Frigidaire CPLEFM99ECH, CPLEFM99ECK, CPLEFM99ECJ, CPLEFM99ECG, CPLEFM99ECD Owner’s Manual

...

...... 5

trois ......... 7-12

g........................... 13

Control Pad Features ................... 14

Setting Oven Controls ............ 15-29

Bake-n-Warm TM Double Oven 29-31

Self Cleaning ........................... 32-34

Adjusting Oven Temperature ....... 35

General Care & Cleaning ....... 35-38

Questions? 1-800-944-9044 (UnitedStates)

1-800-668-4606 (Canada)

Visit the Frigidaire Web Site at:

http://www.frigidaire.com

READ AND SAVE THESE INSTRUCTIONS p/n 316423404 revA (0512)

Before You Call

Solutions to Common Problems ................ 39-40

Warranty ......................... Back Page

We Icom e & Congra tula tions

..... ,, _ o .

Serial plate location

Open Bake-n-Warm TM Double Oven or Warmer Drawer.

Congratulations on your purchase of a new range! At Electrolux Home Products, we are very proud of our product and are completely committed to providing you with the best service possible. Your satisfaction is our number one priority.

We know you'll enjoy your new range and Thank You for choosing our product. We hope you consider us for future purchases.

PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS This Use & Care Manual provides specific operating instructions for your model.

Use your range only as instructed in this manual. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.

Please record your model and serial numbers below for future reference.

Model Number: Serial Number:

Purchase Date:

This Use & Care Manual contains general operating instructions for your range and feature information for several models. Your range may not have all the described features. The graphics shown are representational. The graphics on your range may not look exactly like those shown.

Product Registration

The self-addressed PRODUCT REGISTRATION CARD should befilled in completely, signed and returned to Electrolux Home Products.

Read all instructions before using this appliance. Save these instructions for futu re reference.

This manual contains mportant safety symbols and instructions. Please pay attention to these symbols and follow all instructions given.

This symbol will help alert you to situations that may cause serious bodily harm. death or property damage.

This symbol will help alert you to situations that may cause bodily injury or property damage.

Important Safety Instructions

• Remove all tape and packaging before using the range.

Destroy the carton and plastic bags after unpacking the range. Never allow children to play with packaging material.

• Proper Installation--Be sure your appliance is properly installed and grounded by a qualified technician in accordance with the National Electrical Code ANSI/

NFPA No. 70 latest edition and local electrical code requirements. Install only perinstallation instructions provided in the literature package for this range.

Ask your dealer to recommend a qualified technician and an authorized repair service. Know how todisconnect the power

to the range at the circuit breaker or fuse box in case of an

emergency.

• User servicing--Do not repair or replace any part of the appliance unless specifically recommended in the

manuals. All other servicing should be done only by a qualified technician. This may reduce the risk of personal

injury and damage to the range.

• Never modify or alter the construction of a range by removing leveling legs, panels, wire covers, anti-tip

brackets/screws, or any other part of the product.

• All ranges can tip.

• Injury to persons could result.

• Install anti-tip device packed with range.

• See Installation Instructions.

tipping, the rangemust be secured by

properly installed anti-tip bracket provided

_To reduce the risk of

with the range. To check if the bracket is

installed properly, visually check that rear

secured by the anti-tip bracket by removin¢

lower panel or storage drawer. For models

with a Warmer Drawer or Bake-n-Warm TM

leveling leg is inserted into and fully Double Oven, grasp the top rear edge of

the range and carefully attempt to tilt it forward. Refer to the installation

instructions for proper anti-tip bracket

Stepping, leaning or sitting on the doors or

drawers of this range can result in serious injuries and also cause damage to the range. Do not allow children to

climb or play around the range. The weight of a child on an open door may cause the range to tip, resulting in serious burns or other injury.

Do not store items of interest to children in

the cabinets above a range or on the backguard of a range. Children climbing on the range to reach items could be seriously injured.

Do not use the oven or Warmer Drawer/

Bake-n-Warm TM Double Oven (if equipped) for storage.

Never Use Your Appliance for Warming or

Heating the Room.

• Storage in or on Appliance--Flammable materials

should not be stored in an oven, Warmer Drawer/Bake- n-Warm TM Double Oven, near surface units or in the storage drawer. This includes paper, plastic and cloth

items, such as cookbooks, plasticware and towels, aswell as

flammable liquids. Do not store explosives, such as aerosol

cans, on or near the range.

