Frigidaire FGRECTWODWRH100 Wiring Diagram

PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT 37°/0°

CONTROL SETTING

Type A with Run / Start Capacitor 65°F (18°C) Ambient 90°F (32°C) Ambient

Operating Time 70 to 90% 90 to 100%

Freezer Temperature

Refrigerator Temperature

VCZ Temperature

Low Side Pressure

High Side Pressure (last 1/3 cycle)

-6° to 6°F

(-21° to -14°C)

34° to 44°F

(1° to 7°C)

-6° to 45°F

-21° to 7°C

-1 to 3 psig

(98 to 124 kPa)

69 to 83 psig

(577 to 672 kPa)

-6° to 6°F

(-21° to -14°C)

34° to 44°F

(1° to 7°C)

-6° to 45°F

-21° to 7°C

.8 to 3 psig

(107 to 120 kPa)

117 to 128 psig

(907 to 982 kPa)

Wattage (last 1/3 cycle) 45 to 55 54 to 74

Amps (running) .7 to .9 .8 to 1.1

Base Voltage 115 vac (127 vac max)

DEFROST SPECIFICATIONS

Thermal Cutout Heater Defrost Thermistor

Cut-out Watts Ohms Cut-out

Cabinet Size:

22’ CD

Freezer

Fresh Food

Ice Maker

162°F (72.2°C)

258

+/- 5

162°F (72.2°C) 70

+/- 5

51.3

+/- 5

189

+/- 5

Electronic Timer - (ADC) Defrost 34 minutes every 12-96 hours of compressor run time.

Termination

48°F

(8°C)

38°F

(3°C)

61°F

(16°C)

CONDENSER FAN MOTOR

Watts RPM Amps

.75 1.25 1100 ± 100 40 L/S

Nominal Input

Power (W) @

80% Duty

Max Input

Power (W)

Speed (R/

Min) *@80%

Duty @ 100%

Air Flow in

Free Air

(0 Pa)

.104 A Max (@12V DC/20°C)

ERROR CODES SPECIAL MODES

Display

FZ FF FZ FF Other

Er t1 Fzr Temp Sensor

Er t2 Fzr Defrost Sensor

Er t3 FF Temp Sensor

Er t4 FF Defrost Sensor

Er t5 VCZ Temp Sensor

Er t6 Ice Maker Tray Sen-

Er CE Communication Error

dl SP Chute Flapper

Interpretation Mode

Open/Shorted

Manual Defrost

Demo /

Showroom

Sabbath Sb Sb Fz - (v) and FF +

System

Diagnostics

Open/Shorted

sor Open/Shorted

UI to Main Board

Notes: Always check for pin back-outs, pinched or damaged wires before replacing components. Determine whether failure is caused by the component, main control board or wiring. Contact TID before replacing main control board. Refer to Service Manual for additional information.

Not Closed

Display Activate Deactivate

d F Fz + (^) and FF

Light On

All LEDs

Demo

Lit

+ (^) for 10 secs

Fz + (^) and FF -

(v) for 10 secs

(^) for 5 secs

Fz + (^) and Fz-

(v) for 10 secs

Fz + (^) and FF -

(v) for 10 secs

Fz - (v) and FF +

(^) for 5 secs

Fz + (^) and Fz-

(v) for 10 secs

Any Key

FRESH FOOD ICE MAKER FILL TIME ADJUSTMENT MODE

NOTE: First consider water lter condition before adjusting ll time.

Activate: Press Cube and Crush keys for 10 secs. Press FZ + (^) or - (v) key to adjust (1-4).

Deactivate: Resets to Normal Operation after 10 secs

Setting #

Pressure Condition

Fill Time

1 Very Low 8 seconds

2 Low 6.5 seconds

3 Normal 5.5 seconds

4 Very High 5 seconds

SERVICE DATA SHEET

A15500201

ICE & WATER - AUTOMATIC DEFROST

BOTTOM FREEZER - R134a

IMPORTANT SAFETY NOTE

The information provided herein is designed to assist qualied repair personnel only. Untrained persons should

not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance.

IMPORTANT

If any green grounding wires are removed during servicing, they must be returned to their original position and properly secured.

IMPORTANT: PLEASE RETURN THIS SHEET TO ITS ORIGINAL LOCATION.

