Frigidaire FMB330RG, FMB330RGC, FMB330RGB, FMB330RGS, FMP330RG Installation Instructions Manual
...
Installation
Built-In
Instructions
Dishwasher
If you have questions, call 800-944-9400(US),800-245-8352(Canada)or visit
our website at: www.Frigidaire.com
BEFORE YOU BEGIN
Read these instructions
completely and carefully.
IMPORTANT – Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave
these instructions for the
consumer's and local inspector's
use.
• Note to Consumer – Keep these
instructions with your Owner’s
Manual for future reference.
• Skill Level – Installation of this
dishwasher requires basic mechanical
and electrical skills. Proper
installation is the responsibility
of the installer. Product failure
due to improper installation is not
covered under the ELECTROLUX
Appliance Warranty.
• Completion Time – 1 to 3 Hours. New
installations require more time than
replacement installations.
IMPORTANT – The dishwasher
MUST be installed to allow for future
removal from the enclosure if service
is required.
If you received a damaged dishwasher,
you should immediately contact your
dealer or builder.
Optional Accessories – See the Owner’s
Manual for available custom panel
kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and
WARNINGS shown throughout these
instructions. While performing
installations described in this
booklet, gloves, safety glasses or
goggles should be worn.
WARNING
To reduce the risk of electrical shock, fire, or
injury to persons, the installer must ensure that
the dishwasher is completely enclosed at the
time of installation.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Preparation
PARTS SUPPLIED:
¨ Two #8 Phillips flat head wood screws, 5/8” long to secure
dishwasher to underside of countertop (in literature package).
¨ Two Phillips head, color matched toekick screws (in literature
package).
MATERIALS YOU WILL NEED:
¨ Ferrule, compression nut and 90° Elbow (3/8”NPT external
thread on one end, opposite end sized to fit water supply)
¨ Thread seal tape
¨ UL Listed wire nuts (3)
Materials for New
Installations Only:
¨ Air gap for drain hose, if required
¨ Waste tee for house plumbing, if applicable
¨ Electrical cable or power cord, if applicable
¨ Screw type hose clamps
¨ Strain relief for electrical connection
¨ Hand shut-off valve
¨ Water line 3/8” min. copper
¨ Coupler for extending drain line, if applicable
2 Wood Screws
90° Elbow, Ferrule
and Compression Nut
Waste Tee
Screw Type
Air Gap
Hose Clamps
2 Color Matched
Toekick Screws
Hand ShutOff Valve
Electrical Cable
(or Power Cord, if applicable)
Thread
Seal Tape
Strain Relief
Screw Type
Hose Clamp
Wire Nuts (3)
Hot Water line
Coupler
TOOLS YOU WILL NEED:
Phillips head screwdriver
5/16" and 1/4" nutdriver
6" Adjustable wrench
Level
Carpenters square
Measuring tape
Safety glasses
Flashlight
Bucket to catch water when flushing the line
Gloves
For New Installations
Only:
Tubing cutter
Drill and appropriate bits
Hole saw set
Phillips Head
Screwdriver
Flashlight
Gloves
Bucket
2
1/4"
and 5/16"
Nutdriver
Safety Glasses
Hole Saw Set
6" Adjustable
Wrench
Level
Carpenters
Square
Tubing Cutter
Measuring Tape
Drill and Bits
Installation Preparation
Must Enter Shaded Area
Clearance for Door
Opening 2" Minimum
Countertop
Dishwasher
25-5/8"
PREPARE DISHWASHER ENCLOSURE
32.5"
Underside of
Countertop
to Floor
17-5/8" Min.
18" Max.
Figure A
Plumbing and Electric Service
• The rough cabinet opening must be at least 24” deep and
17-5/8” to 18” wide. The opening should be 32.5” max. height.
24"
Min.
4"
Cabinets
Square
6"
and
Plumb
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Do not exceed 10 feet distance to drain.
• Do not connect drain lines from other devices to the
dishwasher drain hose.
• Dishwasher must be connected to waste line with an air gap
(not supplied) or 32" minimum high drain loop, depending on
local codes and ordinances to prevent back flow into the
dishwasher.
• Air gap must be used if waste tee or disposer connection is
less than 18" above the floor to prevent siphoning.
DRAIN PREPARATION
The type of drain installation depends on answers to the
following questions:
Do local codes or ordinances require an air gap?
