Frigidaire FPBS2777RF4, FPBS2777RF3, FPBS2777RF2, FPBS2777RF1, FPBS2777RF0 Owner’s Manual

...

iiiiiii_iiiiiiiiiiiiiiiiiiiiiiiii

Controls .......

Automatic

www.frigidaire.com USA1-800-944-9044 www,fngidaire.ca Can2

P,easereada,,instructionsbeforeusingthisiiiDoors

refrigerator.

.......................................................................................................................................................................................................................................[] Handles are secure and tight

For your Safety

= DO NOT store or use gasoline, or other

flammable liquids in the vicinity of this or

any other appliance. Read product labels

for warnings regarding flammability and

other hazards. DO NOT operate the refrigerator in the

presence of explosive fumes.

Avoid contact with any moving parts of

automatic ice maker. Remove all staples from the carton. Staples

can cause severe cuts, and also destroy

finishes if they come in contact with other

appliances or furniture.

Definitions

_bThis is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in

IMPORTANT indicates installation, operation or maintenance information which is

important but not hazard-related.

[] Door seals completely to cabinet on all

sides

(3 Freezer drawer is level across the top

Leveling

(3 Refrigerator is level, side-to-side and

tilted 1/4"(6 mm) front-to-back

Q Toe grille is properly attached to

refrigerator

(3 Cabinet is setting solid on all corners

Electrical Power

[] House power turned on [] Refrigerator plugged in

Ice Maker

[] House water supply connected to

refrigerator

[] No water leaks present at all connections

- recheck in 24 hours

[] Ice maker is turned ON [] Ice & water dispenser operates correctly

Final Checks

[] Shipping material removed [] Fresh food and freezer temperatures set [] Crisper humidity controls set [] Registration card sent in

Child Safety

Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the refrigerator is unpacked. Children should NEVER use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation.

Proper Disposal of your Refrigerator or Freezer

Risk of child entrapment

Child entrapment and suffocation are not

problems of the past..Junked or abandoned

refrigerators or freezers are still dangerous

- even if they will sit for "just a few days". If

youaregettingridofyouroldrefrigeratoror freezer,pleasefollowtheinstructionsbelowto helppreventaccidents.

Proper Disposal of Refrigerators/Freezers

We strongly encourage responsibleappliance recycling/disposal methods. Check with your utility company or visit www.energystar.gov/recyde for more information on recycling your old refrigerator.

Before you throw away your old

refrigerator/freezer:

Remove doors.

* Leave shelves

in place so children may not easily climb

inside.

• Have refrigerant removed by a qualified service

technician.

CFC/HCFC Disposal cooling system but does not disconnect the Your old refrigerator may have a coolingsystem power to the light bulb and other electrical

that used CFCsor HCFCs(chlorofluorocarbons .... components. To turn off power to your

or hydrochlorofluorocarbons). CFCs and HCFCs

are believed to harm stratospheric ozone if

released to the atmosphere. Other refrigerants may also cause harm to the environment if

released to the atmosphere.

If you are throwing away your old

refrigerator, make sure the refrigerant is removed for proper disposal by a qualified

technician. If you intentionally release

refrigerant, you may be subject to fines and imprisonment under provisions of environmental legislation.

If the power cord is damaged, it should

be replaced by an authorized service

technician to prevent any risk.

Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to

prevent damaging the power cord.

Unplug the refrigerator before cleaning and before replacing a light bulb to avoid

electrical shock.

Performance may be affected if the voltage varies by 10% or more. Operating the

refrigerator with insufficient power can damage the compressor. Such damage is

not covered under your warranty.

Do not plug the unit into an electrical outlet controlled by a wall switch or pull cord to

prevent the refrigerator from being turned off accidentally.

Pressing and holding the On/Off button for three seconds, located on the temperature control panel, will disable your refrigerator's

refrigerator you must unplug the power cord from the electrical outlet.

Grounding type wall receptacle

Do not, under any circumstances, cut, remove, or bypass the

grounding prong,

Electrical information

• The refrigerator must be plugged into its own dedicated 115 Volt, 60 Hz., 15 Amp,

AC only electrical outlet. The power cord of the appliance is equipped with a three-

prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded

three prong receptacle. The receptacle

must be installed in accordance with local codes and ordinances. Consult a qualified

electrician. Avoid connecting refrigerator to a Ground Fault Interrupter (GFI) circuit. Do not use an extension cord or adapter plug.

