water Dispenser
PureSource TM * Ice and Water Filter (some models)
NOTE: If you purchased a refrigerator with a
and care information.
This ice and water filter system filters water to your ice maker and water dispenser. It is
PureSource
located in the upper right back corner of the fresh food compartment.
System Startup:
Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter. The filter
cartridge has already been installed in the filter housing at the factory. Refer to the
to properly fill the system with water.
Changing the Filter:
Water conditions vary throughout the world, but changing the water filter every
6 - 9 months normally will ensure the highest possible water quality. The Filter
Status light will turn red after 400 gallons of water has flowed through the ice and
water dispenser (some models). Also, if the filter has been in a refrigerator that
has not been in use for awhile (during moving for example), change the filter
before reinstalling the refrigerator. The dispenser system will also operate without
filtration (with filter cartridge removed).
To change filter:
It is not necessary to turn the water supply off to change the filter.
1. Open freezer door and leave open until filter change is complete.
2. Turn the ice maker’s power switch to the Off (“O”) position (See illustration
on page 16).
3. Hold filter cup firmly, and unscrew towards left (Some water could
leak out as you remove cup. This is normal.). Filter cartridge should come
down with cup. If cartridge remains in housing, pull down gently, while
twisting filter back and forth.
4. Rinse out cup under running water.
5. The large o-ring that seals the filter system sets in the o-ring groove
down inside the cup. Should the o-ring fall out during filter cartridge
Order new filter cartridges through the
dealer where you bought the refrigerator,
contact the
1-800-944-9044, or go to our web site at
www.frigidaire.com. It might be good to
order some filter cartridges when you first
install your refrigerator. Be sure to ask for
the
RG-100
cartridge.
the nationally recognized and respected,
not for profit, certification organization for
public health safety. The
system is tested and certified to ANSI/NSF
Standard 42. See performance data sheet
for specifications. This system should not
be used on water that is microbiologically
unsafe or with water of unknown quality
unless the water has been adequately
disinfected before or after traveling through
the filtration system.
• Rated Capacity - 400 gallons
• Rated service flow - .5 GPM
• Maximum Rated Pressure - 100 PSI
• Maximum Operating Temp. - 100° F
* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter
Customer Care Center
PureSource™*
The
PureSource™
2000 Ice and Water Filter
System with the RG-100
cartridge is tested and
certified by NSF International,
replacement
PureSource™*
at
* NGRG-
replacement, simply place it back in the groove prior to screwing the cup
back in place. If the o-ring becomes damaged, you will need to order one
from the
6. Discard old filter cartridge.
7. Remove new filter cartridge from packaging and place in cup. The end
with the small o-ring should be up, out of the cup.
8. Screw cup, with filter, back onto housing. Do Not Use Wrench To Reinstall
Cup. Filter cartridge will self-align as cup is tightened. Be sure cup is
completely tightened with
Tighten Past Stop.
9. Turn the ice maker’s power switch to the On (“I”) position.
10. Check for leaks. Open refrigerator door. Wipe any water droplets from the
filter cup. Fill a glass with water. If there is a leak, unscrew filter cup, and
reinsert the filter cartridge. Check placement of large O-ring. Reinstall
filter cup, making certain it is tightened completely.
11. To condition filter system and purge air from water line, fill a glass with
water. Continue flushing the system for approximately 3 minutes to assure
that the purest water possible is stored in the water tank.
IMPORTANT: Resetting The Filter Status Light (some models)
After replacing the filter cartridge, it will be necessary to press the
Status
reset button located on the ice and water dispenser. This will reset
the Filter Status light. Push the reset button until the green, red and amber
lights flash (10-15 seconds). Please refer to the complete dispenser
operating instructions attached to the inside of the freezer door.
On models without a
Reminder Stickers included in the envelope that the Use & Care Manual
came in. Choose a dated sticker that indicates 6 - 9 months (depending
on your water quality and usage) from the date of installation. Place the
sticker on the front of the filter cup to remind you when it is time to
change the filter.