Will waste tee or disposer connection be less than 18"
above the floor?
Will installation have a drain loop less than 32" above floor?
If the answer to ANY of the 3 questions above is YES,
Method 1 MUST be used. Otherwise either Method 1 or
Method 2 may be used. Figure C or Figure D.
• The dishwasher must be installed so that drain hose is no more
than 10 feet in length for proper drainage.
• The dishwasher must be fully enclosed on the top, sides and
back, and must not support any part of the enclosure.
CLEARANCES:
installed into a corner,
allow 2” min. clearance
between dishwasher and
adjacent cabinet, wall or
other appliances. Allow
25-5/8" min. clearance
from the front of the
dishwasher for door
opening. Figure B
Note: ADA installation, (32-1/2”) beneath 34” high counter-tops may be
accomplished by adjusting the toekick and leveling legs.
When
Figure B
Method 1 – Air Gap with Waste Tee or
Disposer
Figure C
Method 2 – High Drain with Waste Tee
or Disposer
Provide a method to attach drain hose to underside of countertop.
32"
18"
Min.
32"
Min.
Min.
18"
Min.
CAUTION:
An air gap MUST BE USED if the drain hose is connected to
waste tee or disposer lower than 18" above the floor.
Failure to provide the proper drain connection height with air gap
or 32" minimum, high drain loop will result in improper draining
of the dishwasher.
Figure D
Install waste tee or disposer and air gap according to
manufacturer’s instructions.
CABINET PREPARATION
• Drill a 1-1/2” dia. hole in the cabinet wall within the shaded
areas shown in Figure A for the drain hose connection. The hole
should be smooth with no sharp edges.
3
Installation Preparation
White
t
PREPARE ELECTRICAL WIRING
WARNING
FOR PERSONAL SAFETY: Remove house fuse
or open circuit breaker before beginning
installation. Do not use an extension cord or
adapter plug with this appliance.
1-1/2" Dia.
Hole (Max.)
Electrical Requirements
• This appliance must be supplied with 120V, 60 Hz., and
connected to an individual properly grounded branch circuit,
protected by a 15 or 20 ampere circuit breaker or time delay
fuse.
• Wiring must be 2 wire with ground.
• If the electrical supply does not meet the above requirements,
call a licensed electrician before proceeding.
Grounding Instructions – Cable Direct
This appliance must be connected to a grounded metal, permanent
wiring system, or an equipment grounding conductor must be run
with the circuit conductors and be connected to the equipment
grounding terminal or lead on the appliance.
Grounding Instructions – Power Cord
Models
his appliance must be grounded. In the event of a malfunction or
breakdown, grounding will reduce the risk of electrical shock by
providing a path of least resistance for electric current. The plug
must be plugged into an appropriate outlet that is installed and
grounded in accordance with local codes and ordinances.
WARNING
The improper connection of the equipment
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service representative if you
are in doubt that the appliance is properly
grounded.
3"
from
Cabine
24"
from Wall
Ground
Figure E
Cabinet Preparation & Wire Routing
• The wiring may enter the opening from either side, rear or the
floor within the shaded area.
• Cut a 1-1/2” max. dia. hole to admit the electrical cable. The hole
must be free of sharp edges. If the cabinet wall is metal, the
hole edge must be covered with a bushing.
• Cable direct connections may pass through the same hole as the
drain hose and hot water line, if convenient. If cabinet wall is
metal, the hole edge must be covered with a bushing.
NOTE: Power cords with plug must pass through a separate
hole.
Electrical Connection to Dishwasher
Electrical connection is on the right front of dishwasher.
• For cable direct connections the cable must be routed as shown
in Figure E. Cable must extend a minimum of 24” from the rear
wall.
• For power cord connections, install a 3-prong grounding type
receptacle. The power-supply receptacle for the appliance shall
be installed in a cabinet or on a wall adjacent to the
undercounter space in which the appliance is to be installed.
Black
4
Installation Instructions
C
PREPARE HOT WATER LINE
• The line may enter from either side, rear or floor within the
shaded area shown in Figure F.
• The line may pass through the same hole as the electrical
cable and drain hose. Or, cut an additional 1-1/2” dia. hole to
accommodate the water line.
If power cord with plug is used, water line must not pass
through power cord hole.
