Frigidaire 241695301 User Manual

P/N 241695301 (0106)

WELCOME & CONGRATULATIONS

Congratulations on your purchase of a new refrigerator! We
here at Electrolux Home Products, Inc. are very proud of our
product and we are completely committed to providing you
with the best service possible. Your satisfaction is our #1
priority.

Please read this Use & Care Manual very carefully. It contains
valuable information on how to properly maintain your new
refrigerator.

We know you’ll enjoy your new refrigerator and Thank You for
choosing our product. We hope you consider us for future
purchases.

PLEASE READ AND SAVE THESE INSTRUCTIONS

This Use & Care Manual provides specific operating
instructions for your model. Use your refrigerator only as
instructed in this manual. These instructions are not meant to
cover every possible condition and situation that may occur.
Common sense and caution must be practiced when installing,
operating and maintaining any appliance.

Please record your model and serial numbers below for
future reference. This information is found on the serial
plate located inside the refrigerator compartment.

NOTENOTE

NOTE

NOTENOTE

Use only soap and water to clean serial plate.

Questions?

1-800-944-9044

(United States)

1-800-265-8352

(Canada)

or visit our web site at www.frigidaire.com

Extend Your Warranty Protection

With An

Extended Service Contract

CALL 1-800-944-9044

To Enjoy These Benefits:

• Total freedom from repair bills so
unexpected repairs won’t upset your budget.

• Fast, convenient toll-free service is just a
phone call away.

• Top-quality repairs by factory-trained
experts.

Model Number:
Serial Number:
Purchase Date:

pÉêá~ä =mä~íÉ

Please attach sales receipt here for future reference.

• Quick access to genuine replacement
parts so you can rest assured your

refrigerator is repaired with the proper
components.

PLEASE COMPLETE AND MAIL IN THE

REGISTRATION CARD

INCLUDED WITH YOUR

REFRIGERATOR .

PRODUCT

2

IMPORTANT SAFETY INSTRUCTIONS

FOR YOUR SAFETY

• Do not store or use gasoline, or other flammable liquids in
the vicinity of this or any other appliance. Read product
labels for warnings regarding flammability and other
hazards.

• Do not operate the refrigerator in the presence of
explosive fumes.

• Avoid contact with any moving parts of automatic ice
maker.

• Remove all staples from the carton. Staples can cause
severe cuts, and also destroy finishes if they come in
contact with other appliances or furniture.

CHILD SAFETY

Destroy or recycle the carton, plastic bags, and any exterior
wrapping material immediately after the refrigerator is
unpacked. Children should NEVER use these items to play.
Cartons covered with rugs, bedspreads, plastic sheets or
stretch wrap may become airtight chambers, and can quickly
cause suffocation.

PROPER DISPOSAL OF YOUR REFRIGERATOR OR
FREEZER

Risk of child entrapment

Child entrapment and suffocation
are not problems of the past.
Junked or abandoned
refrigerators or freezers are still
dangerous – even if they will sit for
“just a few days.” If you are getting
rid of your old refrigerator or
freezer, please follow the
instructions below to help prevent
accidents.

Before you throw away your old refrigerator/ freezer:

• Remove doors.

• Leave shelves in place so children may not easily climb
inside.

• Have refrigerant removed by a qualified service
technician.

ELECTRICAL INFORMATION

• The refrigerator must be plugged into its own dedicated
115 Volt, 60 Hz., AC only electric outlet. The power cord

of the appliance is equipped with a three-prong grounding
plug for your protection against electrical shock hazards. It
must be plugged directly into a properly grounded three­prong receptacle. The receptacle must be installed in
accordance with local codes and ordinances. Consult a
qualified electrician. Do not use an extension cord or

adapter plug.

• If the power cord is damaged, it should be replaced by the
manufacturer, service technician or a qualified person to
prevent any risk.

• Never unplug the refrigerator by pulling on the power
cord. Always grip the plug firmly, and pull straight out
from the receptacle to prevent damaging the power cord.

• Unplug the refrigerator before cleaning and before
replacing a light bulb to avoid electrical shock.

• Performance may be affected if the voltage varies by
10% or more. Operating the refrigerator with insufficient
power can damage the compressor. Such damage is
not covered under your warranty.

• Do not plug the unit into an outlet controlled by a wall
switch or pull cord to prevent the refrigerator from being
turned off accidentally.

• Avoid connecting refrigerator to a Ground Fault Interruptor
(GFI) circuit.

3

INSTALLATION

This Owner’s Guide provides specific operating instructions for
your model. Use the refrigerator only as instructed in this Use &
Care Manual. Before starting the refrigerator, follow these

important first steps.

LOCATION

• Choose a place that is near a grounded electrical outlet.
Do Not use an extension cord or an adapter plug.

• If possible, place the refrigerator out of direct sunlight
and away from the range, dishwasher or other heat
sources.

• The refrigerator must be installed on a floor that is level
and strong enough to support a fully loaded refrigerator.

• Consider water supply availability for models equipped
with an automatic ice maker.

INSTALLATION

CAUTION CAUTION

CAUTION

CAUTION CAUTION

Do Not install the refrigerator where the temperature
will drop below 55°F (13°C) or rise above 110°F (43°C).
The compressor will not be able to maintain proper
temperatures inside the refrigerator.

Do Not block the toe grille on the lower front of your
refrigerator. Sufficient air circulation is essential for the
proper operation of your refrigerator.

