Frigidaire FGFB68CQB, FGF326ASG, FGF366ASB, FGF355ASB, GSG3PZCCA Instructions Manual

INSTALLATIONANDSERVICE MUST BE PERFORMED BY

A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

This conversion kit must be installed by a qualified service technician in accordance with the

manufacturer's instructions and all applicable codes and requirements of the authority having jurisdiction. Failure
to follow instructions may result in fire, explosion or production of carbon monoxide causing property damage,
personal injury or loss of life. The qualified service agency is responsible for the proper installation ofthis kit. The
installation is not proper and complete until the operation ofthe converted appliance is checked as specified in the
manufacturer's instructions supplied with this kit.

Before proceeding with the conversion, shut offthe gas supply before disconnecting electrical power

to the range. Be sure both power supplies are off before installing the conversion kit. Failure to do so could cause
serious bodily injury.

Determine the combination of top burners that are featured on your range. Then identify the parts you need from
this kit to complete the LP. conversion. When burners are converted from Natural to LP the BTU rating is as follows:

5,000 BTU* Natural gas to 4,500 BTU* LP Gas 9,500 BTU* Natural Gas to 8,000 BTU* LP Gas

12,000 BTU* Natural Gas to 10,000 BTU* LP Gas 14,000 BTU* Natural Gas to 11,000 BTU* LP Gas

Quantity

1
1
1
1
1
1
1
1
1
1
1
1
1

4

1

Part Number

316037526
316248105
316005215
316005216
316005217
316005218
316005219
316005220
316005221
316005222
316241200
316237904
316237905
316237906
316237907

Part Description
L.P. Conversion Kit Label

Instructions for converting range to LP Gas
Rating Plate - English

Rating Plate - English
Rating Plate - English

Rating Plate - English
Rating Plate - French

Rating Plate - French
Rating Plate - French
Rating Plate - French

L.P. Conversion Label
Orifice - 11,000 BTU*

Orifice- 10,000 BTU*
Orifice - 8,000 BTU*
Orifice - 4,500 BTU*

Notes
English and French

English, French and Spanish
4 - 8K

3+1
2+1+1
1+1+1+1
4 - 8K

3+1
2+1+1

1+1+1+1
English, French and Spanish

RED
GREEN
NO COLOR
BLUE

*Note: For operation at elevations above 2000 ft., appliance rating shall be reduced at the rate of 4 percent for each 1000
ft. above sea level.

IM PORTANT: After replacing the natural gas to LP orifices; be sure to keep the original factory installed natural gas
orifices for future range conversion back to natura! gas. The factory orifices are marked with 101 for 5,000 BTU; 154

for 9,500 BTU; 175 for 12,000 BTU and 193 for 14,000 BTU.

Tools Required for L.P. Conversion:

3/8", 1/2" and 5/8" Open End Wrench

1/8" Wide Flat Blade Screwdriver
7mm Nutdriver

PIN 316248105 (0104)

Frangais - Pages 6-10

Espa5ol - Paginas 11-15

How to Convert the Range for use with LP/
Propane Gas

1. Convert the Pressure Regulator

To access the gas regulator, remove the storage drawer or warmer
drawer. If equipped with a storage drawer, open and remove the drawer
completely. For models equipped with a storage drawer or front panel,

remove the storage or front panel and skip steps a & b below. For models
equipped with warmer drawer, follow all the instructions below to remove

the warmer drawer.
a. _!_ Electrical Shock Hazard can occur and result in

serious injury or death. Disconnect electrical power to the range
before removing the warmer drawer for servicing.

b. Locate glide lever on each side of drawer, pull up on the left glide lever

and push down on the right glide lever (See Figure 1).
c. Pull the drawer away from the range (See Figure 2).
d. Remove the regulator access cover if equipped. Do not remove the

Pressure Regulator or allow it to turn.
e. Remove the dust protector from the cap. Using a 5/8" wrench,

unscrew the cap from the pressure regulator. Do not remove the

spring from the regulator.
f. Turn the cap over so the hollow end faces outward. Place the solid

end of the cap into the loop end of the dust protector (See Figure 3).
g. Replace the cap on the regulator. The letters LP should be visible on

the exposed end of the cap. Snap the dust protector over the

regulator cap.

Pull up with finger

Pressure

Front access to Regulator: Regulator

Open storage or warmer drawer, located at

or remove lower panel rear of

(on some models)

FIGURE 2

Dust

Protector

Spring

Left Glide

Push down with finger

FIGURE 1

Hollow End Solid End

Towards Towards

Regulator Regulator

FIGURE 3

Natural Gas Orifice to LP Orifice Conversion for each type of burner

5,000 BTU Natural Gas

converts to 4,500 BTU LP Gas

Install(blue)orifice68mm for LP 9,500BTU NaturalGas

for Natural Gas for LP/Propane Gas

converts to 8,000BTU LP Gas

Install orifice (nocoIor) ,89mmfor LP

14,000 BTU Natural Gas 12,000 BTU Natural Gas

converts to 11,000 BTU LP Gas converts to 10,000 BTU LP Gas

Install (red) orifice !.01mm for LP Install (green) orifice .95mm for LP

FIGURE 4