Frigidaire CDE7300RW0, CDE7400QW0, CDE7400QW1, CDG7300RW0, CDG7400QW0 Installation Guide

...

TABLE OF CONTENTS

Important Safety Instructions ........................... 2-3 Accessories .................................................... 24

Installatton Requirements .............................. 4-11 Fran_als ........................................................... 25

Installatton Instructions ................................ 12-19 Espa_ol ........................................................... 49

Reversmg Door ............................................ 20-23

c:_

For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent

property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in

....the vidnity °f th!s °! any °ther app!!ance:......................................................................................................................................................................................................................................................................................................................

AWARNING - RISK OF FIRE

Read all of the following instructions before installing and using this appliance:

* Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play. Cartons covered

with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a garbage container or make materials inaccessible to children.

* Clothes dryer installation and service must be performed by a qualified installer, service agency or the gas supplier. * Install the clothes dryer according to the manufacturer's instructions and local codes.

* The electrical service to the dryer must conform with local codes and ordinances and the latest edition of the

National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical code C22.I part 1.

* The gas service to the dryer must conform with local codes and ordinances and the latest edition of the National

Fuel Gas Code ANSI Z223.1, or in Canada, CAN/ACG BI49.1-2000. An individual manual shut-off valve must be installed within 6 ft (i.83 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

* The dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. i!2 (latest editions) for HONE

USE only. This dryer is not recommended for commercial applications such as restaurants, beauty salons, etc.

* Do not install a clothes dryer with flexible plastic or flexible foil venting material. Flexible venting materials are

known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase

the risk of fire.

* Do not stack a dryer on top of washer already installed on pedestal. Do not stack dryer on top of another dryer.

Do not stack washer on top of dryer. Do not stack washer on top of another washer. Do not stack dryer on top of

washer without use of manufacturer approved and correctly installed stacking kit appropriate for your model.

* The instructions in this manual and all other literature included with this dryer are not meant to cover every

possible condition and situation that may occur. Good safe practice and caution NUST be applied when installing,

operating and maintaining any appliance.

WHAT TO DO IF YOU SMELL GAS:

* Do not try to light any appliance. * Do not touch any electrical switch; do not use any

phone in your building. * Clear the room, building or area of all occupants. * Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions. * If you cannot reach your gas supplier, call the fire

department.

person move or lift the applianc e, ............

Save these instructions

for future reference.

Tools and materials needed for installation:

Pre-Installation Requirements

* Adjustable pliers * Carpenter's level * Phillips, straight, & square bit * External vent hood

screwdrivers * 4-inch (!02 mm), rigid metal or * Adjustable wrench semi-rigid metal exhaust duct work * Pipewrench for gas supply (gas * 3-wire or 4-wire 240 volt cord kit

dryer) (electric dryer) * @-resistant thread tape (for natural * 4 in. (!02 mm) clamp

gas or LPsupply, gas dryer)

* Gas line shutoff valve (gas dryer) * _/2NPTunion flare adapters (x2)

and flexible gas supply line (gas dryer) Netal foil tape (not duct tape)

Pleasereadallinstructionsbeforeusingthisdryer.

Exhaust Venting

Free-flowing, clear of lint buildup

4 inch (102 mm) rigid or semi-rigid ducting of

Recognize safety syrnboisr words and labels

Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described below:

Definitions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury

or death.

DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury, 240v Electric Supply (Electric Dryer)

CAUTION indicates a potentially hazardous situation E3 Test hinge and latch for function which, if not avoided, may result in minor or moderate

injury. Electrical Power

IMPORTANT indicates installation, operation or maintenance information which is important but not hazard-related.

minimal length and turns

E_ NO foil or plastic venting material E_ Approved vent hood exhausted to outdoors

Leveling

E_ Dryer is level, side-to-side and front-to-back E3 Cabinet is setting solid on all corners

GasSupplyCGasDryer:

E_ Manual shutoff valve present in supply E_ AIt connections sealed with approved sealer and

wrench tight E_ Conversion kit for LPsystem E_ Gas supply turned on E3 No leaks present at all connections -

check with soapy water, NEVERcheck with flame

E3 Approved NEMA 10-30R or 14-30R service cord

with all screws tight on terminal block E3 Approved strain relief installed

E3 Terminal access cover installed before initial

operation

Door Reversal

E3 Follow detailed instructions in this guide

E3 House power turned on E3 Dryer plugged in

Final Checks

Installation Instructions and Use and Care Guide read thoroughly

Door latches and drum tumbles when cycle

starts

Registration card sent in

Becauseofpotentiallyinconsistentvoltagecapabilities,theuseofthisdryerwithpowercreatedbygaspowered generators,solarpoweredgenerators,windpoweredgeneratorsoranyothergeneratorotherthanthelocalutility

companyisnotrecommended,

Electrical requirements for electric dryer

CIRCUIT - Individual 30 amp. branch circuit fused with 30 amp. time delay fuses or circuit breakers. Use separately

fused circuits for washer and dryer. DO NOT operate a washer and a dryer on the same circuit.

POWER SUPPLY- 3-wire or 4-wire, 240 volt, single phase, 60 Hz, Alternating Current.

through the neutral.

OUTLET RECEPTACLE- NEMA 10-3ORor NEMA 14-30R rece )tacie to be located so the power supply cord is accessible

when the dryer is in the installed position.

GROUNDING CONNECTION - See "Grounding requirements" in Electrical Installation section.

3-WIRE POWERSUPPLYCORDKIT (not supplied)

3-wire receptacle

(NEMA type 10-30R)

The dryer MUSTemploy a 3-conductor power supply cord NEMA 10-30 type SRDTrated at 240

volt AC minimum, 30 amp, with 3 open end spade

lug connectors with upturned ends or closed loop connectors and marked for use with clothes

dryers. For 3-wire cord connection instructions see

ELECTRICALCONNECTIONS FOR A 3-WIRE SYSTEM.

4-WIRE POWER SUPPLYCORD KIT (not supplied)

4-wire receptacle

(NEMA type 14-30R)

The dryer MUST employ a 4-conductor power supply cord NEMA 14-30 type SRDTor ST (as required) rated

at 240 volt AC minimum, 30 amp, with 4 open end spade lug connectors with upturned ends or closed loop connectors and marked for use with clothes

dryers. For 4-wire cord connection instructions see ELECTRICALCONNECTIONS FORA 4-WIRE SYSTEM.

Electrical requirements for gas dryer

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2-wire, with ground, !20 volt, single

phase, 60 Hz, Alternating Current.

POWER SUPPLYCORD - The dryer is equipped with a 120

volt 3-wire power cord.

GROUNDING CONNECTION - See "Grounding

requirements" in Electrical Installation section.

Gas supply requirements

; EXPLOSION HAZARD

Uncoated copper tubing will corrode when subjected to natural gas, causing gas leaks. Use ONLY black iron, stainless steel, or plastic-coated brass piping for gas

supply.

1 Installation MUST conform with local codes, or in

the absence of local codes, with the National Fuel Gas Code, ANSI Z223.I (latest edition).

2 The gas supply line should be 1/2 inch (1.27 cm)

pipe.

3 If codes allow, flexible metal tubing may be used

to connect your dryer to the gas supply line. The tubing MUST be constructed of stainless steel or

plastic-coated brass.

Groundingtype

wal receptacle

/ _.\ I |anycircurnstances

_- Do not,under -"

\ I_ grounding prong.

B-pronggroundedpl

4. The gas supply line MUSThave an individual shutoff valve installed in accordance with the

B!49.!, Natural Gas and Propane Installation Code.

5 A !/8 inch (0.32 cm) N.P.T.plugged tapping,

accessible for test gauge connection, MUST be installed immediately upstream of the gas supply

connection to the dryer.