SYSTEM DIAGNOSTIC MODE

Activate: Press

Deactivate: Press

Display

-- First Screen -- All LEDs on UI illuminated.

-- Second Screen -- Blank UI display, no LEDs illuminated.

8 Main Water Valve Press Cube button on, oF “on” when on and “oF” when off. ***Valve will not shut off automatically. Test has to be turned off with Cube button.

74 VCZ Balance Heater Press Cube button on, oF “on” when on and “oF” when off. Maximum run time of 5 minutes for this test.

79 Fill Tube Heater Press Cube button on, oF “on” when on and “oF” when off. Maximum run time of 5 minutes for this test.

10 Auger Motor Press Cube button on, oF “on” when on and “oF” when off.

13 Fresh Food Light Press Cube button on, oF “on” when on and “oF” when off. Open Door to check status of light.

14 VCZ Light Press Cube button on, oF “on” when on and “oF” when off. Open Door to check status of light.

17 VCZ Fan Press Cube button on, Mi, oF Fan runs at 3 speeds: Max speed when “on”, medium speed when “Mi”, and stopped when “oF”.

18 Condenser Fan Press Cube button on, Mi, oF Fan runs at 3 speeds: Max speed when “on”, medium speed when “Mi”, and stopped when “oF”.

20 Freezer Light Press Cube button on, oF “on” when on and “oF” when off. Open Door to check status of light.

38 VCC Compressor Press Cube button on, oF “on” at full speed when on and “oF” when off.

47 Ice Chute Heater Press Cube button on, oF “on” when on and “oF” when off.

62 Ice Maker Evap Fan Press Cube button on, oF

63 Flip Mullion Heater (DC) Press Cube button on, oF “on” when on and “oF” when off.

66 Dispenser Light Press Cube button on, oF “on” when on and “oF” when off.

70 Fresh Food Evap Fan Press Cube button on, Mi, oF Fan runs at 3 speeds: Max speed when “on”, medium speed when “Mi”, and stopped when “oF”.

76 VCZ Damper Heater Press Cube button on, oF “on” when on and “oF” when off.

77 VCZ Damper Press Cube button

61 Stepper Motor Valve Press Cube button

24 Freezer Drawer Switch Open/Close the Door “CL”, “OP” When the FF door is opened, an “OP” will be shown in the FF display. When the FF door is closed, a “CL” will be showin in the FF display.

25 VCZ Drawer Switch Open/Close the Door “CL”, “OP” When the FF door is opened, an “OP” will be shown in the FF display. When the FF door is closed, a “CL” will be showin in the FF display.

28 Dispenser Paddle

29 Fresh Food Sensor --

30 Freezer Sensor --

32 VCZ Sensor --

64 Humidity Sensor --

-- No Test --

Test

Freezer

Defrost Heater

Cube/Crush

Solenoid

Dispenser

Water Valve

Ice Maker

Water Valve

Fresh Food

Defrost Heater

Fresh Food IM Defrost Heater

Freezer

Evaporator Fan

Ice Chute

Flapper Motor

Ice Maker

Harvest Test

Ice Maker Bail

Arm Test

Fresh Food

Door Switch

Fresh Food

Defrost Sensor

Ambient

Temp Sensor

Freezer

Defrost Sensor

Ice Maker

Tray Sensor

Ice Maker

Defrost Sensor

Main Board

Software Paramters

Main Board

Firmware Version

Dispenser UI

Firmware Version

VCZ UI

Firmware Version

FZ + (^) and FZ- (v) for 10 secs

Activation/

Deactivation

Press Cube button

Press Cube button on, oF

Press Cube button

Press Cube button on, Mi, oF

Press Cube button

Open/Close the Door “CL”, “OP”

Press the

Dispenser Paddle

FF Display Passing result

on, oF,

Temperature

on, oF,

Temperature

on, oF,

Temperature

OP, CL,

Flashing “1”

OP, CL,

Flashing “1”

“Go”,

Flashing “1”

“Em”, Fu”,

Flashing “1”

“03”, “00”, “01”,

“02”, Flashing

“1”, Temperature

on, oF

current tempera-

ture, “OP”, “SH”

current tempera-

ture, “OP”, “SH”

current tempera-

ture, “OP”, “SH”

current tempera-

ture, “OP”, “SH”

current tempera-

ture, “OP”, “SH”

current tempera-

ture, “OP”, “SH”

current tempera-

ture, “OP”, “SH”

current tempera-

ture, “OP”, “SH”

current humidity,

“OP”, “SH”

software revi-

sion digits

rmware revi-

sion digits

rmware revi-

sion digits

rmware revi-

sion digits

Freezer Defrost Sensor Temp displayed in FF display. Increase in temp should be noticed.

