Frigidaire FAS256R2A1, FAM186R2A2, FAS296R2A1, FAS256R2A2, FAM156R1A1 Use & Care Manual

Contents

2 Warranty
3 Product Registration
3 Packaging
3 Normal Sounds
4 Important Safety Instructions
4 Operation of Current Device
5-10 Air Conditioner Features

11 Care and Cleaning
11 Energy Saving Ideas
12 Avoid Service Checklist

NOTE: This USE & CARE MANUAL
provides specific operating instructions
for your model Use the room air
conditioner only as instructed in this USE

& CARE MANUAL instructions are not
meant to cover every possible condition

and situation that may occur. Common
sense and caution must be practiced when
instalIing, operating, and maintaining any
appliance.

READ AND SAVE THESE INSTRUCTIONS

ELEC ONiC

P/N 66121617

ROOM AIR CONDITIONER WARRANTY

Yourproduot /s proteoted by this warranty

Your appliance is warranted by Electrolux. Electrolux has authorized Frigidaire Consumer Services and their authorized servicers to perform service under this
warranty. Electrolux authorizes no one else to change or add to any of these obligations under this warranty. Any obligations for service and parts under this
warranty must be performed by Frigidaire Consumer Services or an authorized Frigidaire servicer.

WARRANTY FRIGIDAIRE, THROUGH ITS AUTHORIZED THE CONSUMER WILL BE

PERIOD SERVICERS, WILL: RESPONSIBLE FOR:

FULLONE-YEAR One year from Pay all costs for repairing or replacing parts of Costs of service calls that are listed under

WARRANTY original purchase this appliance which prove to be defective in NOR_ MAL RESPONSIBILITIES OF THE

date. materials or workmanship. CONSUMER.*

LIMITED2-5 Becond through fifth Repair or replace any parts in the Sealed Diagnostic costs and any removal
YEAR ears from original Refrigeration System (compressor, condenser, transportation and reinstallation costs
WARRANTY _urchasedate. evaporator end tubing/ proves to be defective in which are required because of service.

materiels or workmanship. Costs for labor, parts and transportation

(Sealed System) other than with respect to the Sealed

Refrigeration System.

* NORMAL

RESPONSJBlUTJES OF

THE CONSUMER

This warranty applies only to products in ordinary household use, and the consumer is responsible for the items

listed below.

1. Proper use of the appliance in accordance with instructions provided with the product.

2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance
with all local plumbing, electrical and/or gas codes.

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections
or defects in house wiring.

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc. which are
not a part of the appliance when it was shipped from the factory.

5. Damages to finish after installation.

6. Damage to unit after removal from packaging carton.

EXCLUSIONS

IF YOU NEED SERVICE

This warranty does not cover the following:

1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY. Note: Some states do not allow

the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.

2. Sewice calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary
household use. The consumer shall pay for such sewice calls.

3. Damages caused by services performed by persons other than authorized Frigidaire servicers; use of parts other than

Frigidaire Genuine Renewal Parts; obtained from persons other than such servicers; or external causes such as abuse,

misuse, inadequate power supply or acts of God.

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty
period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This written
warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this
warranty must be obtained by following these steps, in order:

1. Contact Frigidaire Consumer Services or an authorized Frigidaire seRticer.

2. If there is a question as to where to obtain service, contact our Consumer Relations Department at:

Frigidaire
P.O. Box 212378

Augusta, GA 30917

800°444°4944

CANADA

Electrolux Canada Group

6150 McLaughlin Road
Mississauga, Ontario L5R 4C2

1°866°213-9397

Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by

Electrolux.
This warranty applies only in the 50 states of the U.S.A. Puerto Rico and Canada.

FOR SERVICE CALL 1o800o444o4944.

Product Registration

Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers. On all models, the serial

plate is located on the outside of the cabinet.

Model No.

Serial No.

Register Your Product

The self-addressed PRODUCT REGISTRATION CARD should be filled in completely, signed
and returned to the Frigidaire Company.

Packaging

Remove aH packaging from inside the unit ,amso any inserts placed into

the side _ouvers.

Packing inserts

Norma Sounds

Sound of Rush/?Tg A/?

At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.

i-//qh P/Zched Chatter

Today's high efficiency compressors
may have a high pitched chatter
during the cooling cycle.

Vibr_Ttio,q

Unit may vibrate and make noise
because of poor wall or window
construction or incorrect installation.

