Frigidaire CPA12EDU111, CPA12EDU110, CPA123DU110, CPA093DU111, CPA093DU110 Owner’s Manual

F GIDAIRE

= i_ ii

Normal

Accessories Included

www,frigi

This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as
instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that

may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.

Power supply cord

with 3-prong grounding

plug and current

detection device

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. Read product labels for flammability and other warnings.

For Your Safety

Prevent Accidents

• Be sure the electrical service is adequate for the model you have chosen. This information

can be found on the serial plate, which is located on the side of the cabinet.

o If the air conditioner is to be installed in a window, you will probably want to clean both

sides of the glass first.

• Be sure the air conditioner has been securely and correctly installed according to the
installation instructions in this manual. Save this manual for possible future use in

removing or reinstalling this unit.

Electrical Information

The complete electrical rating of your new protable air conditioner is stated on the serial

ii ii

plate. Refer to the rating when checking the electrical requirements.

ii

Be sure the air conditioner is properly grounded. To minimize shock and fire hazards,

ii'

proper grounding is important. The power cord is equipped with a three-prong grounding
plug for protection against shock hazards.

ii,

Your air conditioner must be used in a properly grounded wall receptacle. If the wall
receptacle you intend to use is not adequately grounded or protected by a time delay fuse

ii

or circuit breaker, have a qualified electrician install the proper receptacle.

ii =

Do not run air conditioner without outside protective cover in place. This could result in
mechanical damage within the air conditioner.

DANGER.I Avoid Serious Injury or Death

This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.
Do not insert or place fingers or objects into the air discharge area on top of the unit.

Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.
Do not cut or damage the power cord.
If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.

In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized
Electrolux servicer.

• Do not operate the air conditioner with wet hands.

• Do not pull on the power cord.
Do not drink any water that is drained from the air conditioner.

02009 Electrolux Home Products, Inc. All rights reserved.

CAUTION. I Avoid Injury or damage to the unit or other property

o

Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make
units run excessively.

o

Do not climb on or place objects on the unit.
Do not hang objects off the unit.

Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.

Periodically check the condition of the unit's installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.

Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.

Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.

READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.

Unit must be upright for one hour prior to operating.

Operation of Current
Device

Plug in &
press RESET

The power supply cord contains a current device that senses damage to the power cord. To test

your power supply cord do the following:

1. Plug in the Air Conditioner.

2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESETbutton pops out.

3. Press the RESETbutton, Again you will notice a click as the button engages,

4. The power supply cord is now supplying electricity to the unit,

. Do not use this device to turn the unit on or off.

Always make sure the RESETbutton is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.

' If power supply cord is damaged, it CANNOT be repaired, It MUST be replaced by one obtained

from the product manufacturer.

02009 Electrolux Home Products, Inc. All rights reserved.

Product Registration Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the side of the cabinet.

Model No.

Serial No.

Register Your Product

The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,

signed and returned to the Frigidaire Company.

Normal Sounds

Sound of l?ushing Air

At the front of the unit, you may

hear the sound of rushing air
being moved by the fan.

High pitched Chatter
Today's high efficiency

compressors may have a
high pitched chatter during

the cooling cycle.

Gurgle/Hiss

"Gurgling or hissing" noise may be

heard due to refrigerant passing

through condenser during normal

operation.

Vibration

Unit may vibrate and make noise
because of uneven floor.

02009 Electrolux Home Products, Inc. All rights reserved.

Unit Description

CONTROL PANEL

CARRYING HANDLE

(BOTH SIDES)

REMOTE CONTROL !
STORAGE DOOR

REMOTE CONTROL

Accessories Included

PARTS: PARTS NAHE: QUANTITY:

ROOM AIR DISCHARGE

Fig. 1

Adaptor A(Unit) 2 pcs

EXHAUST

AIR OUTLET

ADAPTOR A

AIR INTAKE

DEHUMIDIFYING
DRAIN OUTLET

DUCTED AIR INLET

BOTTOM TRAY DRAIN OUTLET

_J % J J

Window Hose Kit(Hose and Adaptor B) 2 set

Window Sliding Kit 1 set

Foam Seal 3 pcs

Remote Control 1 pc

Battery(For remote control) 2 pcs

12.7mm Screw 4 pcs

19mm Screw 2 pcs

12.7mm Hex Head Cap Screw 2 pcs

Safety pc

Lock

1

Fig, 2

• Check all the accessories are included in the package and please refer to the installation
instructions for their usage.

