Frigidaire DGMV174KFA, FGMV174KFA Installation Guide

|HSTALLA'| |OH INsrRucrleNs

BEFORE YOU BEGIN

• _ Save these instructions for local

inspector's use.

• _ Observe all governing codes and coordinates.

• NOTE TO iNSTALLER - Be sure to leave these

instructions with the Consumer. NOTE TO CONSUMER - Keep these instructions for

future reference. SKILL LEVEL - Installation of this appliance requires

basic mechanical and electrical skills.

Read these instructions completely and carefully.

1 MOUHTJNGSPACE

This Microwave Oven/Hood requires a mounting space on

a wall as shown in Figure 1. It is designed to be used with standard 12" wall cabinets.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

• Please read all instructions thoroughly before installing the Over the Range Microwave Oven. Two people are recommended to install this product.

If a new electrical outlet is required, its installation should be completed by a qualified electrician before the Microwave

Oven is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.

2 WALLCONSTRUCTION

This Microwave Oven/Hood should be mounted against and supported by a flat vertical wall. The wall must be flat for

proper installation. If the wall is not flat, use spacers to fill in the gaps. Wall construction should be a minimum of 2"x 4" wood studding and 3/8"or more thick dry wall or plaster/lath. The mounting surfaces must be capable of supporting weight

of 110 pounds--the oven and contents--AND the weight of all items which would normally be stored in the top cabinet

above the unit.

Backsplash At least 2"

cooking

snrface

66" ormore

from floor

The unit should be attached to a minimum of one 2" × 4" wail stud or two 2" x 3" wail studs.

To find the location of the studs, one of the following methods may be used:

A. Use a stud finder, a magnetic device which locates the

nails in the stud.

B. Use a hammer to tap lightly across the mounting surface

to find a solid sound. This will indicate stud location.

The center of the stud can be located by probing the wall with a small nail to find the edges of the stud and then placing a

mark halfway between the edges. The center of any adjacent studs will normally be 16" or 24" to either side of this mark.

HEEDHELP?

For customers in the United States and Canada United States: 1-800-944-9044 Canada: 1-800-265-8352

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

316495062

TINSEB221WRRZ-ELg1

PrintedinThailand

3 ELECTRICALGROUHDIHGiNSTRUCTiONS 4 HOODEXHAUSTDUCT

This appliance must be grounded. This oven is equipped with

a cord having a grounding wire with a grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and

local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing

an escape wire for the electric current.

WARNING - Improper use of the grounding plug can result in a risk of electric shock.

ELECTRICALREQUiREIVIEHTS

The oven is equipped with a 3-prong grounding plug. DO

NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE

THE GROUNDING PIN FROM THE PLUG.

DO NOT USE AN EXTENSION CORD.

The Power Supply Cord and plug must be connected to

a separate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit, single grounded receptacle. The receptacle should

be located inside the cabinet directly above the Microwave Oven mounting location as shown in Figure 2.

HOTE:

1. If you have any questions about the grounding or electrical instructions, consult a qualified electrician or serviceperson.

2. Neither Electrolux nor the dealer can accept any liability for damage to the oven or personal injury resulting from failure

to observe the correct electrical connection procedures.

When the hood is vented to the outside, a hood exhaust duct is required. All ductwork must be metal; absolutely do not use

plastic duct. Check that all connections are made securely. Please read the following carefully:

EXHAUSTCONNECTION:The hood exhaust has been designed to connect to a standard 3 1/4" x 10" rectangular duct. If

round duct is required, a rectangular-to-round adapter must be used.

REAR EXHAUST: If a rear or horizontal exhaust is to be used, care should be taken to align the exhaust with the space between the studs, or wall should be prepared at the time it is constructed by leaving enough space between wall studs

to accommodate exhaust.

MAXIMUM DUCTLENGTH:For satisfactory air movement, the total duct length of 3 1/4"x 10" rectangular or 6" diameter round duct should not exceed 140 feet.

Elbows, adapters, wall caps, roof caps, etc. present additional resistance to air flow and are equivalent to a section of straight

duct which is longer than their actual physical size. When calculating the total length, add the equivalent lengths of all transitions and adapters plus the length of all straight duct sections. Figure 3 shows the approximate feet of equivalent

length of some typical ductwork parts. Use the values in parentheses for calculating air flow resistance equivalent,

which should total less than 140 feet.

90° Elbow(10ft.)

90° Elbow(25ft.)

45° Elbow(5ft.)

Adaptor (5 ft.)

Wallcap (40ft.)

Figure3

ld' WideElbow(10ft.)

Roof cap (24 ft.)

