Frigidaire 241553001 User Manual

P/N 241553001 (0804)

Welcome & Congratulations

Congratulations on your purchase of a new refrigerator! We
here at Electrolux Home Products are very proud of our
product and we are completely committed to providing you
with the best service possible. Your satisfaction is our #1
priority.

Please read this Use & Care Manual very carefully. It contains
valuable information on how to properly maintain your new
refrigerator.

We know you’ll enjoy your new refrigerator and Thank You
for choosing our product. We hope you consider us for future
purchases.

PLEASE READ AND SAVE THESE INSTRUCTIONS

This Use & Care Manual provides specific operating
instructions for your model. Use your refrigerator only as
instructed in this manual. These instructions are not meant
to cover every possible condition and situation that may
occur. Common sense and caution must be practiced when
installing, operating and maintaining any appliance.

Please record your model and serial numbers below for
future reference. This information is found on the serial
plate located inside the refrigerator compartment.

Questions?

1-800-944-9044

(United States)

1-866-213-9397

(Canada)

or visit our web site at www.frigidaire.com

Extend Your Warranty Protection

With An

Extended Service Contract

CALL 1-800-944-9044

To Enjoy These Benefits:

• Total freedom from repair bills so

unexpected repairs won’t upset your
budget.

NOTE: Use only soap and water to clean serial plate.

Model Number:

Serial Number:

Purchase Date:

• Fast, convenient toll-free service is just
a phone call away.

• Top-quality repairs by factory-trained
experts.

• Quick access to genuine replacement
parts so you can rest assured your

refrigerator is repaired with the proper
components.

Please attach sales receipt

here for future reference.

Please complete and mail in the

Registration Card

included with your

refrigerator.

Product

2

Important Safety Instructions

Please Read All Instructions Before Using This Refrigerator.

FOR YOUR SAFETY

• Do not store or use gasoline, or other flammable liquids
in the vicinity of this or any other appliance. Read
product labels for warnings regarding flammability and
other hazards.

• Do not operate the refrigerator in the presence of
explosive fumes.

• Avoid contact with any moving parts of automatic ice
maker.

• Remove all staples from the carton. Staples can cause
severe cuts, and also destroy finishes if they come in
contact with other appliances or furniture.

CHILD SAFETY

Destroy or recycle the carton, plastic bags, and any exterior
wrapping material immediately after the refrigerator is
unpacked. Children should NEVER use these items to play
with. Cartons covered with rugs, bedspreads, plastic sheets
or stretch wrap may become airtight chambers, and can
quickly cause suffocation.

These Guidelines Must Be Followed To Ensure That Safety Mechanisms In This Refrigerator
Will Operate Properly.

PROPER DISPOSAL OF YOUR REFRIGERATOR
OR FREEZER

Risk of child entrapment

Child entrapment and suffocation
are not problems of the past.
Junked or abandoned refrigerators
or freezers are still dangerous –
even if they will sit for “just a few
days.” If you are getting rid of your
old refrigerator or freezer, please
follow the instructions below to
help prevent accidents.

Before you throw away your old refrigerator/ freezer:

• Remove doors.

• Leave shelves in place so children may not easily climb
inside.

• Have refrigerant removed by a qualified service
technician.

ELECTRICAL INFORMATION

• The refrigerator must be plugged into its own
dedicated 115 Volt, 60 Hz., AC only electric outlet.

The power cord of the appliance is equipped with a
three-prong grounding plug for your protection against
electrical shock hazards. It must be plugged directly
into a properly grounded three-prong receptacle. The
receptacle must be installed in accordance with local
codes and ordinances. Consult a qualified electrician.

Do not use an extension cord or adapter plug.

• If the power cord is damaged, it should be replaced by the
manufacturer, service technician or a qualified person to
prevent any risk.

• Never unplug the refrigerator by pulling on the power
cord. Always grip the plug firmly, and pull straight out
from the receptacle to prevent damaging the power cord.

• Unplug the refrigerator before cleaning and before
replacing a light bulb to avoid electrical shock.

• Performance may be affected if the voltage varies by
10% or more. Operating the refrigerator with insufficient
power can damage the compressor. Such damage is
not covered under your warranty.

• Do not plug the unit into an outlet controlled by a wall
switch or pull cord to prevent the refrigerator from being
turned off accidentally.

• Avoid connecting refrigerator to a Ground Fault Interruptor
(GFI) circuit.

3

Installation

This Owner’s Guide provides specific operating instructions
for your model. Use the refrigerator only as instructed in this
Use & Care Manual. Before starting the refrigerator, follow

these important first steps.

LOCATION

• Choose a place that is near a grounded electrical outlet.
Do Not use an extension cord or an adapter plug.

• If possible, place the refrigerator out of direct sunlight
and away from the range, dishwasher or other heat
sources.

• The refrigerator must be installed on a floor that is level
and strong enough to support a fully loaded refrigerator.

• Consider water supply availability for models equipped
with an automatic ice maker.

INSTALLATION

Do Not install the refrigerator where

the temperature will drop below 55°F (13°C) or rise
above 110°F (43°C). The compressor will not be able
to maintain proper temperatures inside the
refrigerator.

Do Not block the toe grille on the
lower front of your refrigerator. Sufficient air circulation
is essential for the proper operation of your
refrigerator.

Installation Clearances

• Allow the following clearances for ease of installation,
proper air circulation, and plumbing and electrical
connections:

Sides & Top --------------- 3/8”
Back ------------------------ 1”

DOOR OPENING

NOTE: If your refrigerator is placed with the door hinge

side against a wall, you may have to allow additional
space so the door can be opened wider.

Your refrigerator should be positioned to allow easy access to
a counter when removing food. For best use of drawers and
freezer baskets, the refrigerator should be in a position where
both the refrigerator and freezer doors can be fully opened.

