Frigidaire FAFW3001LW6, FAFW3001LW7, FFFW4000QW0 Installation Guide

TABLE OF

Important Safety InstructLons .............................. 2-3

Installation Requlrements .................................. 4-6

Installat_on Instructlons .................................... 7-10

Accessories ..........................................................

CONTENTS

Notes .............................................................. 12

Franr=als ............................................................ 13

Espafi01 .............................................................. 25

Shipping Hardware

{3 Foam shipping support (under wash tub)

removed and stored

Recognize safety symboisr words and labels

Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described below:

Definitions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards, Obey all safety messages that follow this symbol to avoid possible injury

or death.

....................................................................................... drain hose

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious {3 Drain hose secured in place with cable tie

in!uEx:........................................................................................................................................................(shipped in drum)

CAUTION indicates a potentially hazardous situation {3 Washer plugged in which, if not avoided, may result in minor or moderate

injury. Final Checks

{3 Shipping bolts and spacers removed from rear

of appliance and stored

[3 Hole plugs (shipped in bag in drum) installed in

holes in backsheet

Leveling

{3 Washer is level, side-to-side and front-to-back {3 Cabinet is setting solid on all corners

Water Supply

washers are installed

{3 HOT supply is connected to HOT inlet and

COLD supply is connected to COLD inlet

{3 Use only new hoses and verify rubber sealing {3 HOT and COLD water supply turned on

{3 No leaks present at water supply connections

or appliance inlet connections - recheck in 24 hours

Drain

{3 Stand pipe or wall drain height minimum 24" {3 Anti-siphon disc (shipped in drum)installed on

Electrical Power

{3 House power turned on

{3 InstallaUon InstrucUons and Use and Care

Gu,dereadthorough,y

IMPORTANT indicates installation, operation or {3 Door locks and water enters drum when cycle maintenance information which is important but not starts

hazard-related. {3 Registration card sent in

ii!ii:ii!iiii!!i_iiiii_i_ii_iii_ii_!i!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!iiii!i!ii!i!i!!ii!i!i!i!i!i!i!i!i!i!ii!i!i!iiiii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!!!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!!

The electrical service to the washer must conform with local codes and ordinances and the latest edition of the

National Electrical Code ANSI/NFPA 70 or in Canada the Canadian Electrical Code C22.1 part 1.

Destroy the carton and plastic bags after the washer is unpacked. Children might use them for play. Cartons

covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a garbage container or make materials inaccessible to children.

Save these instructions for future reference,

For your safety the information in this manual must be

followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life, Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

installing, operating and maintaining any appliance. Maximum benefits and enjoyment are achieved

when all the Safety and Operating Instructions are understood and practiced as a routine with your

laundering tasks.

Tools and materials needed for installation:

OR OR

Adjustable 3/8"or ] 0 mm Ratchet and

wrench box wrench socket set

Inlet hose (x2)

AND

Adjustable

pliers

AND

Carpenter'slevel

Electrical system requirements

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2 wire, with ground, 120 volt single

phase, 60 Hz, Alternating Current.

Because of potentially inconsistent voltage capabilities, the use of this washer with power created by gas

powered generators, solar powered generators, wind powered generators or any other generator other than

the local utility company is not recommended.

OUTLET RECEPTACLE- Properly grounded 3-prong

receptacle to be located so the power supply cord is

accessible when the washer is in an installed position.

Groundin_ wall

Power €ord With B-preng greunded plug

GFI (Ground Fault Interrupter) receptacle is not required.

Ground requirements

Water supply requirements

Hot and cold water faucets MUST be installed within hose

length of your washer's water inlet. The faucets MUST be 3/4 inch (1.9 cm) with threading for laundry hose

connection. Water pressure MUST be between 30 and

120 psi. Pressure difference between hot and cold cannot be more than i0 psi. Your water department can advise you of your water pressure.

Drain system requirements

1 Drain capable of eliminating 17 gals (64.3 L) per

minute.

2 A standpipe diameter of i-i/4 in. (3.18 cm)

minimum.

3 The standpipe height above the floor should be:

Minimum height: 24 in. (6! cm) Maximum height: 96 in. (244 cm)

96"

(244cm) Illl

max.

¸I

Drain hose attached to the washer can reach a 74 in. (i88 cm) high standpipe. For higher standpipe, use

hose P/N 137098000, available from an authorized

parts distributor.

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

1 The washer MUST begrounded. In the event of

malfunction or breakdown, grounding will reduce

the risk of electrical shock by a path of least

resistance for electrical current.

