Page 1
All about the
Use & Care
of your Washer
TABLE OF CONTENTS
Important Safety Instructions ..............................2-4
Operating Instructions ......................................5-16
Care and Cleaning ..........................................17-18
Avoid Service .................................................19-20
www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352
Warranty ............................................................21
Notes .................................................................22
Français ..............................................................23
Español ..............................................................45
137409500C (1207)
Page 2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Please read all instructions before using this washer.
Recognize safety symbols, words and
labels
Safety items throughout this manual are labeled with
a WARNING or CAUTION based on the risk type as
described below:
Defi nitions
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury
or death.
DANGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury.
WARNING
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
Record Your Model and Serial Numbers
The model and serial numbers of your washer are found
on the serial plate located at the back of the tub opening
under the washer lid. Record and retain these numbers.
Model Number _____________________
Serial Number _____________________
Purchase Date _____________________
Read all instructions before using this appliance. This
book contains valuable information about:
Keep it in a safe place.
This
instructions for your washer. It also contains information
about features for several other models. Your washer
may not have every feature included.
Use the washer only as instructed in this
Guide
• Operation
• Care
• Service
Use and Care Guide
.
Product Record
provides general operating
Use & Care
CAUTION
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
IMPORTANT
IMPORTANT indicates installation, operation or
maintenance information which is important but not
hazard-related.
NOTE
Í
The instructions appearing in this
Guide
are not meant to cover every possible condition
and situation that may occur. Common sense and caution must be practiced when installing, operating and
maintaining any appliance.
Use and Care
Save these instructions for
future reference.
2
Page 3
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fi re, electrical shock, or injury to persons when using this washer, comply with the basic
warnings listed below. Failure to comply with these warnings could result in serious personal injuries.
You can be killed or seriously injured if you don’t follow these Important Safety Instructions:
PREVENT FIRE
• Do not wash items that have been previously cleaned
in, soaked in, or spotted with gasoline, cleaning solvents, kerosene, cooking oils, waxes, etc. Do not store
these items on or near the washer. These substances
give off vapors or chemical reactions that could ignite
or explode.
• Do not put oily or greasy rags or clothing on top of the
washer. These substances give off vapors that could
ignite the materials.
• Do not add gasoline, cleaning solvents, or other fl am-
mable or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.
If the hot water system has not been used for such a
period, before using the washer, turn on all hot water
faucets and let the water fl ow from each for several
minutes. This will release any accumulated hydrogen
gas. Hydrogen gas is fl ammable; do not smoke or use
an open fl ame during this time.
• Do not store or use gasoline or other fl ammable vapors
or liquids in the vicinity of this or any other appliance.
• Failure to comply with these warnings could result in
fi re, explosion, serious bodily injury and/or damage to
the rubber or plastic parts of the washer.
• Do not continue to use the washer if you hear squeaking, grinding, rubbing or other unusual noises. This
could be a sign of mechanical breakdown and lead to
fi re or serious injury. Contact a qualifi ed technician im-
mediately.
PROTECT CHILDREN
• Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer
is used near children. As children grow, teach them the
proper, safe use of all appliances.
• Destroy the carton, plastic bag and other packing materials after the washer is unpacked. Children might use
them for play. Cartons covered with rugs, bedspreads
or plastic sheets can become airtight chambers.
• Keep laundry products out of children’s reach. To prevent personal injury, observe all warnings on product
labels.
• Before the washer is removed from service or discarded, remove the washer lid to prevent accidental entrapment.
• Failure to comply with these warnings could result in
serious personal injuries.
3
Page 4
IMPORTANT SAFETY INSTRUCTIONS
Grounding type
ll receptacle
wer cord with
3-prong grgr
ounded plug
Do not,
under
y cir
cumstances,
cut,
removeve,
or b
ypass the
ounding pr
ong.
PREVENT INJURY
• To prevent shock hazard and assure stability during
operation, the washer must be installed and electrically
grounded by a qualifi ed service person in accordance
with local codes. Installation instructions are packed in
the washer for installer’s reference. Refer to
LATION INSTRUCTIONS
for detailed grounding pro-
INSTAL-
cedures. If the washer is moved to a new location, have
it checked and reinstalled by a qualifi ed service person.
• To prevent personal injury or damage to the washer,
the electrical power cord of the washer must be
plugged into a properly grounded and polarized
3-prong outlet. The third grounding prong must never
be removed. Never ground the washer to a gas pipe.
Do not use an extension cord or an adaptor plug.
• Follow package directions when using laundry products.
Incorrect usage can produce poisonous gas - resulting
in serious injury or death.
• Do not combine laundry products for use in same load
unless specifi ed on the label.
• Do not mix chlorine bleach with ammonia or acids such
as vinegar.
WARNING
FIRE/ELECTRICAL SHOCK HAZARD
Avoid fi re hazard or electrical shock. Do not use an
adaptor plug or extension cord or remove grounding
prong from electrical power cord. Failure to follow this
warning can cause serious injury, fi re or death.