To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden

*Can Rack

Flip Shelf-

*LED Cluster-=

Light

*Store-

MoreTM--

Drawer

Adjustable Hinges

*Features may vary according to model

*LED *Dairy

*Freezer Ice

Maker

Removable /

Ice Bin

Compartment *Air

Filter

-_ Mullion

-_ *LED Cluster

-_-*LED Cluster

=+___i Crisper

-+---*Door Bin

Freezer Baskets

Toe Grille

Flipper

//Spillsafe

Shelves

Light

Slide-Under

Shelf

Light

Drawer

Features not purchased with your refrigerator can be purchased at www.frigidaire.com or by calling 1-800-944-9044.

Tools Necessary:

) N&

#2 Square wrSeOC_et£t Wrench , f_,'

DriveHead _

AND __ OR OR

Adjustable

compo.e.tSp,ov aoa:

Top Hinge Top Hinge Cover Front Cover Rear Screw Screw

)

This Use & Care Guide provides general installation and operating instructions for your model. We recommend using a service or kitchen contracting professional to install your refrigerator. Use the refrigerator only as

instructed in this Use & Care Guide. Before starting the refrigerator, follow these

important first steps.

Location

Choose a place that is near a grounded, non-GFC[, electrical outlet. Do Not use an extension cord or an adapter plug.

If possible, place the refrigerator out of direct sunlight and away from the range,

dishwasher, or other heat sources.

The refrigerator must be installed on a floor that is level and strong enough to support

a fully loaded refrigerator. Consider water supply availability for

models equipped with an automatic ice maker.

Do Not install the refrigerator where the

temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor

will not be able to maintain proper temperatures inside the refrigerator.

Do Not block the toe grille on the lower front of your refrigerator. Suffldent air circulation

refrigerator,isessential for the proper operation of your

Installation

Allow the following clearances for ease of installation, proper air circulation, and

plumbing and electrical connections:

Sides & Top 3/8inch (9.5 mm)

Back 1 inch (25.4 mm)

If your refrigerator is placed with the door hinge side against a wall, you may have to

allow additional space so the door can be opened wider.

Door opening

Your refrigerator should be positioned to allow easy access to a counter when removing food. For best use of refrigerator drawers and freezer baskets, the refrigerator should be in a

position where both can be fully opened.

Leveling Freezer Drawer (if necessary)

To level the freezer drawer:

1 Check gasket seal around top, bottom, and sides of freezer drawer. 2 If gasket is not sealed, open drawer and slightly loosen four drawer screws (two on each

side) to allow drawer to pivot.

Loosen Hex Head

Drawer Screw

Loosen Hex Head Drawer

Screw

3 Close drawer and recheck the seal on the

gasket (A). Open the drawer grabbing by the sides in the center (B). Be careful not

to rotate the drawer.

Grab

Against Freezer

Drawer

at Center

from Both

Sides

Then

Pul!

Drawer

Out

Loosen HexHead

Drawer Screw

LoosenHex

HeadDrawer

Screw

Doors should align with each other and be level.

Most of these conditions can be met by

raising or lowering the adjustable front rollers.

To level the cabinet using the front

rollers:

Toeq J

Fit in Slot on

Anti4ip Bracket

Screw/Washer

Assembly

4 Tighten four drawer screws.

5 Recheck gasket seal.

Level Refrigerator & Adjust Doors (if necessary)

Guidelines for final positioning of your refrigerator:

All four corners of the cabinet must rest firmly on the floor,

The sides should tilt 1/4inch (6 mm) from front to back (to ensure that doors close

and seal properly).

Retai_in(

1 Slightly open freezer drawer. Lift the

toe grille and gently pull forward (see

illustration). Toe grilles vary by model.

2 You can raise or lower each door. Use

a 3/8inch socket wrench to turn the adjustment screws (one per side).

To raise: turn adjustment screw clockwise. To lower: turn adjustment screw

counterclockwise.

3 Ensure both doors are bind-free with their

seals touching the cabinet on all four sides and that cabinet is stable.

4 Afterunitisleveled,loweranti-tipleguntil

itcontactsthefloor.

,_j........ )c......... :

_Raise

5 Install the toe grille by fitting into place.

To adjust the door stop:

Door stop is adjustable between 85 to 145 degrees.

1 Open door to provide access to screw. 2 Loosen screw.

3 Adjust door to desired location.

Adjusting Door

Rotate door stop until it makes contact

with the lower hinge.

Re-tighten screw.

i View shown is looking up at the bottom of

the refrigerator door.