6 The dryer MUSTbe disconnected from the gas

supply piping system during any pressure testing of the gas supply piping system at test pressures in

excess of !/2 psig (3.45 kPa).

7 The dryer MUSTbe isolated from the gas supply

piping system during any pressure testing of the gas supply piping system at test pressures equal to

or tess than Z/2 psig (3.45 kPa).

8 Connections for the gas supply must comply with

the Standard for Connectors for Gas Appliances, ANSI Z21.24.

Exhaust system requirements

Use only 4 inch (i02 mm) diameter (minimum) rigid or flexible metal duct and approved vent hood which

has a swing-out damper(s) that open when the dryer is in operation. When the dryer stops, the dampers automatically close to prevent drafts and the entrance of insects and rodents. To avoid restricting the outlet,

maintain a minimum of !2 inches (30.5 cm) clearance between the vent hood and the ground or any other

obstruction.

Failure to follow these instructions can create excessive

FIRE HAZARD

drying times and fire hazards.

The following are specific requirements for proper

and safe operationofyour dryer,

FIRE HAZARD

Do not install a clothes dryer with flexible plastic or metal foil venting materials. Flexible venting materials

are known to collapse, be easily crushed and trap tint. These conditions witt obstruct clothes dryer airflow and

increase the risk of fire.

If your present system is made up of plastic duct or metal foil duct, replace it with a rigid or semi-rigid metal

duct. Also, ensure the present duct is free of any lint prior to installing dryer duct.

Correct Incorrect

Correct

Exhaust system requirements, continued

FIRE HAZARD FIRE HAZARD

A clothes dryer must be exhausted outdoors• Do not Exceeding the length of duct pipe or number of elbows exhaust dryer into a chimney, a wall, a ceiling, an attic, allowed in the "MAXIMUM LENGTH" charts can cause

a crawl space or any concealed space of a building• A an accumulation of lint in the exhaust system• Plugging

clothes dryer produces combustible lint. If the dryer is not exhausted outdoors, some fine lint will be expelled

into the laundry area• An accumulation of tint in any area of the home can create a health and fire hazard.

The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and in the surrounding area.

FIRE HAZARD

Do not allow combustible materials (for example: clothing, draperies/curtains, paper) to come in contact with exhaust system. The dryer MUST NOT be exhausted into a chimney, a wall, a ceiling, or any concealed space of a building which can accumulate lint, resulting in a fire hazard.

Do not screen the exhaust ends of the vent system, or use any screws, rivets or other fasteners that

extend into the duct to assemble the exhaust system. Lint can become caught in the screen, on the screws or rivets, clogging the duct work and material.

creating a fire hazard as welt as increasing drying

..... * If nsta ngsem-rgdventng do not exceed8ft

t mes Use an approved vent hood to term nate the "2 4 m" duct len th

• _. ) g •

duct outdoors, and seal all ]omts wtth metal fotl duct .....

tape, All male duct pipe fittings MUST be instalied downstream with the flow of air.

the system could create a fire hazard, as welt as increase drying times.

MAXIMUM LENGTH

of 4" (102mm) RigidMetal Duct

9 VENT HOOD TYPE

0 64 ft. (19.5 m) 48 ft. (14.6 m)

1 52 ft. (15,9 m) 40 ft, (12.2 m) 2 44 ft. (13,5 m) 32 ft, (9.8 m) 3 36 ft. (11 m) 24 ft. (7.3 m) 4 28 ft. (9,5 m) 16 ft, (4.9 m)

(Preferred)

4" 2.5"

(102ram) Iouvered (6.35cm)

o Do not install flexible plastic or flexible foil venting

Exhaust system requirements, continued

Install male fittings in correct direction:

CORRECT INCORRECT

In installations where the exhaust system is not described in the charts, the following method must be used to

determine if the exhaust system is acceptable:

:1. Connect an inclined or digital manometer between

the dryer and the point the exhaust connects to the dryer.

