Frigidaire FAK085R7V11, FAK085R7V12, FAK085R7V13, FAK104R1V11, FAK104R1V12 Installation Guide

installation instructions

For Slider Casement Air Conditioners

NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash,

or installation in a metal CASEMENT window. Modification may be necessary when installing in windows made
differently than those shown in these instructions.

A high window accessory kit is available for window heights up to 62" (1575mm). Part # EA103W.

TABLE OF CONTENTS

SUBJECT PAGE

Meeting Electrical Requirements 1
Electrical Connection 2

Preparing For Installation 2

Installing Unit in a Sliding Window 4

Alternate Window Jamb Applications 7

Installing Unit in a Casement Window 8

Meeting Electrical Requirements

OBSERVE ALL LOCAL GOVERNING CODES
AND ORDINANCES.

DO NOT, UNDER ANY CIRCUMSTANCES,
REMOVE THE POWER SUPPLY CORD

GROUNDING PRONG,

NOTE: If codes permit, and a separate

grounding wire is used; it is recommended that a
qualified electrician determine that the grounding

path is adequate and not interrupted by plastic,
non-metallic gaskets, or other insulating materials.

RECEPTACLE WIRING
Receptacle wiring should be a minimum of 14

gauge. Use copper wire only. It is your responsibility
to provide proper and adequate receptacle wiring,

installed by a qualified electrician.

ELECTRICAL REQUIREMENTS

A 115 volt (103.5 minimum, 126.5 maximum), 60

Hertz, AC only, 15 ampere fused electrical supply
is required. Atime delay fuse or time delay circuit

breaker is also required. A separate circuit, serving

only this appliance, MUST be provided.

P/N 66129901161

Electrical Connection

Electrical ground is required on this appliance.

Recommended grounding method:
For your personal safety, this appliance must be
grounded. This air conditioner includes a power
supply cord with a 3-prong grounding plug. To
minimize possible electrical shock hazard:

-cord must be plugged into a mating 3-prong
grounding-type wall receptacle,

-must be grounded in accordance with
National Electrical Code (ANSI1NFPA70-
latest version) and

-all local codes and ordinances.
If a mating 3-prong grounding-type wall receptacle is
not available, it is the responsibility of the consumer

to have a properly grounded 3-prong wall receptacle
installed by a qualified electrician.

Preparing for Installation

3 Prong

Grounding Plug

3 Prong

Grounding Type

Wall Receptacle

Grounding

prong

Power Supply Cord

(6 feet long)

Installation Tips
For wood-frame casement windows: It may be

necessary to construct a frame, using at least 1-inch

thick wood, with a 15-1t2-inch wide opening.

For brick or cement building construction: It may
be necessary to put a wood stool strip under AC, for

mounting purposes.

Tools Required

e Flat-head screwdriver

• Phillips-head screwdriver

• Carpenter's level
e Tape measure

• Fine tooth saw
o Electric or hand drill

• Knife and scissors

• Pencil

1. Makesureyou haveallthenecessaryparts.

Installation kit contents:

1. Platform(1)

2. Supportbrace(1)

3. Adjustmentbolt(1)

4. Hexflangenut- 1/4"(1)

5. Trackseal(1)

6. Sidechannelseal(1)

7. Foamsealstrip/Sashseal

8. Safetybracket(1)
9-11.Screw-#10x2-1/2"flat-head(2),OR

Screw- #10xl-314"pan-head(2),OR
Screw- #10xl"pan-head(2)

12. Screw-#8x314"panhead(6)

13. Screw-#8-32x314"self-threading(7)

14. Windowlockingbracket(1)

15. Plasticwindowpanel(1)

16. Sidechannel(2)

17. Screw-#8x318trusshead(6)

18. Panelframelsealassembly(1)

NOTE: Use scale below to measure length of your
screws. The scale will come in handy when
separating screws for installation.

7

(13rnm) (25rnm) (44mm) (63ram)

IDENTIFY SCREWS 112" 1" 13/4" 2 1/2"

BY LENGT

3/8" 3t4" 1 1/2" 2"

(10mm)(19mrn) (28mm) (50ram)

2. Choose a proper sized window, as shown right.
15-112 inches minimum width

16-114 inches maximum width (for

casement windows)

• 21-1/4 inches minimum height (with
window panel retainer)

20-5/16 inches minimum height

(window panel retainer removed)

= 39-7116 inches maximum height

NOTE: Height measurement must be of a clear

opening above mounting platform. In some cases,
due to a variety of stop and track arrangements, the

above dimensions may vary slightly. If necessary,
installation can be made by alternating window

jambs. (See Alternate Window JambApplications.)

(continued)

k 15 /2inches

-- minimum --
width

16 /4inches

maximum

width

(casement

windows)

20 _/_ inches

minimum

height

39 _/_inches

maximum

Height

I .............