P/hC//hg or Sw/sh/hc/

Droplets of water hitting condenser
during normal operation may cause
'pinging or swishing" sounds.

G_rd/e/,_i/L_ s J

'Gurgling or hissing' noise may be heard
due to refrigerant passing through
evaporator during normal operation.

important Safety
instructions

The power supply cord with
this air conditioner contains a current
detection device designed to reduce the risk

of fire.

Please refer to the section 'Operation of

Current Device' for details.

In the event that the power supply cord is
damaged, it cannot be repaired it must be
replaced with a cord from the Product

Manufacturer.

Avoid fire hazard or electric
shock. Do not use an extension cord or an
adaptor plug. Do not remove any prong from
the power cord.

Grounding type walm
receptacle

JJ_ circumstances, cut,

[ remove, or bypass the

, grounding prong.

P

Power supply cord

with 3-prong grounding

pmugand current
detection device

Read aiminstructions before using this air conditioner.

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance= Read product labels for flammability and other warnings=

Prevent Accidents

Toreduce the risk of fire, electrical shock, or injury to persons when using your air conditioner,
follow basic precautions, including the following:

Be sure the electrical service is adequate for the mode! you have chosen. This information

can be found on the serial plate, which is located on the side of the cabinet and behind the
grille.

If the air conditioner is to be installed in a window, you will probably want to clean both
sides of the gIass first= If the window is a triple-track type with a screen paneJ included,
remove the screen compIetety before installation.

Be sure the air conditioner has been securely and correctly installed according to the
separate instaIIation instructions provided with this manual= Save this manual and the

JnstalIatJon instructions for possible future use in removing or reinstalling this unit=
When handIing the air conditioner, be careful to avoid cuts from sharp metat fins on front
and rear coils.

Electrical Information

The complete electrical rating of your new room air conditioner is stated on the seriaI plate=

Refer to the rating when checking the electrical requirements=

Be sure the air conditioner is properly grounded= To minimize shock and fire hazards,
proper grounding is important= The power cord is equipped with a three-prong grounding
plug for protection against shock hazards=
"Your air conditioner must be used in a properly grounded wall receptacle= If the wall
receptacle you intend to use is not adequately grounded or protected by a time delay fuse
or circuit breaker, have a quaIified electrician instalI the proper receptacle=

Do not run air conditioner with outside protective cover in place= This could result in

mechanical damage within the air conditioner.

Do not use an extension cord or an adapter plug,

READ THiS SECTION BEFORE ATTEMPTING TO OPERATE AiR CONDiTiONER.

Operation of Current

Device

Plug in &
press RESET

NOTE: Some plugs have

buttons on the top.

The power supply cord contains a current device that senses damage to the power cord. To
test your power supply cord do the following:

1. Plug in the Air Conditioner.

2. The power supply cord will have TWO buttons on the ptug head. Press the TEST button.
You will notice a click as the RESET button pops out.

3. Press the RESET button. Again you will notice a click as the button engages.

4. The power supply cord is now supplying electricity to the unit. (On some products this is
also indicated by a light on the plug head).

NOTES:

Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is

pushed, or it cannot be reset=A new one can be obtained from the product manufacturer=

If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one
obtained from the product manufacturer.

Air Conditioner Features ELECTRONICCONTROLOPERATmNG NSTRUCT ONS

LIGHT

ON!OFF _ /

ADJUSTS
TEMP &
TIME

SETS
MODE

Fig. "A"

REMOTE CONTROL
FOR HEAT MODELS

ON/OFF

SETS

_FAN

SPEED

ADJUSTS
TEMP & 4:
TIME

SETS
MODE

Fig. "B"

s_, Only

R_m0t_
S_,,_J,,,,

REMOTE CONTROL

w/DISPLAY &

REMOTE SENSING

BUTTON

-- ACTIVATE
TIMER

AUTO TEMP

/

Before you begin, thoroughly familiarize yourself with the controi pane! and remote as shown

below and all its functions, then follow the symbol for the functions you desire= The unit can

be controlled by the touch pad alone or with the remote.

ADJUSTS DmSPLAYS

AUTO TEMP

TEMP & TEMPERATUREiTmME

FEATURE TmME FAN SPEED SLEEP MODE

CLEAN AIR

(some msdsls)

CHECK FILTER

RESET BUTTON

SETS FAN SPEED

LIGHT

SETS

ACTIVATES
TIMER

TOUCH PAD

TURNS UNIT
ON OR OFF

SETS

FAN
SPEED

h

ACTIVATE

TEMER

AUTO TEMP

ON!OFF

ADJUSTS
TEMP &
TIME

SETS
MODE

oo n_ °%

STANDARD REMOTE

SETS

FAN

SPEED

._ACTIVATE

"---_TIM ER

AUTO TEMP

Battery Size: AAA

Warning: do not mix old and new batteries= Do not mix alkaline, standard (carbon=zinc),or rechargeable(nickeFcadmium) batteries=

NOTE: The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.

