French User’s Manual ............................................ 19-27
www.frigidaire.comUSA & Canada 1-888-845-7330
IMPORTANT SAFEGUARDS
When using electrical appliances, basic
safety precautions should always be
followed, including the following:
1.Read all instructions.
2.Avoid contact with moving parts.
3.To protect against electric shock, do not place cord,
plugs, or appliance in water or other liquid.
4.Close supervision is necessary when any appliance
is used by or near children.
5.Unplug from outlet when not in use, before putting
on or taking off parts, and before cleaning.
6.Do not operate any appliance with a damaged cord
or plug, or after the appliance malfunctions, or is
dropped or damaged in any manner. Return the
appliance to the nearest authorized service center
for inspection, repair, or electrical or mechanical
adjustment.
7.Do not use outdoors.
8.Do not let cord touch hot surfaces, including the
stove, or hang over edge of table or counter where it
can be pulled on by children or tripped over
unintentionally.
9.Do not place on or near a hot gas or electric burner,
or in a heated oven or in a microwave oven.
10.Do not use this appliance for any purpose other than
its intended use.
11.Do not submerge the motor unit in water or liquids,
to avoid possible electrical shock.
12.The use of attachments including canning jar not
recommended or sold by the manufacturer may
cause fire, electrical shock, or injury.
13.Place the blender on a dry, even surface.
14.To disconnect blender, press the OFF button to be
sure the unit is turned off. Then unplug by grasping
the plug and pulling out from the wall outlet. Never
unplug by pulling on the cord.
15.Always use your blender with the lid in place.
16.Do not remove the jar from the motor unit while the
unit is running.
17.BLADES ARE SHARP. HANDLE CAREFULLY.
18.Keep hands and utensils out of container while
blending to reduce the risk of severe injury to
persons or damage to the blender. A scraper may be
used but must be used only when the blender is not
running.
19.Never leave blender unattended while it is running.
20.Before using the unit for the first time, wash the
blender jar, cutting assembly, locking ring, and lid.
21.Do not place boiling or hot liquids in the jar. Allow
liquids to cool before placing in the jar.
22.Do not place the unit near any hot surface, range or
electrical burners, or where it could touch any other
source of heat.
23.Add liquid ingredients to the jar first; then add dry
ingredients to get uniformly mixed.
24.When mixture is heavy or thick, blend for 10 seconds
and turn off the unit. Stir the mixture before
continuing blending.
25.To reduce the risk of injury, never place cutter-
assembly blades on base without jar property
attached.
SAVE THESE INSTRUCTIONS
Consumer Safety Information
THIS UNIT IS FOR HOUSEHOLD USE ONLY.
Polarized Plug
This appliance has a polarized plug (one blade is wider
than the other). To reduce the risk of electric shock, this
plug will fit in a polarized outlet only one way. If the plug
does not fit fully into the outlet, reverse the plug and
reinsert. If it still does not fit, contact a qualified
electrician. Do not modify the plug in any way.
CAUTION
Short cord Instructions: Your blender appliance is
equipped with a short power supply cord as a safety
precaution to prevent personal injury or property
damage resulting from pulling, tripping or becoming
entangled with a longer cord. Do not allow children to
use or be near this appliance without close adult
supervision. An extension cord is available and may be
used if care is exercised in its use. If an extension cord
is used, (1) the marked electrical rating of the cord set
or extension cord should be at least as great as the
electrical rating of the appliance, (2) the cord should be
arranged so that it will not drape over the countertop
or tabletop where it can be pulled on by children or
tripped over unintentionally, (3) If the appliance is of
the grounded type, the extension cord should be a
grounding 3-wire cord.
WARNING
Electrical Shock Hazard
Plug the unit into a properly grounded electrical outlet.
Failure to follow these instructions can result in death,
fire, or electrical shock.
2
PARTS AND FEATURES
PROFESSIONAL
on/off
low
high
crush
ice
smoothie
pulse
Pouring Insert Cover
Lid
Glass Jar
Gasket
Power Blade Assembly
56-Ounce Jar
Your Household Blender comes with a 56-ounce glass jar.