PREVENT INJURY AND DAMAGE TO THE APPLIANCE
To prevent serious personal injury and damage to the
washer:
• All repairs and servicing must be performed by an authorized servicer unless specifi cally recommended in this
Use & Care Guide
. Use only authorized factory parts.
• Do not tamper with controls.
• Do not install or store the washer where it will be exposed to the weather.
• Do not install on carpet. Install washer on a solid fl oor.
It may be necessary to reinforce the fl oor to prevent
vibration or movement.
• Do not sit on, step on or stand on the washer. Do not
rest heavy loads on top. The washer is not meant to
support weight.
• To reduce the risk of electric shock, disconnect this
appliance from the power supply before attempting
any user maintenance. Canceling a cycle or turning the
power off at the console does not disconnect this appliance from the power supply.
• To prevent injury, do not reach into the washer while
parts are moving. Before loading, unloading or adding
items, push in the cycle selector knob to stop the cycle.
Allow the wash tub to coast to a complete stop before
reaching inside.
• This washer is equipped with an electrical overload protector. The washer motor will stop if it becomes overheated.
• Failure to comply with these warnings could result in
serious personal injuries.
Grounding type
wawall receptacl
PoPower cord with
3-prong
Do not,
anany cir
cut,
or b
grgrounding pr
ounded plug
under
cumstances,
remo
ypass th
ong.
WARNING
HARMFUL VAPOR HAZARD
Do not use or mix liquid chlorine bleach with other
household chemicals such as toilet cleaners, rust
removers, acid or products containing ammonia. These
mixtures can produce dangerous fumes which can
cause serious injury or death.
4
Page 5
Washing Procedures
W
H
I
T
E
S
C
A
S
U
A
L
C
O
L
O
R
S
T
O
W
E
L
S
WARNING
To reduce the risk of fi re, electric shock or injury to
persons, read these IMPORTANT SAFETY INSTRUCTIONS
in this
Use and Care Guide
1 Sort laundry into loads that
can be washed together.
• Sort items
by recommended cycle and water
temperature.
• Separate white, light and colorfast items from dark
and non-colorfast items.
• Separate items that shed lint from items that
attract lint. Casual, synthetic, knit, and corduroy items will pick up lint from towels, rugs, and
bedspreads.
• Separate heavily soiled items from lightly soiled items.
• Separate lacy, sheer, loosely knit, or delicate items
from durable items.
• Do not machine wash items containing fi berglass.
Small particles of fi berglass left in the drum may
transfer to fabrics in other loads and cause skin
irritation and/or damage to fabrics.
2 Prepare items for washing.
• Empty pockets.
before operating your washer.
OPERATING INSTRUCTIONS
• Place delicate and small items such as bras,
hosiery and baby socks in a
mesh bag.
(Mesh bag not included.)
3 Pretreat stains and heavy soil.
• See Stain Removal Guide in this
guide for safe,
successful stain
removal instructions.
4 Add a measured amount of detergent to the
wash tub before adding the laundry load.
For best results
Use a low-sudsing, high effi ciency deter-
gent to prevent oversudsing. Look for this
symbol on the detergent label:
• Follow detergent manufacturer’s directions. The
amount required depends on type of detergent,
load size and soil level, and water hardness.
5
If desired, add liquid bleach to bleach dispenser.
• Before adding the wash load, add liquid bleach to
bleach dispenser located in left front corner under
the lid:
• Brush off lint and dirt. Shake out rugs and beach
towels.
• Close zippers, fasten hooks, button buttons, tie
strings and sashes, and remove non-washable
trims and ornaments.
• Mend rips and tears to prevent further damage
during washing.
• Turn knit items inside out to prevent pilling.
• Refer to bleach manufacturer’s directions for quantity to add.
• Then add 1 cup (240 ml) water to fl ush the dis-
penser.
• Do not use powdered bleach in the bleach dispenser. Add powdered bleach to the empty tub.
5
Page 6
OPERATING INSTRUCTIONS
Washing Procedures, continued
6 Add laundry load to washer.
• For best washing performance, dry load level
should not be higher than the upper row of holes in
the wash tub. Do not overload the washer.
• Combine large and small items in a load. Load
large items fi rst. Large items should not be more
than half the total wash load.
• When washing a single heavy item, add 1 or 2
towels to balance the load.
7 If desired, add liquid fabric softener to fabric
softener dispenser.
Other Wash Products
• Water conditioner, detergent booster and enzyme
products may be added with the detergent.
IMPORTANT
Use of multi-product (detergent plus softener) sheets
or color-absorbing sheets NOT recommended. They
could disable your machine and result in unwarranted
repair costs.
8 Select the appropriate cycle and settings for
the load.
• Turn the cycle selector knob in either direction to
select the cycle desired.
• The estimated cycle time will be displayed.
• A suitable water temperature, soil level, spin speed
and options will automatically be indicated for the cycle
selected. See the “Washer Settings Chart” for more
details.
• To change the water temperature, soil level, spin
speed and water level, press the temp, soil, spin
speed or water level buttons to scroll to the
desired settings.
• To select or delete an option, press options; then,
while the indicator is blinking, press select. The
indicator will light when the option has been selected. It will no longer be lighted when the option
has been deleted.