TO TURN UNIT ON: YOU WILL SEE:

DO THIS:

PRESS ON/OFF

BUTTON

Cool

EnergySayer

Air Conditioner Features

(continued)

TO CHANGE TEMPERATURE

SETTING: YOU WILL SEE:

Remote

Sensing

DO THIS:

PRESS TO

RAISE

PRESS TO

LOWER

Note: Tap or hold either up (A) or down (V) button until the desired temperature is seen on the display. This temperature will be automati-
cally maintained anywhere between 60°F (16°C) and 90°F (32°C) for cooling mode. The temperature will be automatically maintained anywh-
ere between 55°F (13°C) and 80°F (27°C) for heating mode. If you want the display to read the actual room temperature. See "To Operate
on Fan Only" section on Page 7.

TO ADJUST FAN SPEEDS:

Cood

DO THIS:

PRESS

TO SELECT

FASTER

SLOWER

YOU WILL SEE :

Press the Fan Faster button will increase the fan speed from Low (LO), to Medium (ME), to High (HI). The digital display will indicate
your chosen speed. Press the Fan Slower button will decrease the fan speed from High (HI), to Medium (ME), to Low (LO).The digital display will
indicate your chosen speed.After 5 seconds the display will revert back to the set temperature.

TO USE AUTO TEMP FEATURE:

LIGHT On

DO THIS:

PRESS

AUTO TEMP

YOU WILL SEE:

Note: Fan speed starts at High Speed and adjusts to a slower speed as the room temperature dictates, For example if the room doesn't
get too warm, it will stay at the slowest speed. If the room temperature rises quickly, such as a door being opened, it will automatically go
to the highest speed. The fan speeds will re-adjust back to the slowest speed as the room returns to the original set temperature.

Air Conditioner Features

(continued)

TO OPERATE ON FAN ONLY: YOU WILL SEE:

LIGHT On

PRESS _°J! '

MODEBUTTONFANCHOOSEoNLY E'_rgz _'__ OHe_

Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air. (Remember to open the

vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. (Exc-

ept "Auto Temp").
During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode.
Fan Only cannot be selected when the unit is in the 'Remote Sensing' Mode. (On those units with that feature).

TO USE THE

ENERGY SAVER FEATURE:

LIGHT On

DO THIS:

PRESS

MODE BUTTON

CHOOSE

ENERGY SAVER

YOU WILL SEE:

Note: In this mode, the fan will continue to run for another 3 minutes after the compressor shuts off. The fan then cycles on for 2 minutes

at 10 minute intervals until the room temperature is above the set temperature, at which time the the cooling system turns back on.

TIMER: DELAY START/STOP FEATURE: LIGHT On YOU WILL SEE HOW MUCH TIME IS CHOSEN:

FIRST

DO THIS:

PRESS

TIMER BUTTON

THEN

DO THIS:

PRESS
TEMP_IMER
SET BUTTON

Note 1: For Delay Stop, the unit must be in the On position.
Note 2: For Delay Start, the unit must be in the Off position.
First, PRESS TIME BUTTON

Then to adjust timer setting, tap or hold the UP arrow ( • ) or the DOWN arrow ( • ) to change delay timer at. 5 hour increments, up to 10

hours, then by 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7.5, 7, etc.). The Delay Start
mode automatically selects cooling with maximum Fan Speed. The temperature maintained will be the same as previously set. To change the

set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5 seconds, the con-
trol will automatically change the display back to the hours remaining until the unit will start/stop. PRESSING the unit On/Off button at any
time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either starts or stops. Once that happens

he above steps have to be repeated again.

7

Air Conditioner Features

(continued)

CHECK FILTER FEATURE:

YOU WILL SEE:

LIGHT On

Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation and cooling. The LED (light) will

illuminate after 250 hours of operation. To reset after cleaning the filter, press the "Check Filter" button and the light will go off.

CLEAN AIR FEATURE(onsomemodels):

CooJ(

Fan Onty(

i

i

!

