Frigidaire ATF6000ES0, ATF6000ES1, ATF7000EP0, ATF7000ES0, ATF7000ES1 Installation Guide

Full Size Tumble Action Washers

Before beginning installation, carefully read these instructions. This will simplify the
instaffation and ensure the washer is installed correctly and safely. Leave these instructions

near the washer after installation for future reference.

NOTE: The electrical service to the washer must conform with local codes and ordinances
and the latest edition of the National Electrical Code, ANSI/NFPA 70.

Contents

For your safety the information in

this manual must be followed to minimize the risk

of fire or explosion or to prevent property damage,
personal injury or loss of life.

- Do not store or use gasoline or other flammable
vapors and liquid in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

. Do not try to light any appliance.
. Do not touch any eIectrica[ switch; do not

use any phone in your building.

. Clear the room, building or area of all

occupants.

. immediately call your gas supplier from a

neighbor's phone. Follow the gas suppliers
instructions.

. if you cannot reach your gas supplier, call

the fire department.

SUBJECT PAGE

Preqnstallation Requirements 2

Electrical Requirements 2
Grounding Requirements 2
Water Supply Requirements 2

Drain Requirements 2

Roughqn Dimensions 3

Location Of Your Washer 4

Unpacking 4

Installation 5-6

Replacement Parts 6

installation and service must be performed by a
qualified installer, service agency or the gas
supplier.

Printed in U.S.A.

P/N 134602900A (0512)

PRE-INSTALLATION REQUIREMENTS

Tools Required for Installation:

1. Phillips screwdriver

2. 10 mm socketwith ratchet.

3. Channeldock adjustable pliers.

4. Carpenter's level.

absence of local codes, with tile National Electrical
Codes, ANS!/NFPA 70 (latest edition). If in doubt,

call a licensed electrician. DO NOTcut off or alter
the grounding prong on the power supply cord. In

situations where a two-slot receptacle is present,

it is tile owner's responsibility to have a licensed
electrician replace it with a properly grounded
three prong grounding type receptacle.

ELECTRICAL REQUIREMENTS

CIRCUIT-Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2 wire, with ground, 120 volt, single
phase, 60 Hz, Alternating Current. NOTE: Because of
potential inconsistent voltage capabilities, the useof this
washer with power created by gas powered generators,
solar powered generators, wind powered generators or
any other generator other than the local utility company

is not recommended.

OUTLET RECEPTACLE- Properly grounded 3-prong
receptacle to be located so the power supply cord is

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within

42 inches (!07 cm) of your washer's water inlet. Tile
faucets MUST be 3/4 inch (1.9 cm) garden hose type
so inlet hoses (:anbe connected. Water pressure MUST

be between30 and 120 pounds persquareinch (maximum

unbalance pressure, hot vs. cold, 10 psi.) "four water
department (:anadviseyou of yourwater pressure.Thehot
water temperatureshouldbeabout 140degreesF(60degrees
C).

DRAIN REQUIREMENTS

1. Drain capable of eliminating 17 gals (64.3 L) per
minute.

2. A standpipe diameter of I-I/4 in. (3.18 cm)
minimum.

3. The standpipe height above the floor should be:

Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244cm)

accessible when the washer is in an installed position.

NOTE: GFI(Ground Fault Interrupter) receptacle is not

required.

GROUNDING REQUIREMENTS

Improper connection of the equipment

grounding conductor (:an result in a risk of electrical
shock. Check with a licensed electrician if you are in
doubt asto whether the appliance is properly grounded.

.

Tile washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electrical shock by a path of least

resistance for electrical current.

.

Sinceyour washer is equipped with a power supply
cord having an equipment-grounding conductor
and a grounding plug, tile plug MUSTbe plugged
into an appropriate, copper wired receptacle that
is properly installed and grounded in accordance

with all local codes and ordinances or in tile

o O0

24 in.

(61 cm)

MJn,

BACK

NOTE:

Drain hose attached to the washer can reach a gO
in. (229 cm) high standpipe. For higher standpipe,

use hose P/N 134369410, available from an

authorized parts distributor.

T

96 in.

(244 cm)

Max.

ROUGH-_N D_MENS_ONS

23¾"

(60.33)

24"

(60.96)

/

i

25/8"

(6.67)

22"

(55.88)

255/8"

35/8"

(9.21)

(65.09)

281/4"

inches(¢m}

(71.76)

NOTE: For _edesta{ installations, see additional installation instructions included with the pedestal.

For stackinei installations, see additional installtion instructions included with the stacking kit.
For under counter installations, no special top is required.

27"

1 (68.58)

E6¾"

(21.59) I

:£

!

O

OO

(17115)

I

33½"

(85.09)

inches(cm)

J

BACK

23"

(58.42)

27"

(68.58)

3

LOCATION OF YOUR WASHER

DO NOT INSTALL YOUR WASHER:

1. In an area exposed to dripping water or outside weather 4.
conditions. The ambient temperature should never be below

60 ° F(15.6 ° C) for proper washer (deterg entbreakd°wn) 5.
operation.

2. In an area where it will come in contact with curtains or
drapes. 6.

3. In an area (garage or garage-type building) where gasoline
of other flammables are kept or stored (including
automobiles).

4. On carpet. Floor MUSTbe solid with a maximum slope of
1/2 in. per foot (!.27 cm per 30.5 cm). % ensure vibration 7.

or movement does not occur, reinforcement of the floor

may be necessary.