This generous-sized jar will handle the blending needs for
all your favorite recipes, from chopping nuts to mixing
salad dressings to pureeing baby food, and much more.
Pouring Insert
This feature allows you to add ingredients to the jar
without removing the lid. Just lift off the pouring insert
cover to pour or stream in liquids or drop in dry
ingredients while blending.
Automatic ‘Off’ Feature
Your blender is equipped with an automatic shut-off
feature. If the blender control button is left ‘On’ but the
blender is not operated for 30 minutes, the blender will
automatically turn off. In the event you forget to turn the
appliance off and unplug it after using, this feature will
prevent unnecessary power usage.
2 Speeds, 3 Special Functions
‘High’ and ‘Low’ settings allow you to blend ingredients
at the desired speed. Your blender also includes three
special functions – Pulse, Smoothie, and Crush Ice – with
each function pre-set to the appropriate speed for these
specialized jobs.
Locking Collar
Motor Base
Push-Button Controls
Electrical Power
If the electric circuit is overloaded with other appliances,
your appliance may not operate properly. It should be
operated on a separate electric circuit from other
appliances.
Product Specifications
Model NumberFPJB56B7MS
Volts120V AC only
Rated Wattage600 watts
Hertz60 HZ
DimensionsWidth 7 1/16 in. (17.9 cm)
Depth 9 in. (22.9 cm)
Height 16 1/4 in. (41.4 cm)
Capacity56 ounces (1650 ml)
3
PRIOR TO USING YOUR BLENDER
sket
erblade
nder
gCollar
CAUTION
Unpack carefully. Blades are very sharp!
1.Carefully unpack the contents from the box. Check to
make sure all pieces (as shown on page 3) are
accounted for and that the blender appears to be free
of any physical damage. If you discover any damage
or missing parts, please contact our customer service
department at 1-888-845-7330 prior to plugging in the
unit.
2.Remove any printed material or tape from the blender.
Inspect the jar to be sure there are no packaging
materials or foreign materials inside.
3.After inspection, place the blender motor base upright
on a countertop or table.
4.Before using, wash the lid, pouring insert cover, glass
jar, gasket, and power blade assembly in warm soapy
water or in a dishwasher. (To disassemble, see
instructions on page 6.) Dry thoroughly.
5.Wipe the motor base with a damp cloth.
6.Assemble the blender following the instruction on this
page.
HOW TO ASSEMBLE YOUR BLENDER
CAUTION
Blades are very sharp.
When handling the power blade assembly, hold
assembly by its base. Avoid handling blades with your
fingers.
1.Place the motor base on a flat, dry surface.
Locking
Collar
2.Assure that the motor in turned off and the power
cord is unplugged.
3.Turn the glass jar upside down on a flat, sturdy
surface.
4.Place the gasket over the jar bottom opening.
5.Insert the power blade assembly into the jar opening.
6.Place the locking collar on top of the blade assembly
and twist clockwise to lock firmly.
7.Turn the jar upright and place it on the motor base.
8.Place the lid on top of the jar. Insert the pouring insert
cover into the blender lid and turn until it locks.
9.Plug the power cord into a 120-volt outlet. Your
blender is now ready to use.
CAUTION
Add food or liquid while the blender is running only by
lifting the pouring insert cover and dropping in the
ingredients. Never remove the lid while blender is
running.
Power Blade Assembly
Gasket
Glass Jar
4
USING YOUR BLENDER
To Use Your Blender
• Plac e food in blender jar, being careful not to overfill.
• Pres s the ON/OFF button. T he c lear LED indicator light
will illuminate, indicating that the blender is turned on
but no s peed has b een s elected.
• Pres s the ‘Low’ or ‘High’ button to selec t your des ired
proces s ing s peed, or choose one of 3 special functions.
Choosing Speed
StepsPress
1.Press ON/OFF. L ight will indicate the
blender is on.
2.Press the desired s peed. Light will
indicate the speed s elected.
3.To paus e, press the s peed button
again. The unit will stop blending
and remain on in standby mode.
4.Press the s peed button again to
resume blending.
5.When finished, pres s ON/OFF to
turn off the blender. Light will go off.
