Frigidaire FGC36S5ABC, FGC36S5AWC, FGC36S6ABC, FGC36S6ASC, FGC36S6HSA Installation Guide

...

_NSTALLAT_ON AND SERVICE MUST BE PERFORMED BY

A QUAUHED _NSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL _NSPECTOR'S USE.

READ AND SAVE THESE _NSTRUCT_ONS FOR FUTURE REFERENCE.

if the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal iniury or death. FOR YOUR SAFETY:

J Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

J WHAT TO DO iF YOU SMELL GAS:

Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Immediately call your gas supplier from a neighbor's phone. Follow the gas suppHer's instructions.

* ff you cannot reach your gas supplier, call the fire department. J Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Cooktop Dimensions

* 30" min. for unprotected cabinet

24" min. for protected surface

. LENGTH..

30" Models 30 (76.2) 21 Y2(54.6) 3 I/s (7.9)

36"X 21Y2"Models 36(91.4) 21 Y2(54.6) 3Vs(7.9)

B.WIDTH C. DEPTH '

Cooktop Cutout Dimensions

Figure 1

MIN, D. LENGTHMAX.

26 s/s(67.6) 267/s (68.3)

32 34(83.2) 33 (83.8)

MIN. E.WIDTH MAX:

19 (48.3) 19 3/s(49.2)

19 (48.3) 19 S/s(49.2)

30" Min.*

(76.2 cm) Min.*

E DEPTH

BELOW

COOKTOP_ (Min.) . (Min.)

5 (12.7) 23A(7) 2Y4(5.7)

36"X 18" Models 36 (91.4) 18 (45.7) 3 Y2(8.9)

34 1/4(87) 34 s/s(87.3)

16 s/s(42.2) 16 3A(42.5)

All dimensions are in inches (cm). Dimension Fisfor clearance under cooktop for gas connection. NOTE: Wiring diagrams for these appliances are enclosed in this booklet. Only some models are available in Canada.

', Recycled paper

5 (12.7) 4Y4(10.8) 3 (7.6)

P/N 318201450 (0410) Rev B

English - pages 1-8

Espanol- pages 9-17

Franqais - pages 18-26

Wiring Diagrams - pages 27-28

!3" (33 cm)

Max, Depth For

Cabinet Installed Above Cooktop.

A Min.

30" (76.2 cm) Min, Clearance Between

the Top of the

Cooking Platform

and Unprotected

Wood or Metal

Cabinet

Dimension K isthe

Minimum Clearance

Required From Left

Side To Adjacent

Combustible Surface.

18" Min,

(45.7cm Min.)

Dimensions J isthe Minimum

Distance Required Between Rear

of Cooktop to Adjacent

Combustible Surfaces.

Clearance

Dimension H istile

Minimum Clearance

Required From Right

Side To Adjacent

Combustible Surface.

To eliminate the risk of

burns or fire by reaching over heated surfaces, cabinet storage space located above the cooktop should be avoided. If cabinet storage is provided, risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of tile

cabinets.

Figure 2 - COUNTERTOP CUTOUT OPENING

30" Models 4" (10.2 cm) 1 _/_"(3.8 cm) 7" (17.8 cm)

36" X 21_/_" Models 5" (12.7 cm) 1 _/_"(3.8 cm) 5" (12.7 cm)

36" X 18" Models 3" (7.6 cm) 3 3A" (9.5 cm) 3" (7.6 cm)

Important Notes to the Installer

1. Readallinstructionscontainedintheseinstallation instructionsbeforeinstallingthecooktop.

2. Removeallpackingmaterialbeforeconnectingtile electricalsupplytothecooktop.

3. Observeallgoverning(:odesandordinances.

4. Besuretoleavetheseinstructionswithtileconsumer.

important Note to the Consumer KeeptheseinstructionswithyourUseandCare Guide for

future reference.

IMPORTANT SAFETY INSTRI

Installation of this cooktop must conform with local codes or, in the absence of local (:odes, with tile National Fuel

Gas Code ANSI Z223.1--1atest edition in the United States, or in Canada, with the Canadian Fuel Gas Code, CAN/CGA B149 and CAN/CGA B149.2.