2 Set the dryer timer and temperature to air fluff

(cool down) and start the dryer.

3 Read the measurement on the manometer. 4 The system back pressure MUST NOT be higher

than 0.75 inches of water column. If the system back pressure is tess than 0.75 inches of water column, the system is acceptable. If the

manometer reading is higher than 0.75 inches of

water column, the system is too restrictive and the

installation is unacceptable.

Although vertical orientation of the exhaust system is acceptable, certain extenuating circumstances could

affect the performance of the dryer:

• Only rigid metal duct work should be used.

• Venting vertically through a roof may expose the exhaust system to down drafts causing an increase

in vent restriction.

• Running the exhaust system through an

uninsulated area may cause condensation and

faster accumulation of lint.

• Compression or crimping of the exhaust system will cause an increase in vent restriction.

• The exhaust system should be inspected and cleaned a minimum of every 18 months with

normal usage. The more the dryer is used, the more often you should check the exhaust system

and vent hood for proper operation.

Exhaust direction

Directional exhausting can be accomplished by installing

a quick-turn 90 ° dryer vent elbow directly to exhaust outlet of dryer. Dryer vent elbows are available through

your local parts distributor or hardware store.

See also Clearance Requirements on the next page.

Use of 90 ° quick-turn elbow is required to meet

minimum installation depth of free-standing

dryer.

Manufactured or mobile home installation

1 Installation MUST conform to current Manufactured

Home Construction & Safety Standard, Title 24 CFR, Part 32-80 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24,

HUD Part 280) or Standard CAN/CSAZ240 MH.

2 Dryer MUST be exhausted outside (outdoors, not

beneath the mobile home) using metal ducting that wilt not support combustion. Metal ducting

must be 4 inches (10.i6 cm) in diameter with no obstructions. Rigid metal duct is preferred.

3 If dryer is exhausted through the floor and area

beneath the mobile home is enclosed, the exhaust

system MUST terminate outside the enclosure with the termination securely fastened to the mobile

home structure.

4 Refer to previous sections in this guide for other

important exhaust venting system requirements.

5 When installing a gas dryer into a mobile home, a

provision must be made for outside make up air. This provision is to be not less than twice the area

of the dryer exhaust outlet.

6 Installer MUST anchor this (:!_)dryer or (2) dryer

mounted on pedestal to the floor with approved Mobile Home Installation Kit - P/N :!_37067200,

Clearance requirememts

i i iiiiiiiii!ii!i iiii ii i ___________________________________________________________________:__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ii ¸,......................................................................................................................................................................................................................

E×PLOSlON HAZARD DO NOT INSTALLYOUR DRYER:

Do not install the dryer where gasoline or other 1 In an area exposed to dripping water or outside flammables are kept or stored. If the dryer is installed weather conditions.

in a garage, it must be a minimum of 18 inches (45.7 cm) above the floor. Failure to do so can result in 2 In an area where it will come in contact with

death, explosion, fire or burns, curtains, drapes, or anything that will obstruct

the flow of combustion and ventilation air.

3 On carpet. Floor MUST be solid with a maximum

Clearance requirements, continued

Installation in a Recess or Closet

:1. A dryer installed in a bedroom, bathroom, recess or

closet, MUST be exhausted outdoors.

2 No other fuel burning appliance shall be installed in

the same closet as the gas dryer,

I 3 Your dryer needs the space around it for proper

ventilation.

DO NOT install your dryer in a closet with a solid door,

4 Closet door ventilation required: A minimum

of 120 square inches (774.2 cm 2) of opening, equally divided at the top and bottom of the door, is required, Openings should be located 3

inches (7,6 cm) from bottom and top of door. Openings are required to be unobstructed when a door is installed, A Iouvered door with equivalent air openings for the full length of the door is acceptable.