Tip: Yo u can change the s peed while the blender is
running without turning the unit off. J ust pres s the
selec ted speed to paus e; then pres s another s peed to
resume blending.
When Finished Blending
Pulse Function
Use the ‘Pulse’ button when you need a s hort burst of
power. This function is us eful for chopping nuts , for
breaking up large piec es of food, or for foods that require
minimal blending.
StepsPress
1.Press ON/OFF. L ight will indicate the
blender is on.
2.Press ‘Pulse.’ Light will indic ate the
function selec ted.
3.Press ON/OFF to turn off the blender.
Light will go off.
Smoothie Function
This function lets you prepare your favorite smoothie
effortles s ly.
of power to get the ice crushed and your smoothie
blended to the des ired consistency.
StepsPress
1.Press ON/OFF. L ight will indicate the
blender is on.
2.Press ‘S mooth.’ L ight will indicate the
function selec ted.
3.When you get the consistency desired,
pres s ON/OF F to turn off the blender.
Light will go off.
Using this function will give you a burst
• Turn the unit off and unplug from elec trical outlet.
• Lift the jar straight up and off the motor base – do not
twist the jar or locking c ollar when removing from the
motor bas e.
• After cleaning, s tore the jar upright, in or alongside the
motor bas e, with the lid and pouring insert cover in
place. Do not place other items on top of stored blender.
CAUTION
Do not blend above maximum capacity.
When using the blender with the jar filled at or near or
maximum c apacity, rest your hand on the blender lid to
stabilize it. This w ill help avoid an y movement or
displacement while blending.
Crush Ice Function
This function lets you crush ice without adding liquid. It
works in a ‘pulse’ mode, giving the burst of power to
crush ice as des ired. L oad ice c ubes in the blender jar and
proces s until ice is crus hed to desired fineness. F or bes t
results, work in small batches .
StepsPress
1.Press ON/OFF. Light will indicate the
blender is on.
2.Press ‘C rus h.’ Light will indicate
the function selected.
3.When finished, pres s ON/OFF to
turn off the blender. Light will go off.
5
CLEANING YOUR BLENDER
sket
erblade
nder
gCollar
IMPORTANT
➡
Unplug the blender from electrical outlet before cleaning.
• To disassemble, empty the jar and turn upside down.
Turn locking collar counter-clockwise to unlock. Lift of
locking collar, power blade assembly and gasket.
• Handle the power blade assembly carefully.
It is SHARP and may cause injury. Do not attempt to
remove blades from cutting assembly.
• Wipe the motor base with a soft damp cloth and dry it
thoroughly.
• Wipe the power cord with a damp cloth.
Locking
Collar
• Wash the jar, lid, pouring insert cover, gasket, blade
assembly and locking collar in warm soapy water. If
there are any stubborn foods, use a brush to free
residual food. Rinse all parts and dry thoroughly.
• If you desire, the jar can be washed using the
dishwasher on a normal cycle, in upside-down position.
Lid, pouring insert cover, gasket, power blade assembly
and locking collar are also top-rack dishwasher-safe.
• You may also wash the power blade assembly by
adding 1 cup of warm soapy water to blender jar.
Operate on ‘Low’ speed for 30 seconds. Empty jar. Add
clear warm water and operate another 30 seconds to
rinse. Carefully disassemble parts, rinse in clear warm
water and dry thoroughly.
• For stubborn or strong stains and odors: Soak the jar
and lid for 5 minutes in a detergent solution. Rinse with
clear warm water and dry thoroughly.
CAUTION
Power Blade Assembly
Gasket
Glass Jar
CAUTION
Never submerge the motor
base in water or another
liquid. Never place the motor
base in a dishwasher. The
motor base is designed to be
resistant to liquids, but must
not be submerged in water.
6
• Never use scouring pads or
abrasive cleaners on the
motor base, as this can
scratch or damage the
finish.
• Do not use bleach solutions
to clean the motor base, as
bleach can damage the
stainless steel finish.
TIPS FOR BEST USE
DO:
❑Use ‘Low’ button for drinks or cocktails,
mayonnaise, dressings, marinades, and any
food which needs to get batters with
consistency.