LIGHT On

DO THIS:

PRESS

CLEAN AIR

BUTTON

YOU WILL SEE:

Note: When this feature is "ON", the electronic air purifier is energized to remove pollen and impurities from the air. To cancel this feature,
press the Clean Air button (the LIGHT will turn off).
Note: This feature can be activated on the unit touchpad ONLY.

SLEEP FEATURE: YOU WILL SEE:

LIGHT On

DO THIS:

PRESS

SLEEP BUTTON

Energy Saver

Fan Only

Note: In this "MODE" the set temperature will increase by 2 degrees F 30 minutes after the mode is selected. The temperature will then
increase by another 2 degrees F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the or-
iginally selected temperature. This ends the "Sleep" MODE and the unit will continue to operate as originally programmed. The "Sleep"
MODE program can be cancelled at any time during operation by again pressing the "Sleep" button.

Air Conditioner Features

(continued)

REMOTE SENSING FEATURE

(on some models) •

DO THIS:

PRESS REMOTE

SENSING

BUTTON ON

LIGHT pulsing On & intermittently.

NOTE:Unit display shows"set"temperature

NOTE: Remote display

is actual temperature at

remote control only

Note: This feature can be activated from the remote control ONLY,the unit must be in a cooling mode.

To activate the remote sensing feature,point the remote control towards the unit and press the remote sensing buttonNext,use the
buttons to set the desired temperature at the remote.(Note that the set temperature will only be displayed on the unit itsetf).The LIGHT on
the unit control wilt pulse to indicate it received the signal.The LIGHT on the remote control will pulse each time it sends a signal.It will con-
tinue to send this signal until the feature is deactivated by pressing the remote sensing button.If the unit does not receive the remote sensing

signal during any 3 minute interval,the unit will beep to indicate the remote sensing mode has ended.The display on the remote control indicates
the temperature at the remote ONLY. The unit display indicates the set temperature.

Remote Sensing:The Remote Sensing function is terminated using the remote control StartJStop button or the Remote Sensing
Stop button, and also the main Start/Stop button on the unit.

HEATING FEATURE (on some modes)

DO THIS:

PRESS

MODE BUTTON

SELECT HEAT

YOU WILL SEE:

Note: This feature can be used with any combination of FAN Speeds, Timer, or Sleep Modes.When in the "Heat" Mode,the fan wilt run

continuously while heat is needed. The temperature wilt automatically be maintained anywhere between 55 ° F(13C)and 80 ° F(27C)
When the room set temperature is satisfied,the fan will cycle off and on to circulate and sample the room air.

TO TURN UNIT OFF:

DO THIS:

ON/OFF BUTTON

YOU WILL SEE:

Note: When unit is shut off in the Heat Mode, the fan will continue to run for a few seconds to dissipate
residual heat within the unit.

9

÷

Air Conditioner Features

(continued)

FAULT CODES

If the display reads"HS", a sensor has failed. If the display reads"AS", a sensor has failed, the display reads"ES", a sensor has failed.

Contact your Authorized Frigidaire Service Contact your Authorized Frigidaire Service Contact your Authorized Frigidaire Service
Center. Center. Center.

÷

ADDiTiONAL THINGS YOU SHOULD KNOW

Now that you have mastered the operating procedure,here are more features in your control that you should become familiar with:

The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned offand on
quickly.This prevents overheating of the compressor and possible circuit breaker tripping.The
fan will continue to run during this times.

• The control will maintain the set temperature within 2 degrees Fahrenheit,between 60F and 90F degrees.

" The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius.To convert from one to the other and back,

Press and hold the"TEMP/TIMER"Up ( • ) and Down ( • ) buttons together for 3 seconds.

Fresh Air Vent Control(On some models)

The Fresh Air Vent allows the air conditioner to:

1. Recirculate inside air - Vent Closed (see Fig. 1 )

2. Draw fresh air into the room - Vent Open (see Fig. 2)

3. Exchange air from the room and draws fresh air into the room - Vent and Exhaust
Open (see Fig. 3)

÷

Fig. 1 (OFF)

Fig. 2 (FRESH AIR)

Fig. 3 (VENT)

(4=WAY)

AUGER WHEEL

The louvers will allow you to direct the air flow Up or Down and Left or Right throughout

the room as needed.Rotate the Auger Wheel Up or Down until the desired direction is

obtained.

10

÷

Care and C eaning

Clean your air conditioner occasionally to keep it Iooking new. Be sure to unplug the
unit before emeaning to prevent shock or fire hazards.