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0" (0 cm) 0" (0 cm)* 0" (0 cm) n/a Under- 0" (0 cm) 0" (0 cm)* 0" (0 cm) n/a

Counter Closet 0" (0 cm) 0" (0 cm) _ 0" (0 cm) 1" (2.5 cm)

* For other than straight back venting, a quick-turn 90 °

dryer vent elbow (vented right or down in free-standing dryer or right on pedestal-mounted dryer) must be

installed to achieve 0" (0 cm) installation.

0, -=-_, ,-_-=-

o :0!:,:,j

(2S4cm) (Ocm_

closet door

Toachieve an installation with O"(0 cm) clearance for the back of the dryer (for other than straight back

venting), a quick-turn 90 ° dryer vent elbow must be

!nsta!!ed as descr!bed prev!ous!y !n th!s manua!. ...................................

i!!i!i!l!_!0 ill

Dryer Dimensions

_ 51.4" (131 cm)*

o clear open door 41_ 30.3" (77 cm)*

freestand dryer

on floor

floorline

dryer mounted on

optional pedestal

floorline

51.4" (t31 cm) _

to clear open door

to front of c osed door

30.3" (77 cm)*

to front of closed door

27.0"

(68.5 cm)

'T o

"n)" gas supply " "

of gas unit

pipe on rear

- - - i....................................-

_!' (9.5 cm) t OeCaen;ernt f

27,0"

(68.5 cm_

71.5"

(182 cm)

water supply connection on

rear of unit

gas supply pipe on rear of gas unit

electrical supply on

r_f unit _

centefline height for

rear vent

19.0"

(48;m)

electrical supply on rear of unit'

height for

floor]ine

*Connection of water inlet hose on steam dryer adds 3/4 in. (2 cm) to installation depth.

1Power supply cord length on gas dryer approximately 60 inches (152.5 cm).

2Drain hose length on washer approximately 59 inches (150 cm).

3Power supply cord length on washer approximately 60 inches (152.5 cm).

37"

(94 cm)

39"

(99 cm)

Electrical installation The following are specific requirements for proper and

safe electrical installation of your dryer. Failure to follow

* This appliance MUST be properly grounded.

ELECTRICAL SHOCK HAZARD

Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the

amounts of electrical current this dryer utilizes and can melt, creating electrical shock and/ or fire hazard. Locate the dryer within reach of

the receptacle for the length power cord to be

purchased, allowing some slack in the cord. Refer to the pre-instaltation requirements in this manual for the proper power cord to be purchased.

Grounding requirements - Electric dryer (USA)

conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

For a grounded, cord-connected dryer:

1 The dryer MUST be grounded. In the event of a

malfunction or breakdown, grounding witl reduce

the risk of electrical shock by a path of least

resistance for electrical current.

2 After you purchase and install a 3 wire or 4 wire

power supply cord having an equipment-grounding

conductor and a grounding plug that matches you

* A U.L.-approved strain relief must be installed onto

Fora permanently connected dryer:

ELECTRICAL SHOCK HAZARD

power cord. If the strain relief is not attached, the

cord can be pulled out of the dryer and can be cut

by any movement of the cord, resulting in electrical

shock.

Do not use an aluminum wired receptacle with a copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and

aluminum and can cause electrical shorts. The

proper wiring and receptacle is a copper wired power cord with a copper wired receptacle.

wiring system, the plug MUST be plugged into an appropriate, copper wired receptacle that is

properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a

licensed electrician.

3 DO NOT modify the plug you've installed on this

appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

1 The dryer MUSTbe connected to a grounded

metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit

conductors and connected to the equipment- grounding terminal or lead on the appliance.

Grounding requirements - Electric dryer (Canada)

2 Since your dryer is equipped with a power supply

cord having an equipment-grounding conductor and a grounding plug, the plug must be plugged into

an appropriate outlet that is property installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician.

3 DO NOT modify the plug provided with this

For a grounded, cord-connected dryer:

appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

1 The dryer MUST be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance

for electrical current.