2 Since your washer is equipped with a power supply

cord having an equipment-grounding conductor and a grounding plug, the plug MUST be plugged

into an appropriate, copper wired receptacle that is properly installed and grounded in accordance with

all local codes and ordinances or in the absence of local codes, with the National Electrical Codes,

ANSI/NFPA 70 (latest edition). If in doubt, call a

licensed electrician. DO NOT cut off or alter the

grounding prong on the power supply cord. In situations where a two-slot receptacle is present,

it is the owner's responsibility to have a licensed

electrician replace it with a properly grounded three

prong grounding type receptacle.

Clearance requirements

INSTALL YOUR WASHER:

1 In an area exposed to dripping water or outside

weather conditions, The ambient temperature should never be below 60° F (i5,6 ° C) to

maximize detergent effectiveness.

2 In an area (garage or garage-type building)

where gasoline or other flammables (including automobiles) are kept or stored.

3 On carpet, Floor MUST be solid with a maximum

slope of 1 inch (2.5 cm). To minimize vibration or movement, reinforcement of the floor may be necessary.

Installation in a Recess or Closet

If washer and dryer are installed in the same closet, door ventilation is required: A minimum of 120 square inches (774,2 cm 2) of opening, equally divided at the top

and bottom of the door, is required. Louvered openings should be located 3 inches (7,6 cm) from bottom and top of door. Air openings are required to be unobstructed when a door is installed. A Iouvered door with equivalent

air openings for the full length of the door is acceptable.

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0"(0 cm) 0" (0 cm)* 0" (0 cm) n/a Under- 0"(0 cm) 0" (0 crn)* 0" (0 cm) n/a

Counter Closet 0" (0 cm) 0" (0 cm)* 0" (0 cm) 1" (2.5 cm)

1',

o..---_',',_,--

(25cm) (Ocm)

iii1

closet door

Washer Dimensions

_49.5" (126 cm) _

to clear open door

freestand washer

on floor

floorline

washer mounted on

optional pedestal

floorline

27,8" (

to front of closed door

water supply connection on rear of unit

27.0"

(6815 cm)

51,25"

(130 cm)

_50.8"(129 cm)*

to clear open door

_29.75"(75.5 cm)*_

to front of closed door

71.5"

(182 cm)

water supply connection

rear of unit

of gas unit

floorline

_Connection of water inlet hose on steam dryer adds 3/4 in, (2 cm) to installation depth. 1Power supply cord length on washer approximately 60 inches (152.5 cm), 2Drain hose length on washer approximately 52 inches (132 cm), 3Power supply cord length on gas dryer approximately 60 inches (152.5 cm).

37"

(94 cm)

electrical supply on

rear of uniP

centerline height for

drain hose

_r of

unit 2

39"

(99 cm)

Removing foam packaging

Destroy the carton and plastic bags after the washer is

unpacked.Chitdrenmightusethemforplay,Cartons

covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation, Place

aJtmaterials in a garbage container or make materials

inaccessibletochildren,

1 Temporarily remove door tape. 2 Open washer door and remove everything from the

drum.

3 Close door and reapply door tape. 4 Using a rug, blanket or piece of cardboard to

protect the floor, carefully lay the washer on it's

back.

To avoid back or other injury have more than one person move or Iift the washer.

Save styrofoam base and shipping plug for useto help prevent washer damage during any future moves.

EXCESSIVE WEIGHT HAZARD

5 Remove styrofoam base and shipping plug and set

them aside. 6 Carefully return the washer to an upright position. 7 Carefully move the washer to within 4 feet (1 m) of

its final location.

Removing shipping hardware

Rubber expansion material on spacers may need time to relax before they can be easily pulled through

-.... shipping hole.

]

, X2

' II

i / _x4

:/ / ,×4

Remove all of the following:

4 BOLTS O 4 SPACERS

[] 2 P CLAMPS

Installing hole plugs

" :............'..... {:_, <{t_<<<<:::::::::::: <9._......,

[] 2 P CLAMPS O 4 SPACERS

Save all shipping bolts and spacers for future use. If the washer is to be transported at a later date, the

shipping hardware must be reinstalled to help prevent

sh!pp!ng damage: ..........................................................................................................................................................

A 4 HOLE PLUGS

(IN BAG)

with washer instruction guides. Insert them in

I Locate 4 hole plugs in the small bag supplied

the holes in washer back panel.

4 BOLTS

Leveling your washer

Excessive noise and vibration can be prevented by properly leveling the washer.

1 For free standing installation and with the washer

within 4 feet (1 m) of its final location, place a level on top of the washer.

2 Use adjustable pliers to adjust the leveling legs so

the washer is level front-to-rear and side-to-side, and stable corner-to-corner.

3 Press down on alternate corners and sides and feel

for the slightest movement. Adjust the appropriate leg(s) so the washer sits solidly on the floor on ALL four legs. Keep the leveling leg extension at a minimum for best performance of the washer.