IMPORTANT

MINIMUM INSTALLATION CLEARANCES

When installed in alcove or closet:

Sides, Rear = 0 in. (0 cm)

Top = 0 in. (0 cm)
When installed in closet: Front = 1 in. (2.54 cm)
Closet door ventilation required: 2 Iouvered openings each 60
in2(387 cm2), 3 in. (7.6 cm)from top and bottom of door.

Carefully return the washer to an upright position.
Carefully move the washer to within 4 feet (122cm) of the

final location.

Remove the following from the back panel of the washer:

4 shipping bolts,
4 spacers,
2 metal "P" clamps.

Remove the 4 plugs from the literature pack located in the
drum and install them in the holesvacated bythe packaging

spacers.

NOTE: If the washer isto be transported at a later date,

tile shipping support hardware must be reinstalled
to prevent shipping damage.

UNPACKING

1. Cut the shipping carton along the dotted line along tile

bottom. Remove the carton.

2. Using a rug, blanket or piece of cardboard to protect the

floor, lay the washer on it's back.

3. Remove and savethe styrofoam base and shipping plug.

Shoping

Base Plug

\

Drain Hose Installation
The drain hose isfield installed to allow hose orientation to the

left or right, up or down depending on location of the house
drain. The hose is shipped in the washer tub with the spring
clamp on the coupler elbow and drain hose hanger installed on

the end of the hose.

1. Remove the drain hose from the tub of the washer.

2. Pushthe hose onto the drain coupler at the upper left of the
washer back panel until the hose contacts the STOPRIB.

STOP RIB

!i

ti

X\\ n

PUSH HOSE ONTO

COUPLER TO STOP RIB

DRAIN

HOSE TABS

SPRING
CLAMP

PROVIDED

: ON HOSE

INSTALLATION

Zeve//ng the Washer
Excessive noise and vibration can be prevented by properly
leveling the washer.

Forfree standing installation and with the washer in it's
final position, place a level on top of the washer. Adjust
the leveling legs so the washer is level fronbto-rear and

side4o-side, and stable corner-to-cornen

Pressdown on alternate corners and sides and feel for the

slightest movement, Adjust the appropriate leg so the
washer is SOLID on the floor on ALL four legs, Keep the
leveling leg extension at a minimum for best performance

of the washer,

.

Using pliers, squeeze the ears of the spring clamp

and position the (:lamp so the (:lamp ears aH_n with
and contact the tabs on the drain hose. This assures

proper location of tile (:lamp to prevent leaks.

ALIGN SPRING

CLAMP EARS WITH
TABS ON HOSE

'X

/

/

/'

/

i

..//

2. For pedestal installations Seeadditional installation
instructions included with the pedestal.

Washer Connections

1. Run some water from the hot and cold
faucets to flush the water lines and

remove particles that might clog up the
water valve screens,

.

Remove the inlet hoses and rubber
washers from the plastic bag located in

the drum of the washer and install the
rubber washers in each end of the inlet
hoses.

.

Carefully connect the inlet hose marked "HOT" to the
outside "H" outlet of the water valve. Tighten by hand, then
tighten another 2/3 turn with pliers. Carefully connect the

other inlet hoseto the inside "C" outlet of the water valve.
Tighten by hand, then tighten another 2/3 turn with pliers.

Do not crossthread or over-tighten these connections.

.

Connect the inlet hose ends to the HOT and COLD water
faucets tightly by hand, then tighten another 2/3 turn with

pliers. Turn the water on and check for leaks.
NOTE: Use only new hoses.

INSTALLATION (CON'T)

Placethe hook end of the drain hose in the drain
opening. Secure the drain hose with the cable tie

(provided in the enclosure package) to the standpipe,
inlet hose, laundry tub, etc. so the hose does not pull

out from the force of the water.

Plug the power cord into a grounded outlet.

NOTE: Check to ensure the power is off at a circuit

breaker/fuse box before plugging the power cord
into an outlet.

7. Turn on tile power at a circuit breaker/fuse box.

8. Read the Operating Instructions and Owner's Guide

provided with the washer. They contain valuable and helpful
information that will save you time and money.

Cable Tie

Cable Tie

Cable Tie

9. Run thewasherthrough a complete cycle. Check for water

leaks and proper operation.

10. Ifyou rwasher does not operate, please review the "Avoid

Service Checklist" in your Owner's Guide before calling

for service.

11. Placethese instructions in a location near the washer for
future reference.

NOTE: A wiring diagram and technical data sheet are located

in an envelope attached to tile left hand side panel on

the inside of the washer.

Pedestal

A pedestal accessory, Model No. APWDI5W, specifically

designed for this washer may beusedwhen elevating the washer

for ease of use. Failure to use accessories certified by the

manufactu rercould result in personal injury, property damage or
damage to the washer.

REPLACEMENT PARTS

If replacements parts are needed for your washer, contact tile
sourcewhere you purchased your washer, call 1-800-944-9044,
or visit our website, www.frigidaire.com, for the Frigidaire
Company Authorized Parts Distributor nearest you.

Destroy the carton and plastic bags after the

washer isunpacked. Children might use them for play.Cartons

covered with rugs, bedspreads, or plastic sheets can become
airtight chambers causing suffocation. Place all materials in
a garbage container or make materials inaccessible to

children.

The instructions in this manual and all other

literature included with this washer are not meant to cover
every possible condition and situation that may occur. Good

safe practice and caution MUST be applied when installing,
operating and maintaining any appliance.

]

the Safety and Operating instructions are understood and

Maximum benefits and enjoyment are achieved when all|

1practiced as a routine with your laundering tasks.