Grounding requirements = Gas dryer (USA and Canada)

1 The dryer is equipped with a three-prong

(grounding) plug for your protection against shock

hazard and should be plugged directly into a properly grounded three-prong receptacle.

2 The plug must be plugged into an appropriate

outlet that is properly installed and grounded in accordance with all local codes and ordinances. Tf

in doubt, call a licensed electrician.

3 DO NOT modify the plug provided with this

appliance. Tf it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Grounding lype watl receptacle

anycircumstances,

Do not, under

nding prong, j

P_vercordwith _

3-prong grounded plug _

Gas connection

1 Remove the shipping cap from gas pipe at the rear 3 Open the shutoff valve in the gas supply line to

of the dryer, allow gas to flow through the pipe. Wait a few

DO NOT connect the dryer to LP, gas service without converting the gas valve. An L.P.conversion kit must be installed by a qualified gas technician.

2 Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or

approved pipe from gas supply line to the 3/8 inch (0.96 cm) pipe located on the back of the dryer.

Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm) reducer for the connection. Apply an approved

thread sealer that is resistant to the corrosive action of liquefied gases on all pipe connections.

minutes for gas to move through the gas line.

Open position

Manua GAS FLOW "_ Shutoff Flare _ Flare |

Valve Union Union |

,o_/:_ed:l_Fi_'_i l\':_:::l_:_\\_/_'i l_/

: ,1_I t ' t t [

\. Nipple Flexible Inlet Pipe on | Open Connector Back of Dryer |

AHconnections must be wrench-tightened J

The supply line must be equipped with an approved

manual shutoff valve. This valve should be located in the same room as the dryer and should be in a location that allows ease of opening and closing. Do not block

access to the gas shutoff valve.

4 Check for gas system leaks with a manometer. If a

manometer is not available, test all connections by

brushing on a soapy water solution.

EXPLOSION HAZARD

.EwRtestforgasleakswithanopen,ame.

Water connection (Steam Model only)

WATER SUPPLY REQUIREMENTS

Cold water faucet MUST be installed within 42 inches (i07 cm) of your dryer's water inlet. The faucet MUST be

3/4 inch (1.9 cm) with threading for laundry hose con- nection. Water pressure MUST be between 30 and 120

psi. Your water department can advise you of your water pressure.

1 Turn off COLD water supply to washer. 2 Remove COLD inlet hose from COLD water supply

and inspect for rubber washer. Replace washer if it

is torn or worn out,

RUBBER WASHER

MUST BE PRESENT

AND UNDAMAGED y

COLD INLET HOSE

TO WASHER

3 Momentarily turn on COLDsupply and run some

water into a bucket or container to clear any contaminants in the line.

4 Remove hose kit from dryer drum and inspect hose

couplings for proper placement of rubber washers.

RUBBER WASHERS MUST BE PRESENT

Water connec|:ion, continued (Steam Model only)

5 If your installation has room for the COLD water

supply to accept the "Y" connector directly, thread the "Y" connector to the COLD water supply and

snug it by hand; then tighten it another 2/3 turn with pliers.

ilIfyouwereab,etoinsta,,theYconnectordirect,ytoiii

the COLD water supply, please skip to step 8.

6 If there is not room to install the "Y" connector

directly, thread a short extension hose on to the COLD water supply and snug it by hand; then tighten it another 2/3 turn with pliers,

DIRECT CONNECTION

i-_ _ / WATERINLET

_'% / ON DRYER

WiTHEXTENSION*

supplier. Extension hose must meet qualifications for use in laundry installation.

7 Thread the "Y" connector to the short extension

hose and snug it by hand; then tighten it another

2/3 turn with pliers.

8 Connect the COLD inlet hose for the washer to the

"Y" connector and snug it by hand; then tighten it another 2/3 turn with pliers,

9 Connect the straight end of the tong hose from the

kit to the other outlet on the "Y" connector and

snug it by hand, Connect the hose's 90° coupling to the brass water inlet on the back of the dryer and

snug it by hand. Tighten each connection of the dryer inlet hose another 2/3 turn with pliers.