\.. Door

screw

Adjustable Door Stop

_________:_:_:_:_

Re-tighten

Screw

Re-tighten Screw

Ensure door stops in desired location before resuming normal use.

To level the doors using the adjustable lower hinge (select models):

1 Remove all food items from door bins on

door being adjusted.

2 Open doors to 90 degrees.

3 Loosen or remove screw.

LoOsen OrRemove

Screw 1

....._7 ...................._77

Bottom of Door

Loosen/Remove Screw (where applicable)

To adjust the flipper mullion:

1 Loosen the screw located on the flipper

mullion hinge.

)eF

Mullion

Fli

Hinge

Adjusting Flipper Mullion Screw

Adjust flipper mullion height. For proper connection with the flipper mullion guide, there should be a separation about the thickness of a coin (0.060 inches, or

1.5 mm) between the guide and flipper mullion.

Adjustable hinge should only be used after doors have been leveled with rollers.

4 Lift the door while adjusting the washer,

To raise the door, rotate washer clockwise

(when viewed from the bottom). To lower door, rotate washer counter-clockwise

(when viewed from the bottom).

Fti

Mullion

ide

Thickness

of a Coin

Adjusting Flipper Mullion Height

3 Re-tighten screw.

Raising/Lowering Door

_!!!!Biiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii;__

Getting through narrow spaces

If your refrigerator will not fit through an entrance area, you can remove the doors. Check first by measuring the entrance.

To prepare for removing the doors:

1 Make sure the electrical power cord is

unplugged from the wall outlet.

2 Open the freezer drawer and remove the

toe grille (see "Installation" section).

3 Remove any food from the door shelves

and close the doors.

To remove the top hinge covers:

1 Remove the two screws from each cover

over the top door hinges.

2 Lift inside edge of hinge cover and tilt

back.

Cover €

Top,_.,Hinge _ Sc[ew

Hinge Ground

MUlti.wire

Hinge

To remove the refrigerator doors:

1 Trace lightly around the door's top hinges

with a pencil. This makes reinstallation easier.

Disconnect the harness by grasping both

sides of the connector firmly, depress the

latch, and pull apart. Remove the two screws from the top hinge. Lift the door off of the bottom hinge and set it aside.

Hing ,, Water Door Line

.. Front

_ear ,, Cover Screw

L,over_ A 7

Screw /_'

¢_>_-_ _ _Top Hinge

_r,_ .q.j_ Cover

Hinge

Hinge scr, ewi I Screws

"-L "---<\ Two w re

"-.L Cab!es

1,"_ _v,_ Leave

"N_; _" -... _ "% Hinge

_i_ _/With

Door

DO NOT remove the ground screw from hinge.

Detach the water tube from the connector

located behind the refrigerator and pull the tube back out to the front of the unit.

The connector releases when you press

inward on the outer sleeve while pushing the tube toward the connector then while

continuing to hold in the sleeve, pull the tube away.

Use care while pulling the water tube from the unit to be sure that you do not kink the

tube.

feet

You will be pulling approximately five feet of water tube from the back of the refrigerator.

4 Unscrew the three lower hinge screws and

hinge if necessary.

To reinstall the right door, reverse the above steps.

Lower Hinge Removal

Once both doors are in place, ensure they are aligned with each other and level (Please see the "Installation" section for more details), and replace the top hinge cover.

When reinserting the water tube and

replacing the top hinge cover, use care to be

sure you do not kink the tube.

Be sure doors are set aside in a secure position where they cannot fall and cause

personal injury, or damage to the doors or handles.

Removing Freezer Drawer

1 Open freezer drawer.

2 Remove drawer screws on right and left sides (two screws on each side).

Loosen Hex Head Loosen Hex Head

Drawer Screw Drawer Screw

Loosen Hex Head Drawer

Screw

i; ii ii

Do not remove center screw from freezer Drawer is heavy. Use caution when lifting.

drawer. This is a factory adjustment. ............

Installing Freezer Drawer

1 With lower slides pulled out, hang drawer

onto slide brackets ensuring pins on each side are fully inserted into slots on each side.

issem_y Fully Extend t_) _ Drawer Slides

3 Lift drawer up and out to remove.

Check gasket seal around top, bottom, and sides of freezer drawer.

If gasket is not sealed, open drawer and slightly loosen four drawer screws (two on each side) to allow drawer to rotate.

Close drawer and recheck the seal on the gasket (A). Open the drawer grabbing by

the sides in the center (B). Be careful not to rotate the drawer.

Loosen Hex

Head Drawer

Drawer

_inO II p_ Cabinet

at Center

from Both

_ Sides

Reinstall four drawer screws (two per side), tighten down, and close drawer.

