Frigidaire FNDP15W1, FNDP15B1 Owner’s Manual

Installation hardware kits located inside pedestal:

Vous trouverez le n_cessaire de quincaillerie d'installation _ I'int_-

rieur du socle :

Los accesorios del kit de instala- ci6n est_n ubicados en el interior del pedestal:

Tools needed: Outils necessaires:

Herramientas necesarias:

GREEN KIT COMPONENTS:

A 2 Front brackets. B 2 Front bracket spacers.

C 2 Rear brackets.

COMPOSANTS DU N[eCESS.VERT:

A 2 supports avant. B 2 espaceurs pour supports avant. C 2 supports arriere.

PIEZAS DEL KIT VERDE: C; __

A 2 soportes delanteros. B 2 espaciadores para soportes delanteros. C 2 soportes traseros.

WHITE KIT COMPONENTS: ___

D 1 Left Front bracket. D

E 1 Right Front bracket.

F 2 Rear brackets.

COMPOSANTSDU NI_CESS.BLANC" E _._J

D 1 support avantgauche.

E 1 support avant droit.

F 2 supports arriere.

PIEZAS DEL KIT BLANCO:

D 1 soporte delantero izquierdo.

E 1 soporte delantero derecho.

F 2 soportes traseros.

SCREW KIT COMPONENTS:

o 14 #10 (16 x .500) screws.

COMPOSANTS DU Ni_CESSAIREDEVlS:

14vis n° 10 (16 x .500).

PIEZAS DEL KIT (TORNILLOS):

14 tornillos n.° 10 (16 x .500).

OR OU

Optional universal Adjustable wrench 9/16" or 14 mm box wrench

wrench available

from dealer Cle 9.molette Cle polygonale de

Cle universelle Llave ajustable

optionnelle (en vente Llave de cubo de

chez le detaillant) 9/16 po o 14 mm

Llave universal opcional

(disponible a trav6s

de su distribuidor local)

Failureto disconnect from power source before stacking could result in personal

injury or even death. Improper installation of dryer venting

could result in personal injury or damage

to property. Toavoid back or other injury, have more

than one person move or lift the washer

or dryer.

OR OU

9/16 po ou de 14 mm

Ne pas d_brancher I'appareil de sa source d'alimentation en _lectricite avant de le

superposer peut causer des blessures,

voire la mort.

Une installation inappropri@ du systeme de ventilation de la secheuse peut causer des blessures ou des dommages materiels. Pour _viter les blessures au dos ou

d'autres types de blessure, demandez I'aide d'autres personnes pour d_placer

ou soulever la laveuse ou la secheuse.

English continued on page 2.

Pour la suite de la version fran_aise,

reportez-vous a la page 6.

AND

Phillips screwdriver

Tburnevis Phillips

Destornillador Phillips

Carpenter's level

Niveau de charpentier

Nivel de carpintero

El no desconectar el suministro electrico antes de la instalaciOn apilada puede

ocasionar lesiones personales o incluso la muerte.

La instalaciOn inadecuada de la ventilaciOn de la secadora puede ocasionar lesiones

personales o dahos a la propiedad. Para evitar lesiones en la espalda u otro

tipo de lesiones, procure levantar o mover la lavadora o secadora con la ayuda de mas de una persona.

Laversion en espanolcontinOaen la p_igina10.

137147600 A (0901)

PREPARATION iNSTRUCTiONS

Due to higher center of gravity of appliance on ped-

estals, some side-to-side rocking is normal during operation. Vibration can be minimized by assuring appliance is installed

properly, including being level and solid on all four (4) legs by following these directions.

A) Preparing washer or dryer for mount-

ing on pedestal

1. If washer or dryer is new and has not been installed yet, skip to step 4.

2. If dryer is already installed, disconnect dryer from electrical and gas connections and exhaust venting.

If washer is already installed, disconnect washer from electrical

connection. Turn off hot and cold water supply and disconnect

hot and cold water supply hoses from water supply outlets. Disconnect drain hose from drain pipe.

4. If appliance has plastic feet, screw each foot flush to the base.

5. If appliance has metal feet, unscrew them, remove the locking

nut and reinstall the feet flush to the base.

2. Level the pedestal front-to-back and side-to-side by adjusting each leveling leg. Keep leg extension to a minimum.

Optional universal wrench (or adjustable pliers).

If locking nuts are not removed on units with metal

feet, mounting holes in appliance will not align to mounting holes in brackets.

B) Preparing pedestal before mounting

washer or dryer

1. Locate pedestal to within a few inches of its final location.

DO NOT remove foal'

Allow for approximately 5 in. (12.5 cm) behind the pedestal for clearance of back of washer or dryer to the wall. Allow additional space if venting dryer upward or downward.

3. Rock the pedestal from comer-to-comer to check for stability. Repeat leveling and rocking until all four (4) feet are sturdy on the

floor and pedestal is level.

4. Without turning the rubber foot, lock each pedestal leg in place by tightening its lock nut tight against the pedestal base.

lock nut

3.5 cu ft WASHER INSTRUCTIONS (GREEN KIT)

C1) Attaching washer mounting hardware

1. Use the following instructions for mounting either of these types of washers to the pedestal:

2. Attach each front clip to outer-most set of holes with 2 screws and supplied spacer.

Locate spacer under each front bracket.

® ®

DI) Mounting washer

- EXCESSIVE WEIGHT HAZARD - To avoid

back or other injury, have more than one person move or lift the washer.

Using two or more persons, slightly tip the washer back and lift it

onto the pedestal. Still tipped, slide the washer back against the

rear brackets and gently set down the front so the appliance is between the front and rear brackets.