Installation Clearances

• Allow the following clearances for ease of installation,
proper air circulation, and plumbing and electrical
connections:

Sides & Top ------------------ 3/8”
Back --------------------------- 1”

DOOR OPENING

NOTENOTE

NOTE

NOTENOTE

To Remove Toe Grille:

1. Open freezer and fresh food compartment doors.

2. Working from left side of toe grille, slip your fingers
between top of toe grille and cabinet. Gently pull
forward until first set of
tabs are free. Slide
your hand down past
the free tabs and pull
forward again until the
second set of tabs are
free. Continue this
process until all tabs
are free and the toe
grille can be removed.
(See graphic at top of
page in right column.)

LEVELING

All four corners of your refrigerator must rest firmly on a solid floor.
Your refrigerator is equipped with adjustable front rollers to help level
your unit. To ensure proper door seal and assist door closing, the
refrigerator should be tilted 1/4” (6 mm), front to back.

To Level Your Refrigerator:

1. Remove toe grille. (See

2. Use flat-blade screwdriver or 3/8” socket wrench to adjust
front rollers.

“To Remove Toe Grille”

.)

If you refrigerator is placed with the door hinge side
against a wall, you may have to allow additional space so
the door can be opened wider.

Your refrigerator should be positioned to allow easy access to a
counter when removing food. For best use of drawers and
freezer baskets, the refrigerator should be in a position where
both the refrigerator and freezer doors can be fully opened.

TOE GRILLE INSTALLATION / REMOVAL

To Install Toe Grille:

1. Open freezer and fresh food compartment doors.

2. Line up toe grille at base of refrigerator, making sure the
four bottom tabs are resting through holes at base of
cabinet.

3. Starting from left side of toe grille, press in on first top tab
using your thumb and push toe grille forward until it snaps
in place. Continue this process until all tabs are snapped
in place and toe grille is secured to refrigerator.

NOTENOTE

NOTE

NOTENOTE

The refrigerator doors are designed to shut by themselves
within a 20 degree opening.

3. Check both doors to be sure seals touch cabinet on all four
sides.

4

INSTALLATION - CONNECTING ICE MAKER TO WATER SUPPLY

WARNING WARNING

WARNING

WARNING WARNING

To avoid electric shock, which can cause death or
severe personal injury, disconnect the refrigerator from
electrical power before connecting a water supply line
to the refrigerator.

CAUTION CAUTION

CAUTION

CAUTION CAUTION

To Avoid Property Damage:

• Copper tubing is recommended for the water supply

line. Water supply tubing made of ¼” plastic is not
recommended since it greatly increases the potential
for water leaks. Manufacturer will not be responsible
for any damage if plastic tubing is used for supply
line.

• DO NOT install water supply tubing in areas where
temperatures fall below freezing.

• Chemicals from a malfunctioning softener can
damage the ice maker. If the ice maker is connected
to soft water, ensure that the softener is maintained
and working properly.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON
water supply and flush supply line until water is clear. Turn
OFF water supply at shutoff valve.

3. Unscrew plastic cap from water valve inlet and discard
cap.

4. Slide brass compression nut, then ferrule (sleeve) onto
water supply line, as shown.

5. Push water supply line into water valve inlet as far as it will
go (¼ inch). Slide ferrule (sleeve) into valve inlet and
finger tighten compression nut onto valve. Tighten another
half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to
rear panel of refrigerator as shown.

7. Coil excess water supply line (about 2½ turns) behind
refrigerator as shown and arrange coils so they do not
vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any
connections that leak.

9. Reconnect refrigerator to electrical power source.

10. To turn ice maker on, lower wire signal arm (side
mounted) or set the ice maker’s On/Off power switch to the
“I” position. (rear mounted)

IMPORIMPOR

IMPOR

IMPORIMPOR

Ensure that your water supply line connections comply
with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need:

• Basic Tools: adjustable wrench, flat-blade screwdriver,

• Access to a household cold water line with water pressure

• A water supply line made of ¼ inch (6.4 mm) OD, copper

• A shutoff valve to connect the water supply line to your

• A compression nut and ferrule (sleeve) for connecting the

NOTENOTE

NOTE

NOTENOTE

Water line kit number 5303917950, available from your
appliance dealer at additional cost, contains 25 feet (7.6
meters) of ¼ inch OD copper tubing, a saddle type shutoff
valve (nonpiercing), (2) ¼ inch brass compression nuts, (2)
ferrules/sleeves, and instructions for installing a water
supply line.

TT

ANTANT

T

ANT

TT

ANTANT

and PhillipsTM screwdriver

between 30 and 100 psi.

tubing. To determine the length of copper tubing needed,
you will need to measure the distance from the ice maker
inlet valve at the back of the refrigerator to your cold water
pipe. Then add approximately 7 feet (2.1 meters), so the
refrigerator can be moved out for cleaning (as shown).

household water system. DO NOT use a self-piercing type
shutoff valve.

water supply line to the ice maker inlet valve.

5

DOOR REMOVAL INSTRUCTIONS:

If it is necessary to move the refrigerator through narrow doorways, follow
these steps to remove the doors.

6

FEATURES AT A GLANCE

FEATURES MAY VARY ACCORDING TO MODEL

7

LOOKING INSIDE

PIZZA SHELF (SOME

MODELS)

This shelf is attached to the
freezer wall beside the ice
dispenser container. This
convenient area allows for
storage of pizza and other tall
items placed vertically between
the ice dispenser container and
the freezer wall.

ICE CREAM SHELF (SOME MODELS)

This shelf attaches to the top of
the ice dispenser container. It
allows storage of both round and
rectangular cartons of your
favorite ice cream.

