Frigidaire FAK103N1V, FAK083N7V Owner’s Manual

_R'SGUi

READ AND SAVE THESE INSTRUCTIONS

N ITIONIEIR

ROTARYCONTROL

P/N 309000854 (0603)

ROOM AIR CONDITIONER WARRANTY

Your product is protected by this warranty

Your appliance is warranted by White Consolidated Industries, Inc. WCI has authorized Frigidaire Consumer Services and their authorized servicers to perform
service under this warranty, WCI authorizes no one else to change or add to any of these obligations under this warranty. Any obFigations for service and parts
under this warranty must be performed by Frigidaire Consumer Services or an authorized Frigidaire servicer,

FULL ONEoYEAR
WARRANTY

UMITED 2ND-STH
YEAR WARRANTY

(Sealed System)

LIMITED
WARRANTY

(Applicable to the
State of Alaska)

*NORMAL
RESPONSIRILmES
OF THE CONSUMER

EXCLUSIONS

IF YOU NEED SERVICE

WARRANTY

PERIOD

One year from original
purchase date

Secondthrough fifth years
from original purchase

date

Time periods listed above

This warranty applies only to products in ordinary household use, and the consumer is responsible for the
items listed below.

I. Proper use of the appliance in accordance with instructions provided with the product.

2. Proper insta%Ron by an authorized servicer in accordance with instructions provided with the appliance and in accordance
with all local plumbing, electrical and/or gas codes,

3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections
or defects in house wiring.

4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc, which are not a
part of the appliance when it was shipped from the factory.

5. Damages to finish after installation,

6. Replacement of light bulbs and/or fluorescent tubes (on models with these features),

This warranty does not cover the following:

I. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTYDAMAGE AND INCIDENTAL EXPENSESRESUL]ING FROM

ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY,
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or

exclusion may not apply to you

2. Service calls which do not involve malfunction or defects in workmanship or material, or for app%nces not in ordinary
household use. The consumer shall pay for such service calls.

3. Damaqes caused by services perlormed by persons other than authorized Frigidaire servicers; use ol parts other than Frigidaire
Genuir_e Renewal Parts; obtained from persons other than such servicers; or external causes such as abuse, misuse, inadequate

power supply or acts of God,

4. Products with original serial numbers that have been removed or altered and cannot be readily determined.

gives you specific legal rights. You may also have other rights that vary from state to state, Service under this warranty must be
obtained by following these steps, in order:

I. Contact Frigidaire Consumer Services or an authorized Frigidaire servicer.

2. If there is a question as to where to obtain service, contact our Consumer Relations Department at:

FRIGIDAIRE, THROUGH ITS AUTHORIZED

SERVICERS, WILL:

Pay all costs for repairing or replacing parts of this
appliance which prove to be defective in materials or
workmansNp

Repair or replace any parts in tile Sealed Reffige/ation
Systern (compressor, condenser, evaporator and tubing)
proves to be defective in rnaterials or workmanship

All of the provisions of the full and limited warranties above
and the exclusions listed below apply

Costs of service calls that are listed under NOR-
MAL RESPONSIBILITIESOF THE CONSUMER.*

Diagnostic costs and any removal, transportation
and reinstallation costs which are required because
of service Costsfor labor, partsand transportation
other than with respect to the SealedRefrigeration
System

Costs of the technician's travel to the home and
any costs for pick up and delivery of the appliance

required becauseof service

THE CONSUIVlER WILL BE

RESPONSIBLE FOR:

Frigidaire Company
RO. Box 212378

Augusta, GA 30917

Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by White
Consolidated Industries, inc. This warranty applies only in the 50 states of the U,S A., Puerto Rico and Canada.

C O M PA _ Y

Product Registration

Record Your Mode[ and Serial Numbers

Record in the space provided below the model and serial numbers. On most
models, the serial plate is located on the outside of the cabinet. On some models,
remove the filter and look at the bottom edge of the air conditioner behind tile
front grille for the model and serial numbers. Reading these numbers may be easier
by using a flashlight or by removing the cabinet front as instructed under "Care
and Cleaning."