• Do Not Leave Children Alone--Children should not be left alone or unattended in the area where appliance is

in use. They should never be allowed to sit or stand on any part of the appliance.

• DO NOTTOUCH SURFACE UNITS, AREAS NEAR THESE UNITS, HEATING ELEMENTS ORINTERIORSURFACES OFTHE OVENS. ALL surface units and oven heating elements may be hot even though they are dark in color. Areas near surface units may become hot enough to cause burns. During and after use, do not touch, or let clothing or otherflammable materials touch these areas until they have had sufficient time to cool. Among these areas are the cook top, surfaces facing the cook top, the oven vent openings and surfaces near these openings, oven door and window.

•Wear Proper Apparel--Loose-fitting or hanging garments should never be worn while using the appliance. Do not let clothing or otherflammable materials contact hot surfaces.

• Do Not Use Water or Flour on Grease Fires--Smother

the fire with a pan lid, or use baking soda, a dry

chemical or foam-type extinguisher.

•When heating fat or grease, watch it closely. Fat or grease may catch fire if allowed to become too hot.

• Use Only Dry Potholders - Moist or damp potholders on hot surfaces may result in burns from steam. Do not let potholders touch hot heating elements. Do not use a towel or other bulky cloth instead ofa potholder.

• Do Not Heat Unopened Food Containers - Buildup of pressure may cause container to burst and result in injury.

• Remove the oven door from any unused range if it is to be stored or discarded.

IMPORTANT--Do not attempt to operate the range during a power failure. Ifthe power fails, always turn off the range. If the range is not turned offand the power resumes, the range

will begin to operate again. Once the power resumes, reset the

clock and oven function.

IMPORTANT INSTRUCTIONS FOR USINGYOUR COOKTOP

• Know which knob controls each surface heating unit. Place a pan of food on the unit before turning it on, and turn the unit off before removing the pan.

• Use Proper Pan Size--This appliance is equipped with one or more surface units of different sizes. Select utensils having flat bottoms large enough to cover the surface unit heating element. The use of undersized utensils will expose a portion of the heating element to direct contact and may result in ignition of

clothing. Proper relationship of utensil to element will also improve efficiency.

• Utensil Handles Should Be Turned Inward and Not Extend Over Adjacent Surface Elements--To reduce the risk of burns, ignition

of flammable materials, and spillage due to unintentional contact with the utensil, the handle of the utensil should be positioned so that it is turned inward, and does not extend over adjacent surface

units.

• Never Leave Surface Elements Unattended at High Heat Settings--Boilovers cause smoking and greasy spillovers that

may ignite, or a pan that has boiled dry may melt.

• Do Not Immerse or Soak Removable Heating Elements-- Heating elements should never be immersed in water. Heating elements clean themselves during normal operation.

• Glazed Cooking Utensils--Only certain types of glass, glass/ ceramic, ceramic, earthenware, or other glazed utensils are

suitable for cook top service without breaking due to the sudden change in temperature. Check the manufacturer's recommendations for cook top use.

• When flaming foods under a ventilating hood, turn the fan on.

IMPORTANT INSTRUCTIONS FOR USINGYOUR OVEN

• Use Care When Opening Oven Door or Warmer Drawer/Bake- n-Warm TMDouble Oven (if equipped)--Stand to the side of the

range when opening the door of a hot oven. Let hot air or steam escape before you remove or replace food in the oven.

• Keep Oven Vent Ducts Unobstructed. The oven vent is located under the left rear surface element if your model is equipped with coil elements. The oven vent is located below the backguard for models equipped with ceramic-glass cook tops. Touching the

surfaces in this area when the oven is operating may cause severe burns. Also, do not place plastic or heat-sensitive items on or near the oven vent. These items could melt or ignite.

• Placement of Oven Racks. Always place oven racks in desired location while oven is cool. If rack must be moved while oven is

hot use extreme caution. Use potholders and grasp the rack with both hands to reposition. Do not let potholders contact the hot heating elements in the oven. Remove all utensils from the rack before moving.

• Do not use the broiler pan without its insert. The broiler pan and its insert allow dripping fat to drain and be kept away from the high

heat of the broiler.