TOE GRILLE INSTALLATION / REMOVAL

To Remove Toe Grille:

1. Open freezer and fresh food compartment doors.

2. Working from left side of toe grille, slip your fingers
between top of toe grille and cabinet. Gently pull
forward until first set of tabs are free. Slide your hand
down past the free tabs and pull forward again until the
second set of tabs are free. Continue this process until
all tabs are free and the toe grille can be removed. (See
graphic at top of page in right column.)

To Install Toe Grille:

1. Open freezer and
fresh food
compartment doors.

2. Line up toe grille at
base of refrigerator,
making sure the four
bottom tabs are
resting through holes
at base of cabinet.

3. Starting from left side
of toe grille, press in on first top tab using your thumb
and push toe grille forward until it snaps in place. Continue
this process until all tabs aresnapped in place and toe
grille is secured to refrigerator.

LEVELING

All four corners of your refrigerator must rest firmly on a solid floor.
Your refrigerator is equipped with adjustable front rollers to help
level your unit. To ensure proper door seal and assist door closing,
the refrigerator should be tilted 1/4” (6 mm), front to back.

To Level Your Refrigerator:

1. Remove toe grille. (See

2. Use flat-blade screwdriver or 3/8” socket wrench to adjust
front rollers.

NOTE: The refrigerator doors are designed to shut by
themselves within a 20 degree opening.

3. Check both doors to be sure seals touch cabinet on all four
sides.

“To Remove Toe Grille”

.)

4

Installation

To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator

from electrical power before connecting a water supply line to the refrigerator.

To Avoid Property Damage:

• Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not
recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible
for any damage if plastic tubing is used for supply line.

• DO NOT install water supply tubing in areas where temperatures fall below freezing.

• Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft
water, ensure that the softener is maintained and working properly.

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

Before Installing The Water Supply Line, You Will Need

• Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver

• Access to a household cold water line with water pressure between 20 and 100 psi.

• A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed,
you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water
pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

• A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type
shutoff valve.

• A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

- Connecting Ice Maker To Water Supply

NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6

meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2)
ferrules/sleeves, and instructions for installing a water supply line.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply
and flush supply line until water is clear. Turn OFF water supply at shut
off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line,
as shown.

5. Push water supply line into water valve inlet as far as it will go (¼ inch).
Slide ferrule (sleeve) into valve inlet and finger tighten compression nut
onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of
refrigerator as shown.

7. Coil excess water supply line (about 2½ turns) behind refrigerator as shown
and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that
leak.

9. Reconnect refrigerator to electrical power source.

10. Make sure ice maker power switch is turned On (See page 14 for location of
power switch).

IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may
cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be
discolored or have poor flavor. Discard ice made during the first 24 hours.

5

Door Removal Instructions

DOOR REMOVAL INSTRUCTIONS:

If it is necessary to move the refrigerator through narrow doorways, follow
these steps to remove the doors.

6

Features At A Glance

Features may vary according to model

7

Temperature Controls

COOL DOWN PERIOD

To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 6 hours before loading it
with food.

REFRIGERATOR & FREEZER CONTROLS

NOTE: When changing control settings, wait 24 hours before making additional adjustments.

After 24 hours, adjust the controls as
needed. Make your adjustments small
and gradual; allowing time for
temperatures to change and stabilize.
Refer to the adjacent guidelines for
temperature settings.

The range of possible settings is 1
through 9, with 9 being the coldest.

Both the Freezer and Fresh Food
compartments are preset at the factory
to 5, the midpoint temperature setting.

To adjust the temperature to a higher or
lower setting, press the Warmer or
Colder button closest to the display. The
first time you press the button, the
display shows the last setting you
entered. Each press of the button after
that increments the setting by one.

The display shows your new setting
momentarily, then changes back to the
current temperature.

IF THE TEMPERATURE
DISPLAYS FLASH...

If ever you see both temperature displays
continously flashing, it may indicate that
the control system has detetcted a
performance problem. Call your Frigidaire
service representative, who can interpret
the flashing message.

Temperature Adjustment Guide

If Fresh Food compartment is too warm

If Fresh Food compartment is too cold

If Freezer compartment is too warm

If Freezer compartment is too cold

Adjust Fresh Food control one number

higher by pressing the Colder button.

Adjust Fresh Food control one number

lower by pressing the Warmer button.

Adjust Freezer control one number higher

by pressing the Colder button.

Adjust Freezer control one number lower

by pressing the Warmer button.

To maintain temperatures, a fan
circulates air in the refrigerator and
freezer compartments. For good
circulation, do not block cold air vents
with food items.

8

Temperature Controls

OTHER CONTROL FEATURES

Cooling System On/Off Button

TURNING THE COOLING SYSTEM ON AND OFF

You can disable the cooling system in your refrigerator by
pressing the On/Off button located on the left side of the
temperature control panel.

NOTE: Each time you make
settings on the control panel,
a single audible tone
acknowledges your input.

To ensure that you do not accidentally turn off the cooling
system, the button does not work unless you press

hold

it for three seconds.

Once you disable the cooling system, all refrigeration to
the freezer and fresh food compartments stops.

To turn the cooling system back on, you must again press

and hold

the On/Off button for three more seconds.

and

IMPORTANT: Pressing the On/Off button on the control
panel disables your refrigerator’s cooling system but does
not disconnect power to lights and other electrical
components. To turn off power to your refrigerator you
must unplug the power cord from the wall outlet.

9

Looking Inside

ICE CREAM SHELF (SOME MODELS)

This shelf attaches to the top of the ice dispenser container. It allows storage
of both round and rectangular cartons of your favorite ice cream.

To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break suddenly if
nicked, scratched, or exposed to sudden temperature change.

CANTILEVER SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted to suit individual needs. Before
adjusting the shelves, remove all food. Cantilever shelves are supported at
the back of the refrigerator.

Ice Cream Shelf

1

To adjust cantilever shelves:

1 Lift front edge up.

2 Pull shelf out.

Replace the shelf by inserting the hooks at rear of the shelf into the wall
bracket. Lower the shelf into the desired slots and lock into position.