Mode[ No.

Serial No.

Register Your Product

Tile self-addressed PRODUCT REGISTRATIONCARD should be filled in completely,
signed and returned to the Frigidaire Company.

Contents

NOTE: This Owner's Guide provides
specific operating instructions for your
model. Usethe room air conditioner only

as instructed in this Owner's Guide.

These instructions are not meant to

(:over every possible condition and
situation that may occur. Common sense
and caution must be practiced when
installing, operating, and maintaining
any appliance.

Normal Sounds

.?oz_t_ff_/"l¢_sbitz2 4i_"
At the front of tile unit,

you may hear the sound
of rushing air being moved
by the fan.

2
3
3

4
4

S
5-6

7
8

Today's high efficient
compressors may have a
high pitched chatter during
the cooling cycle.

Warranty
Product Registration

Normal Sounds
Important Safety Instructions

Energy Saving Ideas
Using Air Conditioner

Air Conditioner Features
Care and Cleaning

Avoid Service Checklist

_7&t'dt£)_7

Unit may vibrate and make
noise because of poor wall

or window construction or
in(orrect installation.

7_,wostm _C!£:bi_

As cooling systems cycle on
and off, you may hear a

"dicking" sound.

© 1996 White Consolidated Industries, Inc,

All rights reserved.

iJill_d O___'mi@i_7_
Droplets of water hitting

-- condenser during normal
operation may (ause

"pinging or swishing"

sounds.

"Gurgling or hissing"
noise may be heard due to refrigerant
passing through evaporation during normal
operation.

3

mmportant Safety
mnstructions

Avoid fire hazard or

electric shock. Do not use an extension
cord or an adaptor plug. Do not remove

any prong from the power cord.

Grounding type
wail receptacle

Do not, under -_
any circumstances, /

cut, remove, |
or bypass the )

_grounding prong,_

Power supply
cord with 3-prong
grounding pJug

Read a[[ instructions before using this air conditioner.

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance. Read product labels for flammability and other warnings.

Prevent Accidents

To reduce the risk of fire, electrical shock, or injury to persons when using your air
conditioner, follow bask precautions, including the following:

Be sure the electrical service is adequate for the model you have chosen. This
information (an be found on the serial plate, which is located either on the side
of the cabinet or behind the grille.
If the air conditioner is to be installed in a window, you will probably want to
clean both sides of the glass first. If the window is a triple4rack type with a
screen panel included, remove the screen completely before installation.
Be sure the air conditioner has been securely and correctly installed according to
the separate installation instructions provided with this manual. Savethis manual
and the installation instructions for possible future use in removing or reinstalling

this unit.
When handling the air conditioner, be careful to avoid cuts from sharp metal fins

on front and rear coils.

Electrical Information

The complete electrical rating of your new room air conditioner is stated on the
serial plate. Refer to the rating when checking the electrical requirements.

Be sure the air conditioner is properly grounded. To minimize shock and fire
hazards, proper grounding is important. The power cord is equipped with a
three-prong grounding plug for protection against shock hazards.
Your air conditioner must be used in a properly grounded wall receptacle. If tile
wall receptacle you intend to use is not adequately grounded or protected by a
time delay fuse or circuit breaker, have a qualified electrician install the proper
receptacle.
Do not run air conditioner with outside protective cover in place. This could result
in mechanical damage within the air conditioner.

• Do not use an extension cord or an adapter ptug.

Energy Saving Ideas

Do not block air flow inside with blinds, curtains or furniture; or
outside with shrubs, enclosures, or other buildings.

The capacity of the room air conditioner must fit the room sizefor efficient and
satisfactory operation.
Install the room air conditioner on the shady side of your home. A window that
faces north is best because it isshaded most of the day.
Close the fireplace damper, floor and wall registers so cool air does not escape
up tile chimney and into tile duct work.
Keep blinds and drapes in other windows closed during tile sunniest part of the
day.
Clean tile air filter as recommended in the section "Care and Cleaning."
Proper insulation and water stripping in your home will help keep warm air out

and cool air in.
External house shading with trees, plants or awnings will help reduce the air

conditioner's work load.
Operate heat producing appliances such as ranges, washers, dryers and

dishwashers during the coolest part of the day.