• Add liquid softener to the dispenser, following fabric softener label directions. DO NOT use granular
detergent in this dispenser.
• DO NOT fi ll above the maximum fi ll line.
• Turn fabric softener option on.
• Do not use bleach in this dispenser.
NOTE
Í
To prevent staining, do not overfi ll the “FABRIC
SOFTENER” chamber or pour liquid fabric softener
directly on the wash load.
6
NOTE
Í
If a setting is not available for the cycle selected, the
indicator will not light.
Page 7
Washing Procedures, continued
OPERATING INSTRUCTIONS
• Adjustments made to a cycle will be remembered
and recalled each time that cycle is selected in the
future.
To return to factory settings,
press these two buttons at
the same time and hold until
the signal sounds.
9 Start the cycle.
• Close the washer lid. The washer will not operate
with the lid open.
• Push in or turn the cycle selector knob or turn any
option knob to “wake” the washer. You will hear
three beeps to indicate washer is ready to operate.
• After making your selections, push in the selector
knob to start the cycle. You will hear one beep and
the washer lid will lock.
• Select delay start to delay the beginning of the
cycle, if desired.
• To add a forgotten item to the wash tub, push in
the cycle selector knob to pause the cycle. You will
hear two beeps. After the lock releases, lift the lid
and add the item. Close the lid and push in the
selector knob again, continuing the current cycle.
• To cancel a running cycle, push in and hold the
cycle selector until the washer discontinues running.
• A signal will sound at the end of the cycle if the
chime option has been selected.
10 Remove items when the cycle is completed.
• For your safety, the lid is locked during the operation
of the washer. It will unlock at the cycle end after the
tub has come to a complete stop.
SAFETY LID LOCK
• To open the lid during cycle operation, push in the
cycle selector knob to pause the cycle. You will hear
two beeps. Wait for the lid lock to release. Do not
force open the locked lid.
CAUTION
To avoid serious personal injury, do not operate washer
if safety lid lock is missing, damaged or operating
improperly.
• Place washed items in automatic dryer, line dry, or
dry fl at as directed by fabric care label. Excess wrin-
kling, color transfer or odors may develop in items
left in the washer after the cycle has ended.
For best results
Follow the fabric care label instructions
on items to be washed.
7
Page 8
OPERATING INSTRUCTIONS
push to start | push to pause | push & hold to cancel
hot
warm
cool
cold
cold water clean
stain treat
heavy
light
extra light
energy saver
wrinkle release
freshwater ri nsenormal
chime
fabric softener
presoak
rinse & spin
drain & spin
whites
select
casual
normal
kids wear
comforter
quick washwool
heavy duty
delicates
bedding
jeans
estimated time
remaining
max auto
high
no spin
spin speed water leveldelay startoptionssoil leveltemp
max
normalnormal
lowlow
min
sensing add a garment final spin clean
This manual covers many models and not all cycles, options, or features listed are available on every model. Consoles shown above
for reference only. Your model may differ.
Cycle Selection
Turn the cycle selector in either direction to the cycle
desired.
For best results
Follow the fabric care label
instructions on items
to be washed.
Once a cycle is running, turning the selector knob to
another selection will not change the cycle. If cycle
selection change is attempted after the cycle starts, the
indicator lights will fl ash and a signal will beep, but the
original cycle will continue.
NOTE
Í
To change the cycle selection once the cycle has
begun, push in and hold the cycle selector knob to
cancel the current cycle, make the new selection and
push in the selector knob again to restart the washer.
wash
normal
Use this load for light to normally soiled cottons,
towels, shirts, denims and mixed loads.
comforter
Add one large comforter or two light-duty sleeping
bags to the comforter cycle. Press the item(s) to the
bottom of the tub as much as possible to prevent them
from fl oating as the tub fi lls with water.
heavy duty
Use this cycle for heavily soiled, durable garments - ex.
towels, sports gear, or fabric tote bags. For best soil
and stain removal, use the hottest water safe for the
fabrics being washed.
delicates
Use this cycle for lightly soiled knits and delicates which
require gentle washing.
bedding
This cycle is designed for large items such as blankets,
sheets, mattress pads, duvet covers and similar items.
jeans
Select this specialty cycle for washing an entire load
of lightly to normally soiled denim jeans or similarlycolored cotton khakis.
8
Page 9
OPERATING INSTRUCTIONS
Cycle Selection, continued
quick wash
Quickly wash a small, lightly soiled.
kids wear
Wash normally-soiled kids wear and baby wear with
this specialty cycle.
wool
Designed for a small load of machine-washable woolen
items, the wool cycle uses gentle washing action along
with cold rinses to eliminate shrinking and damage to
wool. You may use an wool detergent approved for
automatic washers.
whites
Use this cycle for white fabrics and lightly colored
clothing. Refer to fabric care label for use of liquid
chlorine bleach. Hot water is recommended to ensure
optimal bleach activation. For peak rinsing performance
and to avoid chlorine residues on your laundry add
fresh rinse to this cycle.
drain & spin
Use the drain & spin cycle anytime you want to drain
water from the washer and spin out the load.
rinse & spin
Select rinse & spin for loads that need a cold water
rinse or to add fabric softener that may have been
omitted in a regular cycle.
presoak
Use this cycle to soak heavily soiled and stained items
before washing. Any temperature except hot may be
selected, but cold water is recommended with this cycle
as warmer water may set some stains. Use the amount
of detergent recommended for a normal wash cycle. If
desired, use a bleach or a soaking agent safe for the
fabric. The washer will drain at the end of the cycle.