• Do not cover the broiler insert with aluminum foil. Exposed fat and grease could ignite.

• Protective Liners--Do not use aluminum foil to line the oven bottom. Only use aluminum foil as recommended in this manual.

Improper installation of these liners may result in risk of electric shock, or fire.

SELF CLEANING OVENS

• Clean in the self-cleaning cycle only the parts listed in this Use & Care Manual. Before self cleaning the oven, remove the broiler pan and any utensils or foods from the oven.

• Do Not Use Oven Cleaners--No commercial oven cleaner or oven liner protective coating of any kind should be used in or around any part of the oven.

• Do Not Clean Door Gasket--The door gasket is essential for a good seal. Care should be taken not to rub, damage or move the gasket.

•The health of some birds is extremely sensitive to the fumes given off during the self-cleaning cycle of any range. Move birds to another well-ventilated room.

IMPORTANT INSTRUCTIONS FOR CLEANING YOUR RANGE

• Clean the range regularly to keep all parts free of grease that could catch fire. Pay particular attention to the area underneath each surface element. Do not allow grease to accumulate.

• Kitchen cleaners and aerosols--Always follow the manufacturer's recommended directions for use. Be aware that excess residue from cleaners and aerosols may ignite causing damage and injury.

• Clean Ventilating Hoods Frequently--Grease should not be allowed to accumulate on the hood or filter. Follow manufacturer's instructions for cleaning.

FOR CERAMIC-GLASS COOK TOP MODELS

• Do Not Cook on Broken Cook Top--If cook top should break, cleaning solutions and spillovers may penetrate the broken cook top and create a risk of electric shock. Contact a qualified technician immediately.

• Clean Cook Top with Caution--if a wet sponge or cloth is used to wipe spills on a hot cooking area, be careful to avoid a steam burn. Some cleaners can produce noxious fumes if applied to a hot surface.

Important Safety Notice

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list ofsubstances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances.

Your Electric Range Features Include:

1. Electronic Oven Control with Kitchen Timer.

2. Left Front & Bridge Element Control & Digital Display (some

models) or Dual Element Control (some models).

3. Left Rear Single Element Control & Digital Display or Dual

Element Control (some models).

4. Bake-n-Warm TM Double Oven Control.

5. Bake-n-Warm TM Double Oven Indicator Light.

6. Warming Zone Element Control (some models).

7. Warming Zone Indicator Light (some models).

8. Warming Zone HOT SURFACE Indicator Light (some models).

9. Right Rear Single Element Control & Digital Display or Dual

Element Control (some models).

10. Right Front Dual Element Control & Digital Display.

11. Oven Interior Light with removable Cover.

12. Automatic Oven Door Light Switch (some models).

13. Self-Cleaning Oven interior.

14. Self-Clean Door Latch.

15. Convection Fan & Cover.

16. Adjustable Interior Oven Rack(s).

17. Large 1 piece Oven Door Handle (styles & colors vary).

18. Full width Oven Door with Window (styles & colors vary).

19. Bake-n-Warm TM Double Oven, Drawer Rack, Drawer Handle, Interior Light (some models) & Window (some models).

20. Easy to clean upswept Cooktop.

21. Ceramic Smoothtop (elements, styles & color will vary).

22. Left Front Single (some models) or Dual Element (some models).

23. Bridge Element (some models).

24. Left Rear Single (some models) or Dual Element (some models).

25. Warming Zone Element (some models).

26. Right Rear Single (some models) or Dual Element (some models).

27. Right Front Dual Element.

28. Broil Pan (some models).

29. Broil Pan Insert (some models).

30. Roasting Rack (some models).

31. Leveling Legs and Anti-tip Bracket (included).

NOTE: The features of your range may vary according to model type & color.

OVEN VENT

Oven Vent Location

The oven vent is located under the left side of the control panel

(See Fig. 1). When the oven is on, warm air passes through the vent.

This venting is necessary for proper air circulation inthe oven and good

baking results. DO NOT BLOCK OVEN VENT.

Removing & Replacing Oven Racks

To remove, pull the rack forward until it stops. Lift up front of rack and slide out. To replace, fit the rack onto the guides on the oven walls. Tilt the front of the rack upward and slide the rack back into place.

