Frigidaire FGEF3042KFA, FGEF3032KWA Wiring Diagram

SERVICE DATA SHEET

RTD SCALE

Temperature (°F) Resistance (ohms)

32 ± 1.9 1000 ± 4.0

75 ± 2.5 1091 ± 5.3

250 ± 4.4 1453 ± 8.9

350 ± 5.4 1654 ± 10.8

450 ± 6.9 1852 ± 13.5

550 ± 8.2 2047 ± 15.8

650 ± 9.6 2237 ± 18.5

900 ± 13.6 2697 ± 24.4

Electric Ranges with ES 330/330i Electronic Oven Controls

ELECTRONIC OVEN CONTROL (REAR VIEW)

E.O.C. ELECTRICAL CONNECTIONS P5 Connections

NOTICE - This service data sheet is intended for use by persons

having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. The manufacturer cannot be responsible, nor assume any liability for injury or damage of any kind arising from the use of this data sheet.

SAFE SERVICING PRACTICES

To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices be observed. The following are examples, but without limitation, of such practices.

1. Before servicing or moving an appliance remove power cord from electrical outlet, trip circuit breaker to OFF, or remove fuse.

2. Never interfere with the proper installation of any safety device.

3. GROUNDING: The standard color coding for safety ground wires is GREEN or GREEN WITH YELLOW STRIPES. Ground leads are not to be used as current carrying conductors. It is extremely

important that the service technician reestablish all safety grounds prior to completion of service. Failure to do so will create a potential safety hazard.

4. Prior to returning the product to service, ensure that:

• All electric connections are correct and secure.

• All electrical leads are properly dressed and secured away from sharp edges, high-temperature components, and moving parts.

• All uninsulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal parts and panels.

• All safety grounds (both internal and external) are correctly and securely reassembled.

OVEN CALIBRATION

Set the electronic oven control for normal baking at 350°F. Obtain an average oven temperature after a minimum of 5 cycles. Press cancel to end bake mode.

TEMPERATURE ADJUSTMENT

1. Set EOC to bake at 550°F.

2. Within 5 seconds of setting 550°F, press and hold the bake pad for approximately 15 seconds until a single beep is heard (longer may cause F11 shorted keypad alarm).

3. Calibration offset should appear in the display.

4. Use the slew keys to adjust the oven temperature up or down 35°F in 5°F increments.

5. Once the desired (-35° to 35°) offset has been applied, press cancel.

Note: Changing calibration affects normal Bake mode. The adjustments made will not change the Self-Cleaning cycle temperature.

SIMMER SELECT PCB (some models)COOKTOP LOCKOUT PCB (some models)

ELECTRONIC OVEN CONTROL FAULT CODE DESCRIPTIONS

Fault Code

F10

F11

F12

F13

Likely Failure Condition/Cause

Runaway Temperature.

Shorted Keypad.

Bad Micro Identification.

Bad EEPROM Identification/Checksum error.

P8 Cooktop Lockout Connections

Suggested Corrective Action

1. (F10 only) Check RTD Sensor Probe & replace if necessary. If oven is overheating, disconnect power. If oven continues to overheat when the power is reapplied, replace EOC. Severe overheating may require the entire oven to be replaced should damage be extensive.

2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power.

3. (F11, 12 & 13) If fault returns upon power-up, replace EOC.

(some models)

IMPORTANT

DO NOT REMOVE THIS BAG

OR DESTROY THE CONTENTS

WIRING DIAGRAMS AND SERVICE

INFORMATION ENCLOSED

REPLACE CONTENTS IN BAG

p/n 316904404 (0903)

RESISTANCE TEMPERATURE DECTECTOR

F30

F31

F40

F90

F91

F92

F93

F94

CIRCUIT ANALYSIS MATRIX

Open probe connection.

Shorted Probe connection.

Cooktop Lockout error (some models).

Maximum oven door unlock time exceeded.

Maximum oven door unlock attempts exceeded.

Maximum oven door open time exceeded.

Maximum oven door lock time exceeded.

Maximum oven door lock attempts exceeded.

1. (F30 or F31) Check resistance at room temperature & compare to RTD Sensor resistance chart. If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring harness between EOC & Sensor Probe connector.

2. (F30 or F31) Check resistance at room temperature, if less than 500 ohms, replace RTD Sensor Probe. Check for shorted Sensor Probe harness between EOC & Probe connector.

1. (F40) Check the wiring.

2. (F40) Replace the Cooktop Lockout Control Board.

3. (F40) Replace EOC.

1. (F90, 91, 92, 93 & 94) Check the wiring between EOC & Lock Motor Micro Switch.

2. (F90, 91, 92, 93 & 94) Replace the Motor Door Latch assembly if necessary.

3. (F90, 91, 92, 93 & 94) Check for binding of the Latch Cam, Lock Motor Rod & Lock Motor Cam.

4. (F90, 91, 92, 93 & 94) Check to see if Lock Motor Coil is open. If open, replace Lock Motor Assembly.

5. (F90, 91, 92, 93 & 94) Lock Motor continuosly runs - if Micro Switch is open, replace Lock Motor Assembly.

6. (F92, 93 & 94) Check oven door Light Switch - if open, replace Switch.

7. If all situations above do not solve problem, replace EOC.

(some

MDL

(some models)

models)

GENERAL TROUBLESHOOTING SCHEMATICGENERAL TROUBLESHOOTING DIAGRAM