TM
* Ice and Water filter, please read the following use
Customer Care Center
PureSource™
Filter Status
18
How The Water Dispenser Works
.
logo facing outward. Do Not
reset button, there is a set of
section
Filter
Automatic Ice and Water Dispenser
PureSource2
NOTE: If you purchased a refrigerator with a
TM
* Ice and Water Front Filter (some models)
PureSource2
TM *
Ice and Water front filter, please read the following
use and care information. This ice and water filter system filters water to your ice maker and water dispenser. It is
located in the upper right front corner of the fresh food compartment.
System Startup:
Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter.
The filter cartridge has already been installed in the filter housing at the factory. Refer to the
Works
section to properly fill the system with water.
How The Water Dispenser
Changing the Filter:
Water conditions vary throughout the world, but changing the water filter every
6 - 9 months normally will ensure the highest possible water quality. The Filter
Status light will turn red after approximately 400 gallons of water has flowed
through the ice and water dispenser. Also, if the filter has been in a refrigerator
that has not been in use for awhile (during moving for example), change the filter
before reinstalling the refrigerator. The dispenser system will also operate without
filtration (with filter cartridge removed and bypass installed).
To change filter:
It is not necessary to turn the water supply off to change the filter.
1. Turn the ice maker’s power switch to the Off (“O”) position (See illustration
on page 16).
2. Push the
to release the filter from the housing. To minimize the possibility of the
filter falling out of the housing during removal, it would be best to hold the
Order new filter cartridges through the
dealer where you bought the refrigerator,
contact the
1-800-944-9044, or go to our web site at
www.frigidaire.com. It might be good to
order some filter cartridges when you first
install your refrigerator. Be sure to ask for
the
FC-100
cartridge.
Customer Care Center
PureSource™*
replacement
at
filter as it moves out toward you.
NOTE: A small amount of water may be released during this operation.
You should have a paper towel or dish cloth handy to wipe up any water
that may drip out of the filter or housing. Two small holes near the back of
the housing have been added for any excess water to escape. It would be
best to clear away any food near this area on the top shelf in advance of
removing the filter.
3. Pull the old filter cartridge straight out of the housing.
4. Discard the old filter.
5. Remove the new filter cartridge from the packaging and insert into the
The
PureSource2
Water Filter System NGFC
2000 with the
cartridge FC 100 is tested and
certified by NSF International,
the nationally recognized and respected,
not for profit, certification organization for
public health safety. The
Filter system is tested and certified to ANSI/
NSF Standards 42 and 53. See
performance data sheet for specifications.
This system should not be used on water
that is microbiologically unsafe or with water
of unknown quality unless the water has
been adequately disinfected before or after
traveling through the filtration system.
• Rated Capacity - 400 gallons
• Rated service flow - .5 GPM
• Maximum Rated Pressure - 100 PSI
• Maximum Operating Temp. - 100° F
* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter.
TM*
Ice and
PureSource2
PureSource2
TM*
TM*
filter housing the same way the old one came out.
6. When the cartridge is almost in, you will feel it stop against the clip assembly
in the back of the housing. The clip assembly holds the filter cartridge
firmly in place. At this point, you will need to push firmly until the cartridge
snaps fully in place. When completely in place, the front of the filter cartridge
will be flush with the front of the housing.
7. Turn the ice maker’s power switch to the On (“I”) position.
8. Fill a glass with water. As you are doing this, check for leaks at the filter
housing. There will be noticable spurts and sputters as the system pushes
the air out through the system and out the dispenser nozzle. This is normal.
9. After you have run one glass of water, continue to flush the system for
approximately 3 minutes to assure that the purest water possible is stored
in the water storage tank.
IMPORTANT: Resetting The Filter Status Light (some models)
After replacing the filter cartridge, it will be necessary to press the
Reset
Filter Status light. Push the reset button until the green, red and amber
lights flash (10-15 seconds). Please refer to the complete dispenser
operating instructions attached to the inside of the freezer door.
Filter Release Button
, located to the right of the filter cartridge,
button located on the ice and water dispenser. This will reset the
19
Filter
Food Storage & Energy Saving Ideas
FOOD STORAGE IDEAS
Fresh Food Storage
• The fresh food compartment should be kept between 34° F and 40° F with an optimum temperature of 37° F.
• Avoid overcrowding the refrigerator shelves. This reduces the circulation of air around the food and results in uneven
cooling.
Fruits and Vegetables
• Storage in the crisper drawers traps moisture to help preserve the fruit and vegetable quality for longer time periods.
