Frigidaire E24ID74QPS1A, E24ID74QPS3A, E24ID74QPS4A, EI24CD35RS2A, EI24CD35RS3A Installation Guide

...

Dishwasher

CD.808 936 638

Installation Instructions

INSTALLER: Leave Installation Instructions with owner.

OWNER: Read your dishwasher Use and Care Manual. It contains

important safety information for operating this appliance. It also has many suggestions for getting the best results from your dishwasher.

NOTE: Put unit on its back being careful not to pinch the Water Drain Hose.

1• Remove two (2) screws at the top the kickplate assembly

2. Tilt and pull forward the kickplate to remove it. - see Figure 1. NOTE:It is not necessary to remove the outer door for installation.

Figure 1

Front

_23¾"(60,3 cm)_

le q

33¾"

(86cm),

Adjustable

35¾"

0'8im)**

Figure 3

Closed

,_241A"(61,5cm)_

Open Door

50¼"(127,6 cm)

22½"(57,1 cm)_

NOTE: Install cabinet seal to dishwasher before placing it into the cabinet

7¾"(70,4 cm) @

Figure 5

Read all instructions before installing dishwasher. For your safety, please read and observe all safety

instructions. This guide will help you anticipate drain, water, and

electrical connections, and help you select the best location for the dishwasher.

The dishwasher is provided with water heating feature. The dishwasher is intended for connection to hot water supply.

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Failure to follow this warning can result in serious injury.

Cut Hazard

To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or disassembling unit.

Heightonlyadjustableto 35%" (90,8cm)maxwhen *DIMENSIONSDONOTINCLUDEINSULATION-

installedin35 ¾" (90,8cm)maxstandardcabinetrycutout. INSULATIONBLAC_TMAYBECOMPRESSED

to 35¾"

IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2.

If unit is to be placed in a corner, there must be at least a 2-inch side clearance between the wall and the open door•

2. Floorshouldbeflatandfreeof any obstruction.

IMPORTANT: Drain, water, and electrical lines should be roughed-in before going any further.

Electrical, water, and drain lines must be confined

to shaded areas in Figure 2.

Electric conductors, water, and drain could be

damaged.

Failure to follow these instructions could result in

fire or electric shock.

NOTE: If dishwasher is installed at end of a cabinet, sides and back must be fully enclosed.

UPON INSTALLATION.

Electric Shock Hazard

Figure 4

• t iocatio_Y/water_

Figure 6

Parts Included:

Tools and Materials Needed for

Installation (Not Included)

• Drill, Electric

• Driver, Socket 5/32", 1/4", 5/16"

• Flaring Tool/Tube Cutter (for copper tubing)

• Flashlight

• Level

• Pipe Joint Compound (for iron pipe plumbing) or Pipe Th read Tape (for sealing threads)

• Pliers

• Safety Glasses

• Saw, Keyhole or 1/2", 11/2"to 2" Hole Cutters

• Screw Drivers, Slotted and Q2 Phillips (magnetic tip

preferred)

• Work gloves

• Tape, Electrical or Duct

• Measuring Tape

• Wire Stripper or Utility Knife

• Wrench, Hex-end

• Wrenches, 2 Adjustable (for copper tubing)

or2 Pipe wrenches (for iron pipe plumbing)

Parts You Will Need*(NotIncluded)

• Drain HoseClamp, 1 1/4" (3,1 cm) Diameter

• Brass Elbow, 90 °with a 3/4" ( Q 2 cm )-11.5 NH to 3/8" ( Q 2 cm )

NPT Compression fitting

• Conduit Connector (U L Listed)

• Wire Nuts, three (3) for 12-14 gauge wire (UL Listed)

•klf required:

• "Y" Branch Tailpiece and

Connector Kit (See Step 8 )

• Air Gap Kit (See Step 8 )

All the parts can be found at local hardware, electrical and

plumbing supply stores.

Electric Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death

or serious injury,

3. Locate water inlet valve behind kickplate on bottom left underside of unit. See Figure 4 The valve has a 3/4" ( 2 cm ) GHT Garden

Hose Thread with 12TPI.

4. Connect the 90 ° elbow (not included) to water inlet valve. When tightened, point elbow should point toward the left. To prevent bending of bracket or breaking of valve, avoid overtightening. See Figure 4.

Cabinet Preparation:

As a precaution, it is recommended, but not required that the

cabinets enclosing all sides of the dishwasher (including the underside of the countertop) be sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam/moisture

damage.

Electric Shock Hazard

Observe all local codes and ordinances for electrical and plumbing connections. All electrical

and plumbing work should be performed by qualified persons. Failure to follow this warning

could result in death or serious injury.