Cycle Settings
For best results
Follow the fabric care label instructions
on items to be washed.
Appropriate wash water temperature, soil level, spin
speed, water level and options will automatically be
displayed for each cycle. The settings can be modifi ed
before the cycle is started. Make modifi cations according
to fi ber content, colorfastness and soil level. Modifi cations
for each cycle will be remembered and recalled each time
that cycle is selected in the future.
To return to factory settings,
press these two buttons at
the same time and hold until
the signal sounds.
If changes are attempted after the cycle starts, the
lights will fl ash and a signal will beep, but the cycle will
continue.
NOTE
Í
To change the settings once the cycle has begun, push
in the cycle selector knob to pause the cycle, make the
new selections and push in the selector knob again to
restart the washer.
NOTE
Í
Follow presoak with a complete wash cycle suitable
for the load using a half dose of detergent.
casual
Use this cycle for poly blends with a permanent press
or no-iron fi nish.
9
Page 10
OPERATING INSTRUCTIONS
Cycle Settings, continued
Wash Water Temperature
To change the preset temperature, press the temp
button to scroll to the desired setting. To protect your
fabrics, the temperature range from low to high settings
may be different depending on cycle selected.
The water heater setting and its distance from the
washer, water usage in other parts of the home, and
seasonally low ground water temperature in some
geographic areas can affect water temperature.
hot
Use this setting for heavily soiled white or colorfast
cottons and blends.
warm
Use this setting for normally soiled white or colorfast
cottons or blends.
cool
Use this setting for normally soiled sheets, casual items
and washable woolens.
cold
Some warm water will automatically blend with cold tap
supply to achieve cold. Use this setting for lightly soiled
non-colorfast items, knits, delicates, and hand washables.
cold water clean
Wash and rinse temperatures are equivalent to
temperature of cold tap supply. Use this selection for
fabrics and colors that are prone to dye transfer. For
use with cold water detergents.
Spin Speed
Max, high, normal and low spin speeds are available
for most cycles. The spin speed and/or duration of fi nal
spin may vary from model to model and cycle to cycle.
Increasing the spin speed will extract more water,
decrease drying time and conserve energy. Decreasing
the spin speed will reduce wrinkling.
Select low spin speed to gently spin items that should be
line dried.
Use no spin to omit the fi nal spin at the end of the cycle.
The load will be very wet. Remove items from the wash
drum to drip dry or select a drain & spin or rinse &
spin cycle to remove excess water at a more convenient
time.
Water Level
Press the water level button to select a water level
appropriate for the load size. For best results, DO NOT
overload. Add items loosely to the tub. The dry load
should not be higher than the top row of holes in the
wash tub. There should be enough water in the tub for
items to move freely.
NOTE
Í
Water level is automatically calculated by the washer
in the auto setting. The washer will perform a dry load
sensing procedure before adding water to the tub. The
sensing indicator light will be lit.
Soil Level
Adjust duration of agitation time based on the soil level of
each load. Heavy, normal, light, extra light soil levels
are available. Stain treat gives your cycle the agitation
time of a heavy selection plus the added benefi t of a mid
agitation soak.
10
Page 11
Cycle Options
To select an option, press options until the indicator
for the desired option fl ashes, then press select. If an
option is not available for a cycle, the indicator will not
light. Follow the same steps to delete an option.
Occasionally, a setting and option in the same cycle will
confl ict with each other, like energy saver and fresh
water rinse. When this happens, the option selected
fi rst will cause the confl icting option to not be selectable.
energy saver
The energy saver option reduces water temperature
to save energy, lowers water usage slightly and also
extracts more water to reduce drying time.
wrinkle release
Wrinkle release adds a deep rinse with warm water
to relax existing wrinkles and then lowers the speed of
the fi nal spin to prevent setting new ones.
freshwater rinse
Use this option when additional rinsing is desired to
remove excess dirt and detergent. It is recommended
for heavily soiled loads or if household members have
sensitive skin.
chime
A signal will sound at the end of the cycle if this option
is selected.
fabric softener
You must turn the fabric softener switch to the “on”
position for correct operation of the fabric softener
dispenser. See
procedures.
delay start
Press delay start to select a wash time convenient
to your schedule or during off peak energy hours. The
delay time selected will be displayed and begin counting
down when you push in the cycle selector knob to start
the unit.
Care and Cleaning
for dispenser cleaning
OPERATING INSTRUCTIONS
NOTE
Í
To change options once the cycle has begun, push in
the cycle selector knob to pause the cycle, make the
new selections and push in the selector knob again to
restart the washer.