* SpillSafeTM

In some models, the
food and for fast cleaning. The shelves slide out independently of their
mounting brackets. Just pull the front of the shelf forward. Shelves can be
extended as far as the stopper will allow but are not removable from their
mounting brackets.

glass shelves (some models) catch and hold accidental spills.

* SpillSafe

TM

shelves slide out for easy access to

2

Cantilever Glass Shelf

1

2

* WhiteWestinghouse - SpillFree

Cantilever Sliding Glass Shelf

TM

10

Looking Inside

(continued)

DOOR STORAGE

Door bins and shelves are provided for convenient storage
of jars, bottles, and cans. Frequently used items can be
quickly selected.

Some models have door bins that can accommodate gallon­sized plastic drink containers and economy-sized jars and
containers. Some bins are adjustable for maximum storage
capacity.

The dairy compartment, which is warmer than the general
food storage section, is intended for short term storage of
cheese, spreads, or butter.

ADJUSTABLE DOOR BINS

Some models have adjustable door bins that can be moved
to suit individual needs.

To move door bins

1. Lift bin straight up.

2. Remove bin.

3. Place bin in desired position.

4. Lower bin onto supports until locked in place.

TALL BOTTLE RETAINER (SOME MODELS)

The Tall Bottle Retainer keeps tall containers in the bin from
falling forward when opening or closing the refrigerator door.
To install, hold the retainer at the top, and slide it over the
outside wall of the bin, as shown in the diagram.

Tall Bottle Retainer

SPECIAL ITEM RACK (SOME MODELS)

The innovative design of the Special Item Rack allows you
to store a six-pack of 12 ounce drink cans, a bottle of wine,
a two-liter soft drink bottle, or a carton of eggs. The Special
Item Rack mounts on the left side of your refrigerator. To
install, just slide the Special Item Rack onto any shelf as
shown in the drawing.

Adjustable Door Bin

Special Item Rack

11

Looking Inside -

Special Storage Areas

CRISPERS (SOME MODELS)

The crispers, located under the bottom refrigerator shelf,
are designed for storing fruits, vegetables, and other fresh
produce. Wash items in clear water and remove excess water
before placing them in the crispers. Items with strong odors
or high moisture content should be wrapped before storing.

Crisper Drawer

MEAT KEEPER

Some models are equipped with a Meat Keeper. Meat Keeper
temperatures can be adjusted by sliding the Meat Keeper
Temperature Control in either direction. Use this pan for short
term storage of bulk meat items. If meats are to be kept
longer than one or two days, they should be frozen. The
Meat Keeper is fixed and cannot be moved up or down. If
fruits or vegetables are to be stored in the Meat Keeper, set
the Meat Keeper Temperature Control to a warmer setting to
prevent freezing.

HUMIDITY CONTROL (SOME MODELS)

The Humidity Control, present on some models with crisper
drawers, allows you to adjust the humidity within the crisper.
This can extend the life of fresh vegetables that keep best
in high humidity.

NOTE: Leafy vegetables keep best when stored with
the Humidity Control set on Higher Humidity, or in a
drawer without a Humidity Control. This keeps incoming
air to a minimum and maintains maximum moisture
content.

Crisper Humidity Control

Meat Keeper with Temperature Control

WINE RACK (SOME MODELS)

The wine rack stores bottles of wine, or single two-liter plastic
bottles of juice or soda pop. To install, slide the Wine Rack
onto the shelf with the curve facing in. To remove, slide the
Wine Rack out. Install on either side of shelf.

Wine Rack

12

Automatic Ice and Water Dispenser

AUTOMATIC ICE & WATER DISPENSER OPERATING INSTRUCTIONS

13

Automatic Ice and Water Dispenser

ICE AND WATER DISPENSER FEATURES

The ice and water dispenser conveniently dispenses chilled water, and ice cubes or crushed ice, depending on the model.
To operate the ice dispenser, select the ice option desired using the touchpad. Press a glass against the dispensing paddle

as far up as possible to catch all ice. To stop dispensing ice, pull glass away from dispensing paddle. Do not remove the
glass until the ice has completely dispensed. (Complete instructions for the dispenser operation are attached to the inside
of the freezer door.)

How the Water Dispenser Works

The water tank, located behind the refrigerator compartment, automatically fills as water is dispensed. For proper dispenser
operation, the recommended supply water pressure should fall between 20 psi and 100 psi.

Water pressure must not exceed 100 lbs. Excessive pressure may cause water filter to malfunction.

After the refrigerator is connected to the water supply, fill the water tank byat90drawing one glass of water. It may take about

Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected

to soft water, ensure that the softener is maintained and working properly.

How the Ice Dispenser Works

The ice maker and container are located in the top of the freezer compartment. After the
refrigerator is installed properly and has cooled for several hours, the ice maker can begin
making ice within 24 hours. Air in new plumbing lines may cause the ice maker to cycle two
or three times before making a full tray of ice. Ice production is controlled by the ice maker’s
On/Off power switch. Press the switch to the “O” position to turn it Off and press it to the “I”
position to turn it On. With no usage it will take approximately 2 days to fill the ice container.
The ice maker also has a built-in wire signal arm,which automatically stops ice production
when the ice bin is full. This signal arm should not be used to manually stop the ice maker.

The ice maker produces 4 to 6 pounds of ice every 24 hours depending on usage conditions.
Ice is produced at a rate of 8 cubes every 75 to 90 minutes.

Because of new plumbing connections, the first production of ice cubes may be discolored or have an odd flavor. These
should be discarded until the cubes made are free of discoloration and taste.

ICE DISPENSER TIPS

• Ice cubes stored too long may develop an odd flavor. Empty the ice container and ensure that the ice maker’s On/Off
power switch is turned On (set to the “I” position). The ice maker will then produce more ice.