This cooktop has been design certified by American Gas Association(A.G.A.). As with any appliance using gas and generating heat, there are certain safety precautions you should follow. You will find them in tile Use and Care Guide, read it carefully.

Be sure your cooktop is installed and grounded

properly by a qualified installer or service technician.

• This cooktop must be electrically grounded in

accordance with local codes or, in their absence, with the National Electrical Code ANSI/NFPA No,

70--Jatest edition in the United States, or in Canada, with the Canadian Electrical Code, CSA

C22.1 Part 1.

• The burners can be tit manuatly during an

electrical power outage. To light a burner, hold a tit match to the burner head, then slowly turn the

Surface Control knob to LJTE. Use caution when tighting burners manually.

• Do not store items of interest to children in the

cabinets above the cooktop, Children could be seriously burned climbing on the cooktop to reach

items.

• To eliminate the need to reach over the surface

burners, cabinet storage space above the burners should be avoided.

Adjust surface burner flame size so it does not

extend beyond the edge of the cooking utensil,

Excessiveflame is hazardous.

Never use your cooktop for warming or heating the room. Prolonged use of the cooktop without adequate ventilation can be hazardous.

• Do not store or use gasotine or other flammable vapors and liquids near this or any other appliance. Explosions or fires could result.

The electrical power to the cooktop

must be shut off while line connections are being made, Failure to do so could result in serious

injury or death.

1. Before Installing the Cooktop

Foam Tape

Figure 3

A roll of foam tape is supplied loose and packed in tile literature package. Install the foam around the perimeter of the flange of the burner box, at a distance of 1/4"(0.6 cm) from the edge of the glass or porcelain top. Apply the exposed adhesive side of the tape against the underside of the glass or the burner box surface (see figure 3).

NOTE: This tape seals the underside of the cooktop to the counter. Do not remove this foam tape. This tape prevents entry of air for normal gas combustion, and prevents liquids from leaking under the cooktop.

After inserting the cooktop into the countertop opening, make sure the unit is sitting on the metat flange around the top of the burner box. Cooktop must not sit on the glass or porcelain top. Avoid cutting an oversized hole in the countertop.

All mounting hardware

must be used to secure

the builtqn oven to the

cabinets. Refer to the builtqn oven installa-

tion instructions.

208/240 Volt grounded

junction box for builtqn

oven,

This cooktop may be in- stalled over certain built-

in electric oven models.

Approx. 3"

(7.6cm)

Side filler panels are necessaryto isolate the unit from adjoining cabinets. Panel height should allow for installation of approved cooktop models. See "Typical Gas Cooktop In-

stallation Over an Electric Builtqn Oven Installed Under the Counter" in this booklet.

32" Min.** (81.3 cm Min.**)

36" Min. /_ (91.4 cm Min.)

Use 3A"(1.9 cm) plywood, installed on two runners, flush with toe plate. Must be capable of supporting 150 Ibs (68 kg).

4 1/2"Max. *

* If no cooktop is installed directly over

the oven unit, 5" (!2.7 cm) maximum

isallowed.

** 32" (8! .3 cm) rain. from top of cabinet

to top of runners must be maintained.

Figure 4 - TYPICAL UNDER COUNTER INSTALLATION OF AN ELECTRICBUILT-IN OVEN

Cut an opening in wood basemini- mum 9" x 9" (22.9 cm X 22.9 cm), 2" (5.1 cm) from left side filler panel, to route armoured cable to

junction box.

(11.4 cm Max.*)

CUTOUT DIMENSIONS

MODEL' E, HEIGHT I F,WIDTH' G. DEPTH

27" (68,6 cm) 28 I/8" (71 4 cm) Min 247/8" (63,2 cm) Min

Wall Oven 28 Vg" (72,7 cm) Max 25 V4" (64,1 cm) Max

30" (76,2 cm) 28 _¼"(718 cm) Min 28 Vz" (72,4 cm) Min

Wall Oven 28718``(7:3.3 crn) Max. 29" (7:3.7 crn) Max. 24" (61 crn)

WITH COOKTOP MOUNTED ABOVE

23 1A"(59 7 cm)

18" Max.

