Frigidaire CFPWD15W Installation Guide
Use these instructions to mount pedestal
under washer and dryer style to the right
with mechanical style timers.
Utilisez ces instructions pour fi xer un socle sous une laveuse et une sécheuse à la
droite munies d’une minuterie mécanique.
Utilice estas instrucciones para instalar
el pedestal por debajo de la lavadora y
secadora de instalación a la derecha con
temporizadores mecánicos.
Washer and dryer consoles with mechanical
style timers.
WHITE KIT COMPONENTS:
D 1 Left Front bracket.
E 1 Right Front bracket.
F 2 Rear brackets.
COMPOSANTS DU NÉCESS. BLANC :
D 1 support avant gauche.
E 1 support avant droit.
F 2 supports arrière.
PIEZAS DEL KIT BLANCO:
D 1 soporte delantero izquierdo.
E 1 soporte delantero derecho.
F 2 soportes traseros.
Tools needed: / Outils nécessaires: / Herramientas necesarias:
OR
OU
O
Optional universal
wrench available
from dealer
Clé universelle
optionnelle (en vente
chez le détaillant)
Llave universal opcional
(disponible a través
de su distribuidor local)
Adjustable wrench
Clé à molette
Llave ajustable
D
E
F
OR
OU
O
9/16” or 14 mm box wrench
Clé polygonale de
9/16 po ou de 14 mm
Llave de cubo de
9/16 po o 14 mm
SCREW KIT COMPONENTS:
COMPOSANTS DU NÉCESSAIRE DE VIS:
PIEZAS DEL KIT (TORNILLOS):
14 #10 (16 x .500) screws.C
14 vis n° 10 (16 x .500).C
14 tornillos n.º 10 (16 x .500).C
AND
ET
Y
La console de la laveuse et la sécheuse est
munie d’une minuterie mécanique.
La consola de la lavadora y la secadora tiene
un temporizador de tipo mecánico.
C
AND
ET
Phillips screwdriver
Tournevis Phillips
Destornillador Phillips
Y
Carpenter’s level
Niveau de charpentier
Nivel de carpintero
WARNING AVERTISSEMENT ADVERTENCIA
Failure to disconnect from power source •
before stacking could result in personal
injury or even death.
Improper installation of dryer venting •
could result in personal injury or damage
to property.
To avoid back or other injury, have more •
than one person move or lift the washer
or dryer.
Do not stack a dryer on top of washer •
already installed on pedestal.
English continued on page 2.
Ne pas débrancher l’appareil de sa source •
d’alimentation en électricité avant de le superposer peut causer des blessures, voire la mort.
Une installation inappropriée du système •
de ventilation de la sécheuse peut causer
des blessures ou des dommages matériels.
Pour éviter les blessures au dos ou •
d’autres types de blessure, demandez
l’aide d’autres personnes pour déplacer
ou soulever la laveuse ou la sécheuse.
Ne superposez pas une sécheuse sur •
une laveuse déjà installée sur un socle.
Pour la suite de la version française,
reportez-vous à la page 5.
1
El no desconectar el suministro eléctrico an-•
tes de la instalación apilada puede ocasionar lesiones personales o incluso la muerte.
La instalación inadecuada de la ventilación •
de la secadora puede ocasionar lesiones
personales o daños a la propiedad.
Para evitar lesiones en la espalda u otro •
tipo de lesiones, procure levantar o mover
la lavadora o secadora con la ayuda de
más de una persona.
No apile la secadora sobre la lavadora si •
ya está instalada sobre un pedestal.
La versión en español continúa en la página 8.
137338900 A (1002)
PREPARATION INSTRUCTIONS
Due to higher center of gravity of appliance on pedestals, some side-to-side rocking is normal during operation.
Vibration can be minimized by assuring appliance is installed
properly, including being level and solid on all four (4) legs by
following these directions.
A) Preparing washer or dryer for mount-
ing on pedestal
If washer or dryer is new and has not been installed yet, skip to 1.
step 4.
If dryer is already installed, disconnect dryer from electrical and 2.
gas connections and exhaust venting.
If washer is already installed, disconnect washer from electrical 3.
connection. Turn off hot and cold water supply and disconnect
hot and cold water supply hoses from water supply outlets.
Disconnect drain hose from drain pipe.
If appliance has plastic feet, screw each foot fl ush to the base.4.
If appliance has metal feet, unscrew them, remove the locking 5.
nut and reinstall the feet fl ush to the base.