Valve
4"
1-1/2" Dia.
Hole
18" From Wall
3" From Floor
Shut-off
Hot
From
Cabinet
abinet Face
Figure F
BEFORE YOU BEGIN
Locate and set aside the package containing
2 Phillips head countertop mounting screws and
2 additional toekick screws (located in the literature
package).
STEP 1 CHECK DOOR BALANCE
To check the door balance, hold the top of the dishwasher
firmly.
Increase
Decrease
Water Line Connection
• Turn off the water supply.
• Install a hand shut-off valve in an accessible location, such as
under the sink. (Optional, but strongly recommended and may
be required by local codes.)
• Water connection is on the left side of the dishwasher. Install
the hot water inlet line, using no less than 3/8” O.D. copper
tubing. Route the line as shown in Figure F and extend
forward at least 18” from rear wall.
• Adjust water heater for 120°F to 150°F temperature.
• Flush water line to clean out debris.
• The hot water supply line pressure must be 20-120 PSI.
CAUTION:
Opening the door will cause the dishwasher
to tip forward.
ready to install the dishwasherready to install the dishwasher
ready to install the dishwasher
ready to install the dishwasherready to install the dishwasher
it is necessary to open the door, hold
the top of the dishwasher securely with
one hand and hold the door with the
other hand.
Do not open the door until you areDo not open the door until you are
Do not open the door until you are
Do not open the door until you areDo not open the door until you are
. If. If
. If
. If. If
Figure G
• Open the door slowly, if the door drops when released,
increase spring tension. If the door closes when released,
decrease tension.
• Pull the spring adjustment pin out of the holes, insert in the
next highest or lowest hole and test again.
• Adjust both door springs to the same tension.
• Continue moving the spring pin until door is balanced.
5
Installation Instructions
I
E
ll
se
Seal Tape
r
t
STEP 2 ADJUST LEVELING LEGS
• Move the dishwasher close to the installation location and lay
it on its back.
Adjust to
nstallation
Height
Figure H
• Measure installation height and dishwasher height. Extend
leveling legs out from the dishwasher base, 1/4" less than
installation height.
STEP 3 REMOVE TOEKICK
STEP 4 INSTALL 90° ELBOW
• Wrap 90° elbow with thread seal tape.
• Install a 90° elbow onto the water valve.
Fi
Ho
90°
lbow
Wate
Valve
Bracke
Thread
Figure L
• Do not over tighten 90° elbow, water valve bracket could
bend or water valve fitting could break.
• Position the end of the elbow to face the rear of the
dishwasher.
• Remove the 4 toekick screws. Lift off the 2 piece toekick.
Remove
4 Toekick
Screws
Figure J
6
I
Installation Instructions
Do Not Push Against
Front Door Panel With
Knee. Damage to The
Door Panel Will Occur.
STEP 5 POSITION WATER LINE
AND HOUSE WIRING
• Position water supply line and house wiring on the floor of
the opening to avoid interference with base of dishwasher
and components under dishwasher.
4"
6"
Water
Line
Figure M
House
Wiring
STEP 6 INSERT DRAIN HOSE
THROUGH CABINET
• Insert drain hose into cabinet wall hole. If a power cord is
used, guide the end through a separate hole.
STEP 7SLIDE DISHWASHER
PARTIALLY INTO CABINET
DO NOT PUSH AGAINST FRONT PANEL WITH
KNEES. DAMAGE WILL OCCUR.
• Slide dishwasher into the opening a few inches at a time.
Figure O
• As you proceed, pull the drain hose through the opening
under the sink. Stop pushing when the dishwasher is a few
inches forward of adjacent cabinetry.
• Make sure drain hose is not kinked under the dishwasher
and there is no interference with the water line and wiring
or any other component.
Maximum
Drain Hose
Length 10'
nsulation
Blanket
Figure N
TIP: Position water line and house wiring on the floor to avoid
interference with base of dishwasher.
Water
Line
Drain
Hose
House
Wiring
Power Cord
(If Used)
7
Do Not Push Against
Front Door Panel With
Knee. Damage to The
Door Panel Will Occur.
Reposition Dishwasher
by Grasping Both
Sides With Hands
Installation Instructions
k
l
e
de
t
STEP 8 POSITION DISHWASHER UNDER COUNTERTOP
• Check to be sure that wires are secure under the dishwasher
and not pinched or in contact with door springs or other
dishwasher components.