❑Use ‘High’ button for pureeing soups or
liquefying any food.
❑Use ‘Pulse’ button to get a quick burst of
power for a short period of time, such as for
chopping onions, nuts or grains.
❑Use ‘Crush’ button to crush ice. For best
results, work in small batches.
❑For even results, cut foods into 1/2- to 1-inch
cubes before processing.
❑For uniformly mixed ingredients, add liquids to
the jar first; then add remaining solid
ingredients.
❑Remove the pouring insert cover to add
ingredients without interrupting blender
operation. Put the pouring insert cover back in
place after ingredients have been added.
❑Operate the blender with the lid on.
❑Make sure the locking collar is tightly attached
to the jar before operating blender.
❑Remove locking collar and power blade
assembly before cleaning.
❑When blending thick mixtures, turn blender off
to scrape sides of the blender with a spatula.
❑When chopping dry foods such as fresh herbs
or bread crumbs, make sure the jar and power
blade assembly are completely dry.
DO NOT:
❑Do not blend heavy mixtures for longer than 1
minute. Press the speed button (Low or High)
to pause and allow mixture to rest; then press
again to restart.
❑Do not use blender jar as storage for liquids or
mixtures.
❑Do not use your blender without the lid on
tightly. If you need to add ingredients, remove
the pouring insert cover and pour or drop in
ingredients. Replace pouring insert cover after
adding ingredients.
❑Do not place very hot or boiling liquids in the
jar. Allow food to cool before placing in the jar.
❑Do not remove the jar while the motor in
running.
❑Do not use the blender to knead dough, mash
potatoes, or create meringues with egg whites.
The blender is not designed for these tasks.
❑Do not overload the blender. This can cause
the motor to stall.
❑Do not over-blend your food. Most desired
results are obtained in a few seconds.
❑Do not use any utensil inside the jar while
blender is running.
❑Do not remove locking collar while the jar is on
the motor base. Remove jar from the base and
twist counter-clockwise to remove the locking
collar.
❑Do not use any accessories not recommended
by the manufacturer. This could result in injury.
❑Do not place hands inside the blender when
the blender is plugged into an outlet.
❑If food sticks to the sides of the blender jar,
use the ‘Pulse’ button to work in short bursts.
7
PROBLEM SOLVING
ProblemSolutions
Blender does not turn on.• Check to be sure the power plug is securely inserted into the
outlet.
• Make sure the ON/OFF pad is illuminated. If not, press
ON/OFF to turn blender on.
• Touch the desired speed.
• If blender still does not turn on, check for a blown fuse or
reset the circuit breaker.
Food is spattering outside the jar.• Be sure the lid is on the jar securely before blending.
• Operate the blender on low setting while you remove the
pouring insert cover to add new ingredients.
• Do not overload the jar. If the jar is too full, turn the blender off
and remove some of the mix.
The motor base is bogging down.• Be sure the blender is not overloaded. If the jar is too full or
mixture is very thick, turn off the blender, remove some of the
mix, and re-start the process.
• Cut foods into even-sized pieces, 1/2- to 1-inch cubes, before
processing.
• When using the ‘Smooth’ or ‘Crush’ setting, break any large
chunks of ice into smaller pieces before adding to blender.
Blender jar is leaking at the bottom.• Be sure the gasket is in place between the jar and the power
blade assembly.
• Check the locking collar to be sure it is aligned properly and
securely fastened to blender jar.
8
SMALL DOMESTIC APPLIANCE WARRANTY
Your appliance is covered by a one-year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove
to be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
ExclusionsThis warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
If You NeedKeep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
Serviceshould service be required. If service is performed, it is in your best interest to obtain and keep all
receipts. Service under this warranty must be obtained by contacting Electrolux at the addresses
or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.
USACanada
1.888-845-73301.888-845-7330
Electrolux Home Products, Inc.Electrolux Canada Corp.
10200 David Taylor Drive5855 Terry Fox Way
Charlotte, NC 28262Mississauga, Ontario, Canada
L5V 3E4
Printed in China
Loading...
+ 18 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.