• Occasionally shake the ice container to keep ice separated.

• Keep the ice maker’s On/Off power switch turned Off (set to the “O” position) until the refrigerator is connected to the water
supply or whenever the water supply is turned off.

IMPORTANT: The ice maker is turned On at the factory so it can work as soon as you install your refrigerator. If you

cannot connect a water supply, turn the On/Off switch to the Off (“O”) position. Otherwise, the ice maker’s valve
may be noisy when it attempts to operate without water.

If the dispensing paddle is pushed for more than 4 minutes, the dispenser motor may overload
and stop. The overload protector will reset automatically after 3 or 4 minutes.

• If a large quantity of ice is needed at one time, it is best to remove cubes directly from the ice container.

• The following sounds are normal when the ice maker is operating:

• Motor running

• Ice dropping into ice container

• Water valve opening or closing

• Turn Off the ice maker when cleaning the freezer and during vacations.

• If the ice maker will be turned off for a long period of time, you should also turn off the water supply valve.

14

Automatic Ice and Water Dispenser

Do not use the ice chute as a handle when
removing or replacing the ice storage bin.
Surfaces there may be sharp.

Do not put fingers up ice chute. Surfaces
there may be sharp.

CLEANING THE ICE DISPENSER

Clean the dispenser and ice container at regular intervals, particularly
before you take a vacation or move, or if the ice dispenser sticks.

1. Turn off ice production by pressing the ice maker’s On/Off switch.

2. Remove ice container by lifting up and out. Empty and carefully clean
the container with mild detergent. Rinse with clear water. Do not use
harsh or abrasive cleaners. Allow ice container to dry completely before
replacing in the freezer.

3. Remove ice chips and clean the shelf and chute that supports the ice
container.

4. Replace the ice container. Press the ice maker’s On/Off switch to
resume ice production.

IMPORTANT: When removing or replacing the ice bin, do not
rotate the auger in the ice bin. If the auger is accidentally turned,
you must realign the auger by turning it in 90° turns until the ice bin
fits into place with the drive mechanism.

Remove and empty the ice storage bin if:

1. An extended power failure (one hour or longer) causes ice cubes in
the ice storage bin to melt and freeze together and jam the dispenser
mechanism.

2. The ice dispenser is not used frequently. Ice cubes will freeze together
in the bin and jam the dispenser mechanism. Remove the ice storage
bin and shake to loosen the cubes.

NEVER use an ice pick or similar sharp instrument to break up the ice.
This could damage the ice storage bin and dispenser mechanism.

15

Automatic Ice and Water Dispenser

PureSource TM * Ice and Water Filter (some models)

NOTE: If you purchased a refrigerator with a
and care information.

This ice and water filter system filters water to your ice maker and water dispenser. It is

PureSource

located in the upper right back corner of the fresh food compartment.

System Startup:

Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter. The filter
cartridge has already been installed in the filter housing at the factory. Refer to the
to properly fill the system with water.

Changing the Filter:

Water conditions vary throughout the world, but changing the water filter every
6 - 9 months normally will ensure the highest possible water quality. The Filter
Status light will turn red after 400 gallons of water has flowed through the ice
and water dispenser (some models). Also, if the filter has been in a refrigerator
that has not been in use for awhile (during moving for example), change the
filter before reinstalling the refrigerator. The dispenser system will also operate
without filtration (with filter cartridge removed).

To change filter:

It is not necessary to turn the water supply off to change the filter.

1. Open freezer door and leave open until filter change is complete.

2. Turn the ice maker’s power switch to the Off (“O”) position (See illustration
on page 14).

3. Hold filter cup firmly, and unscrew towards left (Some water could
leak out as you remove cup. This is normal.). Filter cartridge should come
down with cup. If cartridge remains in housing, pull down gently, while
twisting filter back and forth.

4. Rinse out cup under running water.

5. The large o-ring that seals the filter system sets in the o-ring groove
down inside the cup. Should the o-ring fall out during filter cartridge

Order new filter cartridges through the
dealer where you bought the refrigerator,
contact the
1-800-944-9044, or go to our web site at
www.frigidaire.com. It might be good to
order some filter cartridges when you first
install your refrigerator. Be sure to ask for

the

RG-100

cartridge.

Customer Care Center

PureSource™*

replacement

at

replacement, simply place it back in the groove prior to screwing the cup
back in place. If the o-ring becomes damaged, you will need to order one
from the

6. Discard old filter cartridge.

7. Remove new filter cartridge from packaging and place in cup. The end
with the small o-ring should be up, out of the cup.

8. Screw cup, with filter, back onto housing. Do Not Use Wrench To Reinstall
Cup. Filter cartridge will self-align as cup is tightened. Be sure cup is
completely tightened with

Tighten Past Stop.

9. Turn the ice maker’s power switch to the On (“I”) position.

10. Check for leaks. Open refrigerator door. Wipe any water droplets from the
filter cup. Fill a glass with water. If there is a leak, unscrew filter cup, and
reinsert the filter cartridge. Check placement of large O-ring. Reinstall
filter cup, making certain it is tightened completely.

11. To condition filter system and purge air from water line, fill a glass with
water. Continue flushing the system for approximately 3 minutes to assure
that the purest water possible is stored in the water tank.

TM

* Ice and Water filter, please read the following use

Customer Care Center

PureSource™

How The Water Dispenser Works

.

logo facing outward. Do Not

section

IMPORTANT: Resetting The Filter Status Light (some models)

After replacing the filter cartridge, it will be necessary to press the

Status

reset button located on the ice and water dispenser. This will reset
the Filter Status light. Push the reset button until the green, red and amber
lights flash (10-15 seconds). Please refer to the complete dispenser
operating instructions attached to the inside of the freezer door.

On models without a

Reminder Stickers included in the envelope that the Use & Care Manual

.947 1 TD0.0245 Tc0.13927Tw(On mo.7(.)-1t indi 0and w)1J1np.