TIP-UP SHELF (SOME

MODELS)

A Tip-Up shelf in the freezer
section allows tall items to be
easily stored.

Pizza Shelf

Ice Cream Shelf

CANTILEVER SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted to suit individual
needs. Before adjusting the shelves, remove all food.
Cantilever shelves are supported at the back of the refrigerator.

To adjust cantilever shelves:

1 Lift front edge up.

2 Pull shelf out.

Replace the shelf by inserting the hooks at rear of the shelf into
the wall bracket. Lower the shelf into the desired slots and lock
into position.

* SpillSafeTM

accidental spills. In some models, the
out for easy access to food and for fast cleaning. The shelves
slide out independently of their mounting brackets. Just pull the
front of the shelf forward. Shelves can be extended as far as the
stopper will allow but are not removable from their mounting
brackets.

glass shelves (some models) catch and hold

* SpillSafe

1

TM

shelves slide

1

2

CAUTION CAUTION

CAUTION

CAUTION CAUTION

To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break
suddenly if nicked, scratched, or exposed to sudden
temperature change.

ADJUSTABLE DOOR BINS

Some models have adjustable door bins that can be moved to
suit individual needs.

To move door bins

1. Lift bin straight up.

2. Remove bin.

3. Place bin in desired position.

4. Lower bin onto supports until locked in place.

2

Cantilever Glass Shelf

Cantilever Sliding Glass Shelf

DOOR STORAGE

Door bins and shelves are provided for convenient storage of
jars, bottles, and cans. Frequently used items can be quickly
selected.

Some models have door bins that can accommodate gallon­sized plastic drink containers and economy-sized jars and
containers. Some bins are adjustable for maximum storage
capacity.

The dairy compartment, which is warmer than the general food
storage section, is intended for short term storage of cheese,
spreads, or butter.

Adjustable Door Bin

* WhiteWestinghouse - SpillFree

Fixed Door Bin

TM

8

LOOKING INSIDE (CONTINUED)

TALL BOTTLE RETAINER (SOME MODELS)

The Tall Bottle Retainer keeps tall containers in the bin from
falling forward when opening or closing the refrigerator door.
To install, hold the retainer at the top, and slide it over the
outside wall of the bin, as shown in the diagram. The Tall
Bottle Retainer works best with a Bin Snugger.

Tall Bottle Retainer (left) and Bin Snugger (right)

SPECIAL ITEM RACK

(SOME MODELS)

The innovative design of
the Special Item Rack
allows you to store a six­pack of 12 ounce drink

9

AUTOMATIC ICE AND WATER DISPENSER

AUTOMATIC ICE & WATER DISPENSER OPERATING INSTRUCTIONS

10

AUTOMATIC ICE AND WATER DISPENSER

AUTOMATIC ICE & WATER DISPENSER OPERATING INSTRUCTIONS

11

AUTOMATIC ICE AND WATER DISPENSER

12

AUTOMATIC ICE AND WATER DISPENSER

CAUTION CAUTION

CAUTION

CAUTION CAUTION

If the dispensing paddle is pushed for more than 4
minutes, the dispenser motor may overload and stop.
The overload protector will reset automatically after 3
or 4 minutes.

• If a large quantity of ice is needed at one time, it is best to
remove cubes directly from the ice container.

• The following sounds are normal when the ice maker is
operating:

• Motor running

• Ice dropping into ice container

• Water valve opening or closing

• Ice loosening from tray

• Running water

• Stop the ice maker when cleaning the freezer and during
vacations.

• If the ice maker will be turned off for a long period of time,
turn the water supply valve to the closed position.

CLEANING THE ICE DISPENSER

Clean the dispenser and ice container at regular intervals,
particularly before you take a vacation or move, or if the ice
dispenser sticks.

1. Stop ice production by lifting the wire signal arm to the
"up" or OFF position (side mounted) or the ice maker’s On/
Off power switch turned Off-set to the “O” position (rear

mounted) .

2. Remove ice container by lifting up and out. Empty and
carefully clean the container with mild detergent. Rinse
with clear water. Do not use harsh or abrasive cleaners.
Allow ice container to dry completely before replacing in
the freezer.

3. Remove ice chips and clean the shelf and chute that
supports the ice container.

4. Replace the ice container. Lower the wire signal arm on
the ice maker to the "down" or ON position (side
mounted) or the ice maker’s On/Off power switch is turned

On-set to the “I” position. (rear mounted)and the ice
maker will resume production.

IMPORIMPOR

IMPOR

IMPORIMPOR

When removing or replacing the ice bin, do not rotate the
auger in the ice bin. If the auger is accidentally turned, you
must realign the auger by turning it in 90° turns until the ice
bin fits into place with the drive mechanism.

TT

ANTANT

T

ANT

TT

ANTANT

Remove and empty the ice storage bin if:

1. An extended power failure (one hour or longer) causes ice
cubes in the ice storage bin to melt and freeze together
and jam the dispenser mechanism.

2. The ice dispenser is not used frequently. Ice cubes will
freeze together in the bin and jam the dispenser
mechanism. Remove the ice storage bin and shake to
loosen the cubes.

CAUTION CAUTION

CAUTION

CAUTION CAUTION

NEVER use an ice
pick or similar sharp
instrument to break
up the ice. This could
damage the ice
storage bin and
dispenser
mechanism.

WARNING WARNING

WARNING

WARNING WARNING

Do not use the ice chute as a
handle when removing or
replacing the ice storage bin.
Surfaces there may be
sharp.

Do not put fingers up ice chute.
Surfaces there may be sharp.