11
Page 12
OPERATING INSTRUCTIONS
Other Features
Control Lock
To avoid having someone accidentally start or stop the
washer, press options and select at the same time and
hold for 10 seconds. If you attempt to activate the washer
while it is locked, the display will fl ash and error beeps
will sound. To remove the control lock, press options and
select again.
Estimated Time Remaining
The estimated cycle duration will be displayed before you
start the cycle and time remaining will be displayed after
you start the cycle. Out-of-balance situations during spins
may occasionally lengthen actual cycle times.
Load Size Sensing
Water level is automatically calculated by the washer
in the auto setting. The washer will perform a dry load
sensing procedure to determine load size before adding water to the tub. If your model has status lights, the
sensing indicator will be lit.
warm
cool
cold
cold water clean
normal
kids wear
comforter
quick washwool
heavy duty
delicates
bedding
jeans
estimated time
remaining
max aut o
high
no spin
spin speed water leveldelay startoptionssoil leveltemp
max
normalnormal
lowlow
min
hot
light
extra light
wrinkle release
heavy
freshwater rinsenormal
chime
fabric softener
energy saver
stain treat
casual
presoak
rinse & spin
drain & spin
whites
select
Press and hold both for ten seconds
to lock or unlock the controls.
Status Lights
The following indicators may be lighted during the cycle:
• sensing
• add a garment
• wash
• fi nal spin
• clean
12
Page 13
OPERATING INSTRUCTIONS
Washer Settings Chart
These Temperatures, Soil levels, Spin Speeds, Water levels and Options are available with the following cycles:
casual
normal
comforter
heavy duty
delicates
bedding
jeans
quick wash
1
temp
hot
warm
cool
cold
cold water clean
soil level
stain treat
heavy
normal
light
extra light
spin speed
max
high
normal
low
no spin
water level
auto
max
normal
low
min
options
energy saver
wrinkle release
freshwater rinse
chime
fabric softener
delay start
9 = Available selections. = Cycle defaults. = Non-modifi able presets.
99
99
9
999
9
999
9
999
999 99 9 9
9999 99 999
9999
99
99
999 9 9 999
999 9
9
999
9
99 9999999
99 9
99999999999 99
99999999999 99
99999999999 99
99999999999 99
99999999999 99
9
9
9
9
99999999999
99999999999999
99999999999
99999999999999
9
9
9
99
9
9
9
9
9
9
9999
99 999
9
99
9
9
9
9
9
9
9
9
9
9
99
9
9
9999 9
9999 9
9
999
9
9
999
9
9
9 999
999 9
999999999
kids wear
9
9
9
wool
whites
9
9
999
99
drain & spin
rinse & spin
9
9
presoak
9
9
9
13
Page 14
OPERATING INSTRUCTIONS
Safe Stain Removal Procedures
To reduce the risk of fi re or serious injury to persons or
property, comply with the basic warnings listed below:
• Read and comply with all instructions on stain removal products.
• Keep stain removal products in their original labeled
containers and out of children’s reach.
• Thoroughly wash any utensils used.
• Do not combine stain removal products, especially
ammonia and chlorine bleach. Dangerous fumes can
result.
• Never wash items which have been previously
cleaned in, washed in, soaked in or spotted with
gasoline, dry cleaning solvents or other fl ammable
or explosive substances because they give off vapors
that could ignite or explode.
• Never use highly fl ammable solvents, such as gaso-
line, inside the home. Vapors can explode on contact
with fl ames or sparks.
For Successful Stain Removal:
• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain removal chart on the
next page.
• To pretreat stains, use a prewash product, liquid
detergent, or a paste made from powder detergent
and water.
• Use cold water on unknown stains as hot water can
set stains.
• Consult care label instructions for treatments to avoid
on specifi c fabrics.
• Check for colorfastness by testing stain remover products on an inside seam.
• Rinse and wash items after stain removal.
WARNING
HARMFUL VAPOR HAZARD
Do not use or mix liquid chlorine bleach with other
household chemicals such as toilet cleaners, rust
removers, acid or products containing ammonia. These
mixtures can produce dangerous fumes which can
cause serious injury or death.
For best results
Follow the fabric care label instructions
on items to be washed.
14
Page 15
Stain Removal Suggestions
OPERATING INSTRUCTIONS
STAIN
Adhesive tape, chewing
gum, rubber cement
Baby formula, dairy
products, egg
Beverages (coffee, tea,
soda, juice, alcoholic
beverages)
Blood Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing
Candle wax, crayon Scrape off surface wax. Place stain face down between paper towels. Press with warm
Chocolate Pretreat or soak in warm water using product containing enzymes. Wash using bleach
Collar or cuff soil, cosmetics
Dye transfer on white
fabric
Grass Pretreat or soak in warm water using product containing enzymes. Wash using bleach
Grease, oil, tar (butter, fats, salad dressing,
cooking oils, car grease,
motor oils)
Ink Some inks may be impossible to remove. Washing may set some inks. Use prewash stain
Mildew, scorch Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water
Mud Brush off dry mud. Pretreat or soak with product containing enzymes.