Drawer

Screw

Grab

Then

Pull

Out

Side

6 Tighten four drawer screws. 7 Recheck gasket seal. 8 To installtoe grille,openfreezer drawer, lifttoe

gnlleand fit into place.Toe gnllesvary by model.

Door Handle Mounting Instructions for Frigidaire

1 Remove handles from carton

and any other protective packaging.

2 Position fresh food handle

end caps over upper and lower pre-installed shoulder bolts (A) that are fastened into door, ensuring the holes for the set screws are facing towards the opposite door.

3 While holding handle firmly

against door, fasten upper and lower Allen set screws (13)with supplied Allen wrench.

4 Repeat steps 2 and 3 to

install opposite handle. Ensure the holes for the set

screws are facing towards the first door.

5 Position freezer handle end

caps over left and right pre-installed shoulder bolts that are fastened to the door, ensuring the holes for the set screws are facing down.

6 While holding handle firmly

against door, loosely tighten right Allen set screw (B) with supplied Allen wrench until there is no gap between

handle and door.

7 Still holding the handle firmly

to the door, firmly tighten left Allen set screw (B) with supplied Allen wrench.

8 Return to the right Allen set

screw (B) and firmly tighten with supplied Allen wrench.

Mounting Refrigerator Handles

Mounting Freezer Handle

All set screws should be tightened so the screw is below the surface of the handle. The

handles should be drawn tight to freezer and refrigerator doors with no gaps. Opening the

opposite door while tightening the Allen screw makes installation easier. The door handle may loosen over time or if it was installed improperly. If this happens,

Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.

Door Handle Hounting

Instructions for Frigidaire Gallery ®

1 Remove handles from carton

and any other protective packaging.

2 Position fresh food handle

end over upper and lower preqnstalled shoulder bolts (A) that are fastened into door, ensuring the holes for the set screws are facing towards the opposite door.

3 While holding handle firmly

against door, fasten upper and lower Allen set screws (13)with supplied Allen wrench.

4 Repeat steps 2 and 3 to install

opposite handle. Ensure the holes for the set screws are

facing towards the first door.

5 Position freezer handle end

over left and right pre- installed handle mounts that

are fastened to the door, ensuring the holes for the set screws are facing down.

6 While holding handle firmly

against door, loosely tighten far right Allen set screw (B) with supplied Allen wrench until there is no gap between

handle and door.

7 Still holding the handle firmly

to the door, firmly tighten far left Allen set screw (B) with supplied Allen wrench.

8 Return to the far right Allen set

screw (B) and firmly tighten with supplied Allen wrench.

Mounting Refrigerator Handles

Mounting Freezer Handle

All set screws should be tightened so the screw is below the surface of the handle. The

handles should be drawn tight to freezer and refrigerator doors with no gaps. Opening the

opposite door while tightening the Allen screw makes installation easier. The door handle may loosen over time or if it was installed improperly. If this happens,

screws on the hand!es_ ......................................................................................................................................................................................................................

Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.

Door Handle Mounting Instructions for

Frigidaire Professional ®

1 Remove handles from carton

and any other protective packaging.

2 Positbn fresh food handle end

over upper and lower pre- installed shoulder bolts (A) that are fastened into door, ensuring

the holes for the set screws are facing towards the opposite door.

3 While holding handle firmly

against door, fasten upper and lower Allen set screws (B) with supplied Allen wrench.

4 Repeat steps 2 and 3 to install

opposite handle. Ensure the holes for the set screws are

facing towards the first door.

5 Position freezer handle end

over left and right pre-installed handle mounts that are

fastened to the door, ensuring the holes for the set screws

are facing down.

6 While holding handle firmly

against door, loosely tighten far right Allen set screw (B) with supplied Allen wrench until there is no gap between

handle and door.

7 Still holding the handle firmly

to the door, firmly tighten far left Allen set screw (B) with supplied Allen wrench.

8 Return to the far right Allen set

screw (B) and firmly tighten with supplied Allen wrench.

9 Firmly tighten the inside Allen

set screws.

Mounting Refrigerator Handles

All set screws should be tightened so the screw is below the surface of the handle. The

handles should be drawn tight to freezer and refrigerator doors with no gaps. Opening the

opposite door while tightening the Allen screw makes installation easier. The door handle may loosen over time or if it was installed improperly. If this happens,

Wear gloves and safety goggles. Use extreme CAUTION when installingthese handles.

+ 30 hidden pages