13

AUTOMATIC ICE AND WATER DISPENSER

PURESOURCE TM * ICE AND WATER FILTER (SOME
MODELS)

System Startup:

Water supply does not need to be turned off, however, do not
use ice and water dispenser while installing filter. The filter
cartridge has already been installed in the filter housing at the
factory. Refer to the
properly fill the system with water.

NOTENOTE

NOTE

NOTENOTE

If you purchased a refrigerator with a
Ice and Water filter, please read the following use and
care information. This ice and water filter system filters

water to your ice maker and water dispenser. It is located
in the upper right back corner of the fresh food
compartment.

Order new filter
cartridges through the
dealer where you bought
the refrigerator, contact
the

Consumer

Assistance Center

800-944-9044, or go to
our web site at
www.frigidaire.com. It
might be good to order
some filter cartridges
when you first install your
refrigerator. Be sure to
ask for

the

RG-100

How The Water Dispenser Works

PureSource

at 1-

section to

TM

*

PureSource™*

replacement cartridge.

The

PureSource™

Filter System with the RG-100 cartridge is tested
and certified by NSF International, the nationally
recognized and respected, not for profit,
certification organization for public health safety.

The

PureSource™*

Standard 42. See performance data sheet for specifications.
This system should not be used on water that is
microbiologically unsafe or with water of unknown quality
unless the water has been adequately disinfected before or
after traveling through the filtration system.

• Rated Capacity - 400 gallons

• Rated service flow - .5 GPM

• Maximum Rated Pressure - 100 PSI

• Maximum Operating Temp. - 100° F

system is tested and certified to ANSI/NSF

* NGRG-2000 Ice and Water

Changing the Filter:

Water conditions vary throughout the world, but changing the
water filter every 6 - 9 months normally will ensure the highest
possible water quality. The Filter Status light will turn red after
400 gallons of water has flowed through the ice and water
dispenser (some models). Also, if the filter has been in a
refrigerator that has not been in use for awhile (during moving
for example), change the filter before reinstalling the refrigerator.

* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter.

The dispenser system will also operate without filtration (with
filter cartridge removed).

To change filter:

It is not necessary to turn the water supply off to change the filter.

1. Open freezer door and leave open until filter change is
complete.

2. Set ice maker wire signal arm to the OFF (up) position (side
mounted) or the ice maker’s On/Off power switch turned Off-set
to the “O” position (rear mounted) .

3. Hold filter cup firmly, and unscrew towards left (Some water
could leak out as you remove cup. This is normal.). Filter
cartridge should come down with cup. If cartridge remains in
housing, pull down gently, while twisting filter back and forth.

4. Rinse out cup under running water.

5. The large o-ring that seals the filter system sets in the o-ring
groove down inside the cup. Should the o-ring fall out during
filter cartridge replacement, simply place it back in the groove
prior to screwing the cup back in place. If the o-ring becomes
damaged, you will need to order one from the

Assistance Center

6. Discard old filter cartridge.

7. Remove new filter cartridge from packaging. Place in cup. The
end with the small o-ring should be up, out of the cup.

8. Screw cup, with filter, back onto housing. Do Not Use Wrench
To Reinstall Cup. Filter cartridge will self-align as cup is
tightened. Be sure cup is completely tightened with

PureSource™

9. Set ice maker wire signal arm to the ON (down) position (side
mounted) or the ice maker’s On/Off power switch is turned
On-set to the “I” position. (rear mounted).

10. Check for leaks. Open refrigerator door. Wipe any water droplets
from the filter cup. Fill a glass with water. If there is a leak,
unscrew filter cup, and reinsert the filter cartridge. Check
placement of large O-ring. Reinstall filter cup, making certain it is
tightened completely.

11. To condition filter system and purge air from water line, fill a
glass with water. Continue flushing the system for approximately
3 minutes to assure that the purest water possible is stored in
the water tank.

IMPORIMPOR

IMPOR

IMPORIMPOR

TT

ANTANT

T

ANT

TT

ANTANT

.

logo facing outward. Do Not Tighten Past Stop.

Resetting The Filter Status Light (some models)

After replacing the filter cartridge, it will be necessary to
press the
water dispenser. This will reset the Filter Status light. Push
the reset button until the green, red and amber lights flash
(10-15 seconds). Please refer to the complete dispenser
operating instructions attached to the inside of the freezer
door.

On models without a

set of Reminder Stickers included in the envelope that the
Use & Care Manual came in. Choose a dated sticker that
indicates 6 - 9 months (depending on your water quality
and usage) from the date of installation. Place the sticker
on the front of the filter cup to remind you when it is time to
change the filter.

Filter Status

reset button located on the ice and

Filter Status

14

Consumer

reset button, there is a

AUTOMATIC ICE AND WATER DISPENSER

PURESOURCE2
(SOME MODELS)

NOTENOTE

NOTE

NOTENOTE

TM

* ICE AND WATER FRONT FILTER

filter before reinstalling the refrigerator. The dispenser system
will also operate without filtration (with filter cartridge removed
and bypass installed).

To change filter:

If you purchased a refrigerator with a
Ice and Water front filter, please read the following use
and care information. This ice and water filter system

filters water to your ice maker and water dispenser. It is
located in the upper right front corner of the fresh food
compartment.

PureSource2

TM *

System Startup:

Water supply does not need to be turned off, however, do not
use ice and water dispenser while installing filter.

The filter cartridge has already been installed in the filter
housing at the factory. Refer to the

section to properly fill the system with water.

