Frigidaire ATF6000ES0, ATF6000ES1, ATF7000EP0, ATF7000ES0, ATF7000ES1 Installation Guide

Full Size Tumble Action Washers

Before beginning installation, carefully read these instructions. This will simplify the
instaffation and ensure the washer is installed correctly and safely. Leave these instructions

near the washer after installation for future reference.

NOTE: The electrical service to the washer must conform with local codes and ordinances
and the latest edition of the National Electrical Code, ANSI/NFPA 70.

Contents

For your safety the information in

this manual must be followed to minimize the risk

of fire or explosion or to prevent property damage,
personal injury or loss of life.

- Do not store or use gasoline or other flammable
vapors and liquid in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

. Do not try to light any appliance.
. Do not touch any eIectrica[ switch; do not

use any phone in your building.

. Clear the room, building or area of all

occupants.

. immediately call your gas supplier from a

neighbor's phone. Follow the gas suppliers
instructions.

. if you cannot reach your gas supplier, call

the fire department.

SUBJECT PAGE

Preqnstallation Requirements 2

Electrical Requirements 2
Grounding Requirements 2
Water Supply Requirements 2

Drain Requirements 2

Roughqn Dimensions 3

Location Of Your Washer 4

Unpacking 4

Installation 5-6

Replacement Parts 6

installation and service must be performed by a
qualified installer, service agency or the gas
supplier.

Printed in U.S.A.

P/N 134602900A (0512)

PRE-INSTALLATION REQUIREMENTS

Tools Required for Installation:

1. Phillips screwdriver

2. 10 mm socketwith ratchet.

3. Channeldock adjustable pliers.

4. Carpenter's level.

absence of local codes, with tile National Electrical
Codes, ANS!/NFPA 70 (latest edition). If in doubt,

call a licensed electrician. DO NOTcut off or alter
the grounding prong on the power supply cord. In

situations where a two-slot receptacle is present,

it is tile owner's responsibility to have a licensed
electrician replace it with a properly grounded
three prong grounding type receptacle.

ELECTRICAL REQUIREMENTS

CIRCUIT-Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2 wire, with ground, 120 volt, single
phase, 60 Hz, Alternating Current. NOTE: Because of
potential inconsistent voltage capabilities, the useof this
washer with power created by gas powered generators,
solar powered generators, wind powered generators or
any other generator other than the local utility company

is not recommended.

OUTLET RECEPTACLE- Properly grounded 3-prong
receptacle to be located so the power supply cord is

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within

42 inches (!07 cm) of your washer's water inlet. Tile
faucets MUST be 3/4 inch (1.9 cm) garden hose type
so inlet hoses (:anbe connected. Water pressure MUST

be between30 and 120 pounds persquareinch (maximum

unbalance pressure, hot vs. cold, 10 psi.) "four water
department (:anadviseyou of yourwater pressure.Thehot
water temperatureshouldbeabout 140degreesF(60degrees
C).

DRAIN REQUIREMENTS

1. Drain capable of eliminating 17 gals (64.3 L) per
minute.

2. A standpipe diameter of I-I/4 in. (3.18 cm)
minimum.

3. The standpipe height above the floor should be:

Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244cm)

accessible when the washer is in an installed position.

NOTE: GFI(Ground Fault Interrupter) receptacle is not

required.

GROUNDING REQUIREMENTS

Improper connection of the equipment

grounding conductor (:an result in a risk of electrical
shock. Check with a licensed electrician if you are in
doubt asto whether the appliance is properly grounded.

.

Tile washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electrical shock by a path of least

resistance for electrical current.

.

Sinceyour washer is equipped with a power supply
cord having an equipment-grounding conductor
and a grounding plug, tile plug MUSTbe plugged
into an appropriate, copper wired receptacle that
is properly installed and grounded in accordance

with all local codes and ordinances or in tile

o O0

24 in.

(61 cm)

MJn,

BACK

NOTE:

Drain hose attached to the washer can reach a gO
in. (229 cm) high standpipe. For higher standpipe,

use hose P/N 134369410, available from an

authorized parts distributor.

T

96 in.

(244 cm)

Max.