(45.7 cm)

Flexible

Wall Oven Cabinet

Figure 5 - TYPICAL GAS COOKTOP INSTALLATION OVER

AN ELECTRICBUILT-IN OVEN INSTALLED UNDER THE COUNTER

2. Wall Outlet Location

12" (30.5 cm)

Cabinet sides or

filler panel

5" Max. 6 Y2" Min.

Flare (1271cm) (If_:m)

Flare

Union

3. Cramp Down Information

Once the cooktop is installed in the counter opening, you must clamp the unit down as shown.

Cooktop _ Foam Tape /

120V/6OHz

Grounded

Outlet

Pressure Regulator

Manual

Shutoff

Valve

4" (_0.2 cm)

Right Side of

Cabinet

(To be

accessible for shut-off valve

operation)

Countertop

NOTE: If an outlet is not available,

have one installed by a qualified

technician.

I 10" (25.4 cm)

: i

i Recommende ' 120V grounded outlet on I rear wall

CL of unit

"CL of unit

Figure 6

22"

(55.9 cm)

Angle Bracket_

J _'_"_ Thumb Screw

Figure 7

To clamp down, insert the bracket with the offset side of the angle into the slots on each side of the unit. The thumb screw should then be run through the bracket, up against the bottom of the counter. Tighten until the unit

draws down.

4. Provide an Adequate Gas Supply

This cooktop is designed to operate on natural gas at 4" (10.2 cm)of manifold pressure only.

A pressure regulator is connected in series with the manifold on tile cooktop and must remain in series with

tile supply line.

For proper operation, tile maximum inlet pressure to the regulator must be no mere than 14" (35.6 cm) of

water column (W.C.) pressure.

For checking the regulator, the inlet pressure must be at least 1" (2.5 cm) (or 2.5 kPa) greater than the regulator

manifold pressure setting. The regulator isset for 4" (10.2 cm) of manifold pressure, tile inlet pressure must

be at least 5" (12.7 cm).

The gas supply line to the cooktop should be Y2" (1.3 cm) or sA" (7.9 cm) pipe.

5. LPiPropane Gas Conversion

This appliance carl be used with Natural gas or LP/ Propane gas. It is shipped from the factory for use with natural gas.

If you wish to convert your cooktop for use with LP/ Propane gas, use the supplied fixed orifices in tile package containing tile installation Instructions Manual, in a bag marked "FOR LP/PROPANEGAS CONVERSION". Follow the installation instructions packaged with tile

orifices.

5. Install Pressure Regulator

Install the pressure regulator with the arrow on the regulator pointing up toward the unit in a position where

you can reach the access cap.

FIRE HAZARD. Do not make the

connection too tight. The regulator is die cast. Overtightening may crack the regulator resulting in a gas leak and possible fire or explosion.

Manual GAZFLOW Pressure Shutoff Flare _@ Flare Regulator

Valve Union Union

On_ Flexible Connector[ _®'''"'"'_®J

Off

All connections must be wrench4ightened

Figure 8

Assemble the flexible connector from the gas supply pipe to the pressure regulator in order: 1- manual shutoff valve, 2- _/2" nipple, 3- _/2" flare union adapter, 4- flexible connector, 5- _/2" flare union adapter, 6- _/2" nipple, pressure regulator.

Use pipe-joint compound made for use with Natural and LP/Propane gas to seal all gas connections. If flexible

connectors are used, be certain connectors are not kinked.

The conversion must be performed by a qualified service technician in accordance with the manufacturer's

instructions and all local codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. Tile qualified agency performing this work assumes responsibility for the conversion.

Failure to make the appropriate

conversion can result in personal injury and property damage.

Important: Remove all packing material and

literature from cooktop before connecting gas and electrical supply to cooktop.

The supply line should be equipped with an approved shutoff valve. This valve should be located in the same

room as tile cooktop and should be in a location that allows ease of opening and closing. Do not block access to the shutoff valve. The valve is for turning on or shutting off gas to the appliance.

To Appliance

Shutoff Valve

Figure 9

Open the shutoff valve in tile gas supply line. Wait a few minutes for gas to move through the gas line.