Arranging Oven Racks & Roasting Shelf

ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS COOL (PRIOR TO OPERA TING THE 0 VEN). Always use oven mitts when

using the oven.

Recommended Rack Positions for Broiling, Baking & Roasting: Food Rack Position

Broiling hamburgers & steaks 1 Broiling meats, chicken or fish 1, 2, or 3 Cookies, cakes, pies, biscuits 3 or4

& Muffins

Frozen pies, angel food cake, 6 yeast, bread, casseroles, small cuts of meat or poultry Turkey, roast or ham (use Roasting Shelf) 7 (some models)

Roasting Shelf

positioned incorrectly

Fig .3

Fig. 2

Types of Oven Racks & Roasting Shelf

Correct Roasting

Shelf position

Fig. 4

Your range may be equipped with one or more of the oven rack types shown; Flat Oven Rack

(Fig. 5) and Roasting Shelf (Fig. 6; some models). To maximize cooking space the Roasting Shelf should be used in the lowest rack position to roast large cuts of meat and poultry (See Fig. 2).

Flat Oven Rack

Fig. 5

Roasting Shelf

Fig. 6

Place Roasting Shelf with care in rack position 7 (See Fig. 2). Be sure the Roasting Shelf is level and the front end of the

shelf rests over the front ends of the oven rack glides on both sides of the oven interior (See Figs. 3 & 4).

Baking Layer Cakes with 1 or 2 Oven Racks

For best results when baking cakes using 2 oven racks, place cookware on rack positions 3 & 6 (See Fig. 7). For best results when using a single Flat Oven Rack, place cookware on rack position 4 (See Fig. 8).

Air Circulation in the Oven

For best air circulation and baking results allow 2-4" (5-10 cm) around the cookware for proper air circulation and be sure pans and

cookware do not touch each other, the oven door, sides or back of the

oven cavity. The hot air must be able to circulate around the pans and

cookware inthe oven for even heat to reach around the food.

Fig. 7 Fig. 8

Cooktopradiantareasthatheat

Modelswith a Bridge Element Models with 4 Dual Elements

Fig. 1

o om!o

_leme_

_i OFF hi OFF hi OFF hl hi OFF hl

Lell OO Left OO _}o_) _ieht Right....,_o ,_0,_o .... 8°$.o,.

Left Front Left Rear Right Rear Right Front

About the Ceramic Glass Cooktop

The ceramic cooktop has radiant surface elements located below the surface of the glass. The design of the ceramic cooktop outlines the

area of the surface element underneath. Make sure the diameter of the pan matches the

diameter of the element outline on the cooktop (See Fig 1). Heat is transferred up through the surface of the cooktop to the cookware. Only flat-bottom cookware should be used. The type and size of cookware, the number ofsurface elements in use and the settings, are all factors that will affect the amount of heat that will spread to areas beyond the surface elements. The areas surrounding the elements may become hot enough to cause burns.

About the Radiant Surface Elements

The element temperature rises gradually and evenly. As the temperature rises, the element will glow red. To maintain the selected setting, the element will cycle on and off. The heating element retains enough heat to provide a uniform and consistent heat during the off cycle. For efficient cooking, turn off the element several minutes before cooking is complete. This will allow residual heat to complete the cooking process.

Fig. 2 (Bridge Element on some models)

NOTE: Radiant elements have a limiter that allows the element to cycle ON and OFF, even at the HI setting. This helps to prevent damage to the ceramic cooktop. Cycling at the HI setting is normal and can occur

if the cookware is too small for the radiant element or if the cookware bottom is not flat (Refer to page 13 for using correct cookware

instructions with the cooktop).

Your range is equipped with radiant surface burners with different wattage ratings. The ability to heat food quicker and in larger volumes increases as the element wattage increases.

NOTE: Please read detailed instructions for

ceramic glass cooktop cleaning in the Care & Cleaning section and Before You Call

checklist sections of this Use and Care Manual.

Settin g Surfa ce Controls

The Electronic Surface Element Control (ESEC)

The Electronic Surface Element Control ("ESEC")feature

includes 4 digital display windows. The ESEC feature provides a numeric digital setting for4 of the radiant surface element positions on the cooktop. These settings work the same way as normal knob setting indicators work except the settings are displayed in digital windows (Figs. 1thru 4).

