Frigidaire FGMV185KW, FGMV205KB, FGBM205KF, FGBM185KW, FGBM185KB Installation Manual

...

INSTALLATION INSTRUCTIONS

Over The Range Microwave Oven

BEFORE YOU BEGIN

IMPORTANT

• inspector’s use.

IMPORTANT

• coordinates.

•

NOTE TO INSTALLER – Be sure to leave these

instructions with the Consumer.

•

NOTE TO CONSUMER – Keep these instructions for

future reference.

• SKILL LEVEL – Installation of this appliance requires basic mechanical and electrical skills.

Save these instructions for local

Observe all governing codes and

Read these instructions completely and carefully.

1 MOUNTING SPACE

This Over the Range Microwave Oven requires a mounting spa ce on a wall as s hown i n Figu re 1. It i s desi gned to be use d with standard 12" wall cabinets. The maximum depth is 13".

13” max depth.

30"

15.5"

30" or more

Backsplash

At least 2"

from cooking

surface

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

• Please read all instructions thoroughly before installing the Over the Range Microwave Oven. Two people are recommended to install this product.

• If a new electrical outlet is required, its installation should be completed by a qualiﬁ ed electrician before the Over the Range Microwave Oven is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.

2 WALL CONSTRUCTION

This Over the Range Microwave Oven should be mounted against and supported by a ﬂ at vertical wall. The wall must be ﬂ at for proper installation. If the wall is not ﬂ at, use spacers to ﬁ ll in the gaps. Wall construction should be a minimum of 2" x 4" wood studding and 3/8" or more thick dry wall or plaster/lath. The mount ing sur faces mus t be c apable o f suppor ting weig ht of 110 pounds—the oven and contents—AND the weight of all items which would normally be stored in the top cabinet above the unit.

The unit should be attached to a minimum of one 2" x 4" wall stud.

To ﬁ nd the location of the studs, one of the following methods may be used:

A. Use a stud finder, a magnetic device which locates the

nails in the stud.

B. Use a hammer to tap lightly across the mounting surface

to find a solid sound. This will indicate stud location.

66" or more

from ﬂ oor

Figure 1

As a guide to installation, see page 8 for Mounting Template Information.

The center of the stud can be located by probing the wall with a small nail to ﬁ nd the edges of the stud and then placing a mark halfway between the edges. The center of any adjacent studs will normally be 16" or 24" to either side of this mark.

NEED HELP?

For customers in the United States and Canada United States: 1-800-944-9044 Canada: 1-800-265-8352

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

316902446

February 2011

TINSEB294WRRZ-EL01

Printed in Thailand

INSTALLATION INSTRUCTIONS

3 ELECTRICAL GROUNDING INSTRUCTIONS

Thi s applia nce must be gr ounded. This o ven is equ ipped wi th a cord having a grounding wire with a grounding plug. It must be p lugged i nto a wall recepta cle that is pr operly i nstall ed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current.

WARNING - Improper use of the grounding plug can result in a risk of electric shock.

ELECTRICAL REQUIREMENTS

The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE GROUNDING PIN FROM THE PLUG.

DO NOT USE AN EXTENSION CORD. If the power supply cord is too short, have a qualiﬁ ed electrician or serviceman install an outlet near the appliance.

The Power Supply Cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit, single grounded receptacle. The receptacle should be located inside the cabinet directly above the Microwave Oven mounting location as shown in Figure 2.

NOTE:

1. If you have any questions about the grounding or electrical instructions, consult a qualiﬁ ed electrician or serviceperson.

2. Neither Electrolux nor the dealer can accept any liability for damage to the oven or personal injury resulting from failure to observe the correct electrical connection procedures.

4 HOOD EXHAUST DUCT

When the hood is vented to the outside, a hood exhaust duct is r equir ed. Al l ductwork m ust b e metal ; absolute ly do n ot us e plastic duct. Check that all connections are made securely. Please read the following carefully:

EXHAUST CONNECTION: The hood exhaust has been designed to connect to a standard 3 duct is required, a rectangular-to-round adapter must be used.