Meat
• Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or surfaces does not
occur.
Frozen Food Storage
• The freezer compartment should be kept at 0° F or lower.
• A freezer operates most efficiently when it is at least 2/3 full.
Packaging Foods for Freezing
• To minimize dehydration and quality deterioration, use aluminum foil, freezer wrap, freezer bags or airtight containers.
Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out,
change color, and develop an off-flavor (freezer burn).
• Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.
• Do not refreeze meat that has completely thawed.
Loading the Freezer
• Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing,
and can raise the temperature of frozen foods.
• Leave a space between the packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.
• Avoid storing hard-to-freeze foods such as ice cream and orange juice on the freezer door shelves. These foods are
best stored in the freezer interior where the temperature varies less.
ENERGY SAVING IDEAS
• Locate the refrigerator in the coolest part of the room, out of direct sunlight,
and away from heating ducts or registers. Do not place the refrigerator
next to heat-producing appliances such as a range, oven, or dishwasher.
If this is not possible, a section of cabinetry or an added layer of insulation
between the two appliances will help the refrigerator operate more
efficiently.
• Level the refrigerator so that the doors close tightly.
• Refer to this Use & Care Manual for the suggested temperature control
settings.
• Periodic cleaning of the condenser will help the refrigerator run more
efficiently. See the
• Do not overcrowd the refrigerator or block cold air vents. Doing so causes
the refrigerator to run longer and use more energy.
• Cover foods and wipe containers dry before placing them in the
refrigerator. This cuts down on moisture build-up inside the unit.
• Organize the refrigerator to reduce door openings. Remove as many
items as needed at one time and close the door as soon as possible.
Care and Cleaning Chart
on page 22.
20
Normal Operating Sounds & Sights
UNDERSTANDING THE SOUNDS YOU MAY HEAR
Your new high-efficiency refrigerator may make unfamiliar
sounds. These are all normal sounds and soon will become
familiar to you. They also indicate your refrigerator is operating
as designed. Hard surfaces, such as vinyl or wood floors,
walls, and kitchen cabinets may make sounds more
noticeable. Listed below are descriptions of some of the most
common sounds you may hear, and what is causing them.
NOTE: Rigid foam insulation is very energy efficient,
but is not a sound insulator.
A. Evaporator
The flow of refrigerant through the evaporator may
create a boiling or gurgling sound.
B. Evaporator Fan
You may hear air being forced through the refrigerator
by the evaporator fan.
C. Defrost Heater
During defrost cycles, water dripping onto the defrost
heater may cause a hissing or sizzling sound. After
defrosting, a popping sound may occur.
IMPORTANT: During the automatic defrost cycle, you
may notice a red glow in the vents on the back wall of
your freezer compartment. This is normal during the
defrost cycle.
21
Care & Cleaning
Keep your refrigerator and freezer clean to prevent odor build-up. Wipe up any spills immediately and clean both sections
at least twice a year. Never use any type of scouring pads, brushes, abrasive cleaners or strong alkaline solutions on
any surface. Do not wash any removable parts in a dishwasher.
wall outlet before cleaning.
• When moving the refrigerator, pull straight out. Do not shift the refrigerator from side to side as this
may tear or gouge the floor covering. If the refrigerator has an automatic ice maker, be careful not to
move the refrigerator beyond the plumbing connections.
• Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp hands.
• Never use CHLORIDE to clean stainless steel.
NOTES:
• The On/Off button on the Electronic Control only controls your refrigerator’s cooling system. To turn off power to
your refrigerator you must unplug the power cord from the wall outlet.
• Do not use razor blades or other sharp instruments which can scratch the appliance surface when removing
adhesive labels. Any glue left from tape or labels can be removed with a mixture of warm water and mild
detergent, or, touch the glue residue with the sticky side of tape you have already removed. Do not remove the
serial plate.
Always unplug the electrical power cord from the
Care & Cleaning Chart
Part What To Use Tips and Precautions
Interior/Door
Liner
Door Gaskets
Drawers/Bins
Glass Shelves
Toe Grille
Exterior and
Handles
Exterior and
Handles
(Stainless Steel
Models Only)
• Soap and water
• Baking soda and water
• Soap and water
• Soap and water
• Soap and water
• Glass cleaner
• Mild liquid sprays
• Soap and water
• Mild liquid sprays
• Vacuum attachment
• Soap and water
• Non Abrasive Glass
Cleaner
• Soap and water
• Ammonia
• Stainless Steel Cleaners
Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to wring
excess water out of sponge or cloth before cleaning around controls,
light bulb or any electrical part.
