FRIGIDAIRE Electric Patio Grill User Manual

Grill Assembly Built-In Instructions

5-12

13-15

21-22

16-19

Welcome & Congratulations

Please record Grill information for future reference and service work:

Model #:

Serial #:

Date of Purchase:

Gas Type:

Please retain this manual for future reference

Congratulations on your purchase of a new gas grill! At Electrolux Home Products, we are very proud of our product and are completely committed to providing you with the best service possible. Your satisfaction is our number one priority.

We know you’ll enjoy your new gas grill and Thank You for choosing our product. We hope you consider us for future purchases.

PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS

This Use & Care Manual provides specific operating instruction for your model. Use your gas grill only as instructed in this manual. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.

Questions? 1-800-320-0859

TESTED IN ACCORDANCE WITH ANSI Z21.58b-2002/CGA 1.6b-M02 STANDARD FOR OUTDOOR COOKING GAS APPLIANCES. THIS GRILL IS FOR OUTDOOR USE ONLY.

Check your local building codes for the proper method of installation. In the absence of local codes, this unit should be installed in accordance with the National Fuel Gas Code No. Z223.1-2002 and the National Electrical Code ANSI/NFPA No. 70-1990

WARNING

DO NOT try lighting this appliance without reading

the “LIGHTING INSTRUCTIONS” section of this manual.

FOR YOUR SAFETY

DO NOT store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

An LP cylinder not connected for use shall not be stored

the vicinity of this or any other appliance.

General Safety Instructions

IMPORTANT SAFETY INFORMATION

Read this manual carefully before using your grill to reduce the risk of fire, burn hazard or

other injury.

- Extreme care should be used because of the high temperatures produced by this appliance. CHILDREN SHOULD NOT BE LEFT UNATTENDED IN AN AREA WHERE THE GRILL IS BEING OPERATED.

- This appliance must be kept clear from combustible materials, gasoline or other flammable vapors and liquids. Do not allow flammable materials to come in contact with grate, burner or hot surfaces.

- Do not repair or replace any part of this appliance unless it is specifically recommended in this manual. A qualified service technician should conduct all other service.

- Follow the installation and servicing instructions provided with this product. Have your grill installed by a qualified service technician. Locate the main gas supply valve so that you know how to shut the gas off to your grill. If you smell gas, make sure all gas connections are tight before operation. If you continue to smell gas call a qualified technician.

- When lighting a burner, always pay close attention to what you are doing. Be certain you are pushing the ignitor that lights the burner you intend on using.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flames.

3. Open lid.

4. If odor continues, immediately call your gas supplier.

FOR OUTDOOR USE ONLY

This appliance is not intended to be

installed in or on recreational vehicles or boats.

CALIFORNIA PROPOSITION 65 - WARN- ING: The Burning of gas cooking fuels generates some by products which are on the list of substances which are known by the State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of potential exposure to such substances. To minimize exposure to these substances, always operate this unit according to the use and care manual, ensuring you provide good ventila-

tion when cooking with gas.

Grill Features: FD30

1. Roll top grill hood 8. Warming shelf

2. Grilling/Cooking surface 9. Infrared back burner

3. Side Shelf 10. Electronic ignitor: main, rear infrared

& side burner

4. Control knob: back infrared burner 11. Cart w/doorr

5. Control knobs: main burners 12. Ignitor access opening

6. Convection vents 13. Side Burner

7. Handle 14. Control knob: Side Burner

Cart Parts

2 L-shaped side pieces 1 U-shaped back side piece 1 Base 2 Wheel channels

Car

t Door Parts

1 Door handle kit 1 Nylon bushing 1 Door pivot screw and nut

Grill Par

1 Stainless steel grill head 1 Stainless steel side shelf 1 Side burner (side shelf) 1 Electronic ignitor 5 Flavor grids 3 Stainless steel bar grates 1 Stainless steel warming rack 1 Drip pan 1 Magnetic catch 1 Hose and regulator (LP models only)