Figure 2

Make sure your location has the correct drain, water, and electrical outlets to make the connections. Do not instafl unit

under a cooktop range, Damage to tub or other components will

occur.

90° I

(45,7cm)

1" (2,5 \

(5,7 cm)

34"(86,36cm) rain.to35_"

(90,8cm)

m_x.**

24"(60,96cm)

rain.

Electrical, water,

and drain lines

must be confined

to shaded area.

Preferred

DrainAreas

**NOTA:

(90,8cm)max.

standardcabinetrycutout.

(5/16"[0,8cm]rain.

clearance

requiredfrom unitto

undersideofcountertop.)

24" (61cm)

Water line Brass Elbow

(Not Included) (Not Included) Electrical Line

Locating the Connections

1. Review dimensions in Figure 2 to locate dishwasher's drain, water, and electrical connections.

2. All utilities must be routed in shaded area in the Figure 2

Note: Locate the electrical supply and dishwasher's electrical

junction box on right underside of unit behind kickplate

assembly. See Figure 4. Determine where you will connect to hot water supply. Review Figure 4 and note the location of

water inlet valve. Determine where you will connect the drain hose.

3. Cut access holes for the Electrical, Water and Drain hoses in the cabinet within the shaded areas as shown in Figure 2.

4. The dishwasher operates on a 120 volt, 60 Hz electrical supply.

Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps.

5. Pull electrical cable through hole into installation area.

6. Be sure water inlet valve is protected from freezing. If valve freezes and ruptures, flooding may occur.

7. Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve. Extra hose length is necessary High-pressure and high-temperature Stainless Flexible hose with

a minimum inner diameter of 1/4" may be used. A shut-off valve installed outside dishwasher cabinet is best.

8. Route water supply line into installation area.

9. Stand dishwasher back upright for further installation.

IMPORTANT: Incoming hot water temperature should be at least 120°F (49°O)• Water pressure should be between 20-90 psi.

33zA,,

Adjustabl

to 353A''

1. Measure height of cabinet opening from underside of countertop to floor.

. Move dishwasherto front of installation area.

• Adjust the levelling legs.

Dishwasher Anchoring

4. Choose one of the methods of attachment below to secure unit, holes need to be pre-drilled using a Q5 drill bit regardless of

the option chosen:

a. Side Mount Cabinet Clips (Preferred Method of attachment) b. Top Mount Cabinet Clips (to be used when Side Mount

is not an available option)

CAUTION: Use extreme care in mounting the dishwasher as to not

scratch, bump or otherwise damage the console or tub.

To install the Side Mounting Clips.

Option: a Note: Install Side Mount Brackets before units is installed

into the cabinet. Insert screws into the front hole of the clips only. Use extreme caution when attaching brackets to avoid

scratching to the dishwasher or the surrounding cabinets. Depending on the depth of the cabinet, the clips have break off points which can be removed for a flush installation if necessary.

Option: a

Option: b

Depending on the depth of the cabinet, the top mount clips have break off points which can be removed for a flush installation if necessary.

Option: b

Carefully place dishwasher inside cabinet area such that is centered in opening. Use caution when moving dishwasher to prevent damage to cabinet, dishwasher and floor.

Front of door needs to be even with the front of adjoining cabinets. Front levelers should allow /16 (0,8 cm) below underside of

5 "

countertop to top of console.

Check that dishwasher is level from side to side by placing a level against the top front section of the tub. See Figure 7a.

Figure 7a

@ _ @

Adjust levelers up or down until dishwasher is level. See Figure 7blc.

Figure 7b I Figure 7c I

Figure 8

Property Damage Do not solder within 6"(15,24 cm) of the water inlet valve. Damage to the plastic parts in the valve may occur.

Use care that no sealer, dirt, or other objects enter the valve. Damage to the filter screen may occur.

Be sure the d.ishwasheris placed where t.he water inlet vawe will beKept.from Treezing. If the vawe freezes, it may rupture ano nOOolng may occur.

Water Line

1. Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn off water

supply at shut-off valve.

2. Route water line to water inlet valve as shown in Figure 4.

3. While firmly pulling water supply line into 90 ° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants.

4. Turn on water supply and check for leaks.

Electrical Supply

1. Remove junction box cover and pull house wiring into junction box. See Figure 9

2. Use a UL listed conduit connector (not included) at box to stabilize wiring.

3. Connect incoming black lead to dishwasher's black lead, incoming white lead to dishwasher's white lead and incoming

green lead to dishwasher's green lead with wire nuts. (See Grounding Instruction Warning). Wire nuts must be tight.