Wipe gaskets with a clean soft cloth.
Do not wash any removable items (bins, drawers, etc.) in dishwasher.
Allow glass to warm to room temperature before immersing in warm water.
Vacuum dust from front of toe grille. Remove toe grille (See illustration on
page 4). Vacuum backside and wipe with sudsy cloth or sponge. Rinse and
dry.
Do not use commercial household cleaners, ammonia, or alcohol to clean
handles. Use a soft cloth to clean smooth handles. Do Not use a dry cloth to
clean smooth doors.
Never use CHLORIDE to clean stainless steel.
Clean stainless steel front and handles with non-abrasive soapy water and a
dishcloth. Rinse with clean water and a soft cloth. Wipe stubborn spots with an
ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless steel
cleaner. These cleaners can be purchased at most home improvement or
major department stores. Always follow manufacturer's instructions.
NOTE: Always clean, wipe and dry with the grain to prevent cross-grain
scratching. Wash the rest of the cabinet with warm water and mild liquid
detergent. Rinse well, and wipe dry with a clean soft cloth.
22
Care & Cleaning
Refrigerator Light
Located behind
control panel
Wear gloves when replacing light
bulbs to avoid getting cut.
REPLACING LIGHT BULBS
1. Unplug refrigerator.
2. Wear gloves as protection against possible broken
glass.
3. Remove light cover, if necessary.
4. Unscrew and replace old bulb with an appliance bulb
of the same type and wattage.
5. Replace light cover, if necessary.
6. Remember to plug the refrigerator back in.
(continued)
Freezer Light Replacement
23
Warranty Information
REFRIGERATOR WARRANTY
Your refrigerator is protected by this warranty
FULL ONE-YEAR
WARRANTY
LIMITED 2ND-5TH
YEAR WARRANTY
(Cabinet Liner and
Sealed System)
LIMITED
WARRANTY
(Applicable to the
State of Alaska)
WARRANTY
PERIOD
One year from ori ginal
purchase date
Second through fifth
years from original
purchase date
Time periods listed
above.
THROUGH OUR AUTHORIZED SERVICERS,
Pay all costs for repai ring or replacing any parts of this
appliance which prove to be defective in mat erials or
workmanship. Excludes original and replacement Ice
& Water filter cartridges (if equipped). Original and
replacement cartridges are warranted for 30 days
(parts only).
Repair or replace any parts in the cabinet liner or
Sealed Refrigeration System (compressor, condenser,
evaporator, drier and tubing) which prove to be
defective in materials or workmanship.
All of the provisions of the full warranties above and
the exclusions listed below apply.
WE WILL:
THE CONSUMER WILL BE RESPONSIBLE FOR:
Costs of service calls that are listed under
RESPONSIBILITIES OF THE CONSUMER. *
Costs for pick up and delivery of the appliance required because
of service. Costs for labor, parts and transportation other than
with respect to the cabinet liner or Sealed Refrigeration System.
Costs of the technician's travel to the home and any costs for
pick up and delivery of the appliance required because of
service.
NORMAL
In the U.S.A., your appliance is warranted by Electrolux Home Products, Inc. We authorize no person to change or add to any of our
obligations under this warranty. Our obligations for service and parts under this warranty must be performed by us or an authorized
Electrolux Home Products, Inc. servicer. In Canada, your appliance is warranted by Electrolux Canada Corp.
24
1-800-944-9044 (United States)
1-866-213-9397 (Canada)
Before You Call
Visit our web site at
www.frigidaire.com.
PROBLEM CAUSE CORRECTION
RUNNING OF REFRIGERATOR
Compressor does not run.
Refrigerator runs too
much or too long.
• Freezer control is set to "OF".
• Refrigerator is in defrost cycle.
• Plug at wall outlet is
• House fuse blown or tripped
• Power outage.