Mustard, tomato Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Nail polish May be impossible to remove. Place stain face down on paper towels. Apply nail pol-
Paint, varnish WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it
Perspiration Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach
Rust, brown or yellow
discoloration
Shoe polish LIQUID: Pretreat with a paste of powder detergent and water. PASTE: Scrape residue
Tomato Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Urine, vomit, mucus,
feces
Wine Pretreat or soak in cold water. Wash in hottest water and bleach safe for fabric
TREATMENT
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or nonfl ammable dry cleaning fl uid.
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more.
Wash.
Pretreat stain. Wash using cold water and bleach safe for fabric.
enzymes. Wash using bleach safe for fabric.
iron until wax is absorbed. Replace paper towels frequently. Treat remaining stain with
prewash stain remover or nonfl ammable dry cleaning fl uid. Hand wash to remove sol-
vent. Wash using bleach safe for fabric.
safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.
safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy
stains and tar, apply nonfl ammable dry cleaning fl uid to back of stain. Replace towels
under stain frequently. Rinse thoroughly. Wash using hottest water safe for fabric.
remover, denatured alcohol or nonfl ammable dry cleaning fl uid.
before washing. Badly mildewed fabrics may be permanently damaged.
ish remover to back of stain. Repeat, replacing paper towels frequently. Do not use on
acetate fabrics.
cannot be removed. OIL BASED AND VARNISH: Use solvent recommended on can label.
Rinse thoroughly before washing.
in hottest water safe for fabric.
Use rust remover safe for fabric. Do not use chlorine bleach because it may intensify
discoloration.
from fabric. Pretreat with prewash stain remover or nonfl ammable dry cleaning fl uid.
Rinse. Rub detergent into dampened area. Wash using bleach safe for fabric.
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.
15
Page 16
OPERATING INSTRUCTIONS
Common Washing Problems
Many washing problems involve poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory washing
results, follow these suggestions provided by The Soap and Detergent Association.
PROBLEM POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES
Blue stains • Undiluted liquid detergent
Discoloration,
graying
Greasy, oily
stains
Holes, tears, or
snags
Lint • Incorrect sorting.
Pilling
(Fibers ball up
and cling to
fabric.)
Residue or
powder on dark
items;
Stiff, harsh
fabrics.
Wrinkling • Overloading the washer.
Yellow buildup
of body soil on
synthetic fabrics
Yellow or brown
rust stains
or fabric softener dispensed
directly onto fabric.
• Not enough detergent.
• Wash water temperature too
low.
• Incorrect sorting.
• Not enough detergent.
• Undiluted liquid fabric softener poured directly on fabric.
• Incorrect use of chlorine
bleach.
• Unfastened zippers, hooks,
buckles.
• Rips, tears and broken threads.
• Overloading the washer.
• Degradation of fabric.
• Tissues left in pocket.
• Overloading the washer.
• Not enough detergent.
• Undissolved detergent has left
a residue resembling lint.
• Static cling is attracting lint.
• Load washed too long.
• Pilling is normal with synthetic
and permanent press fabrics.
This is due to abrasion from
normal wear.
• Undissolved detergent.
• Some granular detergents
can combine with hard water
minerals to form a residue.
• Overloading the washer.
• Incorrect wash cycle for wash
load.
• Agitation time too short.
• Wash water temperature too
low.
• Not enough detergent.
• Iron or manganese in water
supply, water pipes, or water
heater.
• If caused by detergent, mix 1 cup (240
ml) white vinegar with 1 quart (.95 L)
water in a plastic container. Soak item 1
hour. Rinse.
• If caused by fabric softener, rub stains
with bar soap. Wash.
• Rewash with correct amount of detergent and hottest water safe for fabric.
• Add bleach safe for fabric.
• Treat with prewash stain remover or
liquid detergent.
• Increase detergent and water temperature. Rewash.
• Rub fabric softener stains with bar soap.
• May be irreversible if rips, tears and
seams cannot be mended.
• Reduce load size. Rewash using correct
water temperature, water level, and
amount of detergent.
• Add nonprecipitating water conditioner to
wash water to remove detergent residue.
• Add liquid fabric softener to fi nal rinse.
• Dry load in dryer.
• Remove lint with lint brush or roller.
• Use a lint brush or shaver to remove
pills.
• Rewash load. • Increase water temperature using
• Reduce load size.
• Rinse in cold water with liquid fabric
softener using the casual or delicate
cycle.
• Soak in detergent booster or product
containing enzymes.
• Wash in hottest water safe for fabric using casual cycle.
• Increase detergent.
• Add bleach safe for fabric or treat with
color remover.
• To restore discolored load of whites, use
rust remover safe for fabric.
• Do not use chlorine bleach to remove
rust stains. It may intensify discoloration.
• Add detergent to empty tub. Do not
pour on dry load.
• Avoid overfi lling fabric softener
compartment of dispenser.
• Sort items by soil level and color.
• Use correct amount of detergent,
hottest water and bleach safe for
fabric.
• Use correct amount of detergent
and hottest water safe for fabric.
