Frigidaire CAHE8ERR410A17, CAHE8ERR410A14, CAHE8ERR410A15, CAHE12ERR410A14, CAH12ECR20 Installation Guide

...
READ BEFORE INSTALLING UNIT
For SLO3 Air Conditoner (8,000-12,000 BTU)
* Carefully read the installation manual before beginning. :_ Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended period of time. Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
Tools and Parts:
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
TOOLS NEEDED
Flat-blade and Phillips screwdrivers Tape measure
Level Drill and 3/16", 1/8", 3/32", or smaller drill bit
Through-the-wall Installation:
In addition to the tools listed above, the following tools are needed for through-the-wall installation.
TOOLS NEEDED
saw ® caulk
® 1" (2.5 cm) or thicker lumber
Parts Supplied: Check that all parts are included in parts package:
Hardware
#10 X 1/2" pan - head
Phillips screws
#10 X 1/2" round - head
screws
#10 X 1/4" pan - head
Phillips screws
Qty. Hardware
3 Top channel
7 J Window sash seal
5 Foam seal
e #10 X 1"wood screws (7)
Qty.
I
I
I
side curtains
window lock bracket
2 Safety Lock
,, (for Vinyl-Clad window)
weather seals
(6"X314"X1112")
I
2
5
2020213A1640
Installation parts are supplied for double-hung windows up to 36" (91.4 cm) wide. A special Wide Window Kit is available from your dealer or service center. See "Accessories."
Do not use any screws other than those specified here.
Location Requirements: IMPORTANT:Observe all governing codes and ordinances. Check the location where air conditioner will be installed.
Proper installation is your responsibility. Make sure you have everything necessary for correct installation.
Grounded electrical outlet within 4 ft (122 cm) of where the power cord exits the air conditioner.
Free movement of air in room to be cooled. A large enough opening for the air conditioner. Adequate wall support for weight of air conditioner. Air conditioner weights between 70 and 85 Ibs (32 to 40 kgs).
Window Installation: Window opening measurements (FIG.2) :
26-7/8" to 36" (68.3 cm to 91.4 cm) opening width.
16-1/2" (41.9 cm) minimum opening height.
FIG.1 FIG.2
B
E r'
A. Cabinet louvers
Remove packaging material:
Remove and dispose of/recycle packaging materials. Remove tape and glue residue from surfaces before installing the air conditioner. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your air conditioner.
Handle the air conditioner gently.
t. Remove the air conditioner from the carton and place it on cardboard.
2. Remove 1 shipping screw from each side of the cabinet (FIG.3A).
3. Remove front panel by removing t Phillips screw from each side of the front panel. Set screws aside and save (FIG.3B).
4. Rotate Front Panel up until top tabs are free. Pull panel straight out. Depress latch on electronics plug (on some models) to disconnect. Remove Front Panel from unit (see Fig. 4).
5. Pull on the handles to slide the air conditioner out of the cabinet. Place the air conditioner on cardboard (FIG.5).
A. 26-7/8" (68.3 cm) minimum
B. 16-112" (41.9 cm) minimum
Loading...
+ 4 hidden pages