Toreducetheriskoffire,electricshock,orinjuryto persons,read

w_i,_,_,n_Air Conditioner the IMPORTANT SAFETYINSTRUCTIONSbefore operating this appliance.

To begin operating the air conditioner, follow these steps:

NOTE: If the air conditioner isturned off,

wait 3 minutes before restarting. This

allows pressure inside the compressor to
equalize. Failure to follow these
instructions may cause inefficient
operation.

1. Plug in the air (onditioner. (Toprevent electrical hazards, do not use an extension
cord or an adapter plug.)

2. Set the thermostat to the highest number (coldest or cooler setting).

3. Set the selector (ontrol to the highest COOL setting (see below).

4. Adjust the louvers for (omfortable air flow (seeAir Dire(tional Louvers).

5. Once the room has cooled, adjust the thermostat to the setting you find most
comfortable.

Review the "Air Conditioner Features" section for other settings.

Air Conditioner Features

The contro/s featured in this manual are representational of the many models
avai/ab/e. Your model may offer slight!y different features.

COOL Mode

When in one of the COOL settings, the air conditioner runs all the time, circulating
the air. Cooling starts only if the room temperature rises above the coolness level
selected on the TEMP Control, and stops once the set coolness level isreached. This
setting gives the most even room temperatures.

FAN Mode

When in the FANsetting, the fan Funs continuously to circulate air in the room
without cooling.

Automatic Thermostat

When a COOL setting isselected, the thermostat controls the amount of cooling by
automatically turning the cooling compressor on and off in response to the room
ternperatu re.

Set the thermostat at the highest number for the coldest setting for cooling. Once
the room has reached the desired temperature, adjust the thermostat to a number
providing the most comfortable amount of cooling. Higher numbers provide lower
room temperatures. Lower numbers provide warmer room temperatures.

Night Time Cooling

When outside temperatures drop below 70% (21°C) and the unit is cooling, frost
may form on the coils and block airflow into the room. If this occurs, operate the
air conditioner on the FAN setting (or CONSTANT FAN/HIGH on Energy Saver
models) to defrost the coil.

If cooling while the outside temperature is low, set the thermostat to the middle
position. Make sure the louvers are open. This will help prevent frost build-up.

Air Conditioner Features

(continued)

Rotary Vent Control

This Vent Control allows the air conditioner to either recirculate inside air (CLOSED)
or exhaust air to the outside (OPEN). These selections can be used with any FAN

selection.
The CLOSEDposition is used when maximum cooling is desired. It may also be used

for air recirculation without cooling when the air conditioner is set in any FAN
position.

The OPENposition removes stale air from the room and exhausts it to the outside.
Fresh air is drawn in through normal passages in the home.

(4-WA/)

4oWay Louvers

The 4-Way air directional louvers allow you to direct air flow up or down, left or
right throughout the room as needed. To adjust the air directional louvers side4o_
side, use the center handle asyou move it side4o-side.

Care and Cleaning

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug
the unit before cleaning to prevent shock or fire hazards.

Air Filter Cleaning

The air filter should be checked at least once a month to see if cleaning is necessary.
Trapped particles in the filter can build up and cause an accumulation of frost on
the cooling (oils.

Grasp the filter by the (enter and pull up and out.
Wash the filter using liquid dishwashing detergent and warm water. Rinse filter
thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly
dry before replacing.
Or, instead of washing you may vacuum the filter clean.

Cabinet Cleaning

Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and

front may be dusted with an oil-free cloth or washed with a cloth dampened in a
solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and

wipe dry.

Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping around the controls.

Excesswater in or around the controls may cause damage to the air conditioner.