5 7 PREPARATIONOFTHEOVENTOOLSRECOMMENDEDFOR

iNSTALLATiON

• Phillips Screwdriver

• Electric Drill

® 1/2", 6/8" and 3/32" Drill Bits

• 1 1/2"Wood Bit or Metal Hole Cutter (if metal cabinet is used)

• Saw to cut exhaust opening (if needed)

• Protective Drop Cloth for product and range -

you may also use carton for protection

• Scissors

• Pencil

• Measure

• Tape

6 INSTALLATIONHARDWARE

Open the bottom of the carton, bend the carton flaps back and tilt the oven over to rest on plastic foam pad.

Lift carton off oven and remove all packing materials, Installation Instructions, Wall Template, Top Template, Charcoal Filter, Turntable andTurntable Support; however,

DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the ceiling in the oven cavity. SAVE THE

CARTON AS IT MAY MAKE INSTALLATION EASIER.

2. CHECKTHE OVEN. Check the oven for any damage, such as misaligned or

bent door, damaged door seals and sealing surfaces, broken or loose door hinges and latches and dents inside

the cavity or on the door. If there is any damage, do not operate the oven and contact your dealer or Electrolux

AUTHORIZED SERVICER.

The INSTALLATION HARDWARE (itemsO-(Z)) packed with the oven should contain the following:

Item Name Quantity

Q Wood Screw 5 x 35 mm 6 ® Toggle Bolt 3/16" 4

@ Top Cabinet Screw 5 x 85 mm 2 @ Flat Washer 30 mm diameter 2

® Grommet 1 ® Tapping Screw 4 x 8 mm 4

@ Exhaust Damper Assembly 1 @ Grease Filter 2

d; L2;.

r................. _7i i P_ate

i ft ii ii

.... ,/IVlonnting

'45

Figure5

\ .................................................................................../

Partsshownnotto commonscale.

Figure4

8 VENTiLATiONSYSTEM

(PREPARiHG 8VEH FOR IHSTALLATIOH)

This microwave oven/hood is designed for adaptation to three types of hood ventilation systems. Select the type required

for your installation.

RECIRCULATING-- non-vented, ductless. Follow installation procedure (A). Recirculating requires

the use of the Charcoal Filter, which has already been

installed in the oven. HORIZONTALEXHAUST-- outside ventilation.

Follow installation procedure (B). VERTICALEXHAUST-- outside ventilation.

Follow installation procedure (C).

BECIBCULATING: NON-VENTED,DUCTLESSOPERATION

(A)

The unit is shipped assembled for recirculating.

The Exhaust Damper Assembly is not required for

recirculating exhaust.

Charcoal Filter, which was installed in your microwave oven, is used for nonvented, recirculated installation. The

Charcoal Filter should be replaced every 6to 12 months,

depending on use. Remove three Hood Louver screws. Tilt the Hood louver downward then pull it out so bottom tabs become unlocked. Pull the Charcoal Filter upward to remove from your oven. Attach the Charcoal Filter to the upper side of the oven by sliding into the tabs. See

Figure 6-1,6-2.

Oven light

Charcoal filter

(B)HOBIZONTALEXHAUST:OUTSIDEVENTILATION

1. Remove and save 2 screws from back edge and 1screw from the top center of Fan Cover Bracket. Remove Fan Cover Bracket by sliding it inthe opposite direction of the arrow on the Fan Cover Bracket, as shown in Figure 7.

2. Withdraw Hood Fan Unit carefully and slip wires out of Wire Box. See Figure 8.

CAUTION:Donot pull orstretchhoodfanwiring.

3. Rotate the Hood Fan Unit and turn end-over-end so that the fan blade openings are facing the back of the oven.

Replace Hood Fan Unit into the oven. Be careful not to pinch the lead wire between the inner bracket and the Hood Fan Unit. See Figure 9.

4. Put the lead wire into Wire Box. See Figure 10.

5. Replace the Fan Cover Bracket by sliding it into the slits in the same direction as the arrow on the Fan Cover

Bracket. Make sure the fan blades are visible through the rear openings in the oven before proceeding. Attach Fan Cover Bracket to unit with 3 screws, which were removed in Step 1 above. See Figure 11. The Hood Fan Unit is now rotated for horizontal exhaust operation.

6. Attach the Exhaust Damper Assembly to the back of the unit. See Figure 10.Use two Tapping Screws 4x 8 mm from the INSTALLATION HARDWARE and tighten into place.