Works

Order new filter
cartridges through the
dealer where you
bought the refrigerator,
contact the

Assistance Center

800-944-9044, or go to
our web site at
www.frigidaire.com. It
might be good to order
some filter cartridges
when you first install
your refrigerator. Be
sure to ask for
100
replacement cartridge.

organization for public health safety. The
Filter system is tested and certified to ANSI/NSF Standards
42 and 53. See performance data sheet for specifications.
This system should not be used on water that is
microbiologically unsafe or with water of unknown quality
unless the water has been adequately disinfected before or
after traveling through the filtration system.

• Rated Capacity - 400 gallons

• Rated service flow - .5 GPM

• Maximum Rated Pressure - 100 PSI

• Maximum Operating Temp. - 100° F

Consumer

the

PureSource™*

The
System NGFC 2000 with the
cartridge FC 100 is tested and certified by
NSF International, the nationally recognized
and respected, not for profit, certification

at 1-

FC-

PureSource2

How The Water Dispenser

TM*

Ice and Water Filter

PureSource2

PureSource2

TM*

TM*

Changing the Filter:

Water conditions vary throughout the world, but changing the
water filter every
6 - 9 months normally will ensure the highest possible water
quality. The Filter Status light will turn red after approximately
400 gallons of water has flowed through the ice and water
dispenser. Also, if the filter has been in a refrigerator that has not
been in use for awhile (during moving for example), change the

* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter.

It is not necessary to turn the water supply off to change the
filter.

1. Set ice maker wire signal arm to the OFF (up) position (side
mounted) or the ice maker’s On/Off power switch turned Off-set
to the “O” position (rear mounted) .

2. Push the
filter cartridge, to release the filter from the housing. To
minimize the possibility of the filter falling out of the
housing during removal, it would be best to hold the
filter as it moves out toward you.

NOTENOTE

NOTE

NOTENOTE

A small amount of water may be released during this
operation. You should have a paper towel or dish cloth
handy to wipe up any water that may drip out of the filter or
housing. Two small holes near the back of the housing
have been added for any excess water to escape. It would
be best to clear away any food near this area on the top
shelf in advance of removing the filter.

3. Pull the old filter cartridge straight out of the housing.

4. Discard the old filter.

5. Remove the new filter cartridge from the packaging and
insert into the filter housing the same way the old one
came out.

6. When the cartridge is almost in, you will feel it stop against
the clip assembly in the back of the housing. The clip
assembly holds the filter cartridge firmly in place. At this
point, you will need to push firmly until the cartridge
snaps fully in place. When completely in place, the front of
the filter cartridge will be flush with the front of the housing.

7. Set ice maker wire signal arm to the ON (down) position (side
mounted) or the ice maker’s On/Off power switch is turned On­set to the “I” position. (rear mounted).

8. Fill a glass with water. As you are doing this, check for
leaks at the filter housing. There will be noticable spurts
and sputters as the system pushes the air out through the
system and out the dispenser nozzle. This is normal.

9. After you have run one glass of water, continue to flush the
system for approximately 3 minutes to assure that the
purest water possible is stored in the water storage tank.

IMPORIMPOR

IMPOR

IMPORIMPOR

Filter Release Button

TT

ANTANT

T

ANT

TT

ANTANT

Resetting The Filter Status Light (some models)

After replacing the filter cartridge, it will be necessary to
press the
dispenser. This will reset the Filter Status light. Push the
reset button until the green, red and amber lights flash (10­15 seconds). Please refer to the complete dispenser
operating instructions attached to the inside of the freezer
door.

15

Filter Reset

button located on the ice and water

, located to the right of the

FOOD STORAGE & ENERGY SAVING IDEAS

FOOD STORAGE IDEAS

Fresh Food Storage

• The fresh food compartment should be kept between 34°
F and 40° F with an optimum temperature of 37° F.

• Avoid overcrowding the refrigerator shelves. This reduces
the circulation of air around the food and results in uneven
cooling.

Fruits and Vegetables

• Storage in the crisper drawers traps moisture to help
preserve the fruit and vegetable quality for longer time
periods.

Meat

• Raw meat and poultry should be wrapped securely so
leakage and contamination of other foods or surfaces
does not occur.

Frozen Food Storage

• The freezer compartment should be kept at 0° F or lower.

• A freezer operates most efficiently when it is at least 2/3
full.

Packaging Foods for Freezing

• To minimize dehydration and quality deterioration, use
aluminum foil, freezer wrap, freezer bags or airtight
containers. Force as much air out of the packages as
possible and seal them tightly. Trapped air can cause food
to dry out, change color, and develop an off-flavor (freezer
burn).

• Wrap fresh meats and poultry with suitable freezer wrap
prior to freezing.

• Do not refreeze meat that has completely thawed.

Loading the Freezer

• Avoid adding too much warm food to the freezer at one
time. This overloads the freezer, slows the rate of freezing,
and can raise the temperature of frozen foods.

• Leave a space between the packages, so cold air can
circulate freely, allowing food to freeze as quickly as
possible.

• Avoid storing hard-to-freeze foods such as ice cream and
orange juice on the freezer door shelves. These foods are
best stored in the freezer interior where the temperature
varies less.

ENERGY SAVING IDEAS

• Locate the refrigerator in the coolest
part of the room, out of direct sunlight,
and away from heating ducts or
registers. Do not place the refrigerator
next to heat-producing appliances such
as a range, oven, or dishwasher. If this

is not possible, a section of cabinetry or an added layer of
insulation between the two appliances will help the refrigerator
operate more efficiently.

• Level the refrigerator so that the doors close tightly.

