Frigidaire FAA053P7A1, FAA053P7A2, FAA053P7A3, FAA053P7A4, FAA055P7A1 Installation Guide
...
u m
READ BEFORE iNSTALLING UNIT
MS niWindow Mounting
Your ah"conditioner is desigl_ed to install in skmdard
double lumg windows with opening widths ol 22 to 36
inches (559 mm to 914 ram) (FIG. l)
Lower sash must open suificiemly to allow a clear vertical
opening of 14-1/2 inches (368 ram). Side louvers and the
rear of the AC must have clear air space to allow
enough airllow through the condensel; hn" heat removal.
The rear of the unit must be outdoors, not inside a
building or garage°
When handling unit, be careful to avoid cuts
f?om sharp metal edges and aluminum fins on
front and rear coils.
Beibre installing unit, the top rail must be
assembled on the unit.
_lbp Rail Hardware Qty.
3/8" Screw 4
Top Rail 1
NOTE: SAVE CARTON and these INSTALLA-
TiON iNSTRUCTiONS fin: fmnre reference. The caJlon is
the best way to store unit during wimer, or when not h_use.
Some assemNy is required. Please read these instructions
Mounting Hardware
Qty.
3/4 'screws
lock frame
sash lock
7
TOOL NEEDED:
* PhilBips Screwdriver
A. Remove the air
conditioner flTomthe
cmlon and place on a
flat surface.
B. Remove top rail from
tlle bottom of the
packaging material as
shown in Fig. A
C. Align the hole in the
the top of the unit as
shown in Fig. B
D. Secure the top raiI to
rite unit with the 3/8"
Screws as shown in
Fig. (7
Packagitlg .
Fig. A
Top Rail
TOOLS NEEDED:
• Drill (if pik)t hales are needed)
NOTE: FOR SAFETY REASONS, ALL
FOUR (4) SCREWS MUST BE SECURELY
FASTENED.
How to Install
NOTE: Top Rail and Sliding Panels at each side are
o_gset to provide the proper pitch to the rear of (5/16").
This is necessary for proper condensed water utilization
and drainage. If you are not using the Side Panels for
any reason, this pitch to the rear must be maintained!
Place unit on floor, a bench or a table, There is a
Left and Right Window Filler Panel - be sure to
use the proper panel _i_reach side,When installed
the []ange [or securhlg the panel hi place to the window sill
will be [)acing into the morn,
A. Hold file
Accordion
Pane] in one
hand and
geJlt]y pull
back the
center to }]ee
the open end.
See Figure 2.
C, Once the panel
has been
hlstaHed on the
side of the
cabinet, make
sure it sits
file [rame
making Might
adjustments. SHde the top and bottom ends of the [tame
into the top and bottom rails of file cabinet. Figure 5.
B, Slide the fl:ee end (I"section) of the panel hlto the
cabinet as shown in Figures 3A, 3B & 4_ SHde the
panel down. Be sure to leave el_ough space to sJip the
top and bottom of the fl'ame into the mils on the cabinet.
D. Slide the panel aH the way hi and repeat on the oilier
side.
NOTE" If storm window blocks AC, see FIG, 12,
Keep a firm grip on the air conditioner, carefully
place file unit into the window opening so the
bottom of the ai r conditioner }rame is against the
window sill (FIG.
6). Carefully close
the window behind
the top rail of the
unit,
ExteJld the side pands out against the window
h:arne(FIG, 7),
Loading...