• Do not pour liquid fabric softener
directly on fabric. See Operating
Your, step 5.
• Never pour chlorine bleach directly
on fabric.
• Check condition of items before
washing. See Operating Your, steps
2 and 5.
• See Washing Procedures, steps 1
and 2.
• Do not overload washer.
• Use correct temperature and
amount of detergent, water and
wash time.
• Use fabric softener in the washer to
lubricate fi bers.
• When ironing, use spray starch or
fabric fi nish on collars and cuffs.
• Turn items inside out to reduce
abrasion.
hottest water safe for fabric.
• Do not overload washer.
• Use liquid detergent or use nonprecipitating water conditioner with
powder detergent.
• Do not overload washer.
• Remove items from washer as soon
as cycle is completed.
• Use liquid fabric softener.
• Select correct wash cycle.
• Use correct amount of detergent.
• Wash synthetics frequently using
hot or warm water.
• Use nonprecipitating water softener.
• Before washing, run hot water for a
few minutes to clear lines.
• Drain water heater occasionally.
• For an ongoing problem, install
an iron fi lter in your water supply
system.
16
Page 17
Cleaning Instructions
NOTE
Í
Fabric softener may build up in the dispenser well.
Residue should be removed once or twice a month.
a
b
Orient correctly
for reinsertion.
CARE AND CLEANING
INSIDE
• Remove items from the washer as soon as the cycle
ends. Excess wrinkling, color transfer, and odors may
develop in items left in the washer.
• Dry the washer top, the area around the lid opening,
and the underside of the lid. These areas should always
be dry before the lid is closed.
• Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock hazards.
• When extremely soiled items have been washed, a dirty
residue may remain on the tub. Remove this by wiping
the tub with a nonabrasive household cleanser. Rinse
thoroughly with water.
• The base plate or tub may become stained from fabric
dye. Clean these parts with a nonabrasive household
cleanser. This prevents dye transfer to future loads.
FABRIC SOFTENER DISPENSER
• Remove the dual chamber insert (a) from the bleach
and fabric softener dispenser by pinching at the chamber divider and lifting upward. Also remove the siphon
cap (b).
• Rinse the insert and cap with a combination of ¾ cup
liquid chlorine bleach and 1 gallon hot tap water to
remove any buildup. Large amounts of fabric softener
residue may indicate improper dilution or more frequent cleaning is required. Rinse well with tap water.
• For the dispenser well, use a small brush to clean the
recesses. Remove all residue.
• Replace the siphon cap and insert by pressing it in
place until you hear a slight click.
IMPORTANT
Do not store or place laundry products on top of washer
at any time. They can damage the fi nish or controls.
OUTSIDE
• When washing is completed, wipe top and sides of
washer with a damp cloth. Turn water faucets off to
prevent pressure build-up in the hoses.
• Clean the cabinet with mild soap and water. Never use
harsh, gritty or abrasive cleansers
• If the cabinet becomes stained, clean with diluted
chlorine bleach (1 part bleach to 8 parts water). Rinse
several times with clear water.
• Remove glue residue from tape or labels with a mixture
of warm water and mild detergent. Or, touch residue
with the sticky side of tape.
• Before moving the washer, place a strip of cardboard or
thin fi berboard under the front leveling legs to prevent
damage to the fl oor .
17
Page 18
CARE AND CLEANING
Winterizing Instructions
IMPORTANT
If the washer is stored in an area where freezing can
occur or moved in freezing temperatures, follow these
winterizing instructions to prevent damage to the
washer:
1 Turn off water supply faucets.
2 Disconnect hoses from water supply and drain
water from hoses.
3 Plug electrical cord into a properly grounded
electrical outlet.
4 Add 1 gallon (3.8 L) nontoxic recreational vehicle
(RV) antifreeze to empty wash tub. Close lid.
5 Select the drain & spin cycle. Start the cycle
and let the washer drain for 1 minute to drain out
all the water. Not all of the RV antifreeze will be
expelled.
6 Stop the cycle, unplug electrical power cord, dry off
tub interior and close the lid.
7 Store washer in an upright position.
8 To remove antifreeze from washer after storage,
run empty washer through a complete cycle using
detergent. Do not add wash load.
RV
ANTIFREEZE
Follow WINTERIZING
INSTRUCTIONS for
cold weather storage
and care.
18
Page 19
AVOID SERVICE CHECKLIST
Before calling for service, review this list. It may save both time and expense. The list includes common occurrences
that are not the result of defective workmanship or materials in this washer.
OCCURRENCE POSSIBLE CAUSE SOLUTION
NOISE
Rattling and clanking
noise.
Thumping sound. Heavy wash loads may produce a thumping sound.
Squealing sound or hot
rubber odor.
Vibrating noise. Washer is not resting fi rmly on fl oor. Move washer so it rests fi rmly on fl oor. Adjust leveling legs. See
OPERATING
Washer does not start. Washer lid is open. Close washer lid. The washer will not operate when the lid is open.
Washer won’t spin. Lid is not completely closed. Close washer lid. The washer will not operate when the lid is open.