• Refer to this Use & Care Manual for the suggested
temperature control settings.

• Periodic cleaning of the condenser will help the
refrigerator run more efficiently. See the

Cleaning Chart

• Do not overcrowd the refrigerator or block cold air vents.
Doing so causes the refrigerator to run longer and use
more energy.

• Cover foods and wipe containers dry before placing them
in the refrigerator. This cuts down on moisture build-up
inside the unit.

• Organize the refrigerator to reduce door openings.
Remove as many items as needed at one time and close
the door as soon as possible.

on page 18.

Care and

16

NORMAL OPERATING SOUNDS & SIGHTS

UNDERSTANDING THE SOUNDS YOU MAY HEAR

Your new high-efficiency refrigerator may make unfamiliar
sounds. These are all normal sounds and soon will become
familiar to you. They also indicate your refrigerator is operating
as designed. Hard surfaces, such as vinyl or wood floors,
walls, and kitchen cabinets may make sounds more
noticeable. Listed below are descriptions of some of the most
common sounds you may hear, and what is causing them.

NOTENOTE

NOTE

NOTENOTE

Rigid foam insulation is very energy efficient, but is not a
sound insulator.

A. Evaporator

The flow of refrigerant through the evaporator may
create a boiling or gurgling sound.

B. Evaporator Fan

You may hear air being forced through the refrigerator
by the evaporator fan.

C. Defrost Heater

During defrost cycles, water dripping onto the defrost
heater may cause a hissing or sizzling sound. After
defrosting, a popping sound may occur.

IMPORIMPOR

IMPOR

IMPORIMPOR

During the automatic defrost cycle, you may notice a red
glow in the vents on the back wall of your freezer
compartment. This is normal during the defrost cycle.

TT

ANTANT

T

ANT

TT

ANTANT

D. Automatic Ice Maker

If your refrigerator is equipped with an automatic ice
maker, you will hear ice cubes falling into the ice bin.

E. Cold Control & Automatic Defrost Control

These parts can produce a snapping or clicking sound
when turning the refrigerator on and off.

F. Condenser Fan

You may hear air being forced through the condenser
by the condenser fan.

G. Compressor

Modern, high-efficiency compressors operate much
faster than older models. The compressor may have a
high-pitched hum or pulsating sound.

H. Water Valve

If your refrigerator is equipped with an automatic ice
maker, you will hear a buzzing sound as the water
valve opens to fill the ice maker during each cycle.

IMPORIMPOR

IMPOR

IMPORIMPOR

Your ice maker is shipped with the wire signal arm in the
ON position. To ensure proper function of your ice maker,
hook up water supply immediately or turn ice maker OFF
by lifting the wire signal arm until it clicks or locks in the UP
position.

TT

ANTANT

T

ANT

TT

ANTANT

I. Drain Pan (not removable)

You may hear water running into the drain pan during
the defrost cycle.

J. Condenser

May create minimal sounds from forced air.

17

CARE & CLEANING

18

CARE & CLEANING (CONTINUED)

CAUTION CAUTION

CAUTION

CAUTION CAUTION

Wear gloves when replacing light bulbs to avoid getting
cut.

REPLACING LIGHT BULBS

1. Unplug refrigerator.

2. Wear gloves as protection against possible broken glass.

3. Remove light cover, if necessary.

4. Unscrew and replace old bulb with an appliance bulb of
the same wattage.

5. Replace light cover, if necessary.

6. Remember to plug the refrigerator back in.

Refrigerator Light Replacement

Short
Vacations

Long
Vacations

Light Socket
Located Behind
Left Rear
of Crispers

Crisper Light
Cover

or

Light Bulb

Freezer Light ReplacementCrisper Light Replacement (Models may vary)

Vacation and Moving Tips

• Leave refrigerator operating during vacations of 3 weeks or less.

• Use all perishable items from refrigerator compartment.

• Turn automatic ice maker off, even if you will only be gone for a few days.

• Remove all food and ice if you will be gone one month or more.

• Turn controls to "O" ( the OFF position) and disconnect power.

• Turn off automatic ice maker and turn water supply valve to closed position.

• Clean interior thoroughly.

• Leave both doors open to prevent odors and mold build-up. Block doors open if

necessary.

• Remove all food and ice.

Moving

IMPORIMPOR

IMPOR

IMPORIMPOR

If the refrigerator is going to be stored or moved in freezing temperatures, the water in the ice and water
system must be drained completely. Failure to do so could result in water leaks when the refrigerator is put
back into service. Contact a service representative to perform this operation.

TT

ANTANT

T

ANT

TT

ANTANT

• If using handcart, load from side.

• Adjust rollers all the way up to protect them during sliding or moving.

• Pad cabinet to avoid scratching surface.

19

Major Appliance Warranty Information

Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to
be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.

Exclusions

This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased "as-is" are not covered by this warranty.

5. Food loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.

10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.

If You Need
Service

This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada
Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and
parts under this warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.

USA

1.800.944.9044

Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.

Canada

1.800.668.4606

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4

20

BEFORE YOU CALL

1-800-944-9044 (United States)

1-800-265-8352 (Canada)

Visit our web site at

www.frigidaire.com.

PROBLEM CAUSE CORRECTION

RUNNING OF REFRIGERATOR

Compressor does not run.

Refrigerator runs too
much or too long.

Compressor goes off and
on frequently.

TEMPERATURES ARE TOO COLD

Freezer temperature too
cold. Refrigerator
temperature is satisfactory.

Refrigerator temperature
too cold. Freezer
temperature is satisfactory.