REAR EXHAUST: If a rear or horizontal exhaust is to be used, care should be taken to align the exhaust with the space between the studs, or wall should be prepared at the time it is constructed by leaving enough space between wall studs to accommodate exhaust.

MAXIMUM DUCT LENGTH: For satisfactory air movement, the total duct length of 3 duct should not exceed 140 feet.

Elbows, adapters, wall caps, roof caps, etc. present additional resistance to air ﬂ ow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total length, add the equivalent lengths of all transitions and adapters plus the length of all straight duct sections. Figure 3 shows the approximate feet of equivalent length of some typical ductwork parts. Use the values in parentheses for calculating air ﬂ ow resistance equivalent, which should total less than 140 feet.

NOTE:

Furnace duct sealing tape is recommended to seal duct connections to the Exhaust Dampener Assembly.

/4" x 10" rectangular duct. If round

/4" x 10" rectangular or 6" diameter round

Ground

Receptacle

Opening for Power Cord

Figure 2

90° Elbow (10 ft.)

90° Elbow (25 ft.)

45° Elbow (5 ft.)

Figure 3

Adaptor (5 ft.)

Wall cap (40 ft.)

10" Wide Elbow (10 ft.)

Roof cap (24 ft.)

INSTALLATION INSTRUCTIONS

5 TOOLS RECOMMENDED FOR

INSTALLATION

• Phillips Screwdriver

• Electric Drill

• 1/2", 5/8" and 3/32" Drill Bits

• 1 1/2" Wood Bit or Metal Hole Cutter (if metal cabinet is used)

• Saw to cut exhaust opening (if needed)

• Protective Drop Cloth for product and range - you may also use carton for protection

• Scissors

• Pencil

• Measure

• Tape

6 INSTALLATION HARDWARE

The INSTALLATION HARDWARE items ➀ - ➅ are in a small bag. All items are in a bag packed below the oven.

Item Name Quantity

Wood Screw 5 x 35 mm

Toggle Bolt

Top Cabinet Screw 5 x 93 mm

Flat Washer 30 mm diameter

Grommet

Tapping Screw 4 x 8 mm

Exhaust Damper Assembly

Grease Filter

Rear Cushion

Installation Instructions 316902446

Top Template 316902447

Wall Template 316902448

/16"

6 4 2 2 1 4 1 2 1 1 1 1

7 PREPARATION OF THE OVEN

1. Open the bottom of the carton, bend the carton flaps back and tilt the oven over to rest on plastic foam pad. Lift carton off oven and remove all packing materials, Installation Instructions, Wall Template, Top Template, Turntable and Turntable Support; however, DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the ceiling in the oven cavity. SAVE THE CARTON AS IT MAY MAKE INSTALLATION EASIER.

2. CHECK THE OVEN.

Check the oven for any damage, such as misaligned or

bent door, damaged door seals and sealing surfaces, broken or loose door hinges and latches and dents inside the cavity or on the door. If there is any damage, do not operate the oven and contact your dealer or Electrolux AUTHORIZED SERVICER.

Mounting Plate

Figure 5

Use with metal cabinets. Surround the power cord opening. Cut to ﬁ t.

Parts shown not to common scale.

Figure 4

INSTALLATION INSTRUCTIONS

8 VENTILATION SYSTEM

(PREPARING OVEN FOR INSTALLATION)

This Over the Range Microwave Oven is designed for adaptation to three types of hood ventilation systems. Select the type required for your installation.

RECIRCULATING — non-vented, ductless. Follow installation procedure (A). Recirculating requires the use of the Charcoal Filters, which have already been installed in the oven.

HORIZONTAL EXHAUST — outside ventilation. Follow installation procedure (B).

VERTICAL EXHAUST — outside ventilation. Follow installation procedure (C).

(A) RECIRCULATING: NON-VENTED, DUCTLESS OPERATION

The unit is shipped assembled for recirculating.

NOTE:

1. The Exhaust Damper Assembly is not required for recirculating exhaust.

2. The Charcoal Filters should be replaced every 6 to 12 months, depending on use.

Oven Light Cover

Oven Light

(B) HORIZONTAL EXHAUST: OUTSIDE VENTILATION

1. Remove 3 screws from back edge and 5 screws from the top of Fan Cover Bracket. Save 3 screws to use them to attach Exhaust Damper Assembly to the wall later and discard remaining 5. Remove Fan Cover Bracket by sliding it in the opposite direction of the arrow on the Fan Cover Bracket, as shown in Figure 7.