Assembly Par

14 Hex head screws 8 Bolts 1 Rubber Door Stop with Bolt 11 1/4” Plastic Plug

Par

t #’s

WIP-192-71D384 WIP-192-72D384 WIP-192-70D304 WIP-192-438365L/R

RMP-122-00921 RMP-122-00520 RMP-122-00598/122-00508

Grill Par

WIP-122-11D304 WIP-192-326393 WIP-191-43DGN4 RMP-122-53306 WIP-191-13D384 RMP-122-00699 WIP-191-538015 RMP-122-00005 RMP-122-00029 RMP-122-00821

Assembly Par

RMP-122-00615 RMP-122-00626 RMP-122-00579 RMP-122-00492

Grill Components List

Cart Assembly, Door Stops & Door Pivot Bolts

1. Attach the two L-shaped sides to the back portion of the cart, making sure the two holes face up & the key holes are on the top, using the (4) self tapping hex head screws. (See Fig. 1)

Note: A power screwdriver is required to install the

screws-be cautious not to over-tighten and strip the screws.

2. Set the base on the top of the cart assembly, with large opening closer to back portion of cart, and align the eight mounting holes. Then set the 2 wheel channels on the base and attach them using the (8) bolts provided, from inside the cart upwards through wheel channels. (See Fig. 2)

Note: Tighten the bolts securely

3. Door Stop: Insert Door Stop Bolt downward from bottom side of Cart Base through the hole found in the right/front of the base. (See Fig 3)

4. Screw Rubber Cap onto Bolt from the topside of Cart Base and tighten securely. (See Fig 4)

4. Door Pivot Bolt: Insert Bolt downward from

bottom side of Cart Base through the hole found in the left/front of the base and secure with bolt. (See Fig. 2)

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Note: Prior to assembly remove protective film from stainless steel parts

Screws

Assembly requires: 4 tools and a Friend

Tools required:

Power screwdriver Screwdriver extension 1/4” socket wrench 1/2” socket wrench adjustable wrench scissors

Caution: Gas regulator is not flush with bottom. DO NOT let the Grill head sit flat without placing support around regulator to prevent damage to the regulator prior to installing on cart.

Bolt up through bottom of cart base

LP Tank cutout

Door Pivot Bolt Hole

Door Stop Hole

Wheel Channel

Grill Assembly

Attaching Grill Head to Cart

1. While keeping the Grill on the foam base lean it onto its back. (be sure to hold the hood shut when doing this.) With the Grill on its back, loosen all 4 bolts on the bottom side of the Grill, but do not remove.(See Fig. 5)

2. Using 2 self tapping hex head screws, attach the magnetic door catch in the 2 holes in the bottom of the grill. (See Fig. 6)

3. Have someone help you pick up the grill and set it on the top of the cart, with the front of the grill above the door opening. Make sure the 4 bolt heads fall through the large opening of the key hole slots in the top of the cart. Slide the grill head backward, so the bolts are resting in the small opening of the key hole slots. Tighten the bolts securely.

Be sure not to over tighten and strip the bolts. Next insert 4 hex head screws into grill

bottom through cart. (See Fig. 7)

Note: This is a very heavy step that requires

two individuals to complete.

Installing the Car

t Door

1. While holding the door line up the bottom hole on the door with the bolt sticking up through base of cart. Next place a nylon bushing onto the top pin, then depress the pin and insert into the hole in the bottom of the grill. (See Fig. 8)

Fig. 7

Fig. 8

Nylon Bushing

Door Pivot Bolt

Fig. 6

Screws

Catches face towards front of grill

Screw holes

Bolts

Fig. 5

Screw hole for magnetic catch

Grill Assembly

Installing the Cart Door Handles

1. Using a 5/32” allen wrench insert 1 screw through the inside of the door front into a bar handle end and tighten securely. (See Fig. 9)

2. Insert Bar Handle into the End Cap attached to the door and then into the other End Cap and tighten End Cap with allen wrench and screw. (See Fig. 10)

3. Complete Door. (See. Fig. 11)

Installing the Drip

Tray

1. The drip pan is installed inside of the cart under the grill head.

2. Slide the drip pan onto the two ledges located on the bottom of the grill, by inserting it from the front of the cart. (See Fig. 12)

Screw Holes

End Cap

Backside of door: 2 screw locations

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Bar Handle

Grill Assembly

Front of

Grill

Slide onto rails under grill

+ 16 hidden pages