TIP: Check tub insulation blanket, if equipped. It should be
positioned so it is not bunched up or interfering with door
springs. Check by opening and closing the door.
• Push dishwasher into cabinet. The front corners of the
dishwasher door should be flush with cabinet doors. Be
careful not to dent front panels with knees or damage
countertop or cabinets with dishwasher parts.
Figure P
STEP 9 LEVEL DISHWASHER
IMPORTANT – Dishwasher must be
level for proper dish rack operation and wash performance.
• Place level on door
and rack track inside
the tub as shown to
check that the
dishwasher is level.
Check
Level
Front
o Back
Figure Q
Chec
Leve
Sid
To Si
• Level the dishwasher by
adjusting the four leveling
legs individually.
Turn Legs
to Adjust
Figure R
TIP: Pull lower rack out, about halfway. Check to be sure the rack
does not roll forward or back into dishwasher. If the rack rolls in
either direction, the dishwasher must be leveled again.
• If door hits the tub, the dishwasher is not installed correctly.
Adjust leveling legs to align door to tub.
8
Installation Instructions
b
t
t
STEP 10SECURE DISHWASHER
TO CABINET
The dishwasher must be secured to the countertop.
• Position the dishwasher so that the tub flange aligns with the
front face of the cabinet frame.
IMPORTANT: Check to be sure the dishwasher is
centered in the opening and there is no interference with
adjacent cabinets when opening or closing the door.
Align Tu
Flange
to Fro n
Face of
Cab ine
Fra me
Figure S
• Fasten the dishwasher to the underside of the countertop
with the 2 Phillips screws provided.
STEP 11 CONNECT WATER
SUPPLY
Connect water supply to 90° elbow.
• Slide compression nut, then ferrule over end of water line.
• Insert water line into 90° elbow.
• Slide ferrule against elbow and secure with compression nut.
Compression Nut
Ferrule
90° Elbow
Figure T
Hot Water
Supply Line
IMPORTANT – Check to be sure that
door spring does not rub or contact the fill hose or water supply
line. Test by opening and closing the door. Re-route the lines if a
rubbing noise or interference occurs.
Drive screws
IMPORTANT –
straight and flush. Protruding screw heads will scratch the top
of the control panel and can interfere with door closing.
9
Installation Instructions
Cutting Lines
I
d
Fasten to underside
of countertop
32"
Min.
18"
Min.
Fasten to underside
p
ve
er
STEP 12 CONNECT DRAIN LINE
FOLLOW ALL LOCAL CODES AND ORDINANCES.
The drain hose molded end will fit 5/8”, 3/4” or 1” diameter
connections on the air gap, waste tee or disposer. Cut on the
marked line as required for your installation.
3/4"
1"
MPORTANT: Do not cut corrugate
portion of hose
• If a longer drain hose is required, add up to 42” of length for
a total of 10 ft. to the factory installed hose. Use 5/8” or 7/
8” inside diameter hose and a coupler to connect the two
hose ends. Secure the connection with hose clamps.
5/8"
Figure U
DRAIN LINE INSTALLATION
• Connect drain line to air gap, waste tee or disposer using
either previously determined method.
Method 1 – Air gap with waste tee or disposer
Waste Tee Installation Disposer Installation
Figure W
Method 2 – High drain loop with waste tee or
disposer
of countertop
18"
Min.
Coupler
Hose Clamp
• Secure the drain hose to the air gap, waste tee or disposer
with clamps.
NOTE: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED
10 FEET FOR PROPER DRAIN OPERATION.
Hose Clam
Figure V
Waste Tee Installation Disposer Installation
Figure X
IMPORTANT –
When connecting drain line to disposer,
check to be sure that drain plug has been
Remo
Dispos
Plug
removed. DISHWASHER WILL NOT DRAIN
IF PLUG IS LEFT IN PLACE.
TIP: Avoid unnecessary service call charges. Always be sure
disposer drain plug has been removed before attaching dishwasher
drain hose to the disposer.
10
Installation Instructions
STEP 13 CONNECT POWER
SUPPLY
Skip this step if equipped with power cord.Skip this step if equipped with power cord.
Skip this step if equipped with power cord.
Skip this step if equipped with power cord.Skip this step if equipped with power cord.