2. Lift Hood Fan Unit carefully and slip wires out of cavity. See Figure 8. CAUTION: Do not pull or stretch Hood Fan

Wire.

3. Rotate the Hood Fan Unit 180˚ so that the Fan Blade Openings are facing the back of the oven. See Figure 9A on page 5.

4. Replace Hood Fan Wire from (A) to (B). See Figure 9B on page 5. Replace Hood Fan Unit into the oven. Be

careful not to pinch the Hood Fan Wire and the Hood Fan Unit. See Figure 9C on page 5.

5. Put the wire back into cavity. See Figure 10A on page 5.

6. Assemble the Exhaust Damper Assembly to the Fan Cover Bracket by sliding it into the slits in the same direction as the arrow. Use 1 Tapping Screw 4 x 8 mm from the INSTALLATION HARDWARE and tighten into place. See Figure 10B on page 5.

7. This assembly will be mounted to the Outside Rear Exhaust cutout in future instructions. See WALL TEMPLATE for further procedures.

Hood Louver

Hood Louver (Inside)

Figure 6A

Charcoal Filters

Fan Cover Bracket

Figure 7

Upper Tab

Hood Fan Unit

Hood Fan Wire

Tabs

Figure 8

Figure 6B

INSTALLATION INSTRUCTIONS

Rotate 180°

Figure 9A

Change the position of wire to left side hole

(B) (A)

Figure 9B

Hood Fan Wire

Figure 9C

Fan Blade Openings

1. Remove and save 3 screws from back edge and 5 screws from the top of the Fan Cover Bracket to use at Step 5. Remove Fan Cover Bracket by sliding it in the opposite direction of the arrow on the Fan Cover Bracket as shown in Figure 11.

2. Lift Hood Fan Unit carefully and slip wires out of cavity. See Figure 12A. CAUTION: Do not pull or stretch Hood Fan Wire.

3. Rotate the Hood Fan Unit 180° so that the Fan Blade Openings are facing the back of the oven. See Figure 12B on page 6. Replace Hood Fan Wire from (A) to (B). See Figure12C on page 6. Then rotate the Hood Fan Unit 90° so that the Fan Blade Openings are facing the top of the oven. See Figure 13 on page 6. Replace Hood Fan Unit into the oven. Be careful not to pinch the lead wire between the inner bracket and the Hood Fan Unit. Put the lead wire into Wire Box.

4. Replace the Fan Cover Bracket by sliding it into the slits in the same direction as the arrow on the Fan Cover Bracket. Make sure the fan blades are visible through the top openings in the oven before proceeding. See Figure 14 on page 6.

5. Attach the Fan Cover Bracket to unit with the 3 screws from back edge and 4 screws except screw(A) from the top of the Fan Cover Bracket, which were removed at Step 1 above. See Figure 14 on page 6. Screw (A) will be used at MOUNTING OVEN THE WALL Step5 on page 7. The Hood Fan Unit is now rotated for vertical exhaust operation.

6. Attach the Exhaust Damper Assembly to the fan cover bracket on the top of the outercase cabinet after mounting the oven. To attach the Exhaust Damper Assembly, refer to MOUNTING OVEN TO THE WALL, See Figure 20 on page 7 and TOP CABINET TEMPLATE.

Exhaust Damper

Assembly

Fan Cover Bracket

Save the assembly for

future instructions.

Oven Rear Side

Figure 10A

Figure 10B

Wall Side

Rear Cushion

Apply Rear Cushion

after Exhaust Damper

Assembly is screwed

to wall.

Hood Fan Wire

(A)

Fan Cover Bracket

Figure 11

Hood Fan Unit

Figure 12A

INSTALLATION INSTRUCTIONS

Rotate 180°

Change the position of wire to left side hole

(A) Rotate 90°

Figure 12B

(B) (A)

Figure 12C

(B)

Fan Blade Openings

NOTE: THIS OV EN SHOULD BE ATTACHED TO AT LEAST ONE WALL ST UD.