Filter Status

reset button, there is a set of

Filter

16

Automatic Ice and Water Dispenser

PureSource2

NOTE: If you purchased a refrigerator with a

TM

* Ice and Water Front Filter (some models)

PureSource2

TM *

Ice and Water front filter, please read the following

use and care information. This ice and water filter system filters water to your ice maker and water dispenser. It is

located in the upper right front corner of the fresh food compartment.

System Startup:

Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter.

The filter cartridge has already been installed in the filter housing at the factory. Refer to the

Works

section to properly fill the system with water.

How The Water Dispenser

Changing the Filter:

Water conditions vary throughout the world, but changing the water filter every
6 - 9 months normally will ensure the highest possible water quality. The Filter
Status light will turn red after approximately 400 gallons of water has flowed
through the ice and water dispenser. Also, if the filter has been in a refrigerator
that has not been in use for awhile (during moving for example), change the
filter before reinstalling the refrigerator. The dispenser system will also operate
without filtration (with filter cartridge removed and bypass installed).

To change filter:

It is not necessary to turn the water supply off to change the filter.

1. Turn the ice maker’s power switch to the Off (“O”) position (See illustration

on page 14).

2. Push the
to release the filter from the housing. To minimize the possibility of the
filter falling out of the housing during removal, it would be best to hold the

Order new filter cartridges through the
dealer where you bought the refrigerator,
contact the
1-800-944-9044, or go to our web site at
www.frigidaire.com. It might be good to
order some filter cartridges when you first
install your refrigerator. Be sure to ask for

the

FC-100

cartridge.

Customer Care Center

PureSource™*

replacement

at

filter as it moves out toward you.

NOTE: A small amount of water may be released during this operation.
You should have a paper towel or dish cloth handy to wipe up any water
that may drip out of the filter or housing. Two small holes near the back of
the housing have been added for any excess water to escape. It would be
best to clear away any food near this area on the top shelf in advance of
removing the filter.

3. Pull the old filter cartridge straight out of the housing.

4. Discard the old filter.

The

PureSource2

Water Filter System NGFC
2000 with the
cartridge FC 100 is tested and

certified by NSF International,
the nationally recognized and respected,
not for profit, certification organization for
public health safety. The
Filter system is tested and certified to ANSI/
NSF Standards 42 and 53. See
performance data sheet for specifications.
This system should not be used on water
that is microbiologically unsafe or with water
of unknown quality unless the water has
been adequately disinfected before or after
traveling through the filtration system.

• Rated Capacity - 400 gallons

• Rated service flow - .5 GPM

• Maximum Rated Pressure - 100 PSI

• Maximum Operating Temp. - 100° F

* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter.

TM*

Ice and

PureSource2

PureSource2

5. Remove the new filter cartridge from the packaging and insert into the
filter housing the same way the old one came out.

6. When the cartridge is almost in, you will feel it stop against the clip assembly

TM*

in the back of the housing. The clip assembly holds the filter cartridge
firmly in place. At this point, you will need to push firmly until the cartridge
snaps fully in place. When completely in place, the front of the filter cartridge
will be flush with the front of the housing.

7. Turn the ice maker’s power switch to the On (“I”) position.

TM*

8. Fill a glass with water. As you are doing this, check for leaks at the filter
housing. There will be noticeable spurts and sputters as the system pushes
the air out through the system and out the dispenser nozzle. This is normal.

9. After you have run one glass of water, continue to flush the system for
approximately 3 minutes to assure that the purest water possible is stored
in the water storage tank.

IMPORTANT: Resetting The Filter Status Light (some models)

After replacing the filter cartridge, it will be necessary to press the

Reset

Filter Status light. Push the reset button until the green, red and amber
lights flash (10-15 seconds). Please refer to the complete dispenser
operating instructions attached to the inside of the freezer door.

Filter Release Button

, located to the right of the filter cartridge,

button located on the ice and water dispenser. This will reset the

17

Filter

Food Storage & Energy Saving Ideas

FOOD STORAGE IDEAS

Fresh Food Storage

• The fresh food compartment should be kept between 34° F and 40° F with an optimum temperature of 37° F.

• Avoid overcrowding the refrigerator shelves. This reduces the circulation of air around the food and results in uneven
cooling.

Fruits and Vegetables

• Storage in the crisper drawers traps moisture to help preserve the fruit and vegetable quality for longer time periods.

Meat

• Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or surfaces does not
occur.

Frozen Food Storage

• The freezer compartment should be kept at 0° F or lower.

• A freezer operates most efficiently when it is at least 2/3 full.

Packaging Foods for Freezing

• To minimize dehydration and quality deterioration, use aluminum foil, freezer wrap, freezer bags or airtight containers.
Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out,
change color, and develop an off-flavor (freezer burn).

• Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.

• Do not refreeze meat that has completely thawed.

Loading the Freezer

• Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing,
and can raise the temperature of frozen foods.

• Leave a space between the packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.

• Avoid storing hard-to-freeze foods such as ice cream and orange juice on the freezer door shelves. These foods are
best stored in the freezer interior where the temperature varies less.

ENERGY SAVING IDEAS

• Locate the refrigerator in the coolest part of the room, out of direct sunlight,
and away from heating ducts or registers. Do not place the refrigerator
next to heat-producing appliances such as a range, oven, or dishwasher.
If this is not possible, a section of cabinetry or an added layer of insulation
between the two appliances will help the refrigerator operate more
efficiently.

• Level the refrigerator so that the doors close tightly.

• Refer to this Use & Care Manual for the suggested temperature control
settings.

• Do not overcrowd the refrigerator or block cold air vents. Doing so causes
the refrigerator to run longer and use more energy.

• Cover foods and wipe containers dry before placing them in the
refrigerator. This cuts down on moisture build-up inside the unit.

• Organize the refrigerator to reduce door openings. Remove as many
items as needed at one time and close the door as soon as possible.