The cabinet front can be removed for more thorough cleaning. To remove the front
for cleaning first remove the front retaining screw as shown in the picture. To remove

the front press firmly on each side of the cabinet close to the front, approximately

halfway down, and gently pull the front out and lift up to release from the cabinet.
Clean the front in a sink using liquid dishwashing detergent and warm water. Rinse

thoroughly and dry.

Replace cabinet front. Replace the screws.
Plug in air conditioner.

Winter Storage

If you plan to store the air conditioner during the winter, remove it carefully from the
window according to the installation instructions. Cover it with plastic or return it to the

original carton.
NOTE: To prevent rust or e[ectrka[ connections from being damaged, store air

conditioner in an upright position and a dry place. A winter cover can be
purchased from your dealer. The cover will protect the air conditioner when it is left in

place through the winter.

Avoid Service ChecMBt BeforecaU ngforservice,reviewth sl st. may aveyoutu .eandexpense.This

list includes common occurrences that are not the result of defective workman-

ship or materials in this appliance.
OCCURRENCE SOLUTION
Air conditioner will not operate. Wall plug disconnected_ Push plug firmly into wall outlet

House fuse blown or circuit breaker tripped Replace fuse with time delay type or reset circuit
breakec

Selector Control in OFFposition Turn selector to ON (some models) or the desired FAN or COOL
setting_

Unit turned off by moving thermostat to a higher number and then immediately turning back to
a colder number Wait approximately 3 minutes_ Listen for compressor to start

Unit turned off and then on too quickly Turn unit off and wait 3 minutes before restarting_
Thermostat set too low Adjust thermostat to higher number for cooling

Air from unit does not feel cold

enough.

Turn selector to a higher FAN or COOL position
Thermostat set too warm_ Set thermostat to colder temperature
Room temperature below 70°F (21°C) Cooling may not occur until room temperature rises above

70°F (21°C)_

Temperature sensing tube touching cold coil, located behind air filter Straighten tube away from coil,

Air conditioner cooling, but room is
too warm -- ice forming on cooling

Outdoor temperature below 70°F (21°C)_ To defrost the coil, set selector to FAN position Then,
set therrnostat to warmer position_

coil behind decorative front,

Air filter rnay be dirty Clean filter, Refer to Care and Cleaning section_ To defrost, set selector to
FAN

Thermostat set too cold for night-time cooJing_ To defrost the coil, set selector to a FAN position,
Then, set thermostat to a warmer position

Air conditioner cooling, but room is Dirty air filter -- air restricted Clean air fiJtec Refer to Care and Cleaning section
too warm -- NO ice forming on

cooling coil behind decorative front. Thermostat set too warm. Turn thermostat clockwise to a colder setting.

Thermostat set on low numbec Turn thermostat to higher number
'Centset at OPEN position Set vent at CLOSEDposition for maximum cooling
Air directional Iouvres positioned improperly Position Iouvres for better air distribution_
Front of unit isblocked by drapes, blinds, furniture, etc -- restricts air distribution. Clear blockage

in front of unit,

Doors, windows, registers, etc_open -- cold air escapes Close doors, windows, registers, etc
Unit recently turned on in hot roorn Allow additional time to rernove "stored heat" from walls,

ceiling, floor and furniture

Air conditioner turns on and off

Dirty air filter -- air restricted Clean air filter,

rapidly.

Outside temperature extremely hot. Set FAN on high speed to bring air past cooling coils more
frequently,

Noise when unit is cooling, Air movement sound_ This is normal If too loud, turn selector to lower FAN setting

Sound of fan hitting water-moisture removal system_This is normal when humidity is high_ Close
doors, windows and registers

Window vibration -- poor insta%tion_ Refer to installation instructions or check with installer

Water dripping INSIDE when unit is Improper installation, Tilt air conditioner slightly to the outside to allow water drainage Refer to
cooling, installation instructions -- check with installer

Water dripping OUTSIDE when unit is Unit removing large quantity of rnoisture from humid room_ This is normal during excessively
cooling, hurnid days