02009 Electrolux Home Products, Inc. All rights reserved.

r-

Installation Instructions

HOSES INSTALLATION

In the COOLING Mode the appliance must be placed close to a window or

opening so that the air outside could be ducted inside the unit and the warm
exhaust air can be ducted outside.

First position unit on a flat floor and make sure there's a minimum of 30.5cm

clearance around the unit, and is within the vicinity of a single circuit outlet

power source.

1. Take out the hoses from the package.

2. Remove adaptor A from unit by sliding sideways (Fig. 3).

3. Extend the other end(without adaptor) of the hoses (Fig. 4) and screw
it to adaptor A (Fig. 5).

4. Slide the hose assemblies onto the unit (Fig. 6).

5. Affix the adaptor B into the window slider kit and seal. (Fig. 7&8)

Vertical
window

_" Extend the end of hose

Fig, 4

Window Slider Kit
Minimum :67.5cm(26.6")

Maxmum: 123cm(48.5")

Fig. 7

window

Horizontal l

Window Slider Kit
Minimum:67.5cm(26.6")

Maxmum: 123cm(48.5")

The hose can be extended from its original length of 38.1cm up to

139.7cm, but it is the best to keep the length to minimum required. Also
make sure that the hose does not have any sharp bends or sags. (Fig. 9)

ii

Fig, 8

ide

Fig, 5

////

y//,

////

//,'1

z///

////

////

////

y//,,

7//,

////

y//

Fig. 9

02009 Electrolux Home Products, Inc. All rights reserved.

Installation Instructions

(continued)

Installation in a double-hung sash window

1. Cut the foam seals(adhesive type) to the proper lengths and attach them
to the window and stool. (Fig. 10)

2. Open the window sash and place the window slider kit on the window stool

(Fig. 11). Attach the window slider kit to the window stool. Adjust the length
of the window slider kit according to the width of window. Screw down the
two screws on the window slider kit. SeeFig.11. Cut the adjustable window
slider kit if the width of window is less than 67.5cm (Fig. 12).

3. Close the window sash securely against the window slider kit. (Fig. 13)

4. Drive two 12.7 mm screws to secure the window slider kit to the window
sash. (FIG. 13)

5. Securethe window slider kit to the window stool (FIG. 13):
A: Forwooden windows: Use 19mm screws for securing.

B: ForVinyl-Clad windows: Use 12.7mm hex head cap screws for securing.

6. To secure lower sash in place, attach right angle sash lock with

12.7mm (1/2") screw as shown (FIG. 14).

NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad

windows, so you can use lock by window itself.

7. Cut the foam seal to an appropriate length and seal the open gap

between the top window sash and outer window sash, as shown in Fig.15.

::____a°dhesev:t t_Pe)

Fig. 10

in_dowsliderkit

Windowstool

Cut this side to fit your window

Fig. 11

!2.7mm screws

dowsliderkit

Fig. 14
Fig, 15

1 Y--

hex head cap screws .... \ . p.._

Windowstool rig, 13

Installation in a sliding sash window

1. Cut the foam seals(adhesive type) to the proper lengths and attach them

to the window frame. SeeFig.16.

2. Open the window sash and place the window slider kit on the window stool.

See Fig.17. Attach the window slider kit to the window stool. Adjust the

length of the window slider kit according to the height of window. Screw
down the two screws on the window slider kit. SeeFig.17. Cut the adjustable
window slider kit if the height of window is less than 67.5cm (Fig. 12).

3. Close the sliding sashsecurely against the window slider kit. (Fig. 18)

4. Drive two 12.7mm screws to secure the window slider kit to the window sash.
(Fig. 18)

5. Drive two 19mm screws to secure the window slider kit to the window stool.
(Fig. 18)

6. Cut the foam seal to an appropriate length and seal the open gap

between the sliding sashand outer window sash, as shown in Fig.19.

7.To secure the sliding sashin place, attach right angle sash lock with 12.7mm

(1/2") screw as shown.(Fig.20)

...................... : ........................ -- ................................ : ! ;=J

Foamseal

(adhesive type) _.

Window stool

6Z5cm_!23cm]_

Window stool Window slider kit

Window slider kit

Fig, 12

Fig. 16

Fig. 17

19mm screws':,. screws

Foamseal

Fig, 19

02009 Electrolux Home Products,Inc.

All rights reserved.

ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!Jiii!ii

Fig. 18

Air Conditioner Features

CONTROL PANEL

REMOTE CONTROL

TURNS UNIT ON OR OFF

CHECK FILTER DISPLAYS REMOTESIGNAL

RESETBUTTON TEMPERATURE/TIME RECEIVER

(

= \ auto []

filter / coot m

o]_m mon I heat

timer \_

dry []

fan m u

MODE V A FAN SPEED

temp/timer setting

K'F

moc

m Hr

f f

[-- temp/timer ----J

1

SETS MODE ADJUSTS SETSFAN SPEED

ACTIVATES TIMER

TEMPERATURE

OR TIME

Fig, 21

SWING

BUTTON

swmg

m

s[eep

SLEEP MODE

MODE INDICATION

_auto fSun

\

-- FANSPEEDSELECTION

TEM PERATURE/TIM ER

CONTROL BUTTONS

MODE SELECTOR-

I v I ^ i

_[ .... I........I.......F

FANSPEEDSELECTOR

-- TIMER BUTTONS

SLEEP BUTTON --

RESET+ LOCK

--! .....I ..... I_......it

• _ •

RESET_ L?K

SWING BUTTON
ON/OFF BUTTON

PIN BUTTONS

FRIGIDAIRE

Fig, 22

Battery Size: AAA

Warning: 1. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-

cadmium) batteries.

2. This device complies with Part 15 of the FCCRules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

The RESETbutton isdepressed when you want to return to the initial factory settings. The LOCKbutton isdepressed to
lock the keypad so the settings cannot be changed. The key symbol will appear in the display of the remote control,
depress the LOCKbutton again to release. Usea small pin to depress these buttons.

@2009ElectroluxHome Products, Inc. All rights reserved.

Operating Instructions

The following instructions represent the Control Panel, the same instructions can be used for the Remote Control.

COOLING MODE:

HEATING MODE:
(on some models)

DRY MODE:

AUTO MODE: Always have the hoses attached in this mode,

FAN MODE: In this mode there is no need to use the hoses or drainage hose.

In this mode the adaptor hoses MUST be used.

1. Press the MODE button until the "Cool" indicator lights.

2. Press the " V A" Temp buttons for desired setting.

3. Press the FAN button for desired fan speed.
In this mode you do not need to use the adaptor hoses.

1. Press the NODE button until the "Heat" indicator lights.

2. Press the " V A" Temp buttons for the desired heat setting.

In this mode you do not need to use the adaptor hoses, BUT the water
collected must be discharged. See Drainage Section.

1. Press the NODE button until the "Dry" indicator lights.

2. The fan will run at low speed and the display will show the room temperature.

3. Keep doors &: windows closed for best effect.

When you set the air conditioner in AUTO mode, it will automatically select cooling,
heating(inapplicable for cooling only models), or fan only operation depending on what
temperature you have selected and the room temperature. The air conditioner will
control room temperature automatically round the temperature point set by you. Under
AUTO mode, you can not select the fan speed.

1. Press the NODE button until the "Fan" indicator lights.

2. Press the FAN button to choose the desired fan speed.

3. The fan will run at the selected speed and the display will show the room temperature.

TIMER OPERATION:

SLEEP OPERATION:

@2009ElectroluxHome Products, Inc, All rights reserved. #._

You can set both delay stop and delay start while unit is in ON position or OFF position.
When unit is in ON position, first press TIMER button to go to delay stop setting, then
"timer off" light will illuminate, tap or hold the UP arrow (A) or the DOWN arrow (V) to
change delay stop timer at 0.5 hour increments up to 10 hours, then at 1 hour increments
up to 24 hours. Then press the TIMER button to confirm the setting (the control will confirm
the setting automatically after 5 seconds) and go to delay start setting. Use the same way
as above to set the delay start timing. If you don't need to set delay start, press the
TIMER button again to exit. After 5 seconds, the control will automatically change the
display back to previous temperature display. If you want to check remain timing, press the
TIMER button. The delay start operation automatically selects mode, temperature and
fan speed the same as last operation you set.
When unit is in OFF position, press TIMER button will first go to delay start setting, then
"timer on" light will illuminate, set the delay start and delay stop timing the same way

as above.
To cancel the timer setting, simply tap (A) or (V) button to change the timing to 0.0.