18

Normal Operating Sounds & Sights

UNDERSTANDING THE SOUNDS YOU MAY HEAR

Your new high-efficiency refrigerator may make unfamiliar
sounds. Most often, these are all normal sounds that soon
become familiar to you. They indicate your refrigerator is
operating as designed. Hard surfaces, such as vinyl or wood
floors, walls, and kitchen cabinets may make sounds more
noticeable. The following list describes some of the most
common sounds you may hear, and what is causing them.

NOTE: Rigid foam insulation is very energy efficient,
but is not a sound insulator.

A. Evaporator

The flow of refrigerant through the evaporator may
create a boiling or gurgling sound.

B. Evaporator Fan

You may hear air being forced through the refrigerator
by the evaporator fan.

C. Defrost Heater

During defrost cycles, water dripping onto the defrost
heater may cause a hissing or sizzling sound. After
defrosting, a popping sound may occur.

IMPORTANT: During the automatic defrost cycle, you
may notice a red glow in the vents on the back wall of
your freezer compartment. This is normal during the
defrost cycle.

19

Care & Cleaning

Keep your refrigerator and freezer clean to prevent odor build-up. Wipe up any spills immediately and clean both sections at
least twice a year. Never use any type of scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any
surface. Do not wash any removable parts in a dishwasher.

outlet before cleaning.

• When moving the refrigerator, pull straight out. Do not shift the refrigerator from side to side as this may
damage the floor. Be careful not to move the refrigerator beyond the plumbing connections.

• Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp hands.

• Never us s CHLORIDE to clean stainless steel.

NOTES:

• If you set your temperature controls to turn off cooling, power to lights and other electrical components continues
until you unplug the power cord from the wall outlet.

• Do not use razor blades or other sharp instruments which can scratch the appliance surface when removing
adhesive labels. Any glue left from tape or labels can be removed with a mixture of warm water and mild
detergent, or, touch the glue residue with the sticky side of tape you have already removed. Do not remove the

serial plate.

Always unplug the electrical power cord from the wall

Care & Cleaning Chart

Part Cleaning Agents Tips and Precautions
Interior/Door
Liner

Door Gaskets

Drawers/Bins

Glass
Shelves

Toe Grille

Exterior and
Handles

Exterior and
Handles
(Stainless
Steel Models
Only)

• Soap and water

• Baking soda and

water

• Soap and water

• Soap and water

• Soap and water

• Glass cleaner

• Mild liquid sprays

• Soap and water

• Mild liquid sprays

• Vacuum attachment

• Soap and water

• Non Abrasive Glass

Cleaner

• Soap and water

• Ammonia

• Stainless Steel

Cleaners

Use 2 tablespoons of baking soda in 1 quart of warm water. Be

sure to wring excess water out of sponge or cloth before
cleaning around controls, light bulb or any electrical part.

Wipe gaskets with a clean soft cloth.

Do not wash any removable items (bins, drawers, etc.) in
dishwasher.

Allow glass to warm to room temperature before immersing in
warm water.

Vacuum dust from front of toe grille. Remove toe grille (See
illustration on page 4). Vacuum backside and wipe with sudsy
cloth or sponge. Rinse and dry.

Do not use commercial household cleaners, ammonia, or alcohol
to clean handles. Use a soft cloth to clean smooth handles. Do

Not use a dry cloth to clean smooth doors.

Never use CHLORIDE to clean stainless steel.

Clean stainless steel front and handles with non-abrasive soapy
water and a dishcloth. Rinse with clean water and a soft cloth.
Wipe stubborn spots with an ammonia-soaked paper towel, and
rinse. Use a non-abrasive stainless steel cleaner. These cleaners
can be purchased at most home improvement or major
department stores. Always follow manufacturer's instruction.

NOTE: Always, clean, wipe and dry with the grain to prevent
cross-grain scratching. Wash the rest of the cabinet with warm

water and mild liquid detergent. Rinse well, and wipe dry with a
clean soft cloth.

20

Care & Cleaning

(continued)

21

Warranty Information

REFRIGERATOR WARRANTY

Your refrigerator is protected by this warranty

FULL ONE-YEAR
WARRANTY

LIMITED 2ND-5TH
YEAR WARRANTY
(Cabinet Liner and
Sealed System)

LIMITED
WARRANTY
(Applicable to the
State of Alaska)

WARRANTY

PERIOD

One year from original
purchase date

Second through fifth
years from original
purchase date

Time periods listed
above.

THROUGH OUR AUTHORIZED SERVICERS,

Pay all costs for repairing or replacin g any part s of this
appliance whic h prove to be defective in materials or
workmanship. Excludes original and replacement Ice
& Water filter cartridges (if equipped). Original and
replacement cartridges are warranted for 30 days
(parts only).

Repair or replace any parts in the cabinet liner or
Sealed Refrigeration System (compressor, condenser,
evaporator, drier and tubing) which prove to be
defective in materials or workmanship.

All of the provisions of the full warranties above and
the exclusions listed below apply.

WE WILL:

THE CONSUMER WILL BE RESPONSIBLE FOR:

Costs of service calls that are listed under

RESPONSIBILITIES OF THE CONSUMER. *

Costs for pick up and delivery of the appliance required because
of service. Costs for labor, parts and transportation other than
with respect to the cabinet liner or Sealed Refrigeration System.

Costs of the technician's travel to the home and any costs for
pick up and delivery of the appliance required because of
service.

NORMAL

In the U.S.A., your appliance is warranted by Electrolux Home Products, Inc. We authorize no person to change or add to any of our
obligations under this warranty. Our obligations for service and parts under this warranty must be performed by us or an authorized
Electrolux Home Products, Inc. servicer. In Canada, your appliance is warranted by Electrolux Canada Corp.

22

1-800-944-9044 (United States)
1-866-213-9397 (Canada)

Before You Call

Visit our web site at
www.frigidaire.com.