Adjust the appliance side-to-side to align its mounting holeswith the pedestal's bracket holes.

Install 2 screws through each rear bracket into the base of the

washer.

m m

Z X

-q

3. Insert "A" tab of each rear bracket into the middle slots on rear of pedestal. Orient bracket inward for washer mounting.

"A" :I_,'_F_

tab_ _ middle

__ slot

Install 2 screws through each rear bracket into aligning pedestal holes.

.\ _b inward

4. Install a screw through each front bracket into the base of the washer.

E_)Installing or re-installing washer

1. Slide appliance/pedestal into place.

2. Check for levelness and rock all four (4) legs again. Repeat until

level and solid.

3. Refer to Washer Installation Instructions for complete details on installing water, drain, or electrical.

m m

-q

m m

-q

m m

-q

7.0 CUft DRYER (STYLE 1)iNSTRUCTiONS (GREEN KiT)

C2) Attaching dryer (style 1) mounting

hardware

Use the following instructions for mounting any of these types of

dryers to the pedestal:

Dryer cabinet (style 1) with 3 indents on side.

W W

2. Attach each front clip to outer-most set of holes with 2 screws.

NO spacers under front brackets.

D2) Mounting dryer (style 1)

- EXCESSIVE WEIGHT HAZARD - To avoid

back or other injury, have more than one person move or lift the dryer.

Using two or more persons, slightly tip the dryer back and lift it

onto the pedestal. Still tipped, slide the dryer back against the

rear brackets and gently set down the front so the appliance is between the front and rear brackets.

Adjust the appliance side-to-side to align its mounting holes with the pedestal's bracket holes.

Install 2 screws through each rear bracket into the base of the

dryer.

3. Insert "A" tab of each rear bracket into the rear slots on rear of pedestal using rearbracket spacers. Orient bracket inward for

_ tab _'_ -. _nward

O _-_slot \'\.\.

"style 1" dryer mounting.

rear _

4. Install 2 screws through each rear bracket into aligning pedestal holes.

i ' i '

i '

nsta a screw tnrougn eacr front DracKet nto tne Dase of me

oryer.

E2)Installing or re-installing dryer (style 1)

1. Slide appliance/pedestal into place.

2. Check for levelness and rock all four (4)legs again. Repeat until level and solid.

3. Refer to Dryer Installation Instructions for complete details on installing electrical, gas, or exhaust venting.

5.8 CUft DRYER (STYLE 2)INSTRUCTIONS (GREEN KIT)

Cs) Attaching dryer (style 2) mounting

hardware

Use the following instructions for mounting any of these types of

dryers to the pedestal:

Dw_Yhr2canbd::tts(Sty'e'd)e [/_1 II_[ and 4 inchknockout for IN1 INI

side vent_g. I lil

2. Attach each front clip to outer-most set of holes with 2 screws.

D3) Mounting dryer (style 2)

- EXCESSIVE WEIGHT HAZARD - To avoid

back or other injury, have more than one person move or lift the dryer.

Using two or more persons, slightly tip the dryer back and lift it

onto the pedestal. Still tipped, slide the dryer back against the

rear brackets so tabs on rear brackets engage the slots on the back of the dryer. Gently set down the front so the appliance is between the front and rear brackets.

ENGAGE REAR TABS

m m

IT1

-q

NO spacers under front brackets.

3. Insert "B" tab of each rear bracket into the front slots on rear of pedestal. Orient bracket outward for "style 2" dryer mounting.

aBb---_ front

\.\ slot

_:_b outward

4. Install 2 screws through each rear bracket into aligning pedestal holes.

[ ;;

Adjust the appliance side-to-side to align its mounting holes with the pedestal's bracket holes.

Install a screw through each front bracket into the base of the

dryer.

/ TiP DOWN

Es) Installing or re-installing dryer (style 2)

1. Slide appliance/pedestal into place.

2. Check for levelness and rock all four (4)legs again. Repeat until level and solid.

3. Refer to Dryer Installation Instructions for complete details on installing electrical, gas, or exhaust venting.

m m

-q

m m

-q

m m

-q

C4) Attaching washer mounting hardware

1. Use the following instructions for mounting this type of washer to the pedestal:

"I"

Remove 2 screws from service access

below front panel.

Remove lower service accesspanel.

Remove 2 lower screws from backsheet of washer. Save screws to reinstall later.

D4) Mounting washer

- EXCESSIVE WEIGHT HAZARD - To avoid

back or other injury, have more than one person move or lift the washer.

Using two or more persons, slightly tip the washer back and lift it

onto the pedestal. Still tipped, slide the washer back against the

rear brackets and gently set down the front so the appliance is between the front and rear brackets.

i,_

Remove 2 screws from

washer backsheet.

4. Attach each front clip to outer-most set of holes with 2 screws.

"I"

5. Insert "A" tab of each rear bracket into the middle slots on rear of pedestal. Orient bracket outward for washer mounting.

"A"'_J _'°_°' middle

"[ ..... J

outward

Adjust the appliance side-to-side to align its mounting holeswith the pedestal's bracket holes.

Reinstall backsheet screws removed earlier through each rear bracket into the base of the washer.

i iil

4. Reinstall the lower service accesspanel.

5. Reinstall the 2 screws removed earlier through the outer hole of each front bracket into the base of the washer.

tab _slot._

6. Install 2 screws through each rear bracket into aligning pedestal

holes.

E4)Installing or re-installing washer

1. Slide appliance/pedestal into place.

2. Check for levelness and rock all four (4) legs again. Repeat until

level and solid.

3. Refer to Washer Installation Instructions for complete details on installing water, drain, or electrical.

+ 14 hidden pages