FF display shows “on” when on and “oF” when off. Cube solenoid will activate. Do not leave on for more than 1 minute.

“on” when on and “oF” when off. ***Valve will not shut off automatically. Test has to be turned off with Cube button.

Fresh Food Defrost Sensor Temp displayed in FF display. Increase in temp should be noticed.

Fresh Food IM Defrost Sensor Temp displayed in FF display. Increase in temp should be noticed.

Fan runs at 3 speeds: Max speed when “on”, medium speed when “Mi”, and stopped when “oF”.

“on” when on and “oF” when off.

When activated, the freezer evaporator fan will run at high speed. “OP” when damper is open. “CL” when damper is closed. “1” will ash when damper is moving.

“OP” when chute door is open. “CL” when chute door is closed. “1” will ash when chute door is moving. “ER” will display if the door does not open or close.

Remove bucket to see rotation of tray. “Go” will be shown in the FF display when the tray is in the horizontal (home) position. A Flashing “1” will be displayed when the tray is moving. If an error is detected “ER” will be displayed.

Remove bucket to test. Allow bail arm to drop, “Em” will be displayed when tray returns to horizontal (home) position. Hold bail arm up/keep from dropping. “Fu” will be displayed when tray returns to horizontal (home) position. A Flashing “1” will be displayed when the tray is moving. “Er” will be displayed if an error is detected.

FF display will show the temperature of the corresponding evaporator defrost sensor. A drop in temperature should be noted. “03” is the OP postion. All evaporators should have refrigerant ow and the FF defrost sensor temp will be displayed. “00” is

the CL position. The IM defrost sensor temperature will be shown in the FF display. Temperature should not drop--possibly increase. “01” is the IM/FZ evaporator position. The IM defrost sensor temperature will be shown in the FF display. A drop in

temperature should be noted. “02” is the FF/IM/FZ evaporator position. The FF defrost sensor will be shown in the FF display. A drop in temperature should be noted. A ashing “1” will be shown in the FF display while the valve is moving from position to

position.

When the FF door is opened, an “OP” will be shown in the FF display. When the FF door is closed, a “CL” will be showin in the FF display.

When the paddle is pressed, “on” will be displayed in the FF display. When the paddle is released, or not pressed, “oF” will be displayed in the FF display.

No activation needed. FF display will show current sensor temperature. “OP” will show if the sensor is open. “SH” will show if the sensor is shorted.

No activation needed. Fresh food display will show current sensor temperature. “OP” will show if the sensor is open. “SH” will show if the sensor is shorted.

No activation needed. FF display will show current sensor temperature. “OP” will show if the sensor is open. “SH” will show if the sensor is shorted.

No activation needed. FF display will show current relative humidity as a percentage. “OP” will show if the sensor is open. “SH” will show if the sensor is shorted.

The current software revision will be shown simultaneously on both displays. For example: 0049953C will be shown as 0-0, 0-0, 4-4, 9-9, 9-9, 5-5, 3-3, C-C (FZ-FF).

The current rmware revision will be shown simultaneously on both displays. For example: JHB10G00 will be shown as J-J, H-H, B-B, 1-1, 0-0, G-G, 0-0, 0-0 (FZ-FF).

The current rmware revision will be shown simultaneously on both displays. For example: LHFE0700 will be shown as L-L, H-H, F-F, E-E, 0-0, 7-7, 0-0, 0-0 (FZ-FF).

The current rmware revision will be shown simultaneously on both displays. For example: MHFE0600 will be shown as M-M, H-H, F-F, E-E, 0-0, 6-6, 0-0, 0-0 (FZ-FF).

Wire Diagram A07488502

Frigidaire FGRECTWODWRH100 Wiring Diagram

Specifications and Main Features

Frequently Asked Questions

User Manual