Food stored in drawers
freezes.

Food stored in Meat
Keeper freezes (some
models).

• Freezer control is set to "O".

• Refrigerator is in defrost cycle.

• Plug at wall outlet is

disconnected.

• House fuse blown or tripped
circuit breaker.

• Power outage.

• Room or outside weather is

hot.

• Refrigerator has recently been
disconnected for a period of
time.

• Automatic ice maker is
operating.

• Doors are opened too
frequently or too long.

• Refrigerator/freezer door may
be slightly open.

• Freezer control is set too cold
(control found in refrigerator
section).

• Refrigerator/freezer gasket is
dirty, worn, cracked, or poorly
fitted.

• Condenser is dirty.

• Thermostat keeps the

refrigerator at a constant
temperature.

• Freezer control is set too cold. • Set freezer control to a warmer setting. Allow 24 hours

• Refrigerator control is set too

cold.

• Refrigerator control is set too
cold.

• Meat Keeper Temperature
Control set too cold.

• Set freezer control. See Temperature Controls section.

• This is normal for a fully automatic defrost refrigerator.

The defrost cycle occurs periodically, lasting about 30
minutes.

• Ensure plug is tightly pushed into outlet.

• Check/replace fuse with a 15 amp time-delay fuse.

Reset circuit breaker.

• Check house lights. Call local Electric Company.

• It’s normal for the refrigerator to work longer under

these conditions.

• It takes 8-12 hours for the refrigerator to cool down
completely.

• Ice maker operation causes refrigerator to run slightly
more.

• Warm air entering the refrigerator causes it to run
more. Open doors less often.

• Ensure refrigerator is level. Keep food and containers
from blocking door. See PROBLEM section
OPENING/CLOSING OF DOORS/DRAWERS.

• Set refrigerator control to warmer setting until
refrigerator temperature is satisfactory. Allow 24 hours
for temperature to stabilize.

• Clean or change gasket. Leaks in door seal will cause
refrigerator to run longer in order to maintain desired
temperatures.

• Clean condenser. See
and Cleaning section.

• This is normal. Refrigerator goes on and off to keep
temperature constant.

for temperature to stabilize.

• Set refrigerator control to a warmer setting. Allow 24
hours for temperature to stabilize.

• See solution above.

• Adjust Meat Keeper Temperature Control to a lower

setting. (Meat should be stored at a temperature just
below the freezing point for maximum fresh storage
time. It is normal for ice crystals to form due to the
moisture content of meat.)

Care & Cleaning Chart

in Care

21

BEFORE YOU CALL (CONTINUED)

PROBLEM CAUSE CORRECTION

TEMPERATURES ARE TOO WARM

Freezer/Refrigerator
temperature is too warm.

Freezer temperature is too
warm. Refrigerator
temperature is satisfactory.

Refrigerator temperature is
too warm. Freezer
temperature is satisfactory.

Temperature in the Meat
Keeper is too warm (some
models).

• Doors are opened too
frequently or too long.

• Door is slightly open.

• Condenser is dirty.

• Freezer control is set too

warm.

• Refrigerator control is set too
warm.

• Meat Keeper Temperature
Control is set too warm.

WATER/MOISTURE/FROST INSIDE REFRIGERATOR

Moisture collects on inside
of refrigerator walls.

• Weather is hot and humid.

• Door is slightly open.

• Door is opened too often or too

long.

• Open containers.

• Warm air enters the refrigerator whenever the door is

opened. Open the door less often.

• See PROBLEM section OPENING/CLOSING OF
DOORS/DRAWERS.

• Clean condenser. See

and Cleaning section

• Set freezer control to a colder setting. Allow 24 hours
for temperature to stabilize.

• Set refrigerator control to a colder setting. Allow 24
hours for temperature to stabilize.

• Adjust Meat Keeper Temperature Control to a colder
setting.

• The rate of frost buildup and internal sweating
increases.

• See PROBLEM section OPENING/CLOSING OF
DOORS/DRAWERS.

• Open door less often.

• Keep containers covered.

Care & Cleaning Chart

.

in Care

Water collects on bottom
side of drawer cover.

Water collects in bottom of
drawer.

• Vegetables contain and give
off moisture.

• Washed vegetables and fruit
drain while in the drawer.

WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR

Moisture collects on
outside of refrigerator or
between doors.

• Weather is humid.

• Door is slightly open, causing

cold air from inside refrigerator
to meet warm air from outside.

AUTOMATIC ICE MAKER

Ice maker is not making
any ice.

• Ice maker wire signal arm is in
the “up” or OFF position.

• Household water line valve is
not open.

• Freezer is not cold enough.

• Saddle valve on cold water

pipe is clogged or restricted by
foreign material.

• Check to see if the water
dispenser is dispensing water.

• It is not unusual to have moisture on the bottom side of
the cover.

• Move humidity control (some models) to lower setting.

• Dry items before putting them in the drawer. Water

collecting in bottom of drawer is normal.

• This is normal in humid weather. When humidity is
lower, the moisture should disappear.

• See PROBLEM section OPENING/CLOSING OF
DOORS/DRAWERS.

• Move wire signal arm to the “down” or ON position.

• Turn on household water line valve.

• See PROBLEM section TEMPERATURES ARE TOO

WARM.

• Turn off household water line valve. Remove valve.
Ensure that valve is not a self-piercing saddle valve.
Clean valve. Replace valve if necessary.

• If not, the ice & water filter cartridge is clogged or
restricted by foreign material, and must be replaced.