The available ESEC Display Settings

The ESEC control provides various heat levels from Hi (Fig. 2) to Lo (Fig. 4) and OFF (Fig. 1).

Use the chart (Fig. 5) to determine the correct setting for the kind of food you are preparing. The Simmer settings are used Ri_,2_t

tosimmerandkeeplargerquantitiesoffoodswarmsuchas _:,: @Rai stews and soups. The lower Simmer settings are ideal for

delicate foods and melting chocolate or butter. Fig. 1

Note: The size and type of cookware used will influence the setting needed for best cooking results.

OFF

Fig. 2

Radiant surface elements may appear to have _F, ff_, _ "\,\ cooled after they have been turned off. The glass surface may '_4 still be hot and burns may occur if the glass surface is o

touched before it has cooled sufficiently

?i/7

peppers a rs,spoon o ersorpla wrappingson

_ DO not pJace pJastic items such as saJtandhke h Jd st ic %% ._,,_'-- _\

top of the range when it is in use. These items could melt ...._ ..... "

or ignite. Potholders, towels or wooden spoons could catch fire if placed too close to the surface elements.

(DQ@ /d_ht

,,Jtd@

Fig. 3 Fig. 4

Recommended Surface Cooking Settings

RECOMMENDED SETTINGS FOR SINGLE, BRIDGE & DUAL ELEMENTS

Setting Type of Cooking

HIGH (8- Hi) MEDIUM HIGH (5- 8) MEDIUM (3- 5)

Start most foods, bring water to a boil, pan broiling Continue a rapid boil, fry, deep fat fry Maintain a slow boil, thicken sauces and gravies, steam

vegetables

OFF

MEDIUM LOW (2 - 3) Keep foods cooking, poach, stew LOW (Lo - 2) Keep warm, melt, simmer Fig. 5

Setting Surface Contro Is

ESEC Hot Element Indicator Message (HE)

After using any of the single, dual or Bridge radiant element positions the cooktop will become very hot. Even after turning the control knob to OFF, the cooktop will remain hot for some time. The ESEC control monitors the temperature of the cooktop and displays the 0FII t message "HE" (hot element) warning when the cooktop is still too hot to touch (See Fig.1 ). If the HE message appears in the window, the control can still be turned on again for use.

ESEC Error Indicator Message (Er)

An error message will be displayed (flashing "Er") at power up (or after a power failure) if ANY of the surface control knobs were left inthe ON positions. If a power failure should occur, be sure to set all of the 4 surface control knobs to the OFF position (See Fig. 2). This will reset _°

the surface controls. Be sure to reset the clock (See page 15). Once the surface controls have been set to the

OFF positions and the clock has been set with the correct time of day, the surface controls should return to normal operation, tf the surface controls do not function and the "Er" _ I1_*__ message remains in any display after following these procedures, contact an authorized

servicer for assistance.

ESEC Lockout Feature ( - - )

The Self-Clean feature will notoperate whenever a radiant surface element isON. Conversely

the ESEC feature will not operate during the Self-Clean cycle. Whenever the ESEC Lockout feature is active," --" may appear in any display window (See Fig. 3). If any of the surface

elements are still hot during active Lockout, "HE" will appear in the window instead of the "- -"

message.

The Single Radiant Elements (some models)

Fig. 1

Fig. 2

Some models have single radiant surface elements at 2 locations; the right rear (Fig. 5) and left rear (Fig. 6) element positions. The BRIDGE (some models) element position can also be used as a single element (See Bridge Element Operating Instructions on pages 10-11 ).

To Operate the Single Elements (some models):

1. Place correctly sized cookware on the radiant surface element.

2. Push in and turn the surface control knob in either direction to the desired setting using the ESEC digital display

window for the desired setting (Fig. 4). Turn (do not push) the knob to adjust the setting if desired. Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking. Each surface element provides a constant amount of heat at each setting. A glowing red surface heating area extending beyond the bottom edge of

the cookware indicates the cookware is too small for the surface heating area.

3. When cooking has completed, turn the surface control knob to OFF before removing the cookware. Note: The HE message will appear after turning the control knob to OFF if the cooktop is still hot and will remain on until the heating surface area has cooled sufficiently.

Note: See page 8, Fig. 5 for recommended control settings.