Residue left in drum. Heavily soiled items. Wipe tub with a nonabrasive household cleanser, then rinse. Shake
Foreign objects such as coins or safety pins may be
in tub or pump.
Belt buckles and metal fasteners are hitting wash
tub.
This is usually normal. If sound continues, washer is
probably out of balance.
Washer is overloaded. Do not overload washer. Stop washer and reduce load.
Shipping bolt has not been removed during installation. See INSTALLATION INSTRUCTIONS for removing shipping bolt.
Wash load unevenly distributed in tub. Stop washer and rearrange wash load.
Electrical power cord may not be plugged in or connection may be loose.
House fuse blown, circuit breaker tripped, or a
power outage has occurred.
Water supply faucets are not turned on. Turn on water supply faucets.
Motor is overheated. Washer motor will stop if it
becomes overheated.
Stop washer and check drum. If noise continues after washer is
restarted, objects may be in pump. Call your authorized servicer.
To prevent unnecessary noise and damage to tub, fasten fasteners and turn items inside out.
Stop washer and redistribute wash load.
INSTALLATION INSTRUCTIONS for details.
Make sure plug fi ts tightly in wall outlet.
Reset circuit breaker or replace fuse. Do not increase fuse
capacity. If problem is a circuit overload, have it corrected by
a qualifi ed electrician. If problem is a power outage, call local
electric company.
Wait for the motor to cool down before attempting to restart.
or brush excess dirt and sand from items before washing
19
Page 20
AVOID SERVICE CHECKLIST
OCCURRENCE POSSIBLE CAUSE SOLUTION
WATER
Wash load too wet after
spin.
Water does not enter
washer or it enters slowly.
Water level does not
cover load.
Warm or hot water is not
hot enough.
Water in washer does not
drain or drains slowly.
Water leaks. Loose fi ll hose connection at faucet or washer. Check and tighten hose connections. Ensure rubber sealing
Incorrect wash and rinse
temperatures.
Water is entering washer
but tub does not fi ll.
Water is present in tub after
wash cycle is complete.
The drain and spin cycles
did not occur.
Washer is overloaded. Do not overload washer. See Washing Procedures.
Load is out of balance. Rearrange load to allow proper spinning.
Drain hose is kinked. Straighten drain hose.
Washer lid is open.
Water supply is not adequate in area. Check another faucet in the house. Wait until water supply and
Water supply faucets are not completely open. Fully open hot and cold faucets.
Water is being used elsewhere in the house. Water pressure must be at least 10 psi (69 kPa). Avoid running
Water inlet hoses are kinked. Straighten hoses.
Improper water level selection (for models with
water level/load size control).
Washer is overloaded. Do not overload washer.
Hot water heater is set too low or is a distance
from washer.
Hot water is being used elsewhere in the house. Avoid using hot water elsewhere before or during washer use.
Drain hose is kinked or clogged. Clean and straighten the drain hose.
House drain pipes are clogged. Unclog drain pipes. Contact plumber if necessary.
Hot and cold water hoses are connected to wrong
supply faucets.
Drain hose standpipe is incorrect height. Standpipe must be a minimum of 33” (83.82 cm) high to pre-
Lid lock malfunction. Do not bypass lid lock. Call your authorized servicer.
Lid lock malfunction. Do not bypass lid lock. Call your authorized servicer.
Close washer lid. The washer will not operate when the lid is open.
pressure increase.
water elsewhere while washer is fi lling.
Select higher water level/load size.
Measure hot water temperature at nearby faucet with candy
or meat thermometer. Water temperature should be at least
120°F (50°C). Adjust water heater as necessary.
There may not be enough hot water available for proper cleaning. If problem persists, your hot water system may be unable
to support more than 1 use at a time.
washers are installed.
Connect hot water hose to hot water faucet and cold water
hose to cold water faucet.
vent siphoning. See INSTALLATION INSTRUCTIONS.
20
Page 21
MAJOR APPLIANCE WARRANTY INFORMATION
For the applicable warranty period as set forth below, as measured from your original date of purchase, Electrolux will repair or
replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and
maintained in accordance with the provided instructions.
Warranty Periods:
• All parts — One year including labor
• Wash tub — Functional life of the product (excluding labor)
• Wash tub drive motor, non-cosmetic defects — Ten years (excluding labor)
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary
household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a
part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air fi lters, water fi lters, other consumables, or knobs, handles, or other
cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage
expense for service calls to remote areas, including the state of Alaska.
12. Damages to the fi nish of appliance or home incurred during installation, including but not limited to fl oors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux
parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse,
inadequate power supply, accidents, fi res, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS
PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE
YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND
INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY.
SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE.
IF YOU NEED SERVICE
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be
required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be
obtained by contacting Electrolux at the addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North
America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux
authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty
must be performed by Electrolux or an authorized service company. Product features or specifi cations as described or illustrated are
subject to change without notice.
USA
1.800.944.9044
Electrolux Major Appliances
10200 David Taylor Drive
Charlotte, NC 28262
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
21
Page 22
NOTES
22
Loading...