In this mode the selected temperature will increase by 1 °C 30 minutes after the mode
is selected. The temperature will then increase by another 1 °C after an additional 30
minutes. This new temperature will be maintained for 7 hours before it returns to the

originally selected temperature. This ends the "Sleep" mode and the unit will continue to
operate as originally programmed. The "Sleep" mode program can be cancelled at any
time during operation by again pressing the "Sleep" button.

Note: This feature is unavailabe under FAN or DRY modes.

Operating Instructions

(continued)

SWING OPERATION:

CHECK FILTER FEATURE:

FAULT CODE:

temp/timer setting

F

i°C

Hr

temp/timer setting

°F

m°C

Hr

temp/timer setting

If the display reads "EA", the room temperature sensor has failed. Contact your Authorized
Frigidaire Service Center.

If the display reads "ES", the evaporator temperature sensor has failed. Contact your
Authorized Frigidaire Service Center.

If the display reads "E4", the display panel communication has failed. Contact your

m'C

Hr

Authorized Frigidaire Service Center.

When you turn on the unit, the louver will swing and stop at a certain angle. You
can press the SWING button to let the louver swing automatically. Pressthe
SWING button again while you want the louver stop at desired angle.

This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more
efficient operation. The LED (light) which above the "Filter" button will illuminate
after 250 hours of operation. To reset after cleaning the filter, press the "Filter"
button and the light will go off.

temp/timer setting

w'C

Hr

If the display reads "PI", bottom tray is full. Carefully move the unit to a drain location, remove
the bottom drain plug and let the water drain away. Restart the machine until the "PI" symbol
disappears. If error repeats, call for service.

DRAINAGE:

During the dehumidifying mode, you will need a garden hose (sold
separately) to drain the condensate from the unit.

Removethe rubber stopper from the hoseconnector, then screw on a
garden hose to the connector as shown on fig 23.

A. Discharge into a drain that is lower than the unit. /

B. Be connected to a condensate pump (sold separately).

The hose may then: /x_ Girden hose

REMOTE CONTROL STORAGE:

The door on side of the unit is for storing the remote, to open press it as
shown in Fig. 24, to close simply push it back into position.

Removethe
suppliedrubber

)er

Fig, 23

Fig. 24 ]

Presshere

0 @2009 Electrolux Home Products, Inc. All rights reserved,

Operating Instructions

(continued)

HOSES STORAGE:

When the unit is not in use, the hoses could be stored according to the following
steps:

1. Remove the hose assemblies from the unit and the window slider kit.

2. Remove the adaptor A from the hose assemblies.

3. Slide the adaptor A onto the unit.

4. Shorten the hoses to their original size, and put the window hose kits (hose
and adaptor B) onto the hose holders as shown on fig 25.

Fig. 25

ADDITIONAL THINGS
YOU SHOULD KNOW

CARE & CLEANING

..........Filter

\

Now that you have mastered the operating procedure, here are more features in
your control that you should become familiar with.

• The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned
off and on quickly. This prevents overheating of the compressor and possible circuit
breaker tripping. The fan will continue to run during this time.

• The control will maintain the set temperature within 1 °C, between 17 °C and
30 °C (62 °F and 86 °F).

• The control is capable of displaying temperature in degrees Fahrenheit or degrees
Celsius. To convert from one to the other and back, press and hold the "TENP"
Up ( A ) and Down (V) buttons together for 3 seconds.

• There is a 2-Second delay for the compressor shutting down when selecting
FANONLY/HEAT.This is to cover the possibility of having to roll through to select

another mode.

• After a power outage, the unit will memorize the lastsetting and return the unit to
the same setting once power is restored.

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug
the unit before cleaning to prevent shock or fire hazards,

Air Filter Cleaning

• This unit has a filter. Grasp the upper panel tab and take off the filter which behind
the grill of the back panel (Fig.26).

• Wash the filter using liquid dishwashing detergent and warm water. Rinse filter

thoroughly. Gently shake excess water from the filter. Be sure filter is thoroughly
dry before replacing.

• Or, instead of washing you may vacuum the filter clean.

Cabinet Cleaning

Fig. 26

@2009ElectroluxHome Products, Inc. All rights reserved.

• Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet
and front may be dusted with an oil-free cloth or washed with a cloth dampened
in a solution of warm water and mild liquid dishwashing detergent. Rinse
thoroughly and wipe dry.

• Never use harsh cleaners, wax or polish on the cabinet front.

• Be sure to wring excess water from the cloth before wiping around the controls.
Excess water in or around the controls may cause damage to the air conditioner.

Winter Storage

If you plan to store the appliance during the winter, cover it with plastic or return
it to its carton.

1 1

Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not

the result of defective workmanship or materials in this appliance.

OCCURRENCE SOLUTION

Air conditioner will not operate.

Air from unit does not feel cold

enough.

Air conditioner cooling, but room
is too warm - ice forming

on cooling coil behind decorative

front

Wall plug disconnected. Push plug firmly into wall outlet.

Plug Current Device Tripped. Press the RESET button.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Control is OFF. Turn Control ON and set to desired setting.
P1 appears in the display window. Drain water as described in Drainage Section.

Shut off in Heat mode. When the air outlet overheats, the automatic heat protection engages. Remove
any blockages and let appliance cool down. If the heating function can not be restarted after fully

cooling down, the thermal fuse may open the heater circuit, then call for service.

Room Temperature lower than the set temperature (Cool Mode). Reset the temperature.

Room Temperature higher than the set temperature (Heat Mode). Reset the temperature.

Room temperature below 16 °C (60 °F). Cooling may not occur until room temperature rises above
16 °C (60 °F).

Reset to a lower temperature.

Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to
restart when set in the COOL mode.

Outdoor temperature below 16 °C (60 °F). To defrost the coil, set FAN ONLY mode.

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY

mode.

Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then,

set temperature to a higher setting.
Ducts not connected or blocked. See HOSES INSTALLATION Section.

Air conditioner cooling, but room
is too warm - NO ice forming on
cooling coil behind decorative

front,

Air conditioner turns on and off
rapidly.

Noise when unit is cooling.

Room too cold.
Room too hot,

Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.

Temperature is set too high. Set temperature to a lower setting.

Air directional louvers positioned improperly. Position louvers for better air distribution.

Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in
front of unit.

Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.

Unit recently turned on in hot room. Allow additional time to remove "stored heat" from walls, ceiling,
floor and furniture.

Dirty air filter - air restricted. Clean air filter.

Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils
more frequently.

Air movement sound. This is normal. If too loud, set to lower FAN setting.
Vibration from uneven floor. Move or support appliance correctly on even surface.

Set temperature too low. Increase set temperature.

Set temperature too high. Lower setting.

If These Solutions Fail, Call 1-800-265-8352 For Frigidaire Service,

2 02009 Electrolux Home Products, Inc. All rights reserved.

Yourapplianceiscoveredbyalimitedone-yearwarrantyandalimited2-5yearwarrantyonthesealedsystem(thecompressor,

condenser,evaporatorandtubing).Foroneyearfromyouroriginaldateofpurchase,Electroluxwillpayallcostsforrepairingor
replacinganypartsofthisappliancethatprovetobedefectiveinmaterialsorworkmanshipwhensuchapplianceisinstalled,
usedandmaintainedinaccordancewiththeprovidedinstructions.Fromthesecondtothefifthyearfromyouroriginalpurchase
date,ElectroluxwillrepairorreplaceanypartsintheSealedRefrigerationSystem(compressor,condenser,evaporatorandtubing)

thatprovetobedefectiveinmaterialsorworkmanship.Inyears2-5,theconsumerwillberesponsiblefordiagnostic,laborand

partscostsaswellasanyremoval,transportationandreinstallationexpenseswhichareincurredduringserviceoncomponents
otherthanthosecoveredundertheSealedRefrigerationSystem5-yearwarranty.

Exclusions

This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased "as-is" are not covered by this warranty.

5. Food loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.

10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,

handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip

charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,

cabinets, walls, etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than

genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external
causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR

REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST

PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR

CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES

RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME

STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS

OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

IfYou Need

Service

This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North
America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.

Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under

this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described

or illustrated are subject to change without notice.

USA

1.800.944.9044

Electrolux Major Appliances
North America

P.O. Box 212378

Augusta, GA 30907

02009 Electrolux Home Products, Inc. All rights reserved. -t "_

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period

should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone

numbers below.

1.800.265.8352

Electrolux

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

Canada

L5V 3E4

£ D