Frigidaire CPLMB209DCB, CPLMB209DCC, GLMB209DBA, GLMB209DBB, GLMB209DBC Installation Guide

Installation

Built-in Trim Kit

Instructions

BEFORE YOU BEGIN

• IMPORTANT- Save these instructions

for local inspector's use,

• IMPORTANT- Observe all governing

codes and coordinates,

• Note to Installer- Be sure to leave these

instructions with the Consumer,

• Note to Consumer- Keepthese

instructions for future reference.

• Skill level - Installation of this appliance requires
basic mechanical and electrical skills,

FOR YOUR SAFETY:

WARNING - Before beginning the installation,

switch power off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally, When the service disconnect-
ing means cannot be locked, securely fasten a promi-
nent warning device, such as a tag, to the service
panel,

QUESTIONS?

For customers in the United States call: 1-800-944-9044
For customers in Canada call: 1-800-213-9397 (English)

1-800-668-4606 ext.8199 (French)

Visit our Website at: www.frigidaire.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

MWTRMKT27 and MWTRMKT30

Read

these instructions completely and carefully.

Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not
covered under the Warranty,

• Unplug the microwave oven before attempting

installation of this kit,

• Because the kit includes metal parts, caution

should be used in handling and installation to
avoid the possibility of injury.

• Do not remove permanently affixed labels, warn-

ings, or plates from the product. This may void

the warranty,

IMPORTANT- PLEASE READ

AND FOLLOW

THIS BUILT-IN KIT IS DESIGNED FOR USE ONLY
WITH ELETROLUX MICROWAVE OVENS SPECI-
FYING BUILT-IN KIT

MWTRMKT27 OR MWTRMKT30 ON THE RATING
LABEL ON THE LEFT SIDE WALL OF THE
MICROWAVE OVEN CAVITY.

IF YOUR LOWER CONVENTIONAL OVEN IS NOT
LISTED IN THE USE AND CARE MANUAL OF THE
MICROWAVE OVEN, THEN DO NOT INSTALL THE
MICROWAVE OVEN ABOVE IT OR IN ANY AREA
WHERE HEAT AND STEAM ARE GENERATED; FOR
EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL
RANGE.

1 P/N316137335

TINSEB384MRRO

Installation Instructions

PARTS INCLUDED IN THE KIT

1. Front Frame Assembly - QTY 1

2. Exhaust Duct Assembly - QTY 1

3. Screw A - QTY 2

4. Screw B - QTY 4

CABINET OR WALL CUTOUT

Cutout Dimensions

Height (A)

Minimum 16 3/4"(42.5 cm)
Maximum 17" (43.2 cm)

Width (g)

Minimum 24 3/8"(61.9 cm)
Maximum 24 11/16"(62.7 cm)

Depth (C)

Minimum 20" (50.8 cm)

FrontFrameAssembly

ScrewA

ScrewB

ELECTRICAL OUTLET LOCATION

Outlet should NOT be in the shaded area as indicated on

Illustration 1

NOTE 1:

If the Depth (C) dimension is greater than 21" (53,3 cm),

the outlet location may be in any area on the rear wall.
NOTE 2:

The floor of the opening should be constructed of ply-
wood strong enough to support the weight of the oven
and floor load (approximately 100 pounds). The floor

should be level for proper operation of the oven, Be sure
to check the local building code as it may require that the
opening be enclosed with side, ceiling and rear partition,
The proper functioning of the oven does not require the

enclosure,

ExhaustDuctAssembly

I 6" _--

(15.2crn)

Illustration 1

2