Fan Cover Bracket

Tabs

Bottom tab

Tabs

Backer /

Oven

/ \\

Figure7

FanCoverBracket

Rotate90° _/

Figure 11

90VEH IHSTALLATiOH

TappingScrew

Figure 10

VEHTiLATJOHSYSTEM

(PREPARINGOVENFORiNSTALLATiON)

VERTICALEXHAUST:OUTSIDEVENTiLATiON

(c)

Remove and save 2 screws from back edge and 1 screw

from the top center of the Fan Cover Bracket. Remove

Fan Cover Bracket by sliding it in the opposite direction of the arrow on the Fan Cover Bracket as shown in Figure

2. Withdraw Hood Fan Unit carefully and slip wires out of Wire Box. See Figure 8. CAUTION: Do not pull or stretch hood fan wiring.

3. Turn the Hood Fan Unit end-over-end. Rotate the Hood Fan Unit 90° so that the fan blade openings are facing

upward. Replace Hood Fan Unit into the oven. Be careful not to pinch the lead wire between the inner bracket and

the Hood Fan Unit. See Figure 11.

4. Put the lead wire into Wire Box. See Figure 11.

5. Replace the Fan Cover Bracket by sliding it into the slits in the same direction as the arrow on the Fan Cover

Bracket. Make sure the fan blades are visible through

the top openings in the oven before proceeding. Attach the Fan Cover Bracket to unit with 3 screws, which were

removed in Step 1 above. See Figure lO.The Hood Fan Unit is now rotated for vertical exhaust operation.

6. Attach the Exhaust Damper Assembly to the fan cover bracket on the top of the outercase cabinet after mounting

the oven. To attach the Exhaust Damper Assembly, refer

to MOUNTING OVEN TO THE WALL, page 6 Figure 17.

THISOVENCANNOTBEPROPERLYINSTALLEDWITHOUTREFERRING TOTHEMOUNTINGINSTRUCTIONSFOUNDONBOTHTEMPLATES.

THENEXTSTEPISTOREADANDFOLLOWMOUNTINGINFORMATION ONBOTHTOPCABINETANDWALLTEMPLATES.

NOTE:THISOVENSHOULDBEATTACHEDTOATLEASTONEWALL STUD.

MOUNTINGPLATE

1. Separate 4 Toggle Bolts, packed in the INSTALLATION HARDWARE, from the Toggle Nuts.

2. _ Use the mounting template

provided to Use wood screws to attach mounting plate to the stud or studs. UseToggie Bolts to attach mounting plate through the holes UNLESS THOSE

HOLES ARE LOCATED ON THE STUD. Insert one Toggle Bolt where appropriate (these correspond

to holes of the Wail Template) and put the

Toggle Nuts onto the Toggle Bolts. Figure 13. Refer to instructions in

Wall Template.

3. Position the Mounting Plate with the Toggle Bolts attached at the wall location and insert Toggle Nuts

and Bolts through the holes in the wall with the Toggle Nuts closed. Figure 15. Use Wood Screws to attach the Mounting Plate to studs.

NOTE:Before insertion, be sure you leave a space more than the thickness of the wall between the Mounting Plate

and the end of each of the Toggle Nuts (in the closed position). If you do not leave enough space, the Toggle Nut will not be able to open on the other side of the wall. Also, once a Toggle Nut opens, it cannot be withdrawn

from the hole; therefore make sure all of the Toggles are in the correct position before insertion.

4. Align the Mounting Plate carefully and hold in position while tightening Toggle Bolts. Pull Toggle Bolt toward you and turn clockwise to tighten. Figure 14.

9 OVENiNSTALLATiONooot.

Toggle Bolt

Mounting Plate J

Figure 12

Figure15

MOUNTINGOVENTOTHEWALL

Two people are recommended to attach the Microwave Oven/

Hood to the Mounting Plate.

1. Thread the power supply cord through the hole made in the bottom of the top cabinet.

2. Install the oven by tilting it forward and sliding it onto the tabs of the Mounting Plate. Rotate the oven up so it rests

against the wall. See Figure 15.

3. Use the two Top Cabinet Screws and two Flat Washers,

supplied in the INSTALLATION HARDWARE, to attach

the unit to the top cabinet. See Figure 16.

4. Secure the bottom of the oven to the Mounting Plate

by using two Tapping Screws 4 x 8 mm from the INSTALLATION HARDWARE. See Figure 16.

TappingScrew

Figure16

TappingScrew

./j jj

Figure17

CHECKLISTFORiNSTALLATiON

1. Make sure the unit has been installed according to all of the Installation Instructions and the Wall and Top Cabinet Templates.

2. Plug in the power cord.

3. Keep the Operation Manual.

+ 14 hidden pages