PROBLEM CAUSE CORRECTION

RUNNING OF REFRIGERATOR

Compressor does not run.

Refrigerator runs too
much or too long.

Compressor goes off and
on frequently.

Digital temperature
displays are flashing.

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Cooling system is turned Off.

Refrigerator is in defrost cycle.

Plug at wall outlet is
disconnected.
House fuse blown or tripped
circuit breaker.
Power outage.

Room or outside weather is
hot.
Refrigerator has recently been
disconnected for a period of
time.
Automatic ice maker is
operating.
Doors are opened too
frequently or too long.
Refrigerator/freezer door may
be slightly open.

Freezer control is set too cold
(control found in refrigerator
section).
Refrigerator/freezer gasket is
dirty, worn, cracked, or poorly
fitted.

Electronic control system
keeps the refrigerator at a
constant temperature.

Electronic control system has
detected a performance
problem.

Turn cooling system On. See Temperature Controls

•

section.
This is normal for a fully automatic defrost refrigerator.

•

The defrost cycle occurs periodically, lasting about 30
minutes.
Ensure plug is tightly pushed into outlet.

•

Check/replace fuse with a 15 amp time-delay fuse.

•

Reset circuit breaker.
Check house lights. Call local Electric Company.

•

It’s normal for the refrigerator to work longer under

•

these conditions.
It takes 8-12 hours for the refrigerator to cool down

•

completely.

Ice maker operation causes refrigerator to run slightly

•

more.
Warm air entering the refrigerator causes it to run

•

more. Open doors less often.
Ensure refrigerator is level. Keep food and containers

•

from blocking door. See PROBLEM section
OPENING/CLOSING OF DOORS/DRAWERS.

Set refrigerator control to warmer setting until

•

refrigerator temperature is satisfactory. Allow 24 hours
for temperature to stabilize.
Clean or change gasket. Leaks in door seal will cause

•

refrigerator to run longer in order to maintain desired
temperatures.

This is normal. Refrigerator goes on and off to keep

•

temperature constant.

Call your Frigidaire service representative, who can

•

interpret any messages or number codes flashing on
the digital displays.

TEMPERATURES ARE TOO COLD

Freezer temperature too
cold. Refrigerator
temperature is satisfactory.

Refrigerator temperature
too cold. Freezer
temperature is satisfactory.

Food stored in drawers
freezes.

Food stored in Meat
Keeper freezes (some
models).

Freezer control is set too cold.

•

Refrigerator control is set too

•

cold.

Refrigerator control is set too

•

cold.

Meat Keeper Temperature

•

Control set too cold.

Set freezer control to a warmer setting. Allow 24 hours

•

for temperature to stabilize.

Set refrigerator control to a warmer setting. Allow 24

•

hours for temperature to stabilize.

See solution above.

•

Adjust Meat Keeper Temperature Control to a lower

•

setting. (Meat should be stored at a temperature just
below the freezing point for maximum fresh storage
time. It is normal for ice crystals to form due to the
moisture content of meat.)

23

Before You Call

(continued)

PROBLEM CAUSE CORRECTION

TEMPERATURES ARE TOO WARM

Freezer/Refrigerator
temperature is too warm.

Freezer temperature is too
warm. Refrigerator
temperature is satisfactory.

Refrigerator temperature is
too warm. Freezer
temperature is satisfactory.

Temperature in the Meat
Keeper is too warm (some
models).

• Doors are opened too

• Door is slightly open.

•

• Refrigerator control is set too

• Meat Keeper Temperature

frequently or too long.

Freezer control is set too
warm.

warm.

Control is set too warm.

WATER/MOISTURE/FROST INSIDE REFRIGERATOR

Moisture collects on inside
of refrigerator walls.

Water collects on bottom
side of drawer cover.

Water collects in bottom of
drawer.

• Weather is hot and humid.

• Door is slightly open.

• Door is opened too often or too

long.

• Open containers.

• Vegetables contain and give

off moisture.

• Washed vegetables and fruit
drain while in the drawer.

• Warm air enters the refrigerator whenever the door is
opened. Open the door less often.

• See PROBLEM section OPENING/CLOSING OF
DOORS/DRAWERS.

Set freezer control to a colder setting. Allow 24 hours

•

for temperature to stabilize.

• Set refrigerator control to a colder setting. Allow 24
hours for temperature to stabilize.

• Adjust Meat Keeper Temperature Control to a colder
setting.

• The rate of frost buildup and internal sweating
increases.

• See PROBLEM section OPENING/CLOSING OF
DOORS/DRAWERS.

• Open door less often.

• Keep containers covered.

• It is not unusual to have moisture on the bottom side of

the cover.

• Move humidity control (some models) to lower setting.

• Dry items before putting them in the drawer. Water

collecting in bottom of drawer is normal.

WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR

Moisture collects on
outside of refrigerator or
between doors.

AUTOMATIC ICE MAKER

Ice maker is not making
any ice.

• Weather is humid.

• Door is slightly open, causing

cold air from inside refrigerator
to meet warm air from outside.

• Ice maker power switch is Off.

• Household water line valve is

not open.

• Freezer is not cold enough.

• Saddle valve on cold water

pipe is clogged or restricted by
foreign material.

• Check to see if the water
dispenser is dispensing water.

• Water filter is not completely
seated (models with filter
beside temperature control
panel).

• This is normal in humid weather. When humidity is
lower, the moisture should disappear.

• See PROBLEM section OPENING/CLOSING OF
DOORS/DRAWERS.

• Turn power switch to On (“I”) position.

• Turn on household water line valve.

• See PROBLEM section TEMPERATURES ARE TOO

WARM.

• Turn off household water line valve. Remove valve.
Ensure that valve is not a self-piercing saddle valve.
Clean valve. Replace valve if necessary.

• If not, the ice & water filter cartridge is clogged or
restricted by foreign material, and must be replaced.
Push firmly until the water filter snaps into place.