10 Turn on the water and check for leaks at all

connections.

COLD WATER SUPPLY

HOSETO WASHER

*Laundry hose extensionnot includedwith dryer,

/ j

Electrical connection (non=Canada) - 3 wire cord

3-wire receptacle

(NEMA type 10-30R)

could result in personal injury or even death.

1 Turn off power supply to outlet. 2 Remove the screw securing the terminal block

access cover in the lower corner on the back of the dryer.

3 Install a UL-approved strain relief according to the

power cord/strain relief manufacturer's instructions in the power cord entry hole below the access

panel. At this time, the strain relief should be loosely in place.

4 Thread an UNPLUGGED,UL-approved, 30 amp.

power cord, NEMA 10-30 type SRDT, through the

strain relief.

5 Attach the power cord neutral (center wire)

conductor to the SILVERcolored center terminal on the terminal block. Tighten the screw securely.

6 Attach the remaining two power cord outer

conductors to the outer, BRASScolored terminals on the terminal block. Tighten both screws securely.

Do not make a sharp bend or crimp wiring/conductor at connections.

7 Follow manufacturer's guidelines for firmly securing

the strain relief and power cord.

8 Reinstall the terminal block cover.

If moving dryer from a 4-wire system and installing it in a 3-wire system, move the internal ground from the center terminal back to the GREENscrew next to the

terminal block.

_-_ Accesscover

f_ black

If a terminal screw falls during cord installation, it can be retrieved in the terminal screw recovery slot below

Line 2

(BRASS terminal)

Neutral

(SILVER terminal)

Line 1

(BRASS terminal)

-_ Internal ground (GREEN screw)

Install

UL-approved

strain relief here

Terminal screw

recovery slot

the access panel.

DO NOT remove

internal ground in terminal

a 3-wire system]!

Neutral

Electrical connection (non=Canada) = 4 wire cord

4-wire receptacle

(NEMA type 14-30R)

1 Turn off power supply to outlet. 2 Remove the screw securing the terminal block

access cover in the lower corner on the back of the dryer.

3 [nstall a UL-approved strain retief according to the

power cord/strain relief manufacturer's instructions in the power cord entry hole below the access paneh At this time, the strain relief should be loosely in place.

4 Thread an UNPLUGGED,UL-approved, 30 amp.

power cord, NEMA 14-30 type ST or SRDT,through

the strain relief.

5 Disconnect the internal (WHZTE) dryer harness

ground wire from the (GREEN) ground screw next to the terminal block.

6 Attach the ground (GREEN) power cord wire to the

cabinet with the ground (GREEN) screw. Tighten the screw securely.

7 Move the internal dryer harness ground (WHZTE)

wire to the terminal block and attach it along with the neutral (WHZTE) power cord wire conductor to the center, SILVERcolored terminal on the

terminal block. Tighten the screw securely.

8 Attach the RED and BLACKpower cord conductors

to the outer, BRASScolored terminals on the terminal block. Tighten both screws securely.

Do not make a sharp bend or crimp wiring/conductor at connections.

9 Follow manufacturer's guidelines for firmly securing

the strain relief and power cord.

10 Reinstall the terminal block cover.

If a terminal screw falls during cord installation, it can be retrieved in the terminal screw recovery slot below

the access panel. ................

__ _r_Neutra]

t_"1_; 30AMP _%' )-_Ground. t(wH'TE w're)

T NEMA 14-30 4@_ /(GREEN w:re)l

(SILVER terminal)

Line 1

(BRASS terminal)

"_ Internal ground

(GREEN screw)

recoveryslot

Move internal ground (WHITE) Neutral

wire to neutral (SILVER) terminal

terminal for 4-wire !

',C"?

ground screw

GREEN BLACK

ground wirl

neutral wire

RED power win

General installation

1 Connect the exhaust duct to the outside exhaust

system. Use of a 4" (102 ram) clamp (item A) is

recommended to connect the dryer to the exhaust vent

system. Use metal foil tape to seal all other joints.