MOUNTING PLATE

1. Separate Toggle Nuts, packed in the INSTALLATION HARDWARE, from 4 Toggle Bolts.

IMPORTANT

to Use wood screws to attach mounting plate to the stud or studs. Use Toggle Bolts to attach mounting plate through the holes at A, B, C and D UNLESS THOSE HOLES ARE LOCATED ON THE STUD. Insert one Toggle Bolt into A, B, C and D where appropriate (these correspond to holes of the Wall Template) and put the Toggle Nuts onto the Toggle Bolts. See Figure

15. Refer to instructions in Wall Template.

3. Position the Mounting Plate with the Toggle Bolts attached at the wall location and insert Toggle Nuts and Bolts through the holes in the wall with the Toggle Nuts closed. See Figure

16. Use Wood Screws to attach the Mounting Plate to studs.

NOTE: Before insertion, be sure you leave a space more than

the thickness of the wall between the Mounting Plate and the end of each of the Toggle Nuts (in the closed position). If you do not leave enough space, the Toggle Nut will not be able to open on the other side of the wall. Also, once a Toggle Nut opens, it cannot be withdrawn from the hole; therefore make sure all of the Toggles are in the correct position before insertion.

4. Align the Mounting Plate carefully and hold in position while tightening Toggle Bolts. Pull Toggle Bolt toward

you and turn clockwise to tighten. See Figure 17.

Use the mounting template provided

SUITABLE FOR USE ABOVE GAS OR ELECTRICAL COOKING EQUIPMENT 36 INCHES OR LESS WIDE WARNING TO REDUCE THE RISK OF FIRE AND ELECTRICAL SHOCK,INSTALL AT LEAST 13-3/16 INCHES ABOVE A RANGE (OR COOK TOP)

Figure 13

(A)

Figure 14

9 OVEN INSTALLATION

THIS OVEN CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING INST RUCTIONS FOUND ON BOTH TEMPLATES.

THE NEXT STEP IS TO READ AND FOLLOW MOUNTING INFORMATION ON BOTH TOP CABINET A ND WALL T EMPL ATES.

Tog gle Bolt

Mounting Plate

Tog gle N ut

Figure 15

Space more

than wall

thickness

Figure 17

Wall

Figure 16

INSTALLATION INSTRUCTIONS

MOUNTING OVEN TO THE WALL

Two people are recommended to attach the Microwave Oven/ Hood to the Mounting Plate.

1. Thread the power supply cord through the hole made in the bottom of the top cabinet.

2. Install the oven by tilting it forward and sliding it onto two tabs of the Mounting Plate. Rotate the oven up so it rests against the wall. See Figure 18 on page 7.

3. Use the two Top Cabinet Screws and two Flat Washers, supplied in the INSTALLATION HARDWARE, to attach the unit to the top cabinet. See Figure 19 on page 7.

4. Secure the bottom of the oven to the Mounting Plate by using two Tapping Screws 4 x 8 mm from the INSTALLATION HARDWARE. See Figure 19 on page 7.

5. (For Vertical Exhaust Only)

Attach the Exhaust Damper Assembly to the fan Cover

Bracket on the top of the outercase cabinet by sliding it into the slits in the same direction as the allow using screw (A) which removed at (C) VERTICAL EXHAUST STEP 1 on page 5. See Figure 20 on page 7.

Tapping Screw (A)

Figure 20

CHECKLIST FOR INSTALLATION

1. Make sure the unit has been installed according to all of the Installation Instructions and the Wall and Top Cabinet Templates.

2. Plug in the power cord.

3. Keep these Installation Instructions.

Figure 18

Top Cabinet Screws

Flat Washers

Tabs

NOTE:

Make sure to remove the tape at the turntable support before operation. See ﬁ gure 21.

Remove this tape before operation.

Figure 21

Tapping Screws

Figure 19

NOTES

TINSKA038WRRZ-EL01

Rear Cushion

Apply Rear Cushion

Rear Cushion

Assembly is screwed

after Exhaust Damper

to wall.

+ 16 hidden pages