22

BEFORE YOU CALL (CONTINUED)

PROBLEM CAUSE CORRECTION

AUTOMATIC ICE MAKER (CONTINUED)

Ice maker is not
making enough ice.

Ice maker will not stop
making ice.

Ice maker is not
separating the ice
cubes.

Ice has bad odor and
taste.

• Ice maker is producing less ice
than you expect.

• Freezer is not cold enough.

• Household water line valve is

not completely open.

• Check to see if water
dispenser is dispensing slower
than normal.

• Ice maker wire signal arm is
being held down by some item
in the freezer.

• Ice cubes are not being used
frequently enough.

• Ice cubes are hollow or smaller
than normal.

• Ice has picked up odor or
flavor from strong food stored
in refrigerator or freezer.

• Water running to ice maker
has poor taste or odor.

• Ice not used frequently enough.

• Ice maker should produce approximately 4 – 5 pounds

of ice every 24 hours.
pounds of ice every 24 hours.

• See PROBLEM section TEMPERATURES ARE TOO
WARM.

• Turn on household water line valve.

• If it is, replace the ice & water filter cartridge.

• Move item and release wire signal arm. Remove any

ice cubes that are frozen together over the wire signal
arm.

• Remove and shake ice container to separate cubes.

• The ice & water filter cartridge may be clogged.

Replace filter cartridge.

• Cover foods tightly. Discard stale ice. Ice maker will
produce fresh supply.

• Add filter to water supply line. Consult a water
purifying company.

• Discard stale ice.

Extra Ice

should produce up to 8

ICE DISPENSER

Dispenser will not
dispense ice.

Ice dispenser is
jammed.

• Ice storage container is empty.

• Freezer temperature is set too

warm.

• Household water line valve is
not open.

• Freezer door is not closed.

• Ice dispensing arm has been

held in for more than 4-5
minutes.

• Ice has melted and frozen
around auger due to infrequent
use, temperature fluctuations,
and/or power outages.

• Ice cubes are jammed
between ice maker and back
of ice container.

• Ice cubes are frozen together.

• Ice cubes are hollow or smaller

than normal.

• When the first supply of ice is dropped into the
container, the dispenser should operate.

• Turn freezer control to a higher setting so that ice
cubes will be made. When first supply of ice is made,
dispenser should operate.

• Open household water line valve. Allow sufficient time
for the ice to be made. When ice is made, the
dispenser should operate.

• Ensure freezer door is closed.

• Motor is overloaded. Motor overload protector will

reset in approximately 3 minutes. Ice can then be
dispensed.

• Remove ice container, thaw, and empty the contents.
Clean container, wipe dry, and replace in proper
position. When new ice is made, dispenser should
operate.

• Remove ice cubes that are jamming the dispenser.

• Use the dispenser often so that cubes do not freeze

together.

• The ice & water filter cartridge could be clogged.
Replace the filter cartridge. Dispensing system
operates best at 30 – 100 psi water pressure. Well
water pressures should fall within this range.

23

BEFORE YOU CALL (CONTINUED)

PROBLEM CAUSE CORRECTION

WATER DISPENSER

Dispenser will not
dispense water.

Water has an odd taste
and/or odor.

Water pressure is
extremely low.

ODORS IN REFRIGERATOR

Interior is dirty.

• Household water line valve is
not open.

• Freezer door is not closed.

• Ice & water filter cartridge is

clogged.

• Front filter not fully installed, if
equipped

• Water has been in the tank for
a period of time.

• Unit not properly connected to
cold water line.

• Tubing used in the household
water supply and installation
may affect water taste and
odor.

• Water has a high mineral
content.

• Cut-off and cut-on pressures
are too low (well systems
only).

• Reverse osmosis system is in
regenerative phase.

• Interior needs to be cleaned.

• Food with strong odors is in

refrigerator.

• Open household water line valve. See PROBLEM
section ICE MAKER IS NOT MAKING ANY ICE.

• Ensure that freezer door is closed.

• Replace filter cartridge.

• Push filter in until you hear a “click”. Filter should be

flush with cabinet.

• Draw and discard 10 – 12 glasses of water to freshen
the supply and completely rinse out the tank.

• Connect unit to cold water line that supplies water to
the kitchen faucet.

• For best results, use copper tubing for water
connections.

• Contact water treatment plant for help.

• Have someone turn up the cut-off and cut-on pressure

on the water pump system (well systems only).

• It is normal for a reverse osmosis system to be below
20 psi during the regenerative phase.

• See

• Cover food tightly.

Care & Cleaning Chart

section.

in Care and Cleaning

OPENING/CLOSING OF DOORS/DRAWERS

Door(s) will not close.

Drawers are difficult to
move.

• Door was closed too hard,
causing other door to open
slightly.

• Refrigerator is not level. It
rocks on the floor when moved
slightly.

• Refrigerator is touching a wall
or cabinet.

• Food is touching shelf on top
of drawer.

• Track that drawers slide on is
dirty.

LIGHT BULB IS NOT ON

Light bulb is not on.

• Light bulb is burned out.

• Light switch is stuck.

• No electric current is reaching

refrigerator.

• Close both doors gently.

• Ensure floor is level and solid, and can adequately

support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.

• Ensure floor is level and solid, and can adequately
support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.

• Keep less food in drawer.

• Clean drawer, rollers, and track. See

in Care and Cleaning section.

Chart

• See

• Light switch is located on side of refrigerator and

• See PROBLEM section RUNNING OF

Replacing Light Bulbs

section.

freezer liners.

REFRIGERATOR.

in Care and Cleaning

Care & Cleaning

24