2 Use a carpenter's level to level your dryer front-to-back

and side-to-side.

3 Use adjustable pliers to adjust the leveling legs so the

dryer is level front-to-rear and side-to-side, and stable corner-to-corner.

4 Pressdown on alternate corners and sides and feel for

the slightest movement. Adjust the appropriate leg(s) so the dryer sits solidly on the floor on ALL four legs,

Keepthe leveling leg extension at a minimum for best performance of the dryer,

before plugging the power cord into an outlet. ........

5 Plugthe power cord into a grounded outlet.

Groundinc

Do not, und any circumstances,

| grounding prongj)

3,prong grounded plug

6 Turn on the power at the circuit breaker/fuse box. 7 Read the Use & Care Guide provided with the dryer. It

contains valuable and helpful information that will save you time and money.

8 If you have any questions during initial operation,

please review the "Avoid Service Checklist" in your Use

& Care Guide before calling for service.

9 Placethese instructions in a location near the dryer for

future reference.

Removing the door

1 Protect fiat work surface, such as top of dryer or 4

floor near dryer, with a soft cloth or towel.

2 Open dryer door and remove the two hinge screws. 5

Remove lower screw first, then upper screw.

iil _i

i i il i _i!

il i i i i

iii !

i i!"

, i _ _ _i _

3 Supporting door with both hands, squarely lift door

and hinge upward approximately 3/8" (10 mm) so "T" post on back of hinge can slide out through "T" slot on front panel.

"T" SLOT IN FRONT PANEL

POSTON

DOORHINGE

Gently place dryer door face down on fiat, covered work surface.

Locate the 5 indented head screws (no. 1-5) in the small, circular recesses (at 1i, 1, 4, 6, and 8 o'clock

positions) of the inner door. Remove and save these 5 screws.

5 4

...............................................................

6 Locate the 2 pan head screws (no. 6-7) on the

inner door nearest the metal strike and center of hinge (9 and 3 o'clock positions). Remove and save

these 2 screws.

7 Separate inner door assembly from outer door

assembly.

Reversing the hinge

1 Carefully pull out the 2 small round hole plugs from

the front panel and save. Remove and save the square "T" slot cover by sliding it up and pulling

it out. Move all 3 plugs to the opposite side of the

front )anel and insert.

ROUNOPwG.

_SQUARE PLUG ...___

_ROUND PLUG_

2 Turn inner door assembly over to expose retaining

tabs of metal strike. Grip tabs fully with pliers to

remove. Discard old metal strike.

3 Turn the inner door assembly back over and locate

the 2 pan head hinge screws. Remove and save the 2 screws and separate the hinge from inner door

assembly.

HINGE SCREWS

4 From the back side of the inner door, pinch the

retaining tabs of the plastic square plug to release it. Save square plug for reinstallation.

5 Carefully remove the 2 round plugs from the inner

door and move them to the opposite holes and reinstall.

OUT

6 Rotate the hinge and move it to the opposite side

of the inner door. Attach it with the 2 pan head screws removed previously. Reinstall plastic plug in the square hole next to the hinge.

Reassembling the door

1 Lift the inner glass ring, Rotate it i80 degrees,

reinstall on outer door, lining up indicators - "LH"

for left-hand hinge or "RH" for right-hand hinge.

3 Replace indented head screws (no, i-5) removed

earlier. Take care not to strip out the plastic holes.

4 Replace pan head screws (no. 6-7) removed earlier.

Take care not to strip out the plastic holes.

2 Rest the opening of the inner door at a 90 degree

angle on the supports for the hinge cutout cover.

Pivot the inner door down onto the outer door.

4 /

Locate new metal strike supplied with dryer manuals, Grip new strike with pliers as shown

below. Firmly insert the strike so it is oriented vertically,

+ 51 hidden pages