• Room or outside weather is
• Refrigerator has recently been
• Automatic ice maker is
• Doors are opened too
• Refrigerator/freezer door may
• Freezer control is set too cold
• Refrigerator/freezer gasket is
• Condenser is dirty.
disconnected.
circuit breaker.
hot.
disconnected for a period of
time.
operating.
frequently or too long.
be slightly open.
(control found in refrigerator
section).
dirty, worn, cracked, or poorly
fitted.
• Set freezer control. See Temperature Controls section.
• This is normal for a fully automatic defrost refrigerator.
The defrost cycle occurs periodically, lasting about 30
minutes.
• Ensure plug is tightly pushed into outlet.
• Check/replace fuse with a 15 amp time-delay fuse.
Reset circuit breaker.
• Check house lights. Call local Electric Company.
• It’s normal for the refrigerator to work longer under
these conditions.
• It takes 8-12 hours for the refrigerator to cool down
completely.
• Ice maker operation causes refrigerator to run slightly
more.
• Warm air entering the refrigerator causes it to run
more. Open doors less often.
• Ensure refrigerator is level. Keep food and containers
from blocking door. See PROBLEM section
OPENING/CLOSING OF DOORS/DRAWERS.
• Set refrigerator control to warmer setting until
refrigerator temperature is satisfactory. Allow 24 hours
for temperature to stabilize.
• Clean or change gasket. Leaks in door seal will cause
refrigerator to run longer in order to maintain desired
temperatures.
• Clean condenser. See
and Cleaning section.
Care & Cleaning Chart
in Care
Compressor goes off and
on frequently.
• Thermostat keeps the
refrigerator at a constant
temperature.
TEMPERATURES ARE TOO COLD
Freezer temperature too
cold. Refrigerator
temperature is satisfactory.
Refrigerator temperature
too cold. Freezer
temperature is satisfactory.
Food stored in drawers
freezes.
Food stored in Meat
Keeper freezes (some
models).
Digital temperature
displays are flashing.
• Freezer control is set too cold. • Set freezer control to a warmer setting. Allow 24 hours
• Refrigerator control is set too
cold.
• Refrigerator control is set too
cold.
• Meat Keeper Temperature
Control set too cold.
• Electronic control system has
detected a performance
problem.
• This is normal. Refrigerator goes on and off to keep
temperature constant.
for temperature to stabilize.
• Set refrigerator control to a warmer setting. Allow 24
hours for temperature to stabilize.
• See solution above.
• Adjust Meat Keeper Temperature Control to a lower
setting. (Meat should be stored at a temperature just
below the freezing point for maximum fresh storage
time. It is normal for ice crystals to form due to the
moisture content of meat.)
• Call your Electrolux service representative, who can
interpret any messages or number codes flashing on
the digital displays.
25
Before You Call
(continued)
26
Before You Call (
continued)
PROBLEM CAUSE CORRECTION
AUTOMATIC ICE MAKER
Ice maker is not making
enough ice.
Ice maker will not stop
making ice.
Ice maker is not separating
the ice cubes.
Ice has bad odor and taste.
ICE DISPENSER
(CONTINUED)
• Ice maker is producing less ice
• Freezer is not cold enough.
• Household water line valve is
• Check to see if water
• Ice maker wire signal arm is
• Ice cubes are not being used
• Ice cubes are hollow or smaller
• Ice has picked up odor or
• Water running to ice maker
• Ice not used frequently enough.
than you expect.
not completely open.
dispenser is dispensing slower
than normal.
being held down by some item
in the freezer.
frequently enough.
than normal.
flavor from strong food stored
in refrigerator or freezer.
has poor taste or odor.
• Ice maker should produce approximately 4 – 5 pounds
of ice every 24 hours.
pounds of ice every 24 hours.
• See PROBLEM section TEMPERATURES ARE TOO
WARM.
• Turn on household water line valve.
• If it is, replace the ice & water filter cartridge.
• Move item and release wire signal arm. Remove any
ice cubes that are frozen together over the wire signal
arm.
• Remove and shake ice container to separate cubes.
• The ice & water filter cartridge may be clogged.
Replace filter cartridge.
• Cover foods tightly. Discard stale ice. Ice maker will
produce fresh supply.
• Add filter to water supply line. Consult a water
purifying company.
• Discard stale ice.
Extra Ice
should produce up to 6
Dispenser will not dispense
ice.
Ice dispenser is jammed.
• Ice storage container is empty.