Air Filter Cleaning

The air fiIter shouid be checked at least once a month to see if cleaning is necessary.
Trapped particles in the fiiter can build up and cause an accumulation of frost on the

cooling coils.

Push the vent handle to the Vent Closed position (where applicable).
, Open the front panei.
, Grasp the filter by the center and pull up and out.
, Wash the filter using Iiquid dishwashing detergent and warm water. Rinse filter

thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly dry

before replacing.
, Or, instead of wasNng you may vacuum the filter clean.

Cabinet Cleaning

Be sure to unpIug the air conditioner to prevent shock or fire hazard. The cabinet and

front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution

of warm water and miId Iiquid dishwashing detergent. Rinse thoroughly and wipe dry.

Never use harsh cleaners, wax or polish on the cabinet front.

Be sure to wring excess water from the cloth before wiping around the controls. Excess

water in or around the controls may cause damage to the air conditioner.

Plug in air conditioner.

Winter Storage

If you plan to store the air conditioner during the winter, remove it carefully from the

window according to the installation instructions. Cover it with plastic or return it to the
original carton.

Energy Saving Ideas

Do not block air flow inside with btinds, curtains or furniture; or outside with shrubs,

enclosures, or other buiJdinge.

The capacity of the room air conditioner must fit the room size for efficient and satisfactory

operation,

InstalI the room air conditioner on the shady side of your home. A window that faces north
is best because it is shaded most of the day.
Close the fireplace damper, floor and wail registers so cool air does not escape up the

chimney and into the duct work.

Keep biinds and drapes in other windows closed during the sunniest part of the day.
Clean the air filter as recommended in the section "Care and CIeaning/'
Proper insulation and weather stripping in your home will help keep warm air out and cool

air in.
External house shading with trees, plants or awnings will help reduce the air conditioner's

work load.

Operate heat producing appliances such as ranges, washers, dryers and dishwashers

during the coolest part of the day.

11

÷

Avoid Service Checklist

Before calIing for service, review this list, Htmay save you time and expense, This list
includes common occurrences that are not the result of defective workman-ship or
materials in this appliance,

÷

OCCURRENCE SOLUTION

Air conditioner will not operate.

Air from unit does not feemcored
enough.

Air conditioner cooling, but room is
too warm - ice forming on cooming

coil behind decorative front.

Air conditioner cooling, but room is
too warm - NO ice forming on
cooling coil behind decorative front.

Air conditioner turns on and off
rapidmy.

Noise when unit is cooling.

Wall plug disconnected. Push plug firmly into wall outlet.

Plug Current Device Tripped. Press the RESET button.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Control is OFR Turn Control ON and set to desired setting.

Room temperature below 60F (16':C). Cooling may not occur until room temperature rises above 60:'F (16'C).

Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.

Reset to a Lower temperature.

Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to restart
when set in the COOL mode.

Outdoor temperature below 60'F (18':C). To defrost the coil, set FAN ONLY Mode.
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY Mode.
Temperature is set too Low for night-time cooling. To defrost the coil, set to FAN ONLY Mode. Then, set Tem-

perature to a Higher setting.

Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.
Temperature is set too High. Set temperature to a Lower setting.
Air directional louvers positioned improperly= Position louvers for better air distribution.

Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in front of unit.

Doors, windows, registers, etc= open - cold air escapes. Close doors, windows, registers, etc=

Unit recently turned on in hot room. Allow additional time to remove 'stored heat' from walls, ceiling, floor and
furniture.

Dirty air filter - air restricted. Clean air filter.
Outside temperature extremely hot. Set FAN speed to a faster setting to bring air past cooling coils more

frequently.

Air movement sound. This is normal. Fftoo loud, set to a slower FAN setting.
Window vibration - poor installation. Refer to installation instructions or check with installer.

Water dripping iNSiDE when unit is Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to installation
cooling, instructions - check with installer.

Water dripping OUTSIDE when unit Unit removing large quantity of moisture from humid room. This is normal during excessively humid days.
is cooming,

Remote Sensing Deactivating Remote control not located within range. Place remote control within 20 feet & 180':, radius of the front of the
Prematurely (Some fv'lodems}, unit.

Room Too Cold.

Remote control signal obstructed. Remove obstruction.

Set temperature too low. Increase set temperature.
Remote Sensing activated (on some models) and remote control located in Hot Spot - Relocate remote

control or deactivate remote sensing.

÷

if These Solutions Fai , 1-800-444-4944 For Frigidaire Service.

12

÷