Figure 9

Electric Shock Hazard

Grounding Instructions:

The dishwasher must be connected to a grounded metal,

permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and

connected to the appliance's equipment grounding terminal or lead. It is the consumer's responsibility to contact a qualified installer to make sure the electrical installation

conforms with the National Electrical Code and local codes

and ordinances.

Do not connect the dishwasher to the power supply until the

appliance is permanently grounded. All wiring connections must be enclosed in the junction box.

This unit has copper lead wires. Joining aluminum building wire to stranded copper wire

should be done by a qualified electrician using materials recognized by UL and local codes. Do not use an extension cord. Such use can result in fire,

electrical shock, or other personal injury.

Failure to follow these instructions could result in death or serious injury.

Gap

i ii

3. If you connect to a sink trap,local codes may require you to install an air gap kit, (not included). The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 13 An air gap kit is available from a plumbing supply store. (If the drain

hose is installed through the floor, an air gap is necessary).

4. If you connect to a disposer, the large end of drain hose will fit.

Figure 14 (a) The knock out plug must be removed from

inside disposer inlet before making the final fit to drain hose. See Figure 14 (b).

Larger end

"hose

fits disposer

inlet fitting

Electric Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before beginning

installation. Failure to follow this warning could result in

death or serious injury

Cut Hazard

Metal color panels are sharp and should be handled with care. Wear gloves to protect

hands. Failure to follow this warning may result in

injury.

Option

Green Wire [/_

to Green Wire //_

Green Wire (Ground)

to Green tire_ Black Wire / /X\ f White Wire

, (Ground) Black Wire to White Wire

to Black Wire (Neutral) (Hot) _ _ _ (Neutral)

- -:-_':: 4 (Hot)

: .._; . Replace junction boxcover.See Figure 10

White Wire t0 Bla?k Wire IJ _ to White Wire

_'_,i Figure l O

9. Holes need to be pre-drilleld using a 05 drill to

secure unit

10. Screw mounting brackets firmly to cabinet using screws provided

installation packet. See Figure 8

11. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly, adjust rear

foot if small correction is needed until door opens and closes freely. Adjust the levelling legs. Review Figures 12, 13 and 14 to see the different ways to

Figure 11

Water Line

Electrical Line

check these items:

[] Water and electrical lines are straight out in front of the

dishwasher.

connect dishwasher to drain system. Choose method

that best suits your need.

Entry Must be Above Trap

Sink at Right

Sink at Left

2"Drain Hose Hole

Figure 12

The drain hose loop must be at least 32" (80 cm) high from the floor

to insure proper drainage.

##y,,

Branch

Tailpiece

Figure 14(a) Cut %"(1, 6 cm) connection.

/ Drain Air Gap

Sink_ []

ti <-c_:_Alternate

__ I/ _ _ I I_'- _I _'--_ _l)rain

_",__ '1 li l[ _ Floor into []

.. _ J Separate

"_R em ov_____ -_ _'_k_ Trap\ [][]

Knockout _ _ \ Sink at Right Plug in _ []

Disposer 2 (5,08 cm)

Figure 14(b) Drain Hose Hole []

The drain hose loop must be at least 32"(80 cm) high from the floor

to insure proper drainage.

5. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose.

6. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends

or kinks that might restrict drain flow.

7. Secure drain hose to sink drain, disposer, or separate trap with a clamp. IMPORTANT: Be careful not to overtighten clamp or

you may damage end of hose. Do not connect hose to

horizontal pipe between sink drain and disposer.

8. Be sure unit does not rest on drain hose. It should be free of electrical components and door springs. Do not cut corrugated

drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges.

Electric Shock Hazard If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate

assembly before placing unit into operation. Failure to follow this warning could result in

electric shock.

Water and drain lines have no kinks and move freely

behind the dishwasher.

Water supply is turned on. Joints are free of leaks.

[]

Wiring connections to junction box are tight all access

panels are secured back in place. Replace kickplate. See Figure 11

Drain hose is connected properly to outlet.

All packing materials and consumer literature have

been removed from inside unit. Dishwasher is level and securely fastened.

[]

Open and close door to make sure it does not hit

surrounding cabinet or countertop.

[]

Make _qre that all wire ties are removed from the rack assembly

Operate the machine through at

least one fill and pump-out, checking the following items:

[] At first fill, approximately 4 minutes make sure water

completely covers filter surface.

[] At pump-out: (pump-out is either when the cycle is

completed or canceled, refer to the Use and Care Manual for Start/Cancel), make sure all water is pumped out.

[] Check water connections again for leaks.

[] All three leg levelers are positioned properly.

[] Cabinet Seals are positioned on the sides of the

dishwasher.

[] Cabinet Attachment Clips are attached to the cabinet on

both corners on top of the dishwasher.

2. If you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 12.