Frigidaire FAZ08HS1AA, FAZ08HS1AB, FAZ12HS2AA, FAZ12HS2AB Installation Guide
INSTALLATIONINSTRUCTIONS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Took Needed
[] Flat=blade and Phillips [] Tape measure
screwdrivers
[] Level
Through=the=Wall Installation:
In addition to the tools listed above, the following tools are
needed for through-the-wall installation,
[] Saw [] l"(2.5cm) orthicker
[] Wood preservative
[] Caulk [] #10 x l" wood screws (7)
[] Drilland %2" orsmallerbit
(umber
Parts Supplied (on some models)
Check that allparts are included in parts package.
IMPORTANT: Observe all governing codes and ordinances.
Check the location where air conditioner will be installed. Proper
installation is your responsibility, Make sure you have everything
necessary for correct installation.
The location should provide:
[] Grounded electrical outlet within 4 ft (I 22 cm) of where the
power cord exits the air conditioner.
NOTE: Do not use an extension cord.
[] Free movement of air in room to be cooled.
[] A large enough opening for the air conditioner,
[] Adequate wallsupportforweighto(airconditioner. Air
conditioner weighs between 70 and 851bs (32 to 40 kg),
NOTE: Cabinet louvers must not be obstructed. Air must be able
to pass freely through the cabinet louvers.
C
E F
(
D
A. Foam window sash seal
B. Window lock bracket
C. Side curtains (2)
D. Foam seal
NOTE: Installation parts are supplied for double-hung windows
up to 36" (91.4 cm) wide. A special Wide Window Kitis available
from your dealer or serv(ce center. See "Accessories."
NOTE: DO NOT USE ANY SCREWS OTHER THAN
THOSE SPECIFIED HERE
E. #10x 1//pan-head Phillipsscrews (3)
F. #10x _" round-head screws (6)
G. Top channel
H. #10x ¼" pan-head Phillips screws (3)
H
G
A. Cabinet louvers
P/N 2020213A0155 1
Window Installation
Window opening measurements:
[] 27" to 36" (68.6 cm to 91.4 cm) opening width.
[] 17"(43.1cm) minimum opening height.
mA__t_
B
{
[:7_ =_
1 I
A. 27"(68.6cm) minimum
B. 17" (43.1cm) minimum
Through=the=Wall Installation
,r
The wall opening measurements should be:
[] Width: 22s/8"(57.5 cm) plus twice thickness of wood used to
build frame.
[] Height: 16" (40.6 cm) plus twice thickness of wood used to
bui{d frame.
[] Depth: 2_/2" (6.4 cm) minimum to 6V2" (16.5cm) maximum.
? ....................... _ii_ii........ C
t
C
A. 16"(40.6 cm)
B. 225/_" (57,5 cm)
C. Wood thickness
D. 21/2"(6.4) minimum to
61/2"(16.5cm) maximum.
2
iNSTALLATiON iNSTRUCTiONS
Excessive Weight Hazard
Use two or more people to move and install
air conditioner,
Failure to do so can result in back or other injury.
Remove packaging materials
[] Remove and dispose of/recycle packaging materials,
Remove tape and glue residue from surfaces before turning
on the air conditioner, Rub a small amount of liquid dish soap
over the adhesive with your fingers, Wipe with warm water
and dry.
[] Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your air conditioner.
[] Handle the air conditioner gently.
1. Remove the air conditionerfrom the carton and place iton
cardboard,
4. Pull on the handles to slide the air conditioner out of the
cabinet. Place the air conditioner on cardboard.
A
A, Handle
NOTE: Do not lilt, push, pull or remove any expanded
polystyrene (foam)from inside the air conditioner. It is not
packing material.
2. Remove 1 shipping screw from each side of the cabinet.
A
A.Shipping screw
3. Remove front panel by removing 1 phillips screw from each
side of the front panel, Set screws aside and save.
°°°°6 A
A
A.front panel screw
Loading...