For pedestal installations, see additional installation instructions included with the pedestal.

Connecting inlet water

1 Run some water from the hot and cold faucets

to flush the water lines and remove particles that might clog the water valve screens and to

determine which faucet is hot and which is cold supply.

RUBBER WASHERS MUST BE PRESENT

Hoses are not included with washer purchase, See "Accessories" section for various inlet hose kits to fit

your specific installation,

2 Connect the HOT inlet hose to the HOT inlet

connection on the washer and the COLD inlet hose to the COLD inlet connection on the washer.

Tighten by hand until snug. Then tighten each supply connection another 2/3 turn with pliers.

Do not cross thread or over-tighten these connections,

3 Connect the HOT inlet hose to the HOT water

supply and the COLD inlet hose to the COLD water supply. Tighten by hand until snug. Then tighten

each supply connection another 2/3 turn with pliers. Do not bend, kink or pinch water inlet

hoses.

4 Turn on the water and check for leaks.

USE ONLY

NEW HOSES

COLD _, ///

HOT

Connecting drain and electrical

1 Locate the anti-siphon ring shipped with your

washer. Place it over the end of the drain hose and slide it past the first ring of "accordion" ribs.

2 Form a "U" shape on the end of the drain hose

with the hose pointed toward the drain. Place the formed end in a laundry tub or a standpipe and secure the drain hose with the cable tie (provided

in the enclosure package) to the standpipe, inlet hose, laundry tub, etc. so the hose does not pull

out from the force of the water.

The standpipe inside diameter must be 1-1/4" (3.2 cm) minimum. There must be an air gap around the drain hose in the standpipe. A snug hose fit can cause a siphoning action.

)Check to ensure the power is off at a circuit breaker/

fuse box before plugging the power cord into an outlet.

3 Plugthe power cord into a grounded outlet.

Groundir

i i _

P......dwith

3-pronggroundedplug

ION

01SC

$LID'_ DISC

TO HERE

4 Turn on the power at a circuit breaker/fuse box. 5 Carefully slide the washer to its final position.

Recheck for level and rock corners for stability. Remove and discard door tape.

6 Read the Use & Care Guide provided with the

washer. It contains valuable and helpful information that will save you time and money.

7 Runthe washer through a complete cycle, checking

for water leaks and proper operation.

8 If you have any questions during initial operation,

please review the "Service Prevention Checklist" in

your Use & Care Guide before calling for service.

9 Placethese instructions in a location near the

washer for future reference.

))A wiring diagram and technical data sheet are located

under the washer top panel, on top of the detergent dispenser housing.

)!!i!i!l!_!0 ;ii

HATCHING STORAGE PEDESTAL*

Classic White Pedestal - P/N CFPWD15W C{assic Sitver Pedestal - P/N CFPWD15A

A storage pedesta{ accessory, specifically designed for this washer may be used to e{evate the washer for ease of use. This pedesta{ wi{{ add about i5" (38 cm) to the height of your unit for a total height of 51.25" (!30 cm).

_Other colors may be available. Contact the sourcewhere you purchasedyour washer,

DRYER STACKING KIT

P/N STACKIT4X

Depending on the model you purchased, a kit for stacking a matching dryer on top of this washer may have been

included in the initial purchase of your dryer. If your model did not include a stacking kit or you desire another stacking kit, you may order one.

INLET HOSE KITS Pleasecall 866-233-8353 (in Canada, 800-265-8352)

to explore hose kit options that will meet your specific installation needs.

DRAIN HOSE EXTENSION KIT

P/N 137098000

In order to reach standpipe heights or distances beyond the reach of the drain hose supplied, order the DRAIN

HOSE EXTENSION KIT.

HOBILE HOHE INSTALLATION KIT

P/N137067200

Installation in a mobile home requires the use of a MOBILE HOME INSTALLATION KIT.

UNIVERSAL APPLIANCE WRENCH

P/N137019200

A UNIVERSAL APPLIANCE WRENCHis available to aid in dryer/washer/pedestal feet adjustment.

TOUCH UP PAINT PENS*

ClassicWhite Touch Up Pen - P/N 5304468812

Classic Silver Touch Up Pen - P/N 5304471228

_Other colors may be available. Contact the sourcewhere you purchasedyour washer,

Failure to use accessories manufactured by (or approved by) the manufacturer could result in personal injury,

Replacement parts:

If replacements parts are needed for your washer, contact the source where you purchased your washer or refer to your Use and Care Guide for more information.

Label all wires prior to disconnection when servicing controls. Wiring errors cancause improper and dangerous

operation. Verify proper operation after servicing.

+ 25 hidden pages