To gas supply line

Checkfor leaks. Leaktestingoftheapplianceshallbe conductedaccordingtothemanufacturer'sinstructions. Afterconnectingthecooktoptothegassupply,check tilesystemforleakswithamanometer.Ifa manometer isnotavailable,turnonthegassupplyandusealiquid leakdetector(orsoapandwater)atalljointsand

connectionstocheckforleaks.

Donotuseaflameto checkforleaks

fromgasconnections.Checkingforleakswithaflame mayresultinafireorexplosion.

Tightena[[connectionsif necessaryto preventgas leakageinthecooktopor supplyline.

Checkalignmentof valvesafterconnectingthe cooktoptothegassupplytobesurethecooktop manifoldpipehasnotbeenmoved.

Preferred Method

Grounding type wall receptacle Power supply cord with

3-prong grounding plug

Figure 10

Where a standard 2-prong wall receptacle is installed, it

is the personal responsibility and obligation of the consumer to have it replaced by a properly grounded 3- prong wall receptacle.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

Disconnectthiscooktopandits individualshutoff valvefromtilegassupplypipingsystemduringany pressuretestingofthatsystemattestpressuresgreater thanY2psig(3.5kPaor14"(35.6cm)watercolumn).

Isolatethecooktopfrom the gassupplypiping systembyclosingitsindividualmanualshutoffvalve duringanypressuretestingoftilegassupplypiping systemattestpressuresequaltoor lessthanY2psig

(3.5 kPa or 14" (35.6 cm) water column).

7, Connect Electricity to Gas Cooktop

Electrical Requirements

120 volt, 60 Hertz, properly grounded branch circuit protected by a 15 amp circuit breaker or time delay fuse. Do not use an extension cord with this cooktop.

Grounding Instructions

IMPORTANT Please read carefully.

For personal safety, this appliance must be properly grounded.

Tile power cord of this appliance is equipped with a 3- prong (grounding) plug which mates with a standard 3- prong grounding wall receptacle (see Figure 8) to minimize the possibility of electric shock hazard from the appliance.

Disconnect electrical supply cord from

wall receptacle before servicing cooktop.

8. Check Operation

Refer to the Use and Care Guide packaged with the cooktop for operating instructions and for care and cleaning of your cooktop.

Do not touch the burners. They may be hot enough to cause burns.

Install Burner Caps This cooktop is equipped with sealed burners as shown (see Figure 11).

T--y

Burner Base-_

Burner Pan /

Built-in) ',

Gas Opening

The wall receptacle and circuit should be checked by a qualified electrician to make sure the receptacle is properly grounded.

Electrode --/

Figure 11

A. Unpack burner bases and caps. B. Place burner base over each gas opening tube. C. Make sure the burner is properly aligned and

leveled. Place burner cap over each burner base.

NOTE: There are no burner adjustments necessary on this cooktop.

2. Turn on Electrical Power and Open Main Shutoff Gas Vatve

Check the Igniters Operation of electric igniters should be checked after cooktop and supply line connectors have been carefully checked for leaks and the cooktop has been connected to electric power. To operate the surface burner:

A. Push in and turn a surface burner knob to the

LITE position. You will hear a little ticking noise; this is the sound of tile electric ignitor which lights the burner.

B. After the burner lights, turn to the desired flame

size. The controls do not have to be set ata particular mark. Use the marks as a guide and

adjust the flame as needed.

Adjust the "LO" or "SIMMER" Setting of Surface Burner Valves (see Figure 12) Push in and turn each control knob to the "LO" (or

"SIMMER") setting. The "LO" setting of each burner has been set at the factory to the lowest setting available to provide reliable reignition of the burner. If it does not stay lit on the"LO" setting, check the setting asfollows.

A. Allow cooktop to cool to room temperature. B. Light all burners by turning each control knob to

LITEuntil burners ignite, and then set them at

"HI".

C. _turn the knob to tile LOWEST POSITION. D. If burner goes out, readjust valve asfollows;

Remove the surface burner control knob, insert a thin-bladed screw driver into tile hollow valve

stem and engage the slotted screw inside. Flame size can be increased or decreased with

the turn of the screw. Adjust flame until you can quickly turn knob from HI to LOWEST POSITIONwithout extinguishing the flame. Flame should be as small as possible without going out.