Fig, 3

Radiant surface elements may appear to have cooled after they have been turned off. The glass surface may still be hot and burns may occur if the glass surface is touched before it has cooled sufficiently.

Setting Surface Controls

hi ti

Fig. 1 Fig. 4

Ii 0 FI:: I_i hi 0 FF I_i

Fig. 2 Fig. 5

{a_le Element

The Dual Radiant Elements (all models)

The cooktop is equipped with one or more dual radiant surface elements. Symbols on the control panel (See Fig. 4) are used

to indicate which coil of the dual radiant element will heat. The symbol shown in Fig. 1indicates that only the inner coil will

heat. The symbol shown in Fig. 4 indicates that both inner and outer coils will heat. You may switch from either coil setting at any time during cooking.

To Operate the Dual Element(s):

1. Place correctly sized cookware on the dual surface

element.

2. Push in and turn the control knob counterclockwise (See Fig. 2) for smaller cookware or clockwise (See Fig. 5) for

largercookware.

3. Use the ESEC digital display window for the desired

setting. Turn (do not push) the knob to adjust the setting if

needed. Start most cooking operations on a higher setting

and then turn to a lower setting to finish cooking. Each surface element provides aconstant amount of heat at each setting. A glowing red surface heating area extending

beyond the bottom edge of the cookware indicates the cookware is too small for the surface heating area.

4. When cooking has completed, turn the surface control knob to OFF before removing the cookware. Note: The HE message will appear after turning the control knob to OFF if the cooktop is still hot and will remain on until the radiant heating surface area has cooled sufficiently. Note: See page 8, Fig. 5 for recommended control settings.

Fig. 3 Fig. 6

The Bridge Radiant Element (some models)

Some ceramic cooktops are equipped with a "BRIDGE" surface element located at the left front and middle (See Fig. 10) positions. The Bridge can be used when cooking with rectangular (like a griddle) or oval shaped cookware (Fig. 10). The element will maintain an even temperature setting across both portions of the Bridge. If needed for normal cookware, the Bridge element can work like a single element without the Bridge (See Fig. 8).

Bridge element operation symbols are located on the control panel on each side of the Bridge element control knob. These symbols indicate the direction to turn the control knob when operating the Bridge element. The symbol in Fig. 7 indicates that only the single portion of the Bridge element will heat (See Fig. 8). The symbol in Fig. 9 indicates that both the single and Bridge portions of the element will heat together (Fig. 10). You may switch from either of these settings at any time during cooking with the Bridge element.

Radiant surface elements may appear to have

cooled after they have been turned off. The glass surface may still be hot and burns may occur if the glass surface is touched before it has cooled sufficiently.

Fig. 7 Fig. 9

Ebm_t t

O 0

_a 0 FIF hi

Fig. 1

Fig. 2

[

OI'::n::

Fig. 3

Fig. 4

I_-dge I I(!me//t

To Operate the Bridge Element (some models):

1. Place correctly sized cookware on the Bridge surface element.

2. Push in and turn the control knob counterclockwise (See Figs. 1 & 2) to heat the portion of the Bridge element for normal shaped cookware or clockwise (See Figs. 3 & 4) for larger or rectangular shaped cookware.

3. Use the ESEC digital display window for the desired

setting. Turn (do not push) the knob to adjust the setting if

needed. Start most cooking operations on a higher setting

and then turn to a lower setting to finish cooking. Each surface element provides a constant amount of heat at each setting. A glowing red surface heating area extending

beyond the bottom edge of the cookware indicates the

cookware is too small. Please note that not all cookware will fit the Bridge element correctly.

4. When cooking has completed, turn the surface control knob to OFF before removing the cookware. The HE message will appear in the display after turning the control knob to OFF if the cooktop is still hot and will remain on until the radiant heating surface area has cooled

sufficiently. Note: See page 8, Fig. 5 for recommended

control settings.

The BRIDGE element may also be used in combination with the left rear single element. Because these elements have 2 different controls, one element can be used to cook while the other element may be used to keep food warm (See Fig. 5).

Radiant surface elements may appear to have

cooled after they have been turned off. The glass surface may

Fig. 5

still be hot and burns may occur if the glass surface is touched before it has cooled sufficiently.