• Freezer temperature is set too
warm.
• Household water line valve is
not open.
• Freezer door is not closed.
• Ice dispensing arm has been
held in for more than 4-5
minutes.
• Ice has melted and frozen
around auger due to infrequent
use, temperature fluctuations,
and/or power outages.
• Ice cubes are jammed
between ice maker and back
of ice container.
• Ice cubes are frozen together.
• Ice cubes are hollow or smaller
than normal.
• When the first supply of ice is dropped into the
container, the dispenser should operate.
• Turn freezer control to a higher setting so that ice
cubes will be made. When first supply of ice is made,
dispenser should operate.
• Open household water line valve. Allow sufficient time
for the ice to be made. When ice is made, the
dispenser should operate.
• Ensure freezer door is closed.
• Motor is overloaded. Motor overload protector will
reset in approximately 3 minutes. Ice can then be
dispensed.
• Remove ice container, thaw, and empty the contents.
Clean container, wipe dry, and replace in proper
position. When new ice is made, dispenser should
operate.
• Remove ice cubes that are jamming the dispenser.
• Use the dispenser often so that cubes do not freeze
together.
• The ice & water filter cartridge could be clogged.
Replace the filter cartridge. Dispensing system
operates best at 20 – 100 psi water pressure. Well
water pressures should fall within this range.
27
Before You Call
(continued)
PROBLEM CAUSE CORRECTION
WATER DISPENSER
Dispenser will not
dispense water.
Water has an odd taste
and/or odor.
Water pressure is
extremely low.
ODORS IN REFRIGERATOR
Interior is dirty.
• Household water line valve is
not open.
• Freezer door is not closed.
• Ice & water filter cartridge is
clogged.
• Front filter not fully installed, if
equipped
• Water has been in the tank for
a period of time.
• Unit not properly connected to
cold water line.
• Tubing used in the household
water supply and installation
may affect water taste and
odor.
• Water has a high mineral
content.
• Cut-off and cut-on pressures
are too low (well systems
only).
• Reverse osmosis system is in
regenerative phase.
• Interior needs to be cleaned.
• Food with strong odors is in
refrigerator.
• Open household water line valve. See PROBLEM
section ICE MAKER IS NOT MAKING ANY ICE.
• Ensure that freezer door is closed.
• Replace filter cartridge.
• Push filter in until you hear a “click”. Filter should be
flush with cabinet.
• Draw and discard 10 – 12 glasses of water to freshen
the supply and completely rinse out the tank.
• Connect unit to cold water line that supplies water to
the kitchen faucet.
• For best results, use copper tubing for water
connections.
• Contact water treatment plant for help.
• Have someone turn up the cut-off and cut-on pressure
on the water pump system (well systems only).
• It is normal for a reverse osmosis system to be below
20 psi during the regenerative phase.
• See
• Cover food tightly.
Care & Cleaning Chart
section.
OPENING/CLOSING OF DOORS/DRAWERS
Door(s) will not close.
Drawers are difficult to
move.
LIGHT BULB IS NOT ON
Light bulb is not on.
• Door was closed too hard,
causing other door to open
slightly.
• Refrigerator is not level. It
rocks on the floor when moved
slightly.
• Refrigerator is touching a wall
or cabinet.
• Food is touching shelf on top
of drawer.
• Track that drawers slide on is
dirty.
• Light bulb is burned out.
• Light switch is stuck.
• No electric current is reaching
refrigerator.
• Close both doors gently.
• Ensure floor is level and solid, and can adequately
support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.
• Ensure floor is level and solid, and can adequately
support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.
• Keep less food in drawer.
• Clean drawer, rollers, and track. See
section.
Chart
• See
• Light switch is located on side of refrigerator and
• See PROBLEM section RUNNING OF
Replacing Light Bulbs
section.
freezer liners.
REFRIGERATOR.
in Care and Cleaning
Care & Cleaning
28
Before You Call
(continued)
IF YOU HEAR:
5 beeps
3 beeps
• A door has been left open for 5
minutes or more.
• The refrigerator has experienced a
loss of power or a low voltage
condition.
• These beeps will repeat once every minute until the
door has been closed. This is normal for the “Door
Ajar” alarm.
• This is normal when “Power-On-Reset” is activated.
29
Loading...