Verify that power is turned off at the source.Verify that power is turned off at the source.
Verify that power is turned off at the source.
Verify that power is turned off at the source.Verify that power is turned off at the source.
• Remove junction box cover “A”.
• Locate the three dishwasher wires, (white, black and green)
with stripped ends. Insert dishwasher wires through the
small hole in the junction box “B”.
• Secure house wiring to the bottom of the junction box with a
strain relief “C”.
• User wire nuts to connect incoming ground to green, white to
white and black to black “D”.
• Replace junction box cover “E”. Check to be sure that wires
are not pinched under the cover.
WARNING
If house wiring is not 2-wire with ground,
a ground must be provided by the installer.
When house wiring is aluminum, be sure to
use UL Listed anti-oxidant compound and
aluminum-to-copper connectors.
STEP 14 PRE-TEST CHECKLIST
Review this list after installing your dishwasher toReview this list after installing your dishwasher to
Review this list after installing your dishwasher to
Review this list after installing your dishwasher toReview this list after installing your dishwasher to
avoid charges for a service call that is not coveredavoid charges for a service call that is not covered
avoid charges for a service call that is not covered
avoid charges for a service call that is not coveredavoid charges for a service call that is not covered
by your warranty.by your warranty.
by your warranty.
by your warranty.by your warranty.
Check to be sure power is OFF.
Open door and remove all foam and paper packaging.
Locate the Owner’s Manual in the literature package.
Read the Owner’s Manual for operating instructions.
Check door opening and closing. If door does not open and
close freely or tends to fall, check spring adjustments. See
Step 1.
Check to be sure that wiring is secure under the dishwasher,
not pinched or in contact with door springs or other
components. See Step 9.
Check door alignment with tub. If door hits tub, level
dishwasher. See Step 10.
Pull lower rack out, about half way. Check to be sure it does
not roll back or forward on the door. If the rack moves, adjust
leveling legs. See Step 10.
Check door alignment with cabinet. If door hits cabinet,
reposition or relevel dishwasher. See Step 10.
Verify water supply and drain lines are not kinked or in
contact with other components. Contact with motor or
dishwasher frame could cause noise. See Step 8.
Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must be between
120°F and 150°F. A minimum of 120°F temperature is
required for best wash performance. See "Prepare Hot Water
Line", page 5.
Add 2 quarts of water to the bottom of the dishwasher to
lubricate the pump seal.
Turn on water supply. Check for leaks. Tighten connections
if needed.
Remove protective film if present from the control panel and
door.
11
Installation Instructions
STEP 15 DISHWASHER WET TEST
Turn on power supply (or plug power cord into outlet, if equipped).
Turn dial to Normal “Wash” position.
Close door.
Check to be sure that water enters the dishwasher. If water does not
enter the dishwasher, check to be sure that water and power are
turned on.
Check for leaks under the dishwasher. If a leak is found, turn power
supply off, then tighten connections. Restore power after leak is
corrected.
Check for leaks around the door. A leak around the door could be
caused by door rubbing or hitting against adjacent cabinetry. Reposition
the dishwasher if necessary. See Step 9.
The dishwasher will drain and turn off about 5 to 7 minutes after the
first fill. Check drain lines. If leaks are found, turn power off at the
breaker and correct plumbing as necessary. Restore power after
corrections are made. See Step 12.
Open dishwasher door and make sure most of the water has drained.
If not, check that disposer plug has been removed and/or air gap is not
plugged. See Step 13. Also check drain line for kinking.
Run the dishwasher through another fill and drain cycle. Check for
leaks and correct if required.
At the end of drain, open door and turn dial to OFF position.
STEP 16 REPLACE TOEKICK
Use Top 4
Screw Holes
2-Piece Toekick
Adjust Up
or Down
Figure Y
• Place 2-piece toekick against the legs of the dishwasher.
• Place the inner toekick piece (with slots) against the toekick
bracket. The slots should align with toekick bracket screw
holes. Allow the toekick to touch the floor.
• Place larger toekick over the inner piece and install 4 toekick
screws.
• Use additional 2 screws that are provided for installations
over 33-1/2” high.
• Use both toekick pieces for all installation heights.
STEP 17 LITERATURE
Be sure to leave complete literature package and installation
instructions with consumer.
Loading...