Operating the Warming Zone (some models)

The purpose of the Warming Zone is to keep hot cooked foods at serving temperature. Use the Warming Zone to keep cooked foods hot such as; vegetables, gravies, casseroles, soups, stews, breads, pastries and oven-safe dinner plates. Always start with hot food. It is not recommended to heat cold food on the Warming Zone.

All food placed on the Warming Zone should be covered with a lid or aluminum foil to

maintain quality. For best results, when warming pastries or breads, the cover should have an opening to allow moisture to escape. Do not use plastic wrap to cover food. Plastic may melt onto the surface and be very difficult to clean. Use only plates, utensils and cookware recommended for oven and cooktop use on the Warming Zone.

Always use pot holders or oven mitts when removing food from the Warming

Zone as cookware and plates will be hot.

To Set the Warming Zone Control (some models):

1. To set the control, push in and turn the knob. The On indicator light will come on (See Figs. 1 and 2). The temperatures are approximate, and are designated by HI, MED and LO. However, the control can be set at any position between HIand LO for different levels

m_d

of heating (Fig.1).

2. When done, turn the control to OFF. The Warming Zone Hot surface indicator light will remain on until the Warming Zone cools to a moderate level (See Figs. 1 & 2).

Fig. 1

Temperature Selection

Refer to the table for recommended Warming Zone food settings (Fig. 3). lfa particular food is not listed, start with the medium level, and adjust as needed. Most foods can be kept at serving temperatures by using the medium level.

The Warming Zone will not glow red when it is hot, but becomes hot enough to

cause burns. Avoid placing hands on or near the Warming Zone until the Warming Zone Hot surface indicator light is off.

Warming Warming Zone Warming

Zone Hot Surface Zone

Indicator Light Indicator Light Control

Warming Zone

Warming Zone Recommended Food

Settings Table

Food Item Heating

Level

Hot Beverages HI Fried Foods HI

Vegetables MED

Soups (Cream) MED Stews MED

Sauces MED Meats MED Gravies LO

Eggs LO Dinner Plates with Food LO

Casseroles LO Breads/Pasteries LO

Fig. 2 (some models)

Fig. 3

Using proper cookware

The size and type of cookware used will influence the setting needed for best cooking results. Cookware

*CORRECT

_:!iii!i:!ii!:i;i!i_i!i_iiii_i!i_i_ii!:!ii:_i!¸ ;_!i_i_i_i!i_ii:ii!_

INCORRECT

should have fiat bottoms that make good contact with the entire surface heating element (See Fig. 2). Check for flatness by rotating a ruler across the bottom of the cookware (See Fig. 1).

Be sure to follow the recommendationsfor

using proper

cookwa re as illustrated.

For more information about the ceramic

cooktop see "Cooktop Cleaning &

Maintenance" in the General Care &

Cleaning section.

Fig. 1 Fig. 2

t t

• Flat bottom and straight sides.

• Tight fitting lids.

• Weight of handle does not tilt pan. Pan is well

balanced.

• Pan sizes match the amount of food to be

prepared and the size of

the surface element.

• Made of a material that conducts heat well.

• Easy to clean.

• Always match pot diameter to element surface

diameter.

• Curved and warped pan bottoms.

• Pan overhangs element by more than one-half inch.

}

• Pan is smaller than

element.

• Heavy handle tilts pan.

Cookware Material Types

The cookware material determines how evenly and quickly heat is transferred from the surface element tothe pan bottom. The most popular materials available are:

ALUMINUM - Excellent heat conductor. Some types of food will cause it to darken (Anodized aluminum cookware resists

staining & pitting), tf aluminum pans slide across the ceramic cooktop, they may leave metal marks which will resemble scratches. Remove these marks immediately.

COPPER - Excellent heat conductor but discolors easily. May leave metal marks on ceramic glass (see Aluminum above).

STAINLESS STEEL - Slow heat conductor with uneven cooking results. Is durable, easy to clean and resists staining.

CAST IRON -A poor heat conductor however will retain heat very well. Cooks evenly once cooking temperature isreached. Not recommended for use on ceramic cooktops.

PORCELAIN-ENAMEL on METAL - Heating characteristics will vary depending on base material. Porcelain-enamel coating must be smooth to avoid scratching ceramic cooktops.

GLASS - Slow heat conductor. Not recommended for ceramic cooktop surfaces because it may scratch the glass.

+ 29 hidden pages