Level the pedestal front-to-back and side-to-side by adjusting 2.
each leveling leg. Keep leg extension to a minimum.
Optional universal
wrench (or adjustable
pliers).
lower
raise
If locking nuts are not removed on units with metal
feet, mounting holes in appliance will not align to mounting
holes in brackets.
B) Preparing pedestal before mounting
washer or dryer
Locate pedestal to within a few inches of its fi nal location.1.
DO NOT remove foam!
Allow for approximately 5 in. (12.5 cm) behind the
pedestal for clearance of back of washer or dryer to the wall.
Allow additional space if venting dryer upward or downward.
Rock the pedestal from corner-to-corner to check for stability. 3.
Repeat leveling and rocking until all four (4) feet are sturdy on the
fl oor and pedestal is level.
Without turning the rubber foot, lock each pedestal leg in place 4.
by tightening its lock nut tight against the pedestal base.
lock nut
2
3.1 cu ft WASHER INSTRUCTIONS
C1)
Attaching washer mounting hardware
Use the following instructions for mounting this type of washer 1.
to the pedestal:
Remove 2 screws
from service access
below front panel.
D1) Mounting washer
back or other injury, have more than one person move or lift
the washer.
- EXCESSIVE WEIGHT HAZARD - To avoid
Using two or more persons, slightly tip the washer back and lift it 1.
onto the pedestal. Still tipped, slide the washer back against the
rear brackets and gently set down the front so the appliance is
between the front and rear brackets.
Remove lower service access panel.2.
Remove 2 lower screws from backsheet of washer. Save screws to 3.
reinstall later.
Remove 2 screws from
washer backsheet.
Attach each front clip to outer-most set of holes with 2 screws.4.
Insert “A” tab of each rear bracket into the middle slots on rear 5.
of pedestal. Orient bracket outward for washer mounting.
SLIDE BACK
Adjust the appliance side-to-side to align its mounting holes with 2.
the pedestal’s bracket holes.
Reinstall backsheet screws removed earlier through each rear 3.
bracket into the base of the washer.
Reinstall the lower service access panel.4.
Reinstall the 2 screws removed earlier 5.
each front bracket into the base of the
TIP DOWN
through the outer hole of
washer.
“A”
tab
Install 2 screws through each rear bracket into aligning pedestal 6.
holes.
middle
slot
outward
E
1) Installing or re-installing washer
Slide appliance/pedestal into place.1.
Check for levelness and rock all four (4) legs again. Repeat until 2.
level and solid.
Refer to 3. Washer Installation Instructions for complete details
on installing water, drain, or electrical.
3
5.7 cu ft DRYER INSTRUCTIONS
C2) Attaching dryer mounting hardware D2) Mounting dryer
- EXCESSIVE WEIGHT HAZARD - To avoid
Use the following instructions for mounting this type of dryer to 1.
the pedestal:
back or other injury, have more than one person move or lift
the dryer.
Dryer cabinet with 2
indents on side and 4
inch knockout for side
venting.
Remove all 4 adjustable leveling legs from the appliance base 2.
and save for future use.
Remove 2 plastic hole plugs toward bottom of front panel.3.
Attach each front clip to outer-most set of holes with 2 screws.4.
Using two or more persons, slightly tip the dryer back and lift it 1.
onto the pedestal. Still tipped, slide the dryer back against the
rear brackets so tabs on rear brackets engage the slots on the
back of the dryer. Gently set down the front so the appliance is
between the front and rear brackets.
ENGAGE REAR TABS
SLIDE BACK
Remove 2 plastic hole
plugs toward bottom
of front panel.
Remove 4 plastic leveling legs.
TIP DOWN
Adjust the appliance side-to-side to align its mounting holes with 2.
the pedestal’s bracket holes.
Install a screw through the inner hole of each front bracket into 3.
the base of the dryer.
Insert “B” tab of each rear bracket into the front slots on rear of 5.
pedestal. Orient bracket outward for dryer mounting.
“B”
tab
Install 2 screws through each rear bracket into aligning pedestal 6.
holes.
front
slot
outward
Reinstall the plastic hole plugs in front panel.4.
E2) Installing or re-installing dryer
Slide appliance/pedestal into place.1.
Check for levelness and rock all four (4) legs again. Repeat until 2.
level and solid.
Refer to 3. Dryer Installation Instructions for complete details on
installing electrical, gas, or exhaust venting.
4
Loading...