E. If you need to adjust another burner, repeat the

steps from A to D above until all burners operate properly.

When All Hookups are Complete

Make sure all controls are left intile OFF position.

Make sure the flow of combustion and ventilation air to the cooktop is unobstructed.

Model and Serial Number Location

Tile serial plate is located on the underside of the cooktop.

When ordering parts for or making inquires about your range, always be sure to include the model and serial numbers and a lot number or letter from tile serial plate of your cooktop.

Your serial plate also tells you the rating of tile burners, the type of fuel and the pressure the cooktop was adjusted for when it left the factory.

Hollow Valve

System

Before You Call for Service

Read tile Avoid Service Checklist and operating instructions in your Use and Care Guide.

Check to make sure the house fuse or circuit breaker for your cooktop are not blown or open.

Figure 12

LA INSTALACI6N Y EL SERVICIO DEBEN SER REAUZADOS POR UN

INSTALADOR CAUNCADO.

IMPORTANTE: GUARDE ESTAS [NSTRUCCIONES PARA USO DEL

INSPECTOR ELECTRICO LOCAL.

LEA Y GUARDE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIA

Si todas [as [nstrucdones de este manual no son observadas a [a [etra, se puede ocurr[r

[ncend[os o exp[osiones que pueden causar dafios materia[es, [esiones o [a muerte. PARA SU SEGURDAD:

-- No a[macene o uti[ke gaso[ina u otros vapores y [iquidos inflamaMes cerca de este o cualquier otro artefacto.

-- QUE HACER S[ HAY FUGAS DE GAS

• No intente de encender ningun artefacto

No toque ningun interruptor electrko; no uti[ke ningun aparato t_mefonico en su edifido. Llame inmediatamente el abastecedor de gas desde el temefono de un vedno. Siga [as instrucciones dem

abastecedor de gas.

Encaso que no puede contactar el abastecedor de gas [lame a[ departamento de bomberos.

-- La instaJaci6n y el servido t_lefonico deben ser reamizados por un instamador caIificado, por un servido tecnico certificado o por e[ abastecedor de gas.

Dimensiones de la plancha de cocinar a gas

* 30" rain. para un armario protegido.

24" rain. para una superficie no

protegida.

30" Min.*

__ I_-.......B..... (76.2 cm) Min.*

Dimensiones del hueco para la plancha de cocinar a gas

Figura 1

MODELO " " PROFUNDIDAD PORDEBAJODE

30" Models 30 (76.2) 21 Y2 (54.6) 3 Vs (7.9) 26 s/s (67.6) 267/8 (68.3) 19 (48.3) 19 3/8 (49.2) 5 (12.7) 234 (7) 2Y4(5.7)

36" X 21V2" [Vbdels 36 (91.4) 21 Y2 (54.6) 3 Vs (7.9) 32 34 (83.2) 33 (83.8) 19 (48.3) 19 3/s (49.2) 5 (12.7) 234 (7) 2Y4 (5.7)

36"X 18" Models 36 (91.4) 18 (45.7) 3 1/_(8.9) 34 1/4(87) 34 3/8(87.3) 16 S/s(42.2) 16 34 (42.5) 5 (12.7) 4V4 (I0.8) 3 (7.6)

Todas las dimensiones se dan en pulgadas (cm)_ La dimensi6n F este por debajo de la plancha de cocinar para la conexi6n de la linea de suministro de gas NOTA: Se adjunta los diagramas de cables de esta plancha de cocinar con el [ibreta. 5olamente a[gunos mode[os est_qn disponib[es en Canad_i_

_ Papel reciclado

I A I B I C I PROFUNDIDAD L M

ALTU RA ANCHURA PLANCHA (MIn) (MIn)

I I I I MiN. D, ALTURA MAx, iVliN. E, ANCHURA MAx. I LACOCINARDE[ " I :

DIMENsIoNEs DEL HUECO F.

P/N 318201450 (0410) Rev B

English - pages 1-8

Espa¢_ol- pages 9-17

Francais - pages 18-26

Diagrama de la instalaci6n al_mbrica - pages 27-28

+ 19 hidden pages