•

24

Before You Call (

continued)

PROBLEM CAUSE CORRECTION

AUTOMATIC ICE MAKER

Ice maker is not making
enough ice.

Ice maker will not stop
making ice.

Ice maker is not separating
the ice cubes.

Ice has bad odor and taste.

ICE DISPENSER

Dispenser will not dispense
ice.

Ice dispenser is jammed.

(CONTINUED)

• Ice maker is producing less ice

• Freezer is not cold enough.

• Household water line valve is

• Check to see if water

• Ice maker wire signal arm is

• Ice cubes are not being used

• Ice cubes are hollow or smaller

• Ice has picked up odor or

• Water running to ice maker

• Ice not used frequently enough.

• Ice storage container is empty.

• Freezer temperature is set too

• Household water line valve is

• Freezer door is not closed.

• Ice dispensing arm has been

• Ice has melted and frozen

• Ice cubes are jammed

• Ice cubes are frozen together.

• Ice cubes are hollow or smaller

than you expect.

not completely open.

dispenser is dispensing slower
than normal.

being held down by some item
in the freezer.

frequently enough.

than normal.

flavor from strong food stored
in refrigerator or freezer.

has poor taste or odor.

warm.

not open.

held in for more than 4-5
minutes.

around auger due to infrequent
use, temperature fluctuations,
and/or power outages.

between ice maker and back
of ice container.

than normal.

• Ice maker should produce approximately 4 – 5 pounds
of ice every 24 hours.
pounds of ice every 24 hours.

• See PROBLEM section TEMPERATURES ARE TOO
WARM.

• Turn on household water line valve.

• If it is, replace the ice & water filter cartridge.

• Move item and release wire signal arm. Remove any

ice cubes that are frozen together over the wire signal
arm.

• Remove and shake ice container to separate cubes.

• The ice & water filter cartridge may be clogged.

Replace filter cartridge.

• Cover foods tightly. Discard stale ice. Ice maker will
produce fresh supply.

• Add filter to water supply line. Consult a water
purifying company.

• Discard stale ice.

• When the first supply of ice is dropped into the

container, the dispenser should operate.

• Turn freezer control to a higher setting so that ice
cubes will be made. When first supply of ice is made,
dispenser should operate.

• Open household water line valve. Allow sufficient time
for the ice to be made. When ice is made, the
dispenser should operate.

• Ensure freezer door is closed.

• Motor is overloaded. Motor overload protector will

reset in approximately 3 minutes. Ice can then be
dispensed.

• Remove ice container, thaw, and empty the contents.
Clean container, wipe dry, and replace in proper
position. When new ice is made, dispenser should
operate.

• Remove ice cubes that are jamming the dispenser.

• Use the dispenser often so that cubes do not freeze

together.

• The ice & water filter cartridge could be clogged.
Replace the filter cartridge. Dispensing system
operates best at 20 – 100 psi water pressure. Well
water pressures should fall within this range.

Extra Ice

should produce up to 6

25

Before You Call

(continued)

PROBLEM CAUSE CORRECTION

WATER DISPENSER

Dispenser will not
dispense water.

Water has an odd taste
and/or odor.

Water pressure is
extremely low.

ODORS IN REFRIGERATOR

Interior is dirty.

OPENING/CLOSING OF DOORS/DRAWERS

Door(s) will not close.

Drawers are difficult to
move.

LIGHT BULB IS NOT ON

Light bulb is not on.

Household water line valve is

•

not open.

• Freezer door is not closed.
Ice & water filter cartridge is

•

clogged.

Front filter not fully installed, if

•

equipped

• Water has been in the tank for
a period of time.
Unit not properly connected to

•

cold water line.

• Tubing used in the household
water supply and installation
may affect water taste and
odor.
Water has a high mineral

•

content.

Cut-off and cut-on pressures

•

are too low (well systems
only).
Reverse osmosis system is in

•

regenerative phase.

Open household water line valve. See

•

section

ICE MAKER IS NOT MAKING ANY ICE

Ensure that freezer door is closed.

•

• Replace filter cartridge.

Push filter in until you hear a “click”. Filter should be

•

flush with cabinet.

• Draw and discard 10 – 12 glasses of water to freshen
the supply and completely rinse out the tank.
Connect unit to cold water line that supplies water to

•

the kitchen faucet.

• For best results, use copper tubing for water
connections.

Contact water treatment plant for help.

•

Have someone turn up the cut-off and cut-on pressure

•

on the water pump system (well systems only).

It is normal for a reverse osmosis system to be below

•

20 psi during the regenerative phase.

Interior needs to be cleaned.

•

Food with strong odors is in

•

refrigerator.

See

•

•

Care & Cleaning Chart

section.
Cover food tightly.

• Door was closed too hard,
causing other door to open
slightly.
Refrigerator is not level. It

•

rocks on the floor when moved
slightly.
Refrigerator is touching a wall

•

or cabinet.

Food is touching shelf on top

•

of drawer.
Track that drawers slide on is

•

dirty.

• Close both doors gently.

Ensure floor is level and solid, and can adequately

•

support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.
Ensure floor is level and solid, and can adequately

•

support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.

Keep less food in drawer.

•

Clean drawer, rollers, and track. See

•

Chart

in

Care and Cleaning

Light bulb is burned out.

•

Light switch is stuck.

•

• No electric current is reaching

refrigerator.

Control system has disabled

•

lights because magnet switch
trigger has been removed.

Control system has disabled

•

lights because one or both
doors were left open too long.

See

•

•

• See

• Reinstall magnet behind dairy compartment in fresh

•

Replacing Light Bulbs

section.
Release light switch located inside freezer
compartment.

PROBLEM

REFRIGERATOR.

food door.

Close and reopen door(s) to enable lights.

section

RUNNING OF

PROBLEM

in

Care and Cleaning

